Fruit processing, seed viability and dormancy mechanisms of Persoonia sericea A. Cunn. ex R. Br. and P-virgata R. Br. (Proteaceae)

The morphology of the fruit and difficulties with fruit processing impose major limitations to germination of Persoonia sericea and P. virgata. The mesocarp must be removed without harming the embryo. Fermentation of fruit or manual removal of the mesocarp was effective but digestion in 32% hydrochloric acid (HCl) completely inhibited germination. The endocarp is extremely hard and therefore very difficult and time consuming to remove without damaging the seeds. The most efficient method was cracking the endocarp with pliers, followed by manual removal of seeds. Germination was completely inhibited unless at least half of the endocarp was removed. Microbial contamination of the fruit and seeds was controlled by disinfestation and germination of the seed under aseptic conditions. The results suggest that dormancy in these species is primarily due to physical restriction of the embryo by the hard endocarp.

Rheological Properties of Organoclay Suspensions in Epoxy Network Precursors

This paper deals with the evolution of the state of dispersion of organically modified montmorillonites in epoxy or amine precursors. The epoxy prepolymer is a diglycidyl ether of bisphenol A (DGEBA) and the curing agent is an aliphatic diamine with a polyoxypropylene backbone (Jeffamine D2000). The clay dispersion is evaluated at the platelet scale (nanoscopic scale) from X-ray spectrometry [wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS)] and at the aggregates scale (microscopic scale) from rheological analysis. The organoclays used form gels in the monomers above the percolation threshold if no shear is applied and present a mechanical gel/sol transition when shear stress increases. Gel strength and viscosity at high shear rates are linked to the nanometric state of dispersion and reveal the existence of two different organizations depending on organoclay/monomer interactions: (i) When the clay shows good interactions with the monomer, a significant swelling of the clay galleries by the monomer is obtained. These swollen particles lead to formation of weak gels which after shearing give high relative viscosity fluids. (ii) When the clay develops poor interactions with the monomer, the clay tends to reduce its exchange surface with the monomer and leads to a strongly connected gel. Shear breaks down this physical network leading to a very low relative viscosity fluid composed of nonswollen particles keeping a high aspect ratio. (C) 2003 Elsevier B.V All rights reserved.

Age hardening of a sintered Al-Cu-Mg-Si-(Sn) alloy

The age hardening response of a sintered Al-3.8 wt% Cu-1.0 wt% Mg-0.70 wt% Si alloy with and without 0.1 wt% Sn was investigated. The sequence of precipitation was characterised using transmission electron microscopy. The ageing response of the sintered Al-Cu-Mg-Si-(Sn) alloy is similar to that of cognate wrought 2xxx series alloys. Peak hardness was associated with a fine, uniform dispersion of lath shaped precipitates, believed to be either the betaor Q phase, oriented along < 010 >. directions and theta' plates lying on {001}(alpha). planes. Natural ageing also resulted in comparable behaviour to that observed in wrought alloys. Porosity in the powder metallurgy alloys did not significantly affect the kinetics of precipitation during artificial ageing. Trace levels of tin, used to aid sintering, slightly reduced the hardening response of the alloy. However, this was compensated for by significant improvements in density and hardness. (c) 2005 Elsevier B.V. All rights reserved.

Encapsulation of lipopeptides within liposomes: Effect of number of lipid chains, chain length and method of liposome preparation

The purpose of this study was to systematically investigate the effect of lipid chain length and number of lipid chains present on lipopeptides on their ability to be incorporated within liposomes. The peptide KAVYNFATM was synthesized and conjugated to lipoamino acids having acyl chain lengths of C-8, C-12 and C-16. The C-12 construct was also prepared in the monomeric, dimeric and trimeric form. Liposomes were prepared by two techniques: hydration of dried lipid films (Bangham method) and hydration of freeze-dried monophase systems. Encapsulation of lipopeptide within liposomes prepared by hydration of dried lipid films was incomplete in all cases ranging from an entrapment efficiency of 70% for monomeric lipoamino acids at a 5% (w/w) loading to less than 20% for di- and trimeric forms at loadings of 20% (w/w). The incomplete entrapment of lipopeptides within liposomes appeared to be a result of the different solubilities of the lipopeptide and the phospholipids in the solvent used for the preparation of the lipid film. In contrast, encapsulation of lipopeptide within liposomes prepared by hydration of freeze-dried monophase systems was high, even up to a loading of 20% (w/w) and was much less affected by the acyl chain length and number than when liposomes were prepared by hydration of dried lipid films. Freeze drying of monophase systems is better at maintaining a molecular dispersion of the lipopeptide within the solid phospholipid matrix compared to preparation of lipid film by evaporation, particularly if the solubility of the lipopeptide in solvents is markedly different from that of the polar lipids used for liposome preparation. Consequently, upon hydration, the lipopeptide is more efficiently intercalated within the phospholipid bilayers. (C) 2005 Elsevier B.V. All rights reserved.

Burial depth and cultivation influence emergence and persistence of Phalaris paradoxa seed in an Australian sub-tropical environment

Emergence and persistence characteristics of Phalaris paradoxa seeds in no- and minimum-till situations and at different burial depths were studied in a sub-tropical environment. Three experiments were carried out using naturally shed seeds. In the first experiment, seedlings emerged from May through to September each year, although the majority of seedlings emerged in July. In the second experiment with greater seed density, cultivation in March of each year stimulated seedling emergence, altered the periodicity of emergence and accelerated the decline of seeds in the seedbank compared with plots that received no cultivation. The majority of seedlings in the cultivated plots emerged in May whereas the majority of seedlings in the undisturbed plots emerged in July. Emergence accounted for only 4-19% of the seedbank in both experiments over 2 years. Seed persistence was short in both field experiments, with less than 1% remaining 2 years after seed shed. In the third experiment, burial depth and soil disturbance significantly influenced seedling emergence and persistence of seed. Seedlings emerged most from seed mixed in the top 10 cm when subjected to annual soil disturbance, and from seed buried at 2.5 and 5.0 cm depths in undisturbed soil. Emergence was least from seed on the soil surface, and buried at 10 and 15 cm depths in undisturbed soil. Seeds persisted longest when shed onto the soil surface and persisted least when the soil was tilled. These results suggest that strategic cultivation may be a useful management tool, as it will alter the periodicity of emergence allowing use of more effective control options and will deplete the soil seedbank more rapidly.

Climatic regulation of seed dormancy and emergence of diverse Malva parviflora populations from a Mediterranean-type environment

Malva parviflora L. (Malvaceae) is rapidly becoming a serious weed of Australian farming systems. An understanding of the variability of its seed behaviour is required to enable the development of integrated weed management strategies. Mature M. parviflora seeds were collected from four diverse locations in the Mediterranean-type climatic agricultural region of Western Australia. All of the seeds exhibited physical dormancy at collection; manual scarification or a period of fluctuating summer temperatures (50/20 degrees C or natural) were required to release dormancy. When scarified and germinated soon (1 month) after collection, the majority of seeds were able to germinate over a wide range of temperatures (5-37 degrees C) and had no light requirement. Germination was slower for seeds stored for 2 months than seeds stored for 2 years, suggesting the presence of shallow physiological dormancy. Seed populations from regions with similar annual rainfall exhibited similar dormancy release patterns; seeds from areas of low rainfall (337-344mm) were more responsive to fluctuating temperatures, releasing physical dormancy earlier than those from areas of high rainfall (436-444mm). After 36 months, maximum seedling emergence from soil in the field was 60%, with buried seeds producing 13-34% greater emergence than seeds on the surface. Scanning electron microscopy of the seed coat revealed structural differences in the chalazal region of permeable and impermeable seeds, suggesting the importance of this region in physical dormancy breakdown of M. parviflora seeds. The influence of rainfall during plant growth in determining dormancy release, and hence, germination and emergence timing, must be considered when developing management strategies for M. parviflora.

