Numerical modelling of single-layer folding: clarification of an issue regarding the possible effect of computer codes and the influence of initial irregularities

The influence of initial perturbation geometry and material propel-ties on final fold geometry has been investigated using finite-difference (FLAC) and finite-element (MARC) numerical models. Previous studies using these two different codes reported very different folding behaviour although the material properties, boundary conditions and initial perturbation geometries were similar. The current results establish that the discrepancy was not due to the different computer codes but due to the different strain rates employed in the two previous studies (i.e. 10(-6) s(-1) in the FLAC models and 10(-14) s(-1) in the MARC models). As a result, different parts of the elasto-viscous rheological field were bring investigated. For the same material properties, strain rate and boundary conditions, the present results using the two different codes are consistent. A transition in Folding behaviour, from a situation where the geometry of initial perturbation determines final fold shape to a situation where material properties control the final geometry, is produced using both models. This transition takes place with increasing strain rate, decreasing elastic moduli or increasing viscosity (reflecting in each case the increasing influence of the elastic component in the Maxwell elastoviscous rheology). The transition described here is mechanically feasible but is associated with very high stresses in the competent layer (on the order of GPa), which is improbable under natural conditions. (C) 2000 Elsevier Science Ltd. All rights reserved.

Resistance to temperature extremes between and within life cycle stages in Drosophila serrata, D-birchii and their hybrids: intraspecific and interspecific comparisons

Intraspecific Drosophila studies suggest that resistance to heal and cold stresses are largely independent and that correlations across life cycle stages are low whereas comparisons of Drosophila species indicate correlations between heat and cold resistance as well as between resistance levels in different life cycle stages. These inconsistent results may reflect differences in associations among traits at the interspecific and intraspecific levels or interspecific correlations arising because of correlated selection pressures. These alternatives were tested using Drosophila serrata, D. birchii and hybrids derived from these species. Variation among hybrid lines and families was used to test associations at the interspecific level while intraspecific variation was examined using isofemale lines of D. serrata. There was a significant association between adult heat knockdown time at 38 degreesC and adult cold resistance in one set of hybrid lines. An association between female knockdown resistance to heat and larval heat resistance was also evident in one set of hybrids. Resistance to heat anti cold at the larval stage were not correlated at either the intraspecific or interspecific levels. At the intraspecific level, lan al heat resistance and two measures of adult heat resistance were uncorrelated. Moreover, adult and larval cold resistance measures were not correlated at either the intraspecific or interspecific levels. These results suggest that there are no associations between resistance to heat and cold extremes and that extreme temperature resistance is largely independent across life cycle stages at both the intraspecific and interspecific levels. Species associations may therefore arise from correlated selection pressures rather than trait correlations. (C) 2000 The Linnean Society of London.

Resident tissue macrophages within the normal rat iris lack immunosuppressive activity and are effective antigen-presenting cells

Despite extensive study of the numerous immunoregulatory mechanisms that contribute to the immune-privileged nature of the anterior chamber (AC) of the eye, little is known of the functional nature of antigen-presenting cells (APC) present in the tissues adjoining the AC. In the present study, we have compared the antigen-presenting capacity of dendritic cells (DC) and macrophages isolated from the normal rat iris. Whereas iris DC exhibited a potent ability to stimulate resting allogeneic T cells in MLR cultures (an in-vitro correlate of the ability to induce primary T cell responses), resident iris macrophages displayed negligible MLR-stimulatory capacity. Significantly, iris macrophages could efficiently elicit proliferation of primed antigen-specific T cells (an in-vitro correlate of the ability to act as local APC in secondary responses). This antigen-presenting activity was approximately half that of fully mature iris DC and considerably greater than that of freshly isolated iris DC. A key contributor to the effectiveness of resident iris macrophage antigen presentation was considered to be the absence of lymphocytostatic control of T cell proliferation exerted by these cells. The results indicate dichotomous but complementary roles for DC (immune surveillance) and macrophages (local antigen presentation in secondary responses) in this tissue.

Foraging and vein-cutting behaviour of Euploea core corinna (W.S. Macleay) (Lepidoptera : Nymphalidae) caterpillars feeding on latex-bearing leaves

Caterpillars of Euploea core corinna (W. S. Macleay) sever leaf veins prior to feeding on their latex-bearing host plants, which restricts the flow of latex at feeding sites. The severing of leaf veins by insects feeding on latex-bearing plants is commonly referred to as 'sabotaging' and is thought to be an evolved response by the insect to counter the negative effects of feeding on latex-rich leaves. Sabotaging behaviour is described for all instars of E. core corinna, with particular attention given to neonates. Vein cutting by neonate E. core corinna caterpillars can occur within 2 h of hatching, with most caterpillars establishing feeding sites within 10 h. Commonly, first instars cut an are-shaped row of leaf side-veins parallel to the leaf margin, but they may also cut the leaf mid-rib in a fashion similar to older instar larvae. From a sample of 50 E. core corinna larvae, representing all instars, we found that the diameters of the veins cut by caterpillars are closely correlated to larval head width (r=0.90). Through manipulative experiments, we demonstrate for the first time that sabotaging behaviour in neonate caterpillars imposes no detectable short-term physiological costs on those caterpillars.

Tetraphyllidean metacestodes of teleosts of the Great Barrier Reef, and the use of in vitro cultivation to identify them

The tetraphyllidean metacestode diversity of 310 teleost fishes, including 87 species from 31 families, was examined from Heron Island, The Great Barrier Reef, Australia. Eleven metacestode 'types' were identified with the use of light microscopy. Host-specificity varied greatly among metacestode types. Incorporation of in vitro cultivation allowed generic identification for some types. Types 1 and 2 belong to Uncibilocularis Southwell, 1925, and have triloculate bothridia and one pair of Forked hooks with unequal prongs; Type 3 has quadriloculate bothridia. Hook development was insufficient to determine in which genus, Acanthobothrium van Beneden, 1849 or Calliobothrium van Beneden, 1850, this type may belong. Type 4 has unilocular bothridia with simple edges and belongs to Anthobothrium van Beneden, 1850. Type 5 has multiloculated bothridia which are invaginated within pouches. This type belongs to the Rhinebothriinae although its generic identity cannot be determined. The bothridia of Type 5 everted within 24 hours of in vitro cultivation and revealed the presence of two forms, one having 48 loculi per bothridium, the other 72 per bothridium. In vitro studies provide additional support for existing theories of onchobothriid scolex development.

Hybrid modelling of coupled pore fluid-solid deformation problems

A hybrid formulation for coupled pore fluid-solid deformation problems is proposed. The scheme is a hybrid in the sense that we use a vertex centered finite volