The breaking of axisymmetric slender liquid bridges

Liquids held by surface tension forces can bridge the gap between two solid bodies placed not too far apart from each other. The equilibrium conditions and stability criteria for static, cylindrical liquid bridges are well known. However, the behaviour of an unstable liquid bridge, regarding both its transition toward breaking and the resulting configuration, is a matter for discussion. The dynamical problem of axisymmetric rupture of a long liquid bridge anchored at two equal coaxial disks is treated in this paper through the adoption of one-dimensional theories which are widely used in capillary jet problems

Stabilization of embankments on inclined surfaces by micropiles

Embankments constructed on hillsides can have serious problems of stability, generally created by the action of water com-bined with the inclination of the hillside. In order to increase the stability or correct problems of instability already present, there are various methods that can be used: surface and deep drainage, reinforcements with anchored beams, medium and large diameter piles, etc. Standing out among these systems (for its versatility) is the use of micropiles which ?sew? the embankment to a non-unstable area of the hillside. This paper presents research undertaken by means of a finite element code for studying the effect and stress of the micropiles, comparing the results with real measurements taken in the south of Spain.

A linearization-based system reliability method with application to geotechnical analysis

Los análisis de fiabilidad representan una herramienta adecuada para contemplar las incertidumbres inherentes que existen en los parámetros geotécnicos. En esta Tesis Doctoral se desarrolla una metodología basada en una linealización sencilla, que emplea aproximaciones de primer o segundo orden, para evaluar eficientemente la fiabilidad del sistema en los problemas geotécnicos. En primer lugar, se emplean diferentes métodos para analizar la fiabilidad de dos aspectos propios del diseño de los túneles: la estabilidad del frente y el comportamiento del sostenimiento. Se aplican varias metodologías de fiabilidad — el Método de Fiabilidad de Primer Orden (FORM), el Método de Fiabilidad de Segundo Orden (SORM) y el Muestreo por Importancia (IS). Los resultados muestran que los tipos de distribución y las estructuras de correlación consideradas para todas las variables aleatorias tienen una influencia significativa en los resultados de fiabilidad, lo cual remarca la importancia de una adecuada caracterización de las incertidumbres geotécnicas en las aplicaciones prácticas. Los resultados también muestran que tanto el FORM como el SORM pueden emplearse para estimar la fiabilidad del sostenimiento de un túnel y que el SORM puede mejorar el FORM con un esfuerzo computacional adicional aceptable. Posteriormente, se desarrolla una metodología de linealización para evaluar la fiabilidad del sistema en los problemas geotécnicos. Esta metodología solamente necesita la información proporcionada por el FORM: el vector de índices de fiabilidad de las funciones de estado límite (LSFs) que componen el sistema y su matriz de correlación. Se analizan dos problemas geotécnicos comunes —la estabilidad de un talud en un suelo estratificado y un túnel circular excavado en roca— para demostrar la sencillez, precisión y eficiencia del procedimiento propuesto. Asimismo, se reflejan las ventajas de la metodología de linealización con respecto a las herramientas computacionales alternativas. Igualmente se muestra que, en el caso de que resulte necesario, se puede emplear el SORM —que aproxima la verdadera LSF mejor que el FORM— para calcular estimaciones más precisas de la fiabilidad del sistema. Finalmente, se presenta una nueva metodología que emplea Algoritmos Genéticos para identificar, de manera precisa, las superficies de deslizamiento representativas (RSSs) de taludes en suelos estratificados, las cuales se emplean posteriormente para estimar la fiabilidad del sistema, empleando la metodología de linealización propuesta. Se adoptan tres taludes en suelos estratificados característicos para demostrar la eficiencia, precisión y robustez del procedimiento propuesto y se discuten las ventajas del mismo con respecto a otros métodos alternativos. Los resultados muestran que la metodología propuesta da estimaciones de fiabilidad que mejoran los resultados previamente publicados, enfatizando la importancia de hallar buenas RSSs —y, especialmente, adecuadas (desde un punto de vista probabilístico) superficies de deslizamiento críticas que podrían ser no-circulares— para obtener estimaciones acertadas de la fiabilidad de taludes en suelos. Reliability analyses provide an adequate tool to consider the inherent uncertainties that exist in geotechnical parameters. This dissertation develops a simple linearization-based approach, that uses first or second order approximations, to efficiently evaluate the system reliability of geotechnical problems. First, reliability methods are employed to analyze the reliability of two tunnel design aspects: face stability and performance of support systems. Several reliability approaches —the first order reliability method (FORM), the second order reliability method (SORM), the response surface method (RSM) and importance sampling (IS)— are employed, with results showing that the assumed distribution types and correlation structures for all random variables have a significant effect on the reliability results. This emphasizes the importance of an adequate characterization of geotechnical uncertainties for practical applications. Results also show that both FORM and SORM can be used to estimate the reliability of tunnel-support systems; and that SORM can outperform FORM with an acceptable additional computational effort. A linearization approach is then developed to evaluate the system reliability of series geotechnical problems. The approach only needs information provided by FORM: the vector of reliability indices of the limit state functions (LSFs) composing the system, and their correlation matrix. Two common geotechnical problems —the stability of a slope in layered soil and a circular tunnel in rock— are employed to demonstrate the simplicity, accuracy and efficiency of the suggested procedure. Advantages of the linearization approach with respect to alternative computational tools are discussed. It is also found that, if necessary, SORM —that approximates the true LSF better than FORM— can be employed to compute better estimations of the system’s reliability. Finally, a new approach using Genetic Algorithms (GAs) is presented to identify the fully specified representative slip surfaces (RSSs) of layered soil slopes, and such RSSs are then employed to estimate the system reliability of slopes, using our proposed linearization approach. Three typical benchmark-slopes with layered soils are adopted to demonstrate the efficiency, accuracy and robustness of the suggested procedure, and advantages of the proposed method with respect to alternative methods are discussed. Results show that the proposed approach provides reliability estimates that improve previously published results, emphasizing the importance of finding good RSSs —and, especially, good (probabilistic) critical slip surfaces that might be non-circular— to obtain good estimations of the reliability of soil slope systems.