The graying of R&D workgroups: The effects of age diversity on developing publicly usable knowledge

Does the graying of scientific research teams matter? This study addresses how workgroup processes and external environmental factors contribute and inhibit the effect of age diversity in R&D project groups on the production of innovative publicly usable knowledge outcomes in the form of publication outputs. We examined the relationships between group age diversity (age cohort diversity, mean age, age dispersion), R&D workgroup member self-ratings of workgroup processes, their supervisor�s assessment of the external environmental factors the project groups faced, and their supervisor�s ratings of group performance, the number of scientific publicly available publications produced by the group and the use of multiple authorships on publications. Usable data was obtained from 32 R&D workgroups of a large Government Agricultural Research and Development Agency. Consistent with the literature, workgroup processes and external environmental factors were found to directly effect innovation outcomes. Contrary to expectation, but consistent with Social Identity theory, workgroup age diversity generally negatively impacted upon innovation outcomes. An exception was where multiple authorship on publications for project groups increased as the dispersion of age within groups increased. Importantly, workgroups that were both more age homogeneous and perceived to have optimally functioning work processes produced more R&D innovation outcomes than other groups. Generally, these differences appear to be related to the greater division of labor practices (and less multi-tasking) employed by the older and more homogeneous workgroups. Implications for R&D workgroup resource theory and practices are discussed.

40Ar/39Ar dating of Mn-iron ore of the Sapecado Mine, Qadrilatero Ferrifero, Brazil

The SW region of Amazonian craton presents policyclic evolution between 1.80-1.00 Ga and is comprised of the Rio Negro-Juruena, Rondoniana and Sunsas Provinces. The evolution of this region has being characterized by four orogens: Alto Jauru (1.79-1.74 Ga), Cachoeirinha (1.58-1.52 Ga), Suíte Santa Helena (1.45-1.42 Ga) e Sunsas/Aguapeí (1.0-0.9 Ga). The Alto Jauru orogen consists of TTG gneissic associations, greenstone sequences and intrusive granitoids origined in volcanic arc setting. Eight 40Ar/39Ar step-heating analyses were carried out in minerals (biotiteand hornblende) to investigate the thermal history and crustal evolution of this region. From the Alto Jauru orogen was sampled the gneiss banded and two biotite grains provide large dispersion of apparent ages, suggesting heterogenity in reservoir of the argon. Apparent age diagram yielded integrated ages of 1472 ± 6 Ma, interpreted as minimum ages of regional cooling episode. Three analyses of hornblende present ages varing from 1310 to 1400 Ma, possibly because smaller grain size become more susceptible to argon loss. 40Ar/39Ar step-heating methodology applied on biotite of pyroclastic tuff (U-Pb age about 1758 ± 7 Ma) presented integrated age of 1507 ± 7 Ma. The results found for this terrane demonstrated a geochronological correlation with metamorphic process linked Cachoeirinha orogen. Biotite and hornblende grains separates from granite and a tonalite origined during Cachoeirinha orogen were analyzed and the apparent age diagrams indicated well-defined plateau ages of 1520-1540 Ma. Biotite grains from a granitic sample were analized, and integrated ages about 1526 ± 2 Ma were obtained due argon loss in the initial steps. Thermochronologic history of SW region Amazonian craton is coherent with regional policyclic events and 40Ar/39Ar ages here presented probably correspond to regional cooling period of Cachoeirinha orogen.

Study of the effects of climate warming on seed germination and seed longevity of snowbed species

Understanding how climate change will affect the distribution and the phenology of plants is becoming an increasingly important topic in ecological studies. In response to climate warming, there are documented upward shift and alterations of phenology and physiology of several plant species. Despite this, the effects of climate change on plant regeneration from seeds have largely been neglected. However, regeneration from seeds, a key event in the plant life cycle, could be significantly affected by climate warming. In this regard, we investigated how climatic changes will affect the seasonal dynamics of seed germination and seedling survival in two different alpine context. The first part refers to five species inhabiting a snowbed located at the Gavia pass (Parco Naturale dello Stelvio). Here, plants were exposed, in the field, to natural conditions and to artificial warming using Open Top Chambers proposed by the ITEX (International Tundra Experiment). The germination curves of seeds produced were compared in order to highlight differences in seed germination ecology and in seed physiology induced by the climate warming. In the second part, we considered two tree species that form the treeline in Davos (Switzerland). As a surrogate of climate warming we used the natural thermal gradient driven by the altitude and we compared the germination behavior of the species studied in three sites at three different elevations in order to evaluate the likelihood of treeline shift under the predicted climate warming.

