Ganhos de peso, taxas de deposição e composição química corporal de tourinhos Santa Gertrudes confinados, recebendo alto concentrado e níveis crescentes de polpa cítrica peletizada

Objetivou-se avaliar a substituição do milho em grão pela polpa cítrica peletizada e seus efeitos sobre os ganhos de peso, as taxas de deposição e a composição química corporal de tourinhos Santa Gertrudes em confinamento. Vinte e oito animais (idade média de nove meses e peso inicial de 277 kg) foram mantidos em baias individuais durante 92 dias, após 21 dias de adaptação. Os animais receberam dietas contendo 20% da MS como silagem de milho que continha 40% de grãos. Foram testados os níveis de 0, 25, 40 e 55% de participação da polpa cítrica peletizada na MS da dieta. A composição química corporal foi estimada a partir de equações desenvolvidas para a mesma raça, utilizando-se a composição química do corte da 9-10-11ª costelas. A participação da polpa cítrica peletizada não afetou significativamente o peso corporal final (449 kg) e os ganhos diários de peso corporal (1,50 kg), de corpo vazio (1,26 kg) e de carcaça (0,78 kg). Não houve diferença entre tratamentos para as taxas diárias de deposição de água (0,374 kg), EE (0,589 kg), proteína (0,253 kg), minerais (0,040 kg) e energia (6,934 Mcal) e, conseqüentemente, a composição química corporal final foi similar entre os animais recebendo diferentes níveis de polpa cítrica na dieta. A substituição do milho em grão por polpa cítrica peletizada, até 55% da MS, em dietas para tourinhos em terminação recebendo altos níveis de concentrado, não altera os ganhos de peso, as taxas de deposição e a composição química corporal desses animais.

Evaluation of corn cultivars harvested at two cutting heights for ensilage

Objetivou-se neste estudo avaliar as características agronômicas, a composição químico-bromatológica e a digestibilidade de 11 cultivares de milho (Zea mays) colhido em duas alturas de corte. As cultivares D 766, D 657, D 1000, P 3021, P 3041, C 805, C 333, AG 5011, FO 01, CO 9621 e BR 205 foram avaliadas quando colhidas 5 cm acima do solo (baixa) e 5 cm abaixo da inserção da primeira espiga (alta). O experimento foi delineado como blocos casualizados, com três repetições, arranjados em esquema fatorial 11 x 2. Os cultivares apresentaram produções semelhantes de matéria seca de forragem e de grãos. As porcentagens das frações colmo, folha, palha, sabugo e grão diferiram entre os cultivares, assim como os teores de matéria seca da planta inteira no momento da colheita. Considerando a planta inteira, apenas os teores de energia bruta, nitrogênio da fração fibra em detergente neutro e a digestibilidade in vitro da fibra em detergente neutro e detergente ácido não diferiram entre os cultivares. O aumento da altura de corte melhorou a qualidade da forragem, devido à redução das frações colmo e folha e dos teores dos constituintes da parede celular.

Uso da somatotropina bovina recombinante - rbST como alternativa para a produção de leite de cabra na entressafra

O experimento desenvolveu-se no Setor de Caprinocultura da FMVZ - UNESP - Campus de Botucatu, com o objetivo de estudar a influência da somatotropina bovina recombinante (rbST - nome comercial: Boostin 250 mg) na produção de leite, nos constituintes do leite, peso e escore de condição corporal de cabras durante o ciclo lactacional. Foram usadas 21 cabras da raça Parda Alpina, com idade entre 1 ½ e 4 anos, distribuídas aleatoriamente entre três tratamentos de sete animais cada: controle (T1 - sem rbST); completo, safra e entressafra (T2 - rbST após 45 dias de lactação); e apenas entressafra (T3 - rbST após 154 dias de lactação). Os animais dos três tratamentos receberam a mesma alimentação, que diferiu apenas na quantidade de concentrado, ajustada de acordo com a produção de leite dos animais. Não se observou aumento na produção de leite dos animais tratados, mas a persistência da lactação foi maior nestes animais. Não se observou diferença entre animais controles e tratados quanto aos constituintes do leite (densidade, gordura, EST, lactose e proteína). O peso e o índice de condição corporal também não apresentaram diferença significativa entre animais tratados e controle.

