Multipath policy routing in packet switched networks

Dissertação apresentada para obtenção do Grau de Mestre em Engenharia Electrotécnica e de Computadores, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

A 1.2 V low noise amplifier with double feedback for high gain and low noise figure

Dissertação para obtenção do Grau de Mestre em Engenharia Eletrotécnica e de Computadores

Maintaining the correctness of transactional memory programs

Dissertação para obtenção do Grau de Doutor em Engenharia Informática

Planning and verification of multipath routing protocols

Conventionally the problem of the best path in a network refers to the shortest path problem. However, for the vast majority of networks present nowadays this solution has some limitations which directly affect their proper functioning, as well as an inefficient use of their potentialities. Problems at the level of large networks where graphs of high complexity are commonly present as well as the appearing of new services and their respective requirements, are intrinsically related to the inability of this solution. In order to overcome the needs present in these networks, a new approach to the problem of the best path must be explored. One solution that has aroused more interest in the scientific community considers the use of multiple paths between two network nodes, where they can all now be considered as the best path between those nodes. Therefore, the routing will be discontinued only by minimizing one metric, where only one path between nodes is chosen, and shall be made by the selection of one of many paths, thereby allowing the use of a greater diversity of the present paths (obviously, if the network consents). The establishment of multi-path routing in a given network has several advantages for its operation. Its use may well improve the distribution of network traffic, improve recovery time to failure, or it can still offer a greater control of the network by its administrator. These factors still have greater relevance when networks have large dimensions, as well as when their constitution is of high complexity, such as the Internet, where multiple networks managed by different entities are interconnected. A large part of the growing need to use multipath protocols is associated to the routing made based on policies. Therefore, paths with different characteristics can be considered with equal level of preference, and thus be part of the solution for the best way problem. To perform multi-path routing using protocols based only on the destination address has some limitations but it is possible. Concepts of graph theory of algebraic structures can be used to describe how the routes are calculated and classified, enabling to model the routing problem. This thesis studies and analyzes multi-path routing protocols from the known literature and derives a new algebraic condition which allows the correct operation of these protocols without any network restriction. It also develops a range of software tools that allows the planning and the respective verification/validation of new protocols models according to the study made.

Design of a low-voltage CMOS RF receiver for energy harvesting sensor node

In this thesis a CMOS low-power and low-voltage RF receiver front-end is presented. The main objective is to design this RF receiver so that it can be powered by a piezoelectric energy harvesting power source, included in a Wireless Sensor Node application. For this type of applications the major requirements are: the low-power and low-voltage operation, the reduced area and cost and the simplicity of the architecture. The system key blocks are the LNA and the mixer, which are studied and optimized with greater detail, achieving a good linearity, a wideband operation and a reduced introduction of noise. A wideband balun LNA with noise and distortion cancelling is designed to work at a 0.6 V supply voltage, in conjunction with a double-balanced passive mixer and subsequent TIA block. The passive mixer operates in current mode, allowing a minimal introduction of voltage noise and a good linearity. The receiver analog front-end has a total voltage conversion gain of 31.5 dB, a 0.1 - 4.3 GHz bandwidth, an IIP3 value of -1.35 dBm, and a noise figure lower than 9 dB. The total power consumption is 1.9 mW and the die area is 305x134.5 m2, using a standard 130 nm CMOS technology.

As práticas comerciais desleais

The following study aims to examine a controversial and relatively unexplored subject within our system: the legal framework on unfair business-to-consumer commercial practices. Given the fact that this subject is based on the Directive 2005/29/EC, we considered to be appropriate to explore, firstly, the background and origin of such normative instrument. Nevertheless, we have centered our analysis on the interpretation of the set rules established by the Portuguese legal system (Law nr 57/2008, March 26th). For this dissertation, we have proposed a model of tripartite approach. Chapter V seeks to shed light on the general clause by analyzing a set of open concepts such as professional diligence, honest market practice, good faith or material distortion of the consumer’s economic behavior. In chapter VI, we will focus on two common types of unfair commercial practices: misleading and aggressive practices. Finally, due to the fact that chapter VII deals with the black list, we have illustrated the listed practices by giving real life examples. Taking into account the indefinite concepts used in the general prohibition and in the misleading and aggressive clauses, it is particularly difficult to demonstrate the unfairness of the professional’s behavior. In the light of this information, we have concluded that the regime fails on achieving its main goal: it does not protect proper and effectively the consumer’s interests.

