Engine wear and used oil analysis - comparative study in high speed diesel engines

The operational life and reliability of I.C. engines are limited to a certain extent by the break down of the engine components due to wear. It is advantageous to know the condition of an engine and its components without disassembling for detailed measurements. This paper describes the possibility of employing chemical analysis of the used crank case oil to predict the wear of engine components. It is concluded that the acidity and carbon contents of the crank case oil play a significant role in assessing the wear of copper-lead bearings used for the big end of the connecting rod.

Experimental and numerical investigation of jet injection in a wall bounded supersonic flow

Numerical and experimental studies of a supersonic jet (Helium) inclined at 45 degrees to a oncoming Mach 2 flow have been carried out. The numerical study has been used to arrive at a geometry that could reduce an oncoming Mach 5.75 flow to Mach 2 flow and in determining the jet parameters. Experiments are carried out in the IISc. hypersonic shock tunnel HST2 at similar conditions obtained from numerical studies. Flow visualization studies carried out using Schlieren technique clearly show the presence of the bow shock in front of the jet exposed to supersonic cross flow. The jet Mach number is experimentally found to be approximate to 3. Visual observations show that the jet has penetrated up to 60% of the total height of the chamber.

Investigations of separated flow over backward facing steps in IISc hypersonic shock tunnel

Two backward facing step (2 mm and 3 mm step height) models are selected for surface heat transfer measurements. The platinum thin film gauges are deposited on the Macor inserts using both hand paint and vacuum sputtering technique. Using the Eckert reference temperature method the heating rates has been theoretically calculated along the flat plate portion of the model and the theoretical estimates are compared with experimentally determined surface heat transfer rate. Theoretical analysis of heat flux distribution down stream of the backward facing step model has been carried out using Gai’s non-dimensional analysis. Based on the measured surface heating rates on the backward facing step, the reattachment distance is estimated for 2 and 3 mm step height at nominal Mach number of 7.6. It has been found from the present study that for 2 and 3 mm step height, it approximately takes about 10 and 8 step heights downstream of the model respectively for the flow to re-attach.

Magnetohydrodynamic flow between torsionally oscillating eccentric disks

The unsteady MHD flow of an incompressible, viscous electrically conducting fluid contained between two torsionally oscillating eccentric disks has been investigated. The state of uniform rotation of the central region visualised in the steady flow is seen to be absent in the case of oscillatory flow.

Using Big Data to manage safety-related risk in the upstream oil and gas industry: A research agenda

Despite considerable effort and a broad range of new approaches to safety management over the years, the upstream oil & gas industry has been frustrated by the sector’s stubbornly high rate of injuries and fatalities. This short communication points out, however, that the industry may be in a position to make considerable progress by applying “Big Data” analytical tools to the large volumes of safety-related data that have been collected by these organizations. Toward making this case, we examine existing safety-related information management practices in the upstream oil & gas industry, and specifically note that data in this sector often tends to be highly customized, difficult to analyze using conventional quantitative tools, and frequently ignored. We then contend that the application of new Big Data kinds of analytical techniques could potentially reveal patterns and trends that have been hidden or unknown thus far, and argue that these tools could help the upstream oil & gas sector to improve its injury and fatality statistics. Finally, we offer a research agenda toward accelerating the rate at which Big Data and new analytical capabilities could play a material role in helping the industry to improve its health and safety performance.

Gene flow from Corymbia hybrids in northern New South Wales

Some of the most productive taxa for forestry are interspecific F1 hybrids grown as exotics in the tropics and subtropics. Attributes of resilience, adaptability and vigour which engender the hybrids for wood production, may also exacerbate the risk they present from gene flow to native species gene pools or to local ecologies as weeds. To determine the biological and genetic factors that influence the extent of hybridisation, we examine the distribution and genealogy of wildlings surrounding plantings of locally-exotic Corymbia torelliana (Section Cadageria) near native C. henryi (Section Maculatae) in northern New South Wales. Our study showed pre-mating and pre- and post-zygotic barriers were incomplete, with in situ generation and natural establishment of both F1 hybrids (n = 3) and advanced generation hybrids under the disturbed conditions bordering native forest. As hybrids were located on alluvial flats exposed to frost, they also likely have an extended ecological range relative to native C. henryi. Despite the likely generation of large viable seed crops on F1 trees at the site over many years, establishment success and survival of advanced generation hybrids may be low, as only 5 immature and no mature advanced generation hybrids were identified. Propagation and genetic analysis of a seed crop from one F1 wildling showed early survival and vigour of seedlings in cultivation was high, and that at least for some F1 in some seasons, backcrossing to the recurrent native C. henryi parent is favoured (60%), whereas selfing (10%) and crossing with other F1 (30%) was less frequent. Transport of seed by stingless bees probably accounted for long distance dispersal from C. torelliana, but this mechanism does not appear to supplement gravity-dispersal of seed from the F1. Coupled with other evidence from studies of bee behaviour, controlled pollination in Corymbia sp., and long-term fitness in second generation eucalypt hybrids, we anticipate gene flow via pollen rather than seed will be the greater challenge for managing the risk of introgression of C. torelliana ancestry into native species from the planted F1 hybrid. If large sources of F1 pollen become available to compete with native pollen, gene flow will probably be frequent and hybrids may establish in disturbed conditions and in habitats beyond the ecological range of their native parent. Further study is needed to determine the degree to which outbreeding depression and poor survival inhibits on-going gene flow.