Avaliação de fontes de urease na amonização de fenos de Brachiaria brizantha com dois teores de umidade

O efeito da amonização com uréia (5,0% matéria seca) do feno de Brachiaria brizantha, com dois teores de umidade (15 ou 30% de umidade), associado a três fontes de urease (feno de capim Brachiaria decumbens, capim-elefante [Pennisetum purpureum] e leucena [Leucaena leucocephala]), foi avaliado. Foram determinados os teores de proteína bruta (PB), fração solúvel (A), frações de proteína verdadeira solúvel e insolúvel em borato fosfato (B1 e B2), fração de proteína potencialmente degradável (B3) e fração da proteína insolúvel em detergente ácido (C). Avaliaram-se os teores de fibra em detergente neutro (FDN), fibra em detergente ácido (FDA), celulose (CEL), hemicelulose (HEM) e lignina (LIG) e digestibilidade in vitro da matéria seca (DIVMS). O delineamento experimental foi o de blocos inteiramente casualizados, com 10 tratamentos (dois controles, 15 e 30% umidade, sem uréia e sem urease; dois controles, 15 e 30% umidade, com uréia e sem urease; seis combinações de fontes de urease e conteúdo de umidade) e três repetições. A amonização dos fenos com diferentes conteúdos de umidade, associados a fontes de urease, aumentou os teores de PB e da fração A, mas não afetou B1 e B2. Contudo, as frações B3 e C diminuíram em reposta à amonização. A aplicação de uréia nos fenos de 30% de umidade, associados ou não a fontes de urease, diminuiu os teores de FDN. A adição de fontes de urease não alterou os teores dos constituintes da parede celular, quando comparada aos tratamentos amonizados com uréia. Os tratamentos aplicados não proporcionaram efeitos consistentes sobre os teores de FDA e de CEL dos fenos e não afetaram os teores de LIG. A aplicação de uréia associada a 15 ou 30% de umidade foi favorável para aumentar o nitrogênio solúvel do feno de Brachiaria brizantha e diminuir o nitrogênio indisponível para o ruminante.

Modelo 2,5D de predição de propagação para ambientes interiores utilizando o método do traçado de raios

A 2.5D ray-tracing propagation model is proposed to predict radio loss in indoor environment. Specifically, we opted for the Shooting and Bouncing Rays (SBR) method, together with the Geometrieal Theory of Diffrartion (GTD). Besides the line-of-sight propagation (LOS), we consider that the radio waves may experience reflection, refraction, and diffraction (NLOS). In the Shooting and Bouncing Rays (SBR) method, the transmitter antenna launches a bundle of rays that may or may not reach the receiver. Considering the transmitting antenna as a point, the rays will start to launch from this position and can reach the receiver either directly or after reflections, refractions, diffractions, or even after any combination of the previous effects. To model the environment, a database is built to record geometrical characteristics and information on the constituent materials of the scenario. The database works independently of the simulation program, allowing robustness and flexibility to model other seenarios. Each propagation mechanism is treated separately. In line-of-sight propagation, the main contribution to the received signal comes from the direct ray, while reflected, refracted, and diffracted signal dominate when the line-of-sight is blocked. For this case, the transmitted signal reaches the receiver through more than one path, resulting in a multipath fading. The transmitting channel of a mobile system is simulated by moving either the transmitter or the receiver around the environment. The validity of the method is verified through simulations and measurements. The computed path losses are compared with the measured values at 1.8 GHz ftequency. The results were obtained for the main corridor and room classes adjacent to it. A reasonable agreement is observed. The numerical predictions are also compared with published data at 900 MHz and 2.44 GHz frequencies showing good convergence

Desenvolvimento e projeto de colhedora de babaçu (Orbignya phalerata Mart.) para agricultura familiar nas regiões de matas de transição da Amazônia

