Model for electrodes' filaments of hot cathode fluorescent lamps, during preheating with constant rms current

This paper presents a new model for the representation of electrodes' filaments of hot-cathode fluorescent lamps, during preheating processes based on the injection of currents with constant root mean square (rms) values. The main improvement obtained with this model is the prediction of the R-h/R-c ratio during the preheating process, as a function of the preheating time and of the rms current injected in the electrodes. Using the proposed model, it is possible to obtain an estimate of the time interval and the current that should be provided by the electronic ballast, in order to ensure a suitable preheating process. is estimate of time and current can be used as input data in the design of electronic ballasts with programmed lamp start, permitting the prediction of the R-h/R-c ratio during the initial steps of the design (theoretical analysis and digital simulation). Therefore, the use of the proposed model permits to reduce the necessity of several empirical adjustments in the prototype, in order to set the operation of electronic ballasts during the preheating process. This fact reduces time and costs associated to the global design procedure of electronic ballasts.

Friction losses in valves and fittings for viscoplastic fluids

Data on pressure drop were obtained in stainless steel, sanitary fittings and valves during laminar and turbulent flow of aqueous suspensions of sucrose and bentonite. The rheological properties of these suspensions were determined and the Bingham model provided the best fitting with the experimental data. Friction losses were measured in fully- and partially-open butterfly and plug valves, bends and union. Values of loss coefficients (k(f)) were calculated and correlated as functions of the classical Reynolds number and the Reynolds number proposed by Govier and Aziz (1972) for viscoplastic fluids. The two-k method and a new proposed model presented the best adjustments for the Govier and Aziz Reynolds number, and Hedstrom and classical Reynolds numbers, respectively.

Soil CO2 efflux following rotary tillage of a tropical soil

Stopping the increase of atmospheric CO2 level is an important task and information on how to implement adjustments on tillage practices could help lower Soil CO2 emissions would be helpful. We describe how rotary tiller use on a red latosol affected Soil CO2 efflux. The impact of changing blade rotation speed and rear shield position on soil CO2 efflux was investigated. Significant differences among treatments were observed up to 10 days after tillage. Cumulative CO2 efflux was as much as 40% greater when blade rotation of 216 rpm and a lowered rear shield was compared to blade rotation of 122 rpm and raised shield. This preliminary work suggests that adjusting rotary tiller settings could help reduce CO2 efflux close to that of undisturbed soil, thereby helping to conserve soil carbon in tropical environments. (C) 2004 Elsevier B.V. All rights reserved.

Serum Vitamins in Adult Patients With Short Bowel Syndrome Receiving Intermittent Parenteral Nutrition

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Patients' Expectations of and Satisfaction with Implant-Supported Fixed Partial Dentures and Single Crowns

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Expectations and final evaluation of complete dentures by patients, dentist and dental technician

There is a poor association between the dentist's evaluation of denture quality and patients' satisfaction with their dentures. Possible differences between dental professionals and patients' expectations might help explain differences in outcome evaluations. This study compared scores given by a dentist, a dental technician and patients for their expectations before and their final evaluation after complete dentures treatment. Twenty completely edentulous patients, a prosthodontist and a dental technician provided scores for the expected aesthetic and functional results of their dentures based on a visual analogue scale at baseline. Post-treatment completion ratings were given after adjustments, by dentist and patients. The dental technician provided post-treatment completion ratings after completing the dentures. The patients had higher expectations than the dental technician and the dentist perceived for both aesthetic and function (P < 0.001). The patients also presented higher post-treatment completion ratings than the dental professionals perceived for final aesthetics (P = 0.016, Kendall's W = 0.207). and function (P = 0.002, Kendall's W = 0.303). Only the dentist presented a statistically significant difference between expectations (lower) and final (higher) outcomes for aesthetics (P = 0.017) and function (P = 0.003). There was no correlation between expectations and post-treatment completion ratings according to the patients' age. There was also no correlation between the patients' gender and expectation scores. Patients presented higher expectations regarding their dentures than dental professionals. The dentist believed that dentures would bring fewer benefits than patients did, but his perception of denture benefits post-treatment was significantly higher than his expectations.

Patients' expectations and satisfaction of complete denture therapy and correlation with locus of control

P>Considering the importance of patients' satisfaction with complete denture therapy and the influence of psychosocial aspects and expectations regarding satisfaction with their dentures, the present study aimed to test for a correlation between locus of control profiles and expectations before and satisfaction after complete denture therapy. Sixty-four patients rated their expectations for aesthetic and functional results of complete denture therapy on a 10-cm visual analogue scale (VAS), using scores from 0 (worst results) to 10 (best results). A similar questionnaire was used regarding satisfaction after final denture adjustments. Patients also answered a locus of control questionnaire in the initial interview. anova and a chi-squared test were used to test for correlations among ratings, patient gender and locus of control profiles. The significance level adopted was 0 center dot 05. The expectation ratings before treatment were significantly lower than the post-treatment completion ratings, both for aesthetics (P < 0 center dot 001) and function (P = 0 center dot 004). There was no correlation between locus of control profiles and patients' ratings or between gender and VAS scores. No correlation was found between locus of control profiles and scores for expectations before and satisfaction after complete dentures.

Heritability estimates and genetic correlations for body weight and scrotal circumference adjusted to 12 and 18 months of age for male Nellore cattle

Heritability estimates and genetic correlations were obtained for body weight and scrotal circumference, adjusted, respectively, to 12 (BW12 and SC12) and 18 (BW18 and SC18) months of age, for 10 742 male Nellore cattle. The adjustments to SC12 and SC18 were made using a nonlinear logistic function, while BW12 and BW18 were obtained by linear adjustment. The contemporary groups (CGs) were defined from animals born on the same farm, in the same year and birth season. The mean heritability estimates obtained using the restricted maximum likelihood method in bi-trait analysis were 0.25, 0.25, 0.29 and 0.42 for BW12 BW18, SC12 and SC18, respectively. The genetic correlations were 0.30 +/- 0.11, 0.21 +/- 0.13, 0.21 +/- 0.11, -0.08 +/- 0.15, 0.16 +/- 0.12 and 0.89 +/- 0.04 between the traits BW12 and BW18; BW12 and SC12; BW12 and SC18; BW18 and SC12; BW18 and SC18; and SC12 and SC18. The heritability for SC18 was considerably greater than for SC12 suggesting that this should be included as a selection criterion. The genetic correlation between BW18 and SC12 was close to zero, indicating that these traits did not influence each other The contrary occurred between SC12 and SC18, indicating that selection using one of these could alter the other Because of the mean magnitudes of heritabilities in the various measurements of weight and scrotal perimeter it is suggested that the practice of individual selection for these traits is possible.

Influência da elevaçáo transitória e da elevaçáo sustentada da pressáo arterial sobre a primeira derivada temporal da pressáo ventricular.

PURPOSE--To analyze the influence of transient and sustained elevations of arterial pressure (AP) on the rate of rise of the left ventricular pressure (dp/dt). METHODS--Thirteen anesthetized, thoracotomized and mechanically ventilated dogs, submitted to pharmacological autonomic block (oxprenolol-3 mg/kg plus atropine-0.5 mg/kg). The AP elevation was obtained by mechanical constriction of the descending thoracic aorta. Two protocols were applied to all animals: Transient Arterial Hypertension (TAH) and Sustained Arterial Hypertension (SAH) and the following variables were evaluated: heart rate (HR), systolic (LVSP) and end diastolic (LVEDP) left ventricular pressure and dp/dt. In TAH the variables were analyzed in the basal condition (To) and at the maximal value of AP attained during the transient pressure elevation (TM). In the protocol SAH the variables were evaluated in the conditions: Control (Ho), hypertension 1 (H1) and hypertension 2 (H2). RESULTS--Considering all conditions, there were no significant differences among the values of HR. In the protocol TAH, the LVSP varied from 133 +/- 22 mmHg to 180 +/- 27 mmHg, whereas in SAH the values of LVSP were as follow: HO = 129 +/- 25 mmHg; H1 = 152 = 23 mmHg; H2 = 182 +/- 24 mmHg. LVEDP changed in both protocols: To = 7 +/- 2 mmHg; TM = 13 +/- 2 mmHg (p < 0.05); Ho = 7 +/- 2 mmHg; H1 = 10 +/- 2 mmHg; H2 = 14 +/- 3 mmHg (p < 0.05). During TAH there was no difference between the values of dp/dt (To = 3.303 +/- 598 mmHg/s; TM = 3.350 +/- 653 mmHg/s; p > 0.05), however, there were increases of the dp/dt during SAH (Ho = 3.233 +/- 576 mmHg/s; H1 = 3.831 +/- 667 mmHg/s; H1 = 4.594 +/- 833 mmHg/2; p < 0.05). CONCLUSION--The values of dp/dt are not influenced by transient elevation of AP. Sustained increase of AP activates cardiac adjustments, which results in elevation of dp/dt, by stimulation of contractile state. Probably, the inotropic intervention mechanism is the length dependent activation due to the Frank-Starling mechanism.

Metabolic adaptations induced by long-term fasting in quails

After up to 21 days without food, adult male quails (Coturnix coturnix japonica) lost about 45% of the initial body weight (100-150 g). As in naturally fast-adapted and larger birds, three phases were identified during prolonged fasting in quails. Phase I lasted 2-3 days and was characterized by a rapid decrease in the rate of body weight loss and high fat mobilization. Phase II was longer and characterized by a slow and steady decline in the rates of body weight loss and of nitrogen excretion. The third (critical) period was marked by an abrupt increase in the rates of body weight loss and of nitrogen excretion. Despite their small size, the duration of phase II in quails was relatively long, a clear advantage for the study of the relationships between the several metabolic events that occur during this crucial adaptative period. Also, the beginning of phase III could be precisely determined. Changes in blood glucose, plasma FFA and triacylglycerols levels, as well as in liver and carcass lipid content were similar to those found in other species of birds. Therefore, quails seem to be a suitable model to investigate the biochemical mechanisms involved in the metabolic adjustments to prolonged food deprivation in non fasting-adapted birds. © 1995.

Degradabilidade ruminai da fibra em detergente neutro e do nitrogênio insolúvel em detergente neutro da silagem de milho e do farelo de soja, em bovinos da raça nelore

The nylon bag in situ degradation thecnique was employed to study the ruminai degradability of the neutral detergent fiber and neutral detergent insoluble nitrogen of the corn silage and soybean meal in four rumen fistulated Nellore steers, averaging 36 months of age and 520 kg of liveweight. A randomized completelcs block experimental design was used, where the animals constituted the blocks. It was used diets with two levels of concentrate: 20 and 40%.The forage used in the diets was corn silage, and the concentrate ingredients were: soybean meal, cottonseed meal, corn grain and sorghum grain. The NIDN degradation rate of the corn silage and the soybean meal showed a decrease of 32,1% and of 46,0 % as a function of the higher concentrate level of the diet, but the effective and potential degradability of this fraction were not affected. Concerning to the NDF, the soluble fraction, potentially degradable and undegrable , were not affected by the increase on the diet concentrate level, but for the corn silage, there were 21,8% of reduction on the effective degradability of NDF. The use of lag time promoted higher degradability values for the studied fraction. The obtained values for some evaluated parameters, different from that assumed by CNCPS, showed the necessity of more data about brazilian used feeds, for model adjustments.

Mapeamento do contorno estrutural do embasamento da bacia sedimentar de Curitiba - PR