Constructing an 'efficient frontier' of accounting journal quality

This paper reports the construction of an 'efficient frontier' of the perceived quality attributes of academic accounting journals. The analysis is based on perception data from two web-based surveys of Australasian and British academics. The research reported here contributes to the existing literature by augmenting the commonly supported single dimension of quality with an additional measure indicating the variation of perceptions of journal quality. The result of combining these factors is depicted diagrammatically in a manner that reflects the risk and return trade-off as conceptualised in the capital market model of an efficient frontier of investment opportunities. This conceptualisation of a 'market' for accounting research provides a context in which to highlight the complex issues facing academics in their roles as editors, researchers and authors. The analysis indicates that the perceptions of the so-called 'elite' US accounting journals have become unsettled particularly in Australasia, showing high levels of variability in perceived quality, while other traditionally highly ranked journals (ABR, AOS, CAR) have a more 'efficient' combination of high-quality ranking and lower dispersion of perceptions. The implications of these results for accounting academics in the context of what is often seen as a market for accounting research are discussed. © 2006 Elsevier Ltd. All rights reserved.

Experimental and theoretical characterisation of tunable fibre gratings

This thesis presents details on both theoretical and experimental aspects of UV written fibre gratings. The main body of the thesis deals with the design, fabrication and testing of telecommunication optical fibre grating devices, but also an accurate theoretical analysis of intra-core fibre gratings is presented. Since more than a decade, fibre gratings have been extensively used in the telecommunication field (as filters, dispersion compensators, and add/drop multiplexers for instance). Gratings for telecommunication should conform to very high fabrication standards as the presence of any imperfection raises the noise level in the transmission system compromising its ability of transmitting intelligible sequence of bits to the receiver. Strong side lobes suppression and high and sharp reflection profile are then necessary characteristics. A fundamental part of the theoretical and experimental work reported in this thesis is about apodisation. The physical principle of apodisation is introduced and a number of apodisation techniques, experimental results and numerical optimisation of the shading functions and all the practical parameters involved in the fabrication are detailed. The measurement of chromatic dispersion in fibres and FBGs is detailed and an estimation of its accuracy is given. An overview on the possible methods that can be implemented for the fabrication of tunable fibre gratings is given before detailing a new dispersion compensator device based on the action of a distributed strain onto a linearly chirped FBG. It is shown that tuning of second and third order dispersion of the grating can be obtained by the use of a specially designed multipoint bending rig. Experiments on the recompression of optical pulses travelling long distances are detailed for 10 Gb/s and 40 Gb/s. The characterisation of a new kind of double section LPG fabricated on a metal-clad coated fibre is reported. The fabrication of the device is made easier by directly writing the grating through the metal coating. This device may be used to overcome the recoating problems associated with standard LPGs written in step-index fibre. Also, it can be used as a sensor for simultaneous measurements of temperature and surrounding medium refractive index.

Surface wave techniques for the study of engineering structures and materials

A wire drive pulse echo method of measuring the spectrum of solid bodies described. Using an 's' plane representation, a general analysis of the transient response of such solids has been carried out. This was used for the study of the stepped amplitude transient of high order modes of disks and for the case where there are two adjacent resonant frequencies. The techniques developed have been applied to the measurenent of the elasticities of refractory materials at high temperatures. In the experimental study of the high order in-plane resonances of thin disks it was found that the energy travelled at the edge of the disk and this initiated the work on one dimensional Rayleigh waves.Their properties were established for the straight edge condition by following an analysis similar to that of the two dimensional case. Experiments were then carried out on the velocity dispersion of various circuits including the disk and a hole in a large plate - the negative curvature condition.Theoretical analysis established the phase and group velocities for these cases and experimental tests on aluminium and glass gave good agreement with theory. At high frequencies all velocities approach that of the one dimensional Rayleigh waves. When applied to crack detection it was observed that a signal burst travelling round a disk showed an anomalous amplitude effect. In certain cases the signal which travelled the greater distance had the greater amplitude.An experiment was designed to investigate the phenanenon and it was established that the energy travelled in two nodes with different velocities.It was found by analysis that as well as the Rayleigh surface wave on the edge, a seoond node travelling at about the shear velocity was excited and the calculated results gave reasonable agreement with the experiments.