O babaçu (Orbignya phalerata) é uma típica palmeira das matas de transição dos ecossistemas Amazônia/Cerrado e Amazônia/Caatinga, sendo de grande importância econômica, social e ambiental nestas regiões. Os produtos advindos dos babaçuais possibilitam renda para uma das camadas mais pobres da região amazônica e um dos entraves para a obtenção eficiente destes produtos é a colheita dos cocos de babaçu, que atualmente se faz no sistema extrativista. O objetivo deste trabalho foi realizar o desenvolvimento e projeto de uma colhedora de babaçu adaptável ao ambiente de trabalho da agricultura familiar e as características das matas de transição amazônicas. Para tal foram realizados estudos de literatura que nortearam as decisões e simplificações de projeto, assim como foram realizados os cálculos e desenhos da nova colhedora. O projeto foi realizado através de ferramentas de engenharia que apresentaram como resultados o memorial de cálculo que descreve o caminho técnico para o dimensionamento dos elementos constituintes da colhedora e a partir destes os desenhos detalhados dos elementos da nova máquina. Pelos desenhos detalhados suas considerações e decisões concluí-se que a colhedora de babaçu apresenta-se passível de ser construída com materiais nacionais de baixo custo, além de fácil operação, manutenção e com mínimo efeito sobre os babaçuais naturais.

Sazonalidade dos ductos secretores e óleo essencial de Foeniculum vulgare var. vulgare Mill. (Apiaceae)

Este trabalho teve como objetivo analisar os ductos secretores e o óleo essencial das folhas de Foeniculum vulgare em diferentes épocas do ano. Para esta finalidade, foram realizados estudos de caracterização anatômica, bem como anatomia comparada dos ductos secretores e testes histoquímicos das folhas. O óleo essencial foi obtido de folhas e frutos, por hidrodestilação em aparelho de Clevenger e analisados quantitativamente e qualitativamente por cromatografia em fase gasosa acoplada ao espectrômetro de massa, realizando-se análises seguidas de três réplicas para folhas coletadas durante o inverno e primavera, e frutos no verão. Os resultados encontrados para os ductos secretores de óleo corresponderam à redução do teor de óleo essencial nas folhas coletadas no final da primavera. O componente majoritário do óleo essencial de folhas e frutos foi o trans-anetol, durante todas as estações do ano. Portanto, evidenciou-se que os ductos secretores e teor de óleo essencial estão relacionados, bem como os constituintes químicos também estão sujeitos a sazonalidade, conforme o estágio fenológico da planta.

Arquitetura de Software para Barcos Robóticos

We propose in this work a software architecture for robotic boats intended to act in diverse aquatic environments, fully autonomously, performing telemetry to a base station and getting this mission to be accomplished. This proposal aims to apply within the project N-Boat Lab NatalNet DCA, which aims to empower a sailboat navigating autonomously. The constituent components of this architecture are the memory modules, strategy, communication, sensing, actuation, energy, security and surveillance, making these systems the boat and base station. To validate the simulator was developed in C language and implemented using the graphics API OpenGL resources, whose main results were obtained in the implementation of memory, performance and strategy modules, more specifically data sharing, control of sails and rudder and planning short routes based on an algorithm for navigation, respectively. The experimental results, shown in this study indicate the feasibility of the actual use of the software architecture developed and their application in the area of autonomous mobile robotics

Metodologia de análise e diagnóstico de fratura em um componente automotivo sujeito a cargas cíclicas alternadas