Sobre el comportamiento de micropilotes trabajando a flexión y/o cortante en estructuras de tierra

El empleo de los micropilotes en la ingeniería civil ha revolucionado las técnicas de estabilización de terraplenes a media ladera, ya que aunque los pilotes pueden ser la opción más económica, el uso de micropilotes permite llegar a sitios inaccesibles con menor coste de movimientos de tierras, realización de plataformas de trabajo de dimensiones reducidas, maquinaria necesaria es mucho más pequeña, liviana y versátil en su uso, incluyendo la posibilidad de situar la fabricación de morteros o lechadas a distancias de varias decenas de metros del elemento a ejecutar. Sin embargo, realizando una revisión de la documentación técnica que se tiene en el ámbito ingenieril, se comprobó que los sistemas de diseño de algunos casos (micropilotes en terraplenes a media ladera, micropilotes en pantallas verticales, micropilotes como “paraguas” en túneles, etc.) eran bastante deficientes o poco desarrollados. Premisa que permite concluir que el constructor ha ido por delante (como suele ocurrir en ingeniería geotécnica) del cálculo o de su análisis teórico. Del mismo modo se determinó que en su mayoría los micropilotes se utilizan en labores de recalce o como nueva solución de cimentación en condiciones de difícil acceso, casos en los que el diseño de los micropilotes viene definido por cargas axiales, de compresión o de tracción, consideraciones que se contemplan en reglamentaciones como la “Guía para el proyecto y la ejecución de micropilotes en obras de carretera” del Ministerio de Fomento. En los micropilotes utilizados para estabilizar terraplenes a media ladera y micropilotes actuando como muros pantalla, en los que éstos trabajan a esfuerzo cortante y flexión, no se dispone de sistemas de análisis fiables o no se introduce adecuadamente el problema de interacción terreno-micropilote. Además en muchos casos, los parámetros geotécnicos que se utilizan no tienen una base técnico-teórica adecuada por lo que los diseños pueden quedar excesivamente del lado de la seguridad, en la mayoría de los casos, o todo lo contrario. Uno de los objetivos principales de esta investigación es estudiar el comportamiento de los micropilotes que están sometidos a esfuerzos de flexión y cortante, además de otros objetivos de gran importancia que se describen en el apartado correspondiente de esta tesis. Cabe indicar que en este estudio no se ha incluido el caso de micropilotes quasi-horizontales trabajando a flexion (como los “paraguas” en túneles), por considerarse que estos tienen un comportamiento y un cálculo diferente, que está fuera del alcance de esta investigación. Se ha profundizado en el estudio del empleo de micropilotes en taludes, presentando casos reales de obras ejecutadas, datos estadísticos, problemas de diseño y ejecución, métodos de cálculo simplificados y modelación teórica en cada caso, efectuada mediante el empleo de elementos finitos con el Código Plaxis 2D. Para llevar a cabo los objetivos que se buscan con esta investigación, se ha iniciado con el desarrollo del “Estado del Arte” que ha permitido establecer tipología, aplicaciones, características y cálculo de los micropilotes que se emplean habitualmente. Seguidamente y a efectos de estudiar el problema dentro de un marco geotécnico real, se ha seleccionado una zona española de actuación, siendo ésta Andalucía, en la que se ha utilizado de manera muy importante la técnica de micropilotes sobre todo en problemas de estabilidad de terraplenes a media ladera. A partir de ahí, se ha realizado un estudio de las propiedades geotécnicas de los materiales (principalmente suelos y rocas muy blandas) que están presentes en esta zona geográfica, estudio que ha sido principalmente bibliográfico o a partir de la experiencia en la zona del Director de esta tesis. Del análisis realizado se han establecido ordenes de magnitud de los parámetros geotécnicos, principalmente la cohesión y el ángulo de rozamiento interno (además del módulo de deformación aparente o de un módulo de reacción lateral equivalente) para los diversos terrenos andaluces. Con el objeto de conocer el efecto de la ejecución de un micropilote en el terreno (volumen medio real del micropilote, una vez ejecutado; efecto de la presión aplicada en las propiedades del suelo circundante, etc.) se ha realizado una encuesta entre diversas empresas españolas especializadas en la técnica de los micropilotes, a efectos de controlar los volúmenes de inyección y las presiones aplicadas, en función de la deformabilidad del terreno circundante a dichos micropilotes, con lo que se ha logrado definir una rigidez a flexión equivalente de los mismos y la definición y características de una corona de terreno “mejorado” lograda mediante la introducción de la lechada y el efecto de la presión alrededor del micropilote. Con las premisas anteriores y a partir de los parámetros geotécnicos determinados para los terrenos andaluces, se ha procedido a estudiar la estabilidad de terraplenes apoyados sobre taludes a media ladera, mediante el uso de elementos finitos con el Código Plaxis 2D. En el capítulo 5. “Simulación del comportamiento de micropilotes estabilizando terraplenes”, se han desarrollado