An Investigation of Emulsion Stabilized Limestone Screenings, HR-309, 1989

During the processing of limestone to produce commercial aggregates, a significant amount of waste limestone screenings is produced. This waste material cannot be used in highway construction because it does not meet current highway specifications. The purpose of this research was to determine if a waste limestone screenings/emulsion mix could be used to construct a base capable of supporting local traffic. A 1.27 mile section of roadway in Linn County was selected for this research. The road was divided into seven sections. Six of the sections were used to test 4" and 6" compacted base thicknesses containing 2.5%, 3.5%, and 4.5% residual asphalt contents. The seventh section was a control section containing untreated waste limestone screenings.

Bituminous Mixes Prepared with Ungraded Local Aggregates, Iowa Highway Research Board Bulletin No. 19, 1960

Joint Publications from Iowa Engineering Experiment Station - Bulletin No. 190 and Iowa Highway Research Board - Bulletin No. 19. This bulletin is a report on the development of bituminous paving mixtures containing various local materials and asphaltic binders. The laboratory investigations described in this bulletin were performed as part of Iowa Highway Research Board project HR-20, "Treating Loess, Fine Sands, and Limestone Dusts With Liquid Binders." This project was awarded to the Iowa Engineering Experiment Station of Iowa State University in 1952, and continued to June, 1958.

Motor Grader Operator Maintenance of Granular Surfaced Roads : Tips from Iowa Operators, 1991

This booklet is a compilation of notes taken during motor grader operators workshops held at some 20 different locations throughout Iowa during the last two years. It is also the advice of 16 experienced motor grader operators and maintenance foremen (from 14 different counties around Iowa), who serve as instructors and assistant instructors at the "MoGo" workshops. The instructors have all said that they learn as much from the operators who attend the workshops as they impart. Motor grader operators from throughout Iowa have shown us new, innovative and better ways of maintaining gravel roads. This booklet is an attempt to pass on some of these "tips" that we have gathered from Iowa operators. It will need to be revised, corrected, and added to based on the advice we get from you, the operators who do the work here in Iowa.

The Effect of Deicing Salt on Aggregate Durability, Progress Report HR-266, 1985

The Iowa DOT has been using rapid freezing in air and thawing in water to evaluate coarse aggregate durability in concrete since 1962. Earlier research had shown that the aggregate pore system was a major factor in susceptibility to D-cracking rapid deterioration. There are cases were service records show rapid deterioration of concrete containing certain aggregates on heavily salted primary roads and relatively good performance with the same aggregate in secondary pavements with limited use of deicing salt. A five-cycle salt treatment of the coarse aggregate prior to durability testing has yielded durability factors that correlate with aggregate service records on heavily salted primary pavements. X-ray fluorescence analyses have shown that sulfur contents correlate well with aggregate durabilities with higher sulfur contents producing poor durability. Trial additives that affect the salt treatment durabilities would indicate that one factor in the rapid deterioration mechanism is an adverse chemical reaction. The objective· of the current research is to develop a simple method of determining aggregate susceptibility to salt related deterioration. This method of evaluation includes analyses of both the pore system and chemical composition.

Investigation of Rapid Thermal Analysis Procedures for Prediction of the Service Life of PCCP Carbonate Coarse Aggregate: Phase I, Progress Report, HR-337, 1992

The major objective of this research project is to utilize thermal analysis techniques in conjunction with x-ray analysis methods to identify and explain chemical reactions that promote aggregate related deterioration in Portland cement concrete. The first year of this project has been spent obtaining and analyzing limestone and dolomite samples that exhibit a wide range of field service performance. Most of the samples chosen for the study also had laboratory durability test information (ASTM C 666, method B) that was readily available. Preliminary test results indicate that a strong relationship exists between the average crystallite size of the limestone (calcite) specimens and their apparent decomposition temperatures as measured by thermogravimetric analysis. Also, premature weight loss in the thermogravimetric analysis tests appeared to be related to the apparent decomposition temperature of the various calcite test specimens.

Ammonium Phosphate/Fly Ash Road Base Construction, HR-294, Construction Report, 1987

The objective of this research project was to evaluate the construction and service performance of ammonium phosphate/fly ash (APFA) treated base courses of crushed fines and/or unprocessed sand. Specific test results related to construction of the test sections were included in the 1987 construction report by Iowa State University. The performance of the experimental sections is dealt with in this final report. This 1986 project demonstrated that in all cases the control sections utilizing a Type B base experienced dramatically less cracking in the surface than the APFA treated base sections. The cost per mix and subsequent surface maintenance costs for the APFA base sections, especially those having a substantial amount of limestone, were higher than the Type B base control sections. This type of construction may prove to be economical only when petroleum product costs escalate.

Granular Base Materials for Flexible Pavements, HR-131, 1970

The coefficients of relative strength (CORS) of base courses for use in the American association state highway officials (AASHO) interim guide for the design of flexible pavements are determined here. Based on (1) volumetric strain--axial strain relationships at minimum volume, and (2) effective stress ratio-cohesion relationships at maximum effective stress ratio, CORS were determined from the results of laboratory triaxial tests on both asphalt-treated and untreated aggregate base course materials. The researchers conclude that volumetric strain-axial strain at minimum volume appear to be appropriate parameters for determining CORS.

The Relationship of Aggregate Durability to Trace Element Content, Interim Report, HR-266, 1984

This report is a brief overview of the recent Iowa Department of Transportation research in the area of durability of Portland cement, concrete under the direction of Wendeli Dubberke. Present plans are to publish a more detailed report on low Portland cement concrete- durability research in January, 1985.

Investigation of PCC Pavement Deterioration: A Few Facts are Worth More than 100 Opinions, Interim Report, HR-2074, 1995

Portland Cement Concrete (PCC) pavement has served the State of Iowa well for many years. The oldest Iowa pavement was placed in LeMars in 1904. Beginning in 1931, many miles of PCC pavement were built to "get out of the mud.” Many of these early pavements provided good performance without deterioration for more than 50 years. In the late 1950's, Iowa was faced with severe PCC pavement deterioration referred to as D cracking. Research identified the cause of this deterioration as crushed limestone containing a bad pore system. Selective quarrying and ledge control has alleviated this problem. In 1990, cracking deterioration was identified on a three year old pavement on us 20 in central Iowa. The coarse aggregate was a crushed limestone with an excellent history of performance in PCC pavement. Examination of cores showed very few cracks through the coarse aggregate particles. The cracks were predominately confined to the matrix. The deterioration was identified as alkali-silica reactivity (ASR) by a consultant.

3D crosshole ERT for aquifer characterization and monitoring of infiltrating river water

The hydrogeological properties and responses of a productive aquifer in northeastern Switzerland are investigated. For this purpose, 3D crosshole electrical resistivity tomography (ERT) is used to define the main lithological structures within the aquifer (through static inversion) and to monitor the water infiltration from an adjacent river. During precipitation events and subsequent river flooding, the river water resistivity increases. As a consequence, the electrical characteristics of the infiltrating water can be used as a natural tracer to delineate preferential flow paths and flow velocities. The focus is primarily on the experiment installation, data collection strategy, and the structural characterization of the site and a brief overview of the ERT monitoring results. The monitoring system comprises 18 boreholes each equipped with 10 electrodes straddling the entire thickness of the gravel aquifer. A multi-channel resistivity system programmed to cycle through various four-point electrode configurations of the 180 electrodes in a rolling sequence allows for the measurement of approximately 15,500 apparent resistivity values every 7 h on a continuous basis. The 3D static ERT inversion of data acquired under stable hydrological conditions provides a base model for future time-lapse inversion studies and the means to investigate the resolving capability of our acquisition scheme. In particular, it enables definition of the main lithological structures within the aquifer. The final ERT static model delineates a relatively high-resistivity, low-porosity, intermediate-depth layer throughout the investigated aquifer volume that is consistent with results from well logging and seismic and radar tomography models. The next step will be to define and implement an appropriate time-lapse ERT inversion scheme using the river water as a natural tracer. The main challenge will be to separate the superposed time-varying effects of water table height, temperature, and salinity variations associated with the infiltrating water.

Textural controls on induced polarization and permeability in granular media

The spatial resolution visualized with hydrological models and the conceptualized images of subsurface hydrological processes often exceed resolution of the data collected with classical instrumentation at the field scale. In recent years it was possible to increasingly diminish the inherent gap to information from point like field data through the application of hydrogeophysical methods at field-scale. With regards to all common geophysical exploration techniques, electric and electromagnetic methods have arguably to greatest sensitivity to hydrologically relevant parameters. Of particular interest in this context are induced polarisation (IP) measurements, which essentially constrain the capacity of a probed subsurface region to store an electrical charge. In the absence of metallic conductors the IP- response is largely driven by current conduction along the grain surfaces. This offers the perspective to link such measurements to the characteristics of the solid-fluid-interface and thus, at least in unconsolidated sediments, should allow for first-order estimates of the permeability structure.¦While the IP-effect is well explored through laboratory experiments and in part verified through field data for clay-rich environments, the applicability of IP-based characterizations to clay-poor aquifers is not clear. For example, polarization mechanisms like membrane polarization are not applicable in the rather wide pore-systems of clay free sands, and the direct transposition of Schwarz' theory relating polarization of spheres to the relaxation mechanism of polarized cells to complex natural sediments yields ambiguous results.¦In order to improve our understanding of the structural origins of IP-signals in such environments as well as their correlation with pertinent hydrological parameters, various laboratory measurements have been conducted. We consider saturated quartz samples with a grain size spectrum varying from fine sand to fine gravel, that is grain diameters between 0,09 and 5,6 mm, as well as corresponding pertinent mixtures which can be regarded as proxies for widespread alluvial deposits. The pore space characteristics are altered by changing (i) the grain size spectra, (ii) the degree of compaction, and (iii) the level of sorting. We then examined how these changes affect the SIP response, the hydraulic conductivity, and the specific surface area of the considered samples, while keeping any electrochemical variability during the measurements as small as possible. The results do not follow simple assumptions on relationships to single parameters such as grain size. It was found that the complexity of natural occurring media is not yet sufficiently represented when modelling IP. At the same time simple correlation to permeability was found to be strong and consistent. Hence, adaptations with the aim of better representing the geo-structure of natural porous media were applied to the simplified model space used in Schwarz' IP-effect-theory. The resulting semi- empiric relationship was found to more accurately predict the IP-effect and its relation to the parameters grain size and permeability. If combined with recent findings about the effect of pore fluid electrochemistry together with advanced complex resistivity tomography, these results will allow us to picture diverse aspects of the subsurface with relative certainty. Within the framework of single measurement campaigns, hydrologiste can than collect data with information about the geo-structure and geo-chemistry of the subsurface. However, additional research efforts will be necessary to further improve the understanding of the physical origins of IP-effect and minimize the potential for false interpretations.¦-¦Dans l'étude des processus et caractéristiques hydrologiques des subsurfaces, la résolution spatiale donnée par les modèles hydrologiques dépasse souvent la résolution des données du terrain récoltées avec des méthodes classiques d'hydrologie. Récemment il est possible de réduire de plus en plus cet divergence spatiale entre modèles numériques et données du terrain par l'utilisation de méthodes géophysiques, notamment celles géoélectriques. Parmi les méthodes électriques, la polarisation provoquée (PP) permet de représenter la capacité des roches poreuses et des sols à stocker une charge électrique. En l'absence des métaux dans le sous-sol, cet effet est largement influencé par des caractéristiques de surface des matériaux. En conséquence les mesures PP offrent une information des interfaces entre solides et fluides dans les matériaux poreux que nous pouvons lier à la perméabilité également dirigée par ces mêmes paramètres. L'effet de la polarisation provoquée à été étudié dans différentes études de laboratoire, ainsi que sur le terrain. A cause d'une faible capacité de polarisation des matériaux sableux, comparé aux argiles, leur caractérisation par l'effet-PP reste difficile a interpréter d'une manière cohérente pour les environnements hétérogènes.¦Pour améliorer les connaissances sur l'importance de la structure du sous-sol sableux envers l'effet PP et des paramètres hydrologiques, nous avons fait des mesures de laboratoire variées. En détail, nous avons considéré des échantillons sableux de quartz avec des distributions de taille de grain entre sables fins et graviers fins, en diamètre cela fait entre 0,09 et 5,6 mm. Les caractéristiques de l'espace poreux sont changées en modifiant (i) la distribution de taille des grains, (ii) le degré de compaction, et (iii) le niveau d'hétérogénéité dans la distribution de taille de grains. En suite nous étudions comment ces changements influencent l'effet-PP, la perméabilité et la surface spécifique des échantillons. Les paramètres électrochimiques sont gardés à un minimum pendant les mesures. Les résultats ne montrent pas de relation simple entre les paramètres pétro-physiques comme par exemples la taille des grains. La complexité des media naturels n'est pas encore suffisamment représenté par les modèles des processus PP. Néanmoins, la simple corrélation entre effet PP et perméabilité est fort et consistant. En conséquence la théorie de Schwarz sur l'effet-PP a été adapté de manière semi-empirique pour mieux pouvoir estimer la relation entre les résultats de l'effet-PP et les paramètres taille de graines et perméabilité. Nos résultats concernant l'influence de la texture des matériaux et celles de l'effet de l'électrochimie des fluides dans les pores, permettront de visualiser des divers aspects du sous-sol. Avec des telles mesures géo-électriques, les hydrologues peuvent collectionner des données contenant des informations sur la structure et la chimie des fluides des sous-sols. Néanmoins, plus de recherches sur les origines physiques de l'effet-PP sont nécessaires afin de minimiser le risque potentiel d'une mauvaise interprétation des données.

Sediment budget monitoring of a debris-flow torrent (French Prealps)

The Manival near Grenoble (French Prealps) is a very active debris-flow torrent equipped with a large sediment trap (25 000 m3) protecting an urbanized alluvial fan from debris-flows. We began monitoring the sediment budget of the catchment controlled by the trap in Spring 2009. Terrestrial laser scanner is used for monitoring topographic changes in a small gully, the main channel, and the sediment trap. In the main channel, 39 cross-sections are surveyed after every event. Three periods of intense geomorphic activity are documented here. The first was induced by a convective storm in August 2009 which triggered a debris-flow that deposited ~1,800 m3 of sediment in the trap. The debris-flow originated in the upper reach of the main channel and our observations showed that sediment outputs were entirely supplied by channel scouring. Hillslope debris-flows were initiated on talus slopes, as revealed by terrestrial LiDAR resurveys; however they were disconnected to the main channel. The second and third periods of geomorphic activity were induced by long duration and low intensity rainfall events in September and October 2009 which generate small flow events with intense bedload transport. These events contribute to recharge the debris-flow channel with sediments by depositing important gravel dunes propagating from headwaters. The total recharge in the torrent subsequent to bedload transport events was estimated at 34% of the sediment erosion induced by the August debris-flow.

Metsäteollisuuden lentotuhkien laadun vaikutus hyötykäyttösovellutuksiin

Työn tavoitteena oli kartoittaa metsäteollisuuden tuotantolaitoksissa syntyvän lentotuhkan laadun vaikutusta hyötykäyttökohteisiin. Hyötykäyttökohteista tarkasteltiin tuhkien soveltumista maarakentamiseen, päällystettyyn- ja peitettyyn rakenteeseen, pelto- ja puutarhakäyttöön, maisemointiin ja viherrakentamiseen sekä metsäkäyttöön. Tuhka-analyysien tietojen perusteella tuhkalle määritettiin mahdollinen hyötykäyttökohde verrattaessa niitä lainsäädännönasettamiin raja-arvoihin jokaisessa hyötykäyttökohteessa. Lisäksi tarkasteltiinmahdollisia esteitä tuhkan käytölle tietyissä hyötykäyttökohteissa sekä pyrittiin saamaan tuhkalle järkevämpi loppusijoituspaikka kuin kaatopaikka. Kirjallisuusosaan on koottu metsäteollisuudessa käytössä olevat polttomenetelmät sekä poltettavat raaka-aineet. Eri polttojakeiden tuhkien koostumuksista on tehty yhteenveto kirjallisuudesta löytyvien tietojen perusteella. Lisäksi kirjallisuusosassa on esitetty lentotuhkan fraktiointimenetelmiä sekä eri hyötykäyttökohteet ja niiden vaatimukset lentotuhkalta. Kokeellisessa osassa on vertailtu olemassa olevien tuhkanäytteiden haitta-aineiden pitoisuuksia eri hyötykäyttökohteiden vaadittuihin raja-arvoihin. Tähän työhön valittiin viisi eri metsäteollisuuden tuotantolaitosta Suomesta ja niille jokaiselle pyrittiin löytämään parhaiten soveltuva loppukäyttö. Metsäteollisuuden tuotantolaitoksilla poltetaan useita eri polttojakeita. Lisäksi polttoainekoostumus ja -määrä vaihtelevat vuositasolla. Tämä vaikuttaa tuhkan laatuun ja vaikeuttaa tuhkan hyödyntämistä eri hyötykäyttökohteissa. Jokaiselle tuhkan eri hyötykäyttökohteelle on säädetty omat raja-arvonsa, joka rajoittaa tuhkan hyötykäyttöä. Tällä hetkellä tuhkaa hyödynnetään eniten metsälannoitteena, jolloin puuaineksen mukana poistuneet ravinteet saadaan palautettua takaisin luontoon. Myös tuhkan hyödyntäminen maarakentamisessa on järkevää, koska silloin korvataan maa-ainesta tuhkalla ja vältytään kaatopaikkasijoittamiselta. Yleisesti pelto- ja puutarhakäyttöä ajatellen raja-arvot ovat liian tiukat metsäteollisuuden lentotuhkalle.