The sedimentary Curitiba basin is located in the Central-Southern part of the first Parananense plateau, and comprises Curitiba (PR), and part of the neighbour Municipalities (fig.1). It is supposed to be of Plio-Pleistocene age. It has a shallow sedimentary fulfillment, represented by the Guabirotuba formation (BIGARELLA and SALAMUNI, 1962) which is dristributed over a large area of about 3.000km2. The internal geometry, not entirely known yet, is actually object of detailed research, that shows its geological evolution to Cenozoic tectonic movements. For the purpose of this study the definition of the structural contour of the basement and their depo-centers is fundamental. This paper presents the results of the integration of surface and subsurface data, processed by statistical methods, which allowed a more precise definition of the morphostructural framework of the basement. For the analysis of the geological spacial data, specific softwares were used for statistical processing for trend surfaces analysis. The data used in this study are of following types: a) drilling logs for ground water; b) description of surface points of geological maps (CRPM, 1977); c) description of points of geotechnical drillings and down geological survey. The data of 223 drilling logs for ground water were selected out of 770 wells. The description files of 700 outcrops, as well as planialtimetric field data, were used for the localization of the basement outcrop. Thus, a matrix with five columns was set up: utm E-W (x) and utm N-S (y); surface altitude (z); altimetric cote of the contact between sedimentary rocks and the basement (k); isopachs (l). For the study of the basement limits, the analysis of surface trends of 2(nd) and 3(rd) degree polinomial for the altimetric data (figs. 2 and 3) were used. For the residuals the method of the inverse of the square of the distance (fig.4) was used. The adjustments and the explanations of the surfaces were made with the aid of multiple linear regressions. The analysis of 3rd degree polinomial trend surface (fig.3) confirmed that the basement tends to be more exposed towards NNW-SSE explaining better the data trend through an ellipse, which striking NE-SW and dipping SW axis coincides with the trough of the basin observed in the trending surface of the basement. The performed analysis and the respective images offer a good degree of certainty of the geometric model of the Curitiba Basin and of the morphostructure of its basement. The surface trend allows to sketch with a greater degree of confidence the structural contour of the topgraphic surface (figs. 5 and 6) and of the basement (figs. 7 and 8), as well as the delimitation of intermediate structural heights, which were responsible for isolated and assymmetric depocenters. These details are shown in the map of figures 9 and 10. Thus, the Curitiba Basin is made up by a structural trough stretching NE-SW, with maximum preserved depths of about 80m, which are separated by heights and depocenters striking NW-SE (fig. 11). These structural features seems to have been controlled by tectonic reactivation during the Tertiary (HASUI, 1990) and which younger dissection was conditioned by neotectonic processes (SALAMUNI and EBERT, 1994).

VAr planning using genetic algorithm and linear programming

A combined methodology consisting of successive linear programming (SLP) and a simple genetic algorithm (SGA) solves the reactive planning problem. The problem is divided into operating and planning subproblems; the operating subproblem, which is a nonlinear, ill-conditioned and nonconvex problem, consists of determining the voltage control and the adjustment of reactive sources. The planning subproblem consists of obtaining the optimal reactive source expansion considering operational, economical and physical characteristics of the system. SLP solves the optimal reactive dispatch problem related to real variables, while SGA is used to determine the necessary adjustments of both the binary and discrete variables existing in the modelling problem. Once the set of candidate busbars has been defined, the program implemented gives the location and size of the reactive sources needed, if any, to maintain the operating and security constraints.

Drought tolerance of two field-grown clones of Coffea canephora

We compared tolerance to soil drought of two field-grown clones of Coffea canephora (clone 46, drought-sensitive; and clone 120, drought-tolerant). Under irrigation, there were no marked differences between the clones in water relation parameters, gas exchange and total leaf area. Under rainfed conditions, clone 46 showed osmotic adjustment and increased tissue rigidity. These adjustments, however, were incapable of preventing substantial decreases in xylem pressure potential. By contrast, clone 120 did not exhibit osmotic adjustment, but was able to increase tissue elasticity and to maintain xylem pressure potentials to a greater extent than clone 46 (despite having twice the total leaf area of this clone). Stomatal conductance was lowered by drought in clone 120 but not in clone 46. Carbon assimilation per unit leaf area in both clones remained unaffected under stress. Long-term water use efficiency (WUE), as estimated through carbon isotope discrimination, was consistently greater in clone 120 than in clone 46. Because of these traits, clone 120 was better able to postpone dehydration and to maintain whole-tree photosynthesis. It is proposed that these features should decisively contribute to buffer its productivity in drought-prone areas. © 2002 Elsevier Science Ireland Ltd. All rights reserved.

Setting the preheating process of electronic ballasts for hot-cathode fluorescent lamps, considering the Rh/Rc ratio

This paper presents a new model for the representation of the electrodes filaments of fluorescent lamps, during their preheating, and an analysis capable to guide the design of the preheating process in electronic ballasts. The main improvement obtained with the lamp model is the accurate theoretical reproduction of the behavior of the Rh/Rc ratio during the preheating process. In addition, using the proposed methodology based on the lamp model, it is possible to set a proper preheating process to the electrodes filaments, without the necessity of exhaustive empirical adjustments in the prototype, reducing time and costs involved in the design of ballasts with preheating capabilities. © 2006 IEEE.