diversas simulaciones. Para empezar se simplificó el problema simulando casos similares a algunos reales en los que se conocía que los terraplenes habían llegado hasta su situación límite (de los que se disponía información de movimientos medidos con inclinómetros), a partir de ahí se inició la simulación de la inestabilidad para establecer el valor de los parámetros de resistencia al corte del terreno (mediante un análisis retrospectivo – back-análisis) comprobando a su vez que estos valores eran similares a los deducidos del estudio bibliográfico. Seguidamente se han introducido los micropilotes en el borde de la carretera y se ha analizado el comportamiento de éstos y del talud del terraplén (una vez construidos los micropilotes), con el objeto de establecer las bases para su diseño. De este modo y adoptando los distintos parámetros geotécnicos establecidos para los terrenos andaluces, se simularon tres casos reales (en Granada, Málaga y Ceuta), comparando los resultados de dichas simulaciones numéricas con los resultados de medidas reales de campo (desplazamientos del terreno, medidos con inclinómetros), obteniéndose una reproducción bastante acorde a los movimientos registrados. Con las primeras simulaciones se concluye que al instalar los micropilotes la zona más insegura de la ladera es la de aguas abajo. La superficie de rotura ya no afecta a la calzada que protegen los micropilotes. De ahí que se deduzca que esta solución sea válida y se haya aplicado masivamente en Andalucía. En esas condiciones, podría decirse que no se está simulando adecuadamente el trabajo de flexión de los micropilotes (en la superficie de rotura, ya que no les corta), aunque se utilicen elementos viga. Por esta razón se ha realizado otra simulación, basada en las siguientes hipótesis: − Se desprecia totalmente la masa potencialmente deslizante, es decir, la que está por delante de la fila exterior de micros. − La estratigrafía del terreno es similar a la considerada en las primeras simulaciones. − La barrera de micropilotes está constituida por dos elementos inclinados (uno hacia dentro del terraplén y otro hacia fuera), con inclinación 1(H):3(V). − Se puede introducir la rigidez del encepado. − Los micros están separados 0,556 m ó 1,00 m dentro de la misma alineación. − El empotramiento de los micropilotes en el sustrato resistente puede ser entre 1,5 y 7,0 m. Al “anular” el terreno que está por delante de los micropilotes, a lo largo del talud, estos elementos empiezan claramente a trabajar, pudiendo deducirse los esfuerzos de cortante y de flexión que puedan actuar sobre ellos (cota superior pero prácticamente muy cerca de la solución real). En esta nueva modelación se ha considerado tanto la rigidez equivalente (coeficiente ϴ) como la corona de terreno tratado concéntrico al micropilote. De acuerdo a esto último, y gracias a la comparación de estas modelaciones con valores reales de movimientos en laderas instrumentadas con problemas de estabilidad, se ha verificado que existe una similitud bastante importante entre los valores teóricos obtenidos y los medidos en campo, en relación al comportamiento de los micropilotes ejecutados en terraplenes a media ladera. Finalmente para completar el análisis de los micropilotes trabajando a flexión, se ha estudiado el caso de micropilotes dispuestos verticalmente, trabajando como pantallas discontinuas provistas de anclajes, aplicado a un caso real en la ciudad de Granada, en la obra “Hospital de Nuestra Señora de la Salud”. Para su análisis se utilizó el código numérico CYPE, basado en que la reacción del terreno se simula con muelles de rigidez Kh o “módulo de balasto” horizontal, introduciendo en la modelación como variables: a) Las diferentes medidas obtenidas en campo; b) El espesor de terreno cuaternario, que por lo que se pudo determinar, era variable, c) La rigidez y tensión inicial de los anclajes. d) La rigidez del terreno a través de valores relativos de Kh, recopilados en el estudio de los suelos de Andalucía, concretamente en la zona de Granada. Dicha pantalla se instrumentó con 4 inclinómetros (introducidos en los tubos de armadura de cuatro micropilotes), a efectos de controlar los desplazamientos horizontales del muro de contención durante las excavaciones pertinentes, a efectos de comprobar la seguridad del conjunto. A partir del modelo de cálculo desarrollado, se ha comprobado que el valor de Kh pierde importancia debido al gran número de niveles de anclajes, en lo concerniente a las deformaciones horizontales de la pantalla. Por otro lado, los momentos flectores son bastante sensibles a la distancia entre anclajes, al valor de la tensión inicial de los mismos y al valor de Kh. Dicho modelo también ha permitido reproducir de manera fiable los valores de desplazamientos medidos en campo y deducir los parámetros de deformabilidad del terreno, Kh, con valores del orden de la mitad de los medidos en el Metro Ligero de Granada, pero visiblemente superiores a los deducibles de ábacos que permiten obtener Kh para suelos granulares con poca cohesión (gravas y cuaternario superior de Sevilla) como es el caso del ábaco de Arozamena, debido, a nuestro juicio, a la cementación de los materiales presentes en Granada. En definitiva, de las