Use of the storage oscilloscope to train deaf children to convey meaning in sentences through intonation control

This paper is a review of a study to determine if profoundly deaf adolescents could be trained in intonation control in using a two-channel storage oscilloscope.

Precipitating convection in cold air: virtual potential temperature structure

Simulations of precipitating convection are used to illustrate the importance of the turbulent kinetic energy (TKE) budget in determining the virtual potential-temperature structure of the convecting atmosphere. Two sets of simulations are presented: in one the surface temperature was increased to simulate cold air flowing over a warmer surface and in the second a cooling profile, representing cold-air advection, was imposed. It is shown that the terms in the TKE budgets for both sets of simulations scale in the same way, but that the non-dimensional profiles are different. It is suggested that this is associated with the effects of sublimation of ice. It is shown that the magnitudes of the transport and precipitation terms in the virtual potential temperature budget are determined by the scaling of the TKE budget. Some implications of these results for parametrizations of moist convection are discussed. Copyright © 2007 Royal Meteorological Society

Composition and cure temperature: The influence on properties of final flexible PU cold cure foam parts

Foams are cellular structures, produced by gas bubbles formed during the polyurethane polymerization mixture. Flexible PU foams meet the following two criteria: have a limited resistance to an applied load, being both permeable to air and reversibly deformable. There are two main types of flexible foams, hot and cold cure foams differing in composition and processing temperatures. The hot cure foams are widely applied and represent the main composition of actual foams, while cold cure foams present several processing and property advantages, e.g, faster demoulding time, better humid aging properties and more versatility, as hardness variation with index changes are greater than with hot cure foams. The processing of cold cure foams also is attractive due to the low energy consumption (mould temperature from 30 degrees to 65 degrees C) comparatively to hot cure foams (mould temperature from 30 degrees to 250 degrees C). Another advantage is the high variety of soft materials for low temperature processing moulds. Cold cure foams are diphenylmethane diisocyanate (MDI) based while hot cure foams are toluene diisocyanate (TDI) based. This study is concerned with Viscoelastic flexible foams MDI based for medical applications. Differential Scanning Calorimetry (DSC) was used to characterize the cure kinetics and Dynamical Mechanical Analisys to collect mechanical data. The data obtained from these two experimental procedures were analyzed and associated to establish processing/properties/operation conditions relationships. These maps for the selection of optimized processing/properties/operation conditions are important to achieve better final part properties at lower costs and lead times.

Sequential extraction and single-step cold-acid extraction: A feasibility study for use with freshwater-canal sediments

This investigation examines metal release from freshwater sediment using sequential extraction and single-step cold-acid leaching. The concentrations of Cd, Cr, Cu, Fe, Ni, Pb and Zn released using a standard 3-step sequential extraction (Rauret et al., 1999) are compared to those released using a 0.5 M HCl; leach. The results show that the three sediments behave in very different ways when subject to the same leaching experiments: the cold-acid extraction appears to remove higher relative concentrations of metals from the iron-rich sediment than from the other two sediments. Cold-acid extraction appears to be more effective at removing metals from sediments with crystalline iron oxides than the "reducible" step of the sequential extraction. The results show that a single-step acid leach can be just as effective as sequential extractions at removing metals from sediment and are a great deal less time-consuming.

Formation and circulation of the cold intermediate layer in the Gulf of Saint Lawrence

[ 1] The local heat content and formation rate of the cold intermediate layer (CIL) in the Gulf of Saint Lawrence are examined using a combination of new in situ wintertime observations and a three-dimensional numerical model. The field observations consist of five moorings located throughout the gulf over the period of November 2002 to June 2003. The observations demonstrate a substantially deeper surface mixed layer in the central and northeast gulf than in regions downstream of the buoyant surface outflow from the Saint Lawrence Estuary. The mixed-layer depth in the estuary remains shallow (< 60 m) throughout winter, with the arrival of a layer of near-freezing waters between 40 and 100 m depth in April. An eddy-permitting ice-ocean model with realistic forcing is used to hindcast the period of observation. The model simulates well the seasonal evolution of mixed-layer depth and CIL heat content. Although the greatest heat losses occur in the northeast, the most significant change in CIL heat content over winter occurs in the Anticosti Trough. The observed renewal of CIL in the estuary in spring is captured by the model. The simulation highlights the role of the northwest gulf, and in particular, the separation of the Gaspe Current, in controlling the exchange of CIL between the estuary and the gulf. In order to isolate the effects of inflow through the Strait of Belle Isle on the CIL heat content, we examine a sensitivity experiment in which the strait is closed. This simulation shows that the inflow has a less important effect on the CIL than was suggested by previous studies.