Evaluation of chlorothalonil and paraffinic oil alone and in combinations with registered fungicides for the control of yellow Sigatoka (Mycosphaerella musicola) of bananas in Northern Queensland, Australia

The efficacy of chlorothalonil and paraffinic oil alone and in combinations with the registered fungicides propiconazole, tebuconazole, difenoconazole, epoxiconazole and pyrimethanil was evaluated in a field experiment over two cropping cycles in 2013 and 2014 in Northern Queensland, Australia, for control of yellow Sigatoka (caused by Mycosphaerella musicola) of banana. The predominantly applied by the banana industry treatment mancozeb with paraffinic oil was included for comparison. The results from the two cropping cycles suggested that all chemicals used with paraffinic oil were as effective or more effective than when applied with chlorothalonil, and chlorothalonil alone. Difenoconazole and epoxiconazole with paraffinic oil followed by propiconazole with paraffinic oil were the most effective treatments. Pyrimethanil and tebuconazole plus chlorothalonil were the least effective treatments. None of the chemical treatments was phytotoxic or reduced yield.

Engine wear and used oil analysis-A comparative study in high speed diesel engines

The operational life and reliability of I.C. engines are limited to a certain extent by the break down of the engine components due to wear. It is advantageous to know the condition of an engine and its components without disassembling for detailed measurements. This paper describes the possibility of employing chemical analysis of the used crank case oil to predict the wear of engine components. It is concluded that the acidity and carbon contents of the crank case oil play a significant role in assessing the wear of copper-lead bearings used for the big end of the connecting rod.

Superhydrophobic fabrics for oil-water separation based on the metal organic charge transfer complex CuTCNAQ

This work reports on the fabrication of a superhydrophobic nylon textile based on the organic charge transfer complex CuTCNAQ (TCNAQ = 11,11,12,12-tetracyanoanthraquinodimethane). The nylon fabric that is metallized with copper undergoes a spontaneous chemical reaction with TCNAQ dissolved in acetonitrile to form nanorods of CuTCNAQ that are intertwined over the entire surface of the fabric. This creates the necessary micro and nanoscale roughness that is required for the Cassie-Baxter state thereby achieving a superhydrophobic/superoleophilic surface without the need for a fluorinated surface. The material is characterised with SEM, FT-IR and XPS spectroscopy and investigated for its ability to separate oil and water in two modes, namely under gravity and as an absorbent. It is found that the fabric can separate dichloromethane, olive oil and crude oil from water and in fact reduce the water content of the oil during the separation process. The fabric is reusable and tolerant to conditions such as seawater, hydrochloric acid and extensive time periods on the shelf. Given that CuTCNAQ is a copper based semiconductor may also open up the possibility of other applications in areas such as photocatalysis and antibacterial applications.

Unsteady laminar boundary layers in a compressible stagnation flow

The unsteady laminar compressible boundary-layer flow in the immediate vicinity of a two-dimensional stagnation point due to an incident stream whose velocity varies arbitrarily with time is considered. The governing partial differential equations, involving both time and the independent similarity variable, are transformed into new co-ordinates with finite ranges by means of a transformation which maps an infinite interval into a finite one. The resulting equations are solved by converting them into a matrix equation through the application of implicit finite-difference formulae. Computations have been carried out for two particular unsteady free-stream velocity distributions: (1) a constantly accelerating stream and (2) a fluctuating stream. The results show that in the former case both the skin-friction and the heat-transfer parameter increase steadily with time after a certain instant, while in the latter they oscillate thus responding to the fluctuations in the free-stream velocity.

Intrinsic equations of steady rotating, incompressible viscous fluid flow

The equations governing the flow of a steady rotating incompressible viscous fluid are expressed in intrinsic form along the vortex lines and their normals. Using these equations the effects of rotation on the geometric properties of viscous fluid flows are studied. A particular flow in which the vortex lines are right circular helices is discussed.