Prevalence of Chagas disease in blood donors at the Uberaba Regional Blood Center, Brazil, from 1995 to 2009

INTRODUCTION: A retrospective study was conducted to assess the occurrence of blood donations that were ineligible due to Chagas disease infection from 1995 to 2009 at the Uberaba Regional Blood Center (HRU), Brazil, verify the tendency of this ineligibility, and describe the epidemiologic profile of the donors. METHODS: Retrospective studies of serological ineligibility due to Chagas disease, statistical analysis by means of the chi-square test and odds ratio, study of the tendencies using a dispersion graph and the linear correlation coefficient (r) were performed. RESULTS: In the period under study, a 0.2% serum prevalence of ineligibility due to Chagas disease was found, with a significant drop in ineligible donations from 2001 to 2009. Among the serum positive-donors, there was a significant predominance among those aged 30 years or above and non-single individuals. CONCLUSIONS: The results show a rate of occurrence that is lower than that described in literature, as well as a progressive drop during the 15 years under assessment. Such results are a consequence of systematic combat of the vector since the 70s and the progressive and consistent increase of returning donors, resulting in a drop of the contamination risk factor by means of blood transfusion and in the improvement of the quality of hemotherapy practices in the HRU.

Switching mode power amplifier for bluetooth applications

Modern fully integrated transceivers architectures, require circuits with low area, low cost, low power, and high efficiency. A key block in modern transceivers is the power amplifier, which is deeply studied in this thesis. First, we study the implementation of a classical Class-A amplifier, describing the basic operation of an RF power amplifier, and analysing the influence of the real models of the reactive components in its operation. Secondly, the Class-E amplifier is deeply studied. The different types of implementations are reviewed and theoretical equations are derived and compared with simulations. There were selected four modes of operation for the Class-E amplifier, in order to perform the implementation of the output stage, and the subsequent comparison of results. This led to the selection of the mode with the best trade-off between efficiency and harmonics distortion, lower power consumption and higher output power. The optimal choice was a parallel circuit containing an inductor with a finite value. To complete the implementation of the PA in switching mode, a driver was implemented. The final block (output stage together with the driver) got 20 % total efficiency (PAE) transmitting 8 dBm output power to a 50 W load with a total harmonic distortion (THD) of 3 % and a total consumption of 28 mW. All implementations are designed using standard 130 nm CMOS technology. The operating frequency is 2.4 GHz and it was considered an 1.2 V DC power supply. The proposed circuit is intended to be used in a Bluetooth transmitter, however, it has a wider range of applications.

Wideband CMOS low noise amplifiers

Modern fully integrated receiver architectures, require inductorless circuits to achieve their potential low area, low cost, and low power. The low noise amplifier (LNA), which is a key block in such receivers, is investigated in this thesis. LNAs can be either narrowband or wideband. Narrowband LNAs use inductors and have very low noise figure, but they occupy a large area and require a technology with RF options to obtain inductors with high Q. Recently, wideband LNAs with noise and distortion cancelling, with passive loads have been proposed, which can have low NF, but have high power consumption. In this thesis the main goal is to obtain a very low area, low power, and low-cost wideband LNA. First, it is investigated a balun LNA with noise and distortion cancelling with active loads to boost the gain and reduce the noise figure (NF). The circuit is based on a conventional balun LNA with noise and distortion cancellation, using the combination of a common-gate (CG) stage and common-source (CS) stage. Simulation and measurements results, with a 130 nm CMOS technology, show that the gain is enhanced by about 3 dB and the NF is reduced by at least 0.5 dB, with a negligible impact on the circuit linearity (IIP3 is about 0 dBm). The total power dissipation is only 4.8 mW, and the active area is less than 50 x 50 m2 . It is also investigated a balun LNA in which the gain is boosted by using a double feedback structure.We propose to replace the load resistors by active loads, which can be used to implement local feedback loops (in the CG and CS stages). This will boost the gain and reduce the noise figure (NF). Simulation results, with the same 130 nm CMOS technology as above, show that the gain is 24 dB and NF is less than 2.7 dB. The total power dissipation is only 5.4 mW (since no extra blocks are required), leading to a figure-of-merit (FoM) of 3.8 mW