anteriores deducciones se podría pensar en la optimización del diseño de los micropilotes en las obras que se prevean ejecutar en Granada, con similares características al caso de la pantalla vertical arriostrada mediante varios niveles de anclajes y en las que los materiales de emplazamiento tengan un comportamiento geotécnico similar a los estudiados, con el consiguiente ahorro económico. Con todo ello, se considera que se ha hecho una importante aportación para el diseño de futuras obras de micropilotes, trabajando a flexión y cortante, en obras de estabilización de laderas o de excavaciones. Using micropiles in civil engineering has transformed the techniques of stabilization of embankments on the natural or artificial slopes, because although the piles may be the cheapest option, the use of micropiles can reach inaccessible places with lower cost of earthworks, carrying out small work platforms. Machinery used is smaller, lightweight and versatile, including the possibility of manufacturing mortars or cement grouts over distances of several tens of meters of the element to build. However, making a review of the technical documentation available in the engineering field, it was found that systems designed in some cases (micropiles in embankments on the natural slopes, micropiles in vertical cut-off walls, micropiles like "umbrella" in tunnels, etc.) were quite poor or underdeveloped. Premise that concludes the builder has gone ahead (as usually happen in geotechnical engineering) of calculation or theoretical analysis. In the same way it was determined that most of the micropiles are used in underpinning works or as a new foundation solution in conditions of difficult access, in which case the design of micropiles is defined by axial, compressive or tensile loads, considered in regulations as the " Handbook for the design and execution of micropiles in road construction" of the Ministry of Development. The micropiles used to stabilize embankments on the slopes and micropiles act as retaining walls, where they work under shear stress and bending moment, there are not neither reliable systems analysis nor the problem of soil-micropile interaction are properly introduced. Moreover, in many cases, the geotechnical parameters used do not have a proper technical and theoretical basis for what designs may be excessively safe, or the opposite, in most cases. One of the main objectives of this research is to study the behavior of micro piles which are subjected to bending moment and shear stress, as well as other important objectives described in the pertinent section of this thesis. It should be noted that this study has not included the case of quasi-horizontal micropiles working bending moment (as the "umbrella" in tunnels), because it is considered they have a different behavior and calculation, which is outside the scope of this research. It has gone in depth in the study of using micropiles on slopes, presenting real cases of works made, statistics, problems of design and implementation, simplified calculation methods and theoretical modeling in each case, carried out by using FEM (Finite Element Method) Code Plaxis 2D. To accomplish the objectives of this research, It has been started with the development of the "state of the art" which stipulate types, applications, characteristics and calculation of micropiles that are commonly used. In order to study the problem in a real geotechnical field, it has been selected a Spanish zone of action, this being Andalusia, in which it has been used in a very important way, the technique of micropiles especially in embankments stability on natural slopes. From there, it has made a study of the geotechnical properties of the materials (mainly very soft soils and rocks) that are found in this geographical area, which has been mainly a bibliographic study or from the experience in the area of the Director of this thesis. It has been set orders of magnitude of the geotechnical parameters from analyzing made, especially the cohesion and angle of internal friction (also apparent deformation module or a side reaction module equivalent) for various typical Andalusian ground. In order to determine the effect of the implementation of a micropile on the ground (real average volume of micropile once carried out, effect of the pressure applied on the properties of the surrounding soil, etc.) it has conducted a survey among various skilled companies in the technique of micropiles, in order to control injection volumes and pressures applied, depending on the deformability of surrounding terrain such micropiles, whereby it has been possible to define a bending stiffness and the definition and characteristics of a crown land "improved" achieved by introducing the slurry and the effect of the pressure around the micropile. With the previous premises and from the geotechnical parameters determined for the Andalusian terrain, we proceeded to study the stability of embankments resting on batters on the slope, using FEM Code Plaxis 2D. In the fifth chapter "Simulation of the behavior of micropiles stabilizing embankments", there were several different numerical simulations. To begin the problem was simplified simulating similar to some real in which it was