The competitiveness of the trade generated by the higher availability of products with lower quality and cost promoted a new reality of industrial production with small clearances. Track deviations at the production are not discarded, uncertainties can statistically occur. The world consumer and the Brazilian one are supported by the consumer protection code, in lawsuits against the products poor quality. An automobile is composed of various systems and thousands of constituent parts, increasing the likelihood of failure. The dynamic and security systems are critical in relation to the consequences of possible failures. The investigation of the failure gives us the possibility of learning and contributing to various improvements. Our main purpose in this work is to develop a systematic, specific methodology by investigating the root cause of the flaw occurred on an axle end of the front suspension of an automobile, and to perform comparative data analyses between the fractured part and the project information. Our research was based on a flaw generated in an automotive suspension system involved in a mechanical judicial cause, resulting in property and personal damages. In the investigations concerning the analysis of mechanical flaws, knowledge on materials engineering plays a crucial role in the process, since it enables applying techniques for characterizing materials, relating the technical attributes required from a respective part with its structure of manufacturing material, thus providing a greater scientific contribution to the work. The specific methodology developed follows its own flowchart. In the early phase, the data in the records and information on the involved ones were collected. The following laboratory analyses were performed: macrography of the fracture, micrography with SEM (Scanning Electron Microscope) of the initial and final fracture, phase analysis with optical microscopy, Brinell hardness and Vickers microhardness analyses, quantitative and qualitative chemical analysis, by using X-ray fluorescence and optical spectroscopy for carbon analysis, qualitative study on the state of tension was done. Field data were also collected. In the analyses data of the values resulting from the fractured stock parts and the design values were compared. After the investigation, one concluded that: the developed methodology systematized the investigation and enabled crossing data, thus minimizing diagnostic error probability, the morphology of the fracture indicates failure by the fatigue mechanism in a geometrically propitious location, a tension hub, the part was subjected to low tensions by the sectional area of the final fracture, the manufacturing material of the fractured part has low ductility, the component fractured in an earlier moment than the one recommended by the manufacturer, the percentages of C, Si, Mn and Cr of the fractured part present values which differ from the design ones, the hardness value of the superior limit of the fractured part is higher than that of the design, and there is no manufacturing uniformity between stock and fractured part. The work will contribute to optimizing the guidance of the actions in a mechanical engineering judicial expertise

Influência do etil-trinexapac no acúmulo, na distribuição de nitrogênio (15N) e na massa de grãos de arroz de terras altas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Viabilidade de utilização de um compósito de matriz cerâmica com cargas recicláveis na fabricação de equipamentos solares

Composite materials can be defined as materials formed from two or more constituents with different compositions, structures and properties, which are separated by an interface. The main objective in producing composites is to combine different materials to produce a single device with superior properties to the component unit. The present study used a composite consisting of plaster, cement, EPS, tire, PET and water to build prototype solar attempt to reduce the manufacturing cost of such equipment. It was built two box type solar cookers, a cooler to be cooled by solar energy, a solar dryer and a solar cooker concentration. For these prototypes were discussed the processes of construction and assembly, determination of thermal and mechanical properties, and raising the performance of such solar systems. Were also determined the proportions of the constituents of the composite materials according to specific performance of each prototype designed. This compound proved to be feasible for the manufacture of such equipment, low cost and easy manufacturing and assembly processes

Produção de biodiesel a partir de óleo de coco (Cocos nucifera L

The production of biodiesel has become an important and attractive process for the production of alternative fuels. This work presents a study of the biodiesel production from coconut oil (Cocos nucifera L.), by two routes: direct transesterification using NaOH as catalyst and esterification (with H2SO4) followed by basic transesterification. The reactor was built in pirex with 1L of capacity and was equipped with a jacket coupled with a thermostatic bath to temperature control, a mecanical stirring is also present in the reactor. The analysis of oil composition was carried out by gas chromatography and esters compounds were identified. The parameters of molar ratio oil/alcohol, reaction time and temperature were studied and their influence on the conversion products was evaluated using experimental planning (23). The molar ratio was the most significant variable by the statistical planning analysis. Conversions up to 85.3% where achived in the esterification/transesterification, with molar ratio 1:6 at 60ºC and 90 minutes of reaction. For the direct transesterification, route conversions up 87.4% eas obtained using 1:6.5 molar ratio at 80ºC and 60 minutes of reaction. The Coconut oil was characterized by their physic chemical properties and key constituents of the oil. The lauric acid was the main constituint and the oil showed high acidity. The biodiesel produced was characterized by its main physicochemical properties, indicating satisfactory results when compared to standard values of National Petroleum Agency. The work was supplemented with a preliminary assessment of the reaction kinetic

Obtenção de emulsões asfálticas convencionais e modificadas com argilas e nanoargilas