40Gbit/s single channel dispersion managed pulse propagation in standard fibre over 509km

Error free propagation of a single polarisation optical time division multiplexed 40Gbit/s dispersion managed pulse data stream over 509km has been achieved in standard (non-dispersion shifted) fibre. Dispersion compensating fibre was used after each amplifier to reduce the high local dispersion of the standard fibre. © IEE 1999.

Hydrodynamic modeling of mineral wool fiber suspensions in a two-dimensional channel flow

A consequence of a loss of coolant accident is the damage of adjacent insulation materials (IM). IM may then be transported to the containment sump strainers where water is drawn into the ECCS (emergency core cooling system). Blockage of the strainers by IM lead to an increased pressure drop acting on the operating ECCS pumps. IM can also penetrate the strainers, enter the reactor coolant system and then accumulate in the reactor pressure vessel. An experimental and theoretical study that concentrates on mineral wool fiber transport in the containment sump and the ECCS is being performed. The study entails fiber generation and the assessment of fiber transport in single and multi-effect experiments. The experiments include measurement of the terminal settling velocity, the strainer pressure drop, fiber sedimentation and resuspension in a channel flow and jet flow in a rectangular tank. An integrated test facility is also operated to assess the compounded effects. Each experimental facility is used to provide data for the validation of equivalent computational fluid dynamic models. The channel flow facility allows the determination of the steady state distribution of the fibers at different flow velocities. The fibers are modeled in the Eulerian-Eulerian reference frame as spherical wetted agglomerates. The fiber agglomerate size, density, the relative viscosity of the fluid-fiber mixture and the turbulent dispersion of the fibers all affect the steady state accumulation of fibers at the channel base. In the current simulations, two fiber phases are separately considered. The particle size is kept constant while the density is modified, which affects both the terminal velocity and volume fraction. The relative viscosity is only significant at higher concentrations. The numerical model finds that the fibers accumulate at the channel base even at high velocities; therefore, modifications to the drag and turbulent dispersion forces can be made to reduce fiber accumulation.

Autocatalytic deposition of composite coatings

The deposition and properties of electroless nickel composite coatings containing graphite, PTFE and chromium were investigated. Solutions were developed for the codeposition of graphite and chromium with electroless nickel. Solutions for the deposition of graphite contained heavy metal ions for stability, with non-ionic and anionic surfactants to provide wetting and dispersion of the particles. Stability for the codeposition of chromium particles was achieved by oxidation of the chromium. Thin oxide layers of 200 nm thick prevented initiation of the electroless reaction onto the chromium. A mechanism for the formation of electroless composite coatings was considered based on the physical adsorption of particles and as a function of the adsorption of charged surfactants and metal cations from solution. The influence of variables such as particle concentration in solution, particle size, temperature, pH, and agitation on the volume percentage of particles codeposited was studied. The volume percentage of graphite codeposited was found to increase with concentration in solution and playing rate. An increase in particle size and agitation reduced the volume percentage codeposited. The hardness of nickel-graphite deposits was found to decrease with graphite content in the as-deposited and heat treated condition. The frictional and wear properties of electroless nickel-graphite were studied and compared to those of electroless nickel-PTFE. The self-lubricating nature of both coatings was found to be dependent on the ratio of coated area to uncoated area, the size and content of lubricating material in the deposit, and the load between contacting surfaces. The mechanism of self-lubrication was considered, concluding that graphite only produced an initial lubricating surface due to the orientation of flakes, unlike PTFE, which produced true self-lubrication throughout the coating life. Heat treatment of electroless nickel chromium deposits at 850oC for 8 and 16 hours produced nickel-iron-chromium alloy deposits with a phosphorus rich surface of high hardness. Coefficients of friction and wear rates were intially moderate for the phosphorus rich layer but increased for the nickel-iron-chromium region of the coating.