known that the embankments had reached their limit situation (for which information of movements measured with inclinometers were available), from there the simulation of instability is initiated to set the value of the shear strength parameters of the ground (by a retrospective analysis or back-analysis) checking these values were similar to those deduced from the bibliographical study Then micropiles have been introduced along the roadside and its behavior was analyzed as well as the slope of embankment (once micropiles were built ), in order to establish the basis for its design. In this way and taking the different geotechnical parameters for the Andalusian terrain, three real cases (in Granada, Malaga and Ceuta) were simulated by comparing the results of these numerical simulations with the results of real field measurements (ground displacements measured with inclinometers), getting quite consistent information according to registered movements. After the first simulations it has been concluded that after installing the micropiles the most insecure area of the natural slope is the downstream. The failure surface no longer affects the road that protects micropiles. Hence it is inferred that this solution is acceptable and it has been massively applied in Andalusia. Under these conditions, one could say that it is not working properly simulating the bending moment of micropiles (on the failure surface, and that does not cut them), although beam elements are used. Therefore another simulation was performed based on the following hypotheses: − The potentially sliding mass is totally neglected, that is, which is ahead of the outer row of micropiles. − Stratigraphy field is similar to the one considered in the first simulations. − Micropiles barrier is constituted by two inclined elements (one inward and one fill out) with inclination 1 (H): 3 (V). − You can enter the stiffness of the pile cap. − The microlies lines are separated 0.556 m or 1.00 m in the same alignment. − The embedding of the micropiles in the tough substrate can be between 1.5 and 7.0 m. To "annul" the ground that is in front of the micro piles, along the slope, these elements clearly start working, efforts can be inferred shear stress and bending moment which may affect them (upper bound but pretty close to the real) solution. In this new modeling it has been considered both equivalent stiffness coefficient (θ) as the treated soil crown concentric to the micropile. According to the latter, and by comparing these values with real modeling movements on field slopes instrumented with stability problems, it was verified that there is quite a significant similarity between the obtained theoretical values and the measured field in relation to the behavior of micropiles executed in embankments along the natural slope. Finally to complete the analysis of micropiles working in bending conditions, we have studied the case of micropiles arranged vertically, working as discontinued cut-off walls including anchors, applied to a real case in the city of Granada, in the play "Hospital of Our Lady of the Health ". CYPE numeric code, based on the reaction of the ground is simulated spring stiffness Kh or "subgrade" horizontal, introduced in modeling was used as variables for analysis: a) The different measurements obtained in field; b) The thickness of quaternary ground, so that could be determined, was variable, c) The stiffness and the prestress of the anchors. d) The stiffness of the ground through relative values of Kh, collected in the study of soils in Andalusia, particularly in the area of Granada. (previously study of the Andalusia soils) This cut-off wall was implemented with 4 inclinometers (introduced in armor tubes four micropiles) in order to control the horizontal displacements of the retaining wall during the relevant excavations, in order to ensure the safety of the whole. From the developed model calculation, it was found that the value of Kh becomes less important because a large number of anchors levels, with regard to the horizontal deformation of the cut-off wall. On the other hand, the bending moments are quite sensitive to the distance between anchors, the initial voltage value thereof and the value of Kh. This model has also been reproduced reliably displacement values measured in the field and deduce parameters terrain deformability, Kh, with values around half the measured Light Rail in Granada, but visibly higher than deductible of abacuses which can obtain Kh for granular soils with low cohesion (upper Quaternary gravels and Sevilla) such as Abacus Arozamena, because, in our view, to cementing materials in Granada. In short, previous deductions you might think on optimizing the design of micropiles in the works that are expected to perform in Granada, with similar characteristics to the case of the vertical cut-off wall braced through several levels of anchors and in which materials location have a geotechnical behavior similar to those studied, with the consequent economic savings. With all this, it is considered that a significant contribution have been made for the design of future works of micropiles, bending moment and shear stress working in slope stabilization works or excavations.