The increasing demand for asphalt leads to the development of techniques that can improve the quality of products and increase the useful working life of pavements. Consequently, there is a growing application of asphalt emulsions, which are produced from a mixture of petroleum asphalt cement (CAP) with an aqueous phase. The main advantage of asphalt emulsions is its cold application, reducing energy costs. Conventional emulsions are obtained using asphalt, water, solvent, and additives. The modified asphalt emulsion is developed by adding a modifying agent to conventional emulsions. These modifiers can be natural fibers, waste polymers, nanomaterials. In this work modified asphalt emulsion were obtained using organoclays. First, it was prepared a conventional asphalt emulsion with the following mass proportion: 50% of 50/70 penetration grade CAP, 0.6% of additives and 3% of emulsifier, 20% of solvent and 26.4% of water. It was used bentonite and vermiculite (1% and 4%) to obtain the modified asphalt emulsion. Bentonite and vermiculite were added in its raw state and as an organoclay form and as an organoclay-acid form, resulting in 26 experimental runs. The methodology described by Qian et al. (2011), with modifications, was used to obtain the organoclay and the organoclay-acid form. infrared spectroscopy (IR)) were used to characterize the clays and nanoclays. The emulsions were prepared in a colloidal mill, using 30 minutes and 1 hour as mixing time. After, the emulsions were characterized. The following tests were performed, in accordance with the Brazilian specifications (DNER- 369/97): sieve analysis, Saybolt Furol viscosity, pH determination, density, settlement and storage stability, residue by evaporation, and penetration of residue. Finally, it can be concluded that the use of nanoclays as asphalt modifiers represent a viable alternative to the road paving industry

Avaliação de catalisadores a base de carbeto e nitreto de molibdênio na obtenção de lactitol via hidrogenação da lactose

Seeking a greater appreciation of cheese whey was developed to process the hydrogenation of lactose for the production of lactitol, a polyol with high added value, using the catalyst Ni / activated carbon (15% and 20% nickel), the nitride Mo2N, the bimetallic carbide Ni-Mo/ activated carbon and carbide Mo2C. After synthesis, the prepared catalysts were analyzed by MEV, XRD, laser granulometry and B.E.T. The reactor used in catalytic hydrogenation of lactose was the type of bed mud with a pressure (68 atm), temperature (120 oC) and stirring speed (500 rpm) remained constant during the experiments. The system operated in batch mode for the solid and liquid and semi-continuous to gas. Besides the nature of the catalyst, we studied the influence of pH of reaction medium for Mo2C carbide as well as evaluating the character of the protein inhibitor and chloride ions on the activity of catalysts Ni (20%)/Activated Carbon and bimetallic carbide Ni-Mo/Activated Carbon. The decrease in protein levels was performed by coagulation with chitosan and adsorption of chloride ions was performed by ion exchange resins. In the process of protein adsorption and chloride ions, the maximum percentage extracted was about 74% and 79% respectively. The micrographs of the powders of Mo2C and Mo2N presented in the form of homogeneous clusters, whereas for the catalysts supported on activated carbon, microporous structure proved impregnated with small particles indicating the presence of metal. The results showed high conversion of lactose to lactitol 90% for the catalyst Ni (20%)/Activated Carbon at pH 6 and 46% for the carbide Mo2C pH 8 (after addition of NH4OH) using the commercial lactose. Monitoring the evolution of the constituents present in the reaction medium was made by liquid chromatography. A kinetic model of heterogeneous Langmuir Hinshelwood type was developed which showed that the estimated constants based catalysts promoted carbide and nitride with a certain speed the adsorption, desorption and production of lactitol

Recuperação de fósforo por cristalização de estruvita

This study investigated the influence of the molar ratio, the phosphorus initial concentration, the mixture gradient, mixing time, pH and the secondary nucleation on struvite s crystallization in synthetic water in batch reactors. The study was divided into two stages. The first investigated struvite s crystallization at different Mg:N:P molar ratios and at different initial concentrations of magnesium, nitrogen and phosphorus. It was also evaluated the importance of secondary nucleation on the struvite s crystallization. In the second, five parameters were tested to evaluate their influence on the struvite s crystallization, which were: Mg:N:P molar ratio, initial concentration of phosphate, mixing time, mixture gradient and pH. The best conditions for struvite s crystallization were: Mg:N:P = 1,3:1:1 molar ratio; mixture gradient = 60 rpm, pH = 10.0, mixing time = 5 minutes and high initial concentrations of the constituent ions of struvite. Furthermore, the use of struvite crystals as seed influenced positively on the struvite s crystallization