Sediment budget monitoring of debris-flow and bedload transport in the Manival Torrent, SE France

Steep mountain catchments typically experience large sediment pulses from hillslopes which are stored in headwater channels and remobilized by debris-flows or bedload transport. Event-based sediment budget monitoring in the active Manival debris-flow torrent in the French Alps during a two-year period gave insights into the catchment-scale sediment routing during moderate rainfall intensities which occur several times each year. The monitoring was based on intensive topographic resurveys of low- and high-order channels using different techniques (cross-section surveys with total station and high-resolution channel surveys with terrestrial and airborne laser scanning). Data on sediment output volumes from the main channel were obtained by a sediment trap. Two debris-flows were observed, as well as several bedload transport flow events. Sediment budget analysis of the two debris-flows revealed that most of the debris-flow volumes were supplied by channel scouring (more than 92%). Bedload transport during autumn contributed to the sediment recharge of high-order channels by the deposition of large gravel wedges. This process is recognized as being fundamental for debris-flow occurrence during the subsequent spring and summer. A time shift of scour-and-fill sequences was observed between low- and high-order channels, revealing the discontinuous sediment transfer in the catchment during common flow events. A conceptual model of sediment routing for different event magnitude is proposed.

Application des méthodes géophysiques à l'étude de deux sites (Kappelen et Grenchen) de l'aquifère poreux complexe du Seeland