Experimental study of the thermal-energy performance of an insulated vegetal facade under summer conditions in a continental mediterranean climate

The use of vegetal systems in facades affects the reduction of the buildings' energy demand, the attenuation of the urban heat island (UHI) and the filtration of pollutants present in the air. Even so, up to now the knowledge about the effect of this type of systems on the thermal performance of insulated facades is limited. This article presents the results of an experimental study carried out in a vegetal facade located in a continental Mediterranean climate zone. The objective is to study the effect of a vegetal finishing, formed by plants and substrate, on the thermal-energy performance of an insulated facade under summer conditions. To this effect, the thermal data obtained from two full-scale experimental mock-ups of the same dimensions and composition of the enclosure and only different in the south facade's enclosure where one incorporates a vegetation layer are compared and analysed. The results show that, in spite of the high thermal resistance of the enclosure, the effect of the vegetation is very positive, particularly in the warmer hours of the day. Therefore, vegetal facades can be used as a passive cooling strategy, reducing the consumption of energy for refrigeration and improving the comfort conditions of the users. (C) 2014 Elsevier Ltd. All rights reserved.

Stability analysis of a free falling pararotor

The pararotor is a decelerator device based on the autorotation of a rotating wing. When it is dropped, it generates an aerodynamic force parallel to the main motion direction, acting as a decelerating force. In this paper, the rotational motion equations are shown for the vertical flight without any lateral wind component and some simplifying assumptions are introduced to obtain analytic solutions of the motion. First, the equilibrium state is obtained as a function of the main parameters. Then the equilibrium stability is analyzed. The motion stability depends on two nondimensional parameters, which contain geometric, inertia, and aerodynamic characteristics of the device. Based on these two parameters a stability diagram can be defined. Some stability regions with different types of stability trajectories (nodes, spirals, focuses) can be identified for spinning motion around axes close to the major, minor, and intermediate principal axes. It is found that the blades contribute to stability in a case of spin around the intermediate principal inertia axis, which is otherwise unstable. Subsequently, the equations for determining the angles of nutation and spin of the body are obtained, thus defining the orientation of the body for a stationary motion and the parameters on which that position depends.

Methodology for Dynamic Stability and Robustness Analysis of Commercial-Power-Module-Based DC-Distributed Systems