Different doses of exogenous surfactant for treatment of meconium aspiration syndrome in newborn rabbits

OBJECTIVE: To evaluate the effects of 2 different doses of exogenous surfactant on pulmonary mechanics and on the regularity of pulmonary parenchyma inflation in newborn rabbits. METHOD: Newborn rabbits were submitted to tracheostomy and randomized into 4 study groups: the Control group did not receive any material inside the trachea; the MEC group was instilled with meconium, without surfactant treatment; the S100 and S200 groups were instilled with meconium and were treated with 100 and 200 mg/kg of exogenous surfactant (produced by Instituto Butantan) respectively. Animals from the 4 groups were mechanically ventilated during a 25-minute period. Dynamic compliance, ventilatory pressure, tidal volume, and maximum lung volume (P-V curve) were evaluated. Histological analysis was conducted using the mean linear intercept (Lm), and the lung tissue distortion index (SDI) was derived from the standard deviation of the means of the Lm. One-way analysis of variance was used with a = 0.05. RESULTS: After 25 minutes of ventilation, dynamic compliance (mL/cm H2O · kg) was 0.87 ± 0.07 (Control); 0.49 ± 0.04 (MEC*); 0.67 ± 0.06 (S100); and 0.67 ± 0.08 (S200), and ventilatory pressure (cm H2O) was 9.0 ± 0.9 (Control); 16.5 ± 1.7 (MEC*); 12.4 ± 1.1 (S100); and 12.1 ± 1.5 (S200). Both treated groups had lower Lm values and more homogeneity in the lung parenchyma compared to the MEC group: SDI = 7.5 ± 1.9 (Control); 11.3 ± 2.5 (MEC*), 5.8 ± 1.9 (S100); and 6.7 ± 1.7 (S200) (*P < 0.05 versus all the other groups). CONCLUSIONS: Animals treated with surfactant showed significant improvement in pulmonary mechanics and more regularity of the lung parenchyma in comparison to untreated animals. There was no difference in results after treatment with either of the doses used.

Ações encobertas

The global and increasingly technological society requires the States to adopt security measures that can maintain the balance between the freedom, on the one hand, and the security and the respect for fundamental rights of a democratic state, on the other. A State can only achieve this aim if it has an effective judicial system and in particular a criminal procedure adequate to the new criminogenic realities. In this context, the national legislator has adopted, following other international legal systems, special means of obtaining proof more stringent of rights. Within those special means are included the covert actions, that, being a means to use sparingly, is a key element to fight against violent and highly organized crime. Therefore, the undercover agent, voluntary by nature, develops a set of activities that enables the investigation to use other means of taking evidence and/or probationary diligences itself, with the purpose of providing sufficient proof to the case file. In this milieu, given the high risks involved during the investigation, as well as after its completion, the undercover agent can act upon fictitious identity. This measure can be maintained during the evidentiary phase of the trial. Similarly, given the latent threat that the undercover agent suffers by its inclusion in criminal organizations, as well as the need for his inclusion in future covert actions it is crucial that his participation as a witness in the trial is properly shielded. Thus, when the undercover agent provides, exceptionally, statements in the trial, he shall do so always through videoconference with voice and image distortion. This measure can guarantee the anonymity of the undercover agent and concomitantly, that the adversarial principle and the right of the accused to a fair trial is not prejudiced since, in those circumstances, the diligence will be supervised in its entirety (in the audience and with the undercover agent) by a judge.