L'aquifère du Seeland représente une richesse en ressources hydriques qu'il est impératif de préserver contre tout risque de détérioration. Cet aquifère prolifique est constitué principalement de sédiments alluviaux post-glaciaires (graviers, sables et limons). Il est soumis aux contraintes environnementales des pratiques d'agriculture intensive, du réseau routier, des villes et de leurs activités industrielles. La connaissance optimale de ces ressources est donc primordiale pour leur protection. Dans cette optique, deux sites Kappelen et Grenchen représentatifs de l'aquifère du Seeland ont été étudiés. L'objectif de ce travail est de caractériser d'un point de vue hydrogéophysique l'aquifère au niveau de ces deux sites, c'est-à-dire, comprendre la dynamique des écoulements souterrains par l'application des méthodes électriques de surface associées aux diagraphies en intégrant des méthodes hydrogéologiques. Pour le site de Kappelen, les méthodes électriques de surface ont permis d'identifier les différents faciès géoélectriques en présence et de mettre en évidence leur disposition en une structure tabulaire et horizontale. Il s'agit d'un aquifère libre constitué d'une série de graviers allant jusqu'à 15 m de profondeur reposant sur de la moraine argileuse. Les diagraphies électriques, nucléaires et du fluide ont servis à la détermination des caractéristiques pétrophysiques et hydrauliques de l'aquifère qui contrôlent son comportement hydrodynamique. Les graviers aquifères de Kappelen présentent deux minéraux dominants: quartz et calcite. Les analyses minéralogiques indiquent que ces deux éléments constituent 65 à 75% de la matrice. La porosité totale obtenue par les diagraphies nucléaires varie de 20 à 30 %, et de 22 à 29 % par diagraphies électrique. Avec les faibles valeurs de Gamma Ray ces résultats indiquent que l'aquifère des graviers de Kappelen est dépourvu d'argile minéralogique. La perméabilité obtenue par diagraphies du fluide varie de 3.10-4 à 5.10-2 m/s, et par essais de pompage de 10-4 à 10-2 m/s. Les résultats des analyses granulométriques indiquent une hétérogénéité granulométrique au niveau des graviers aquifères. La fraction de sables, sables très fins, silts et limons constitue de 10 à 40 %. Ces éléments jouent un rôle important dans le comportement hydraulique de l'aquifère. La porosité efficace de 11 à 25% estimée à partir des résultats des analyses granulométriques suppose que les zones les plus perméables correspondent aux zones les plus graveleuses du site. Etablie sur le site de Kappelen, cette méthodologie a été utilisée sur le site de Grenchen. Les méthodes électriques de surface indiquent que l'aquifère captif de Grenchen est constitué des sables silteux comprenant des passages sableux, encadrés par des silts argileux imperméables. L'aquifère de Grenchen est disposé dans une structure relativement tabulaire et horizontale. Son épaisseur totale peut atteindre les 25 m vers le sud et le sud ouest ou les passages sableux sont les plus importants. La détermination des caractéristiques pétrophysiques et hydrauliques s'est faite à l'aide des diagraphies. Les intensités Gamma Ray varient de 30 à 100 cps, les plus fortes valeurs n'indiquent qu'une présence d'éléments argileux mais pas de bancs d'argile. Les porosités totales de 15 à 25% et les densités globales de 2.25 à 2.45 g/cm3 indiquent que la phase minérale (matrice) est composée essentiellement de quartz et de calcaire. Les densités de matrice varient entre 2.65 et 2.75 g/cm3. La perméabilité varie de 2 10-6 à 5 10-4 m/s. La surestimation des porosités totales à partir des diagraphies électriques de 25 à 42% est due à la présence d'argiles. -- The vast alluvial Seeland aquifer system in northwestern Switzerland is subjected to environmental challenges due to intensive agriculture, roads, cities and industrial activities. Optimal knowledge of the hydrological resources of this aquifer system is therefore important for their protection. Two representative sites, Kappelen and Grenchen, of the Seeland aquifer were investigated using surface-based geoelectric methods and geophysical borehole logging methods. By integrating of hydrogeological and hydrogeophysical methods, a reliable characterization of the aquifer system at these two sites can be performed in order to better understand the governing flow and transport process. At the Kappelen site, surface-based geoelectric methods allowed to identify various geoelectric facies and highlighted their tabular and horizontal structure. It is an unconfined aquifer made up of 15 m thick gravels with an important sandy fraction and bounded by a shaly glacial aquitard. Electrical and nuclear logging measurements allow for constraining the petrophysical and hydrological parameters of saturated gravels. Results indicate that in agreement with mineralogical analyses, matrix of the probed formations is dominated by quartz and calcite with densities of 2.65 and 2.71 g/cc, respectively. These two minerals constitute approximately 65 to 75 % of the mineral matrix. Matrix density values vary from 2.60 to 2.75 g/cc. Total porosity values obtained from nuclear logs range from 20 to 30 % and are consistent with those obtained from electrical logs ranging from 22 to 29 %. Together with the inherently low natural gamma radiation and the matrix density values obtained from other nuclear logging measurements, this indicates that at Kappelen site the aquifer is essentially devoid of clay. Hydraulic conductivity values obtained by the Dilution Technique vary between 3.10-4 and 5.10-2 m/s, while pumping tests give values ranging from 10-4 to 10-2 m/s. Grain size analysis of gravel samples collected from boreholes cores reveal significant granulometric heterogeneity of these deposits. Calculations based on these granulometric data have shown that the sand-, silt- and shale-sized fractions constitute between 10 and 40 % of the sample mass. The presence of these fine elements in general and their spatial distribution in particular are important as they largely control the distribution of the total and effective porosity as well as the hydraulic conductivity. Effective porosity values ranging from 11 to 25% estimated from grain size analyses indicate that the zones of higher hydraulic conductivity values correspond to the zones dominated by gravels. The methodology established at the Kappelen site was then applied to the Grenchen site. Results from surface-based geoelectric measurements indicate that it is a confined aquifer made up predominantly of shaly sands with intercalated sand lenses confined impermeable shally clay. The Grenchen confined aquifer has a relatively tabular and horizontal structure with a maximum thickness of 25 m in the south and the southwest with important sand passages. Petrophysical and hydrological characteristics were performed using electrical and nuclear logging. Natural gamma radiation values ranging from 30 to 100 cps indicate presence of a clay fraction but not of pure clay layers. Total porosity values obtained from electrical logs vary form 25 to 42%, whereas those obtained from nuclear logs values vary from 15 to 25%. This over-estimation confirms presences of clays. Density values obtained from nuclear logs varying from 2.25 to 2.45 g/cc in conjunction with the total porosity values indicate that the dominating matrix minerals are quartz and calcite. Matrix density values vary between 2.65 and 2.75 g/cc. Hydraulic conductivity values obtained by the Dilution Technique vary from 2 10-6 to 5 10-4 m/s.