El propósito de esta tesis es presentar una metodología para realizar análisis de la dinámica en pequeña señal y el comportamiento de sistemas de alimentación distribuidos de corriente continua (CC), formados por módulos comerciales. Para ello se hace uso de un método sencillo que indica los márgenes de estabilidad menos conservadores posibles mediante un solo número. Este índice es calculado en cada una de las interfaces que componen el sistema y puede usarse para obtener un índice global que indica la estabilidad del sistema global. De esta manera se posibilita la comparación de sistemas de alimentación distribuidos en términos de robustez. La interconexión de convertidores CC-CC entre ellos y con los filtros EMI necesarios puede originar interacciones no deseadas que dan lugar a la degradación del comportamiento de los convertidores, haciendo el sistema más propenso a inestabilidades. Esta diferencia en el comportamiento se debe a interacciones entre las impedancias de los diversos elementos del sistema. En la mayoría de los casos, los sistemas de alimentación distribuida están formados por módulos comerciales cuya estructura interna es desconocida. Por ello los análisis presentados en esta tesis se basan en medidas de la respuesta en frecuencia del convertidor que pueden realizarse desde los terminales de entrada y salida del mismo. Utilizando las medidas de las impedancias de entrada y salida de los elementos del sistema, se puede construir una función de sensibilidad que proporciona los márgenes de estabilidad de las diferentes interfaces. En esta tesis se utiliza el concepto del valor máximo de la función de sensibilidad (MPC por sus siglas en inglés) para indicar los márgenes de estabilidad como un único número. Una vez que la estabilidad de todas las interfaces del sistema se han evaluado individualmente, los índices obtenidos pueden combinarse para obtener un único número con el que comparar la estabilidad de diferentes sistemas. Igualmente se han analizado las posibles interacciones en la entrada y la salida de los convertidores CC-CC, obteniéndose expresiones analíticas con las que describir en detalle los acoplamientos generados en el sistema. Los estudios analíticos realizados se han validado experimentalmente a lo largo de la tesis. El análisis presentado en esta tesis se culmina con la obtención de un índice que condensa los márgenes de estabilidad menos conservativos. También se demuestra que la robustez del sistema está asegurada si las impedancias utilizadas en la función de sensibilidad se obtienen justamente en la entrada o la salida del subsistema que está siendo analizado. Por otra parte, la tesis presenta un conjunto de parámetros internos asimilados a impedancias, junto con sus expresiones analíticas, que permiten una explicación detallada de las interacciones en el sistema. Dichas expresiones analíticas pueden obtenerse bien mediante las funciones de transferencia analíticas si se conoce la estructura interna, o utilizando medidas en frecuencia o identificación de las mismas a través de la respuesta temporal del convertidor. De acuerdo a las metodologías presentadas en esta tesis se puede predecir la estabilidad y el comportamiento de sistemas compuestos básicamente por convertidores CC-CC y filtros, cuya estructura interna es desconocida. La predicción se basa en un índice que condensa la información de los márgenes de estabilidad y que permite la obtención de un indicador de la estabilidad global de todo el sistema, permitiendo la comparación de la estabilidad de diferentes arquitecturas de sistemas de alimentación distribuidos. ABSTRACT The purpose of this thesis is to present dynamic small-signal stability and performance analysis methodology for dc-distributed systems consisting of commercial power modules. Furthermore, the objective is to introduce simple method to state the least conservative margins for robust stability as a single number. In addition, an index characterizing the overall system stability is obtained, based on which different dc-distributed systems can be compared in terms of robustness. The interconnected systems are prone to impedance-based interactions which might lead to transient-performance degradation or even instability. These systems typically are constructed using commercial converters with unknown internal structure. Therefore, the analysis presented throughout this thesis is based on frequency responses measurable from the input and output terminals. The stability margins are stated utilizing a concept of maximum peak criteria, derived from the behavior of impedance-based sensitivity function that provides a single number to state robust stability. Using this concept, the stability information at every system interface is combined to a meaningful number to state the average robustness of the system. In addition, theoretical formulas are extracted to assess source and load side interactions in order to describe detailed couplings within the system. The presented theoretical analysis methodologies are experimentally validated throughout the thesis. In this thesis, according to the presented analysis, the least conservative stability margins are provided as a single number guaranteeing robustness. It is also shown that within the interconnected system the robust stability is ensured only if the impedance-based minor-loop gain is determined at the very input or output of each subsystem. Moreover, a complete set of impedance-type internal parameters as well as the formulas according to which the interaction sensitivity can be fully explained and analyzed, is provided. The given formulation can be utilized equally either based on measured frequency responses, time-domain identified internal parameters or extracted analytic transfer functions. Based on the analysis methodologies presented in this thesis, the stability and performance of interconnected systems consisting of converters with unknown internal structure, can be predicted. Moreover, the provided concept to assess the least conservative stability margins enables to obtain an index to state the overall robust stability of distributed power architecture and thus to compare different systems in terms of stability.

Stability and dynamics in a hyperthermophilic protein with melting temperature close to 200°C

The rubredoxin protein from the hyperthermophilic archaebacterium Pyrococcus furiosus was examined by a hydrogen exchange method. Even though the protein does not exhibit reversible thermal unfolding, one can determine its stability parameters—free energy, enthalpy, entropy, and melting temperature—and also the distribution of stability throughout the protein, by using hydrogen exchange to measure the reversible cycling of the protein between native and unfolded states that occurs even under native conditions.

Use of spacecraft data to derive regions on Mars where liquid water would be stable

Combining Viking pressure and temperature data with Mars Orbital Laser Altimeter topography data, we have computed the fraction of the martian year during which pressure and temperature allow for liquid water to be stable on the martian surface. We find that liquid water would be stable within the Hellas and Argyre basin and over the northern lowlands equatorward of about 40°. The location with the maximum period of stable conditions for liquid water is in the southeastern portion of Utopia Planitia, where 34% of the year liquid water would be stable if it were present. Locations of stability appear to correlate with the distribution of valley networks.