Frequency-domain receiver design for doubly-selective channels

This work is devoted to the broadband wireless transmission techniques, which are serious candidates to be implemented in future broadband wireless and cellular systems, aiming at providing high and reliable data transmission and concomitantly high mobility. In order to cope with doubly-selective channels, receiver structures based on OFDM and SC-FDE block transmission techniques, are proposed, which allow cost-effective implementations, using FFT-based signal processing. The first subject to be addressed is the impact of the number of multipath components, and the diversity order, on the asymptotic performance of OFDM and SC-FDE, in uncoded and for different channel coding schemes. The obtained results show that the number of relevant separable multipath components is a key element that influences the performance of OFDM and SC-FDE schemes. Then, the improved estimation and detection performance of OFDM-based broadcasting systems, is introduced employing SFN (Single Frequency Network) operation. An initial coarse channel is obtained with resort to low-power training sequences estimation, and an iterative receiver with joint detection and channel estimation is presented. The achieved results have shown very good performance, close to that with perfect channel estimation. The next topic is related to SFN systems, devoting special attention to time-distortion effects inherent to these networks. Typically, the SFN broadcast wireless systems employ OFDM schemes to cope with severely time-dispersive channels. However, frequency errors, due to CFO, compromises the orthogonality between subcarriers. As an alternative approach, the possibility of using SC-FDE schemes (characterized by reduced envelope fluctuations and higher robustness to carrier frequency errors) is evaluated, and a technique, employing joint CFO estimation and compensation over the severe time-distortion effects, is proposed. Finally, broadband mobile wireless systems, in which the relative motion between the transmitter and receiver induces Doppler shift which is different or each propagation path, is considered, depending on the angle of incidence of that path in relation to the direction of travel. This represents a severe impairment in wireless digital communications systems, since that multipath propagation combined with the Doppler effects, lead to drastic and unpredictable fluctuations of the envelope of the received signal, severely affecting the detection performance. The channel variations due this effect are very difficult to estimate and compensate. In this work we propose a set of SC-FDE iterative receivers implementing efficient estimation and tracking techniques. The performance results show that the proposed receivers have very good performance, even in the presence of significant Doppler spread between the different groups of multipath components.

Comprehensive comparison of a current-source and a voltage-source converter for three-phase EV fast battery chargers

This paper presents a comprehensive comparison of a current-source converter and a voltage-source converter for three-phase electric vehicle (EV) fast battery chargers. Taking into account that the current-source converter (CSC) is a natural buck-type converter, the output voltage can assume a wide range of values, which varies between zero and the maximum instantaneous value of the power grid phase-to-phase voltage. On the other hand, taking into account that the voltage-source converter (VSC) is a natural boost-type converter, the output voltage is always greater than the maximum instantaneous value of the power grid phase-to-phase voltage, and consequently, it is necessary to use a dc-dc buck-type converter for applications as EV fast battery chargers. Along the paper is described in detail the principle of operation of both the CSC and the VSC for EV fast chargers, as well as the main equations of the power theory and current control strategies. The comparison between both converters is mainly established in terms of the total harmonic distortion of the grid current and the estimated efficiency for a range of operation between 10 kW and 50 kW.

Planeamento fiscal e reestruturação empresarial: análise dos ordenamentos jurídicos português e brasileiro

Dissertação de mestrado em Direito Tributário e Fiscal

Concurrency detection on finish-to-start activity precedence networks

We explore the finish-to-start precedence relations of project activities used in scheduling problems. From these relations, we devise a method to identify groups of activities that could execute concurrently, i.e. activities in the same group can all execute in parallel. The method derives a new set of relations to describe the concurrency. Then, it is represented by an undirected graph and the maximal cliques problem identifies the groups. We provide a running example with a project from our previous studies in resource constrained project cost minimization together with an example application on the concurrency detection method: the evaluation of the resource stress.