Predicted highly expressed and putative alien genes of Deinococcus radiodurans and implications for resistance to ionizing radiation damage

Predicted highly expressed (PHX) and putative alien genes determined by codon usages are characterized in the genome of Deinococcus radiodurans (strain R1). Deinococcus radiodurans (DEIRA) can survive very high doses of ionizing radiation that are lethal to virtually all other organisms. It has been argued that DEIRA is endowed with enhanced repair systems that provide protection and stability. However, predicted expression levels of DNA repair proteins with the exception of RecA tend to be low and do not distinguish DEIRA from other prokaryotes. In this paper, the capability of DEIRA to resist extreme doses of ionizing and UV radiation is attributed to an unusually high number of PHX chaperone/degradation, protease, and detoxification genes. Explicitly, compared with all current complete prokaryotic genomes, DEIRA contains the greatest number of PHX detoxification and protease proteins. Other sources of environmental protection against severe conditions of UV radiation, desiccation, and thermal effects for DEIRA are the several S-layer (surface structure) PHX proteins. The top PHX gene of DEIRA is the multifunctional tricarboxylic acid (TCA) gene aconitase, which, apart from its role in respiration, also alerts the cell to oxidative damage.

Types of evolutionary stability and the problem of cooperation.

The evolutionary stability of cooperation is a problem of fundamental importance for the biological and social sciences. Different claims have been made about this issue: whereas Axelrod and Hamilton's [Axelrod, R. & Hamilton, W. (1981) Science 211, 1390-1398] widely recognized conclusion is that cooperative rules such as "tit for tat" are evolutionarily stable strategies in the iterated prisoner's dilemma (IPD), Boyd and Lorberbaum [Boyd, R. & Lorberbaum, J. (1987) Nature (London) 327, 58-59] have claimed that no pure strategy is evolutionarily stable in this game. Here we explain why these claims are not contradictory by showing in what sense strategies in the IPD can and cannot be stable and by creating a conceptual framework that yields the type of evolutionary stability attainable in the IPD and in repeated games in general. Having established the relevant concept of stability, we report theorems on some basic properties of strategies that are stable in this sense. We first show that the IPD has "too many" such strategies, so that being stable does not discriminate among behavioral rules. Stable strategies differ, however, on a property that is crucial for their evolutionary survival--the size of the invasion they can resist. This property can be interpreted as a strategy's evolutionary robustness. Conditionally cooperative strategies such as tit for tat are the most robust. Cooperative behavior supported by these strategies is the most robust evolutionary equilibrium: the easiest to attain, and the hardest to disrupt.

Diseño de un modelo geológico-geotécnico 3D de la Vega Baja del Río Segura (Alicante, SE España)

Los modelos geológico-geotécnicos permiten al ingeniero comprender mejor las condiciones reinantes en un determinado lugar, además de identificar los principales problemas geotécnicos y hacer más realista la estimación de propiedades del suelo. En este trabajo se presenta la metodología empleada para el diseño de un modelo geológico-geotécnico tridimensional de la Vega Baja del Río Segura que consta de cuatro zonas caracterizadas por sus propiedades geotécnicas y su problemática asociada. El modelo resulta fundamentalmente de gran utilidad para la planificación de investigaciones preliminares de obras civiles.

Hydrogen Production by Steam Reforming of Ethanol on Rh-Pt Catalysts: Influence of CeO2, ZrO2, and La2O3 as Supports

CeO2-, ZrO2-, and La2O3-supported Rh-Pt catalysts were tested to assess their ability to catalyze the steam reforming of ethanol (SRE) for H2 production. SRE activity tests were performed using EtOH:H2O:N2 (molar ratio 1:3:51) at a gaseous space velocity of 70,600 h−1 between 400 and 700 °C at atmospheric pressure. The SRE stability of the catalysts was tested at 700 °C for 27 h time on stream under the same conditions. RhPt/CeO2, which showed the best performance in the stability test, also produced the highest H2 yield above 600 °C, followed by RhPt/La2O3 and RhPt/ZrO2. The fresh and aged catalysts were characterized by TEM, XPS, and TGA. The higher H2 selectivity of RhPt/CeO2 was ascribed to the formation of small (~5 nm) and stable particles probably consistent of Rh-Pt alloys with a Pt surface enrichment. Both metals were oxidized and acted as an almost constant active phase during the stability test owing to strong metal-support interactions, as well as the superior oxygen mobility of the support. The TGA results confirmed the absence of carbonaceous residues in all the aged catalysts.

Does All Fit One Size? An evaluation of the ECB policy response to changing economic conditions in the Euro area member states. ACES Cases No. 2008.1

This paper empirically investigates the extent to which the European Central Bank has responded to evolving economic conditions in its member states as opposed to the euro area as a whole. Based on a forward-looking Taylor rule-type policy reaction function, we conduct counterfactual exercises that compare the monetary policy behavior of the ECB with two alternative hypothetical scenarios: (1) were the euro member states to make individual policy decisions, and (2) were the ECB to respond to the economic conditions of individual members. The results reflect the extent of heterogeneity among the national economies in the monetary union and indicate that the ECB's monetary policy rates have been particularly close to the "counterfactual" interest rates of its largest euro members, as well as of countries with similar economic conditions, which includes Germany, Austria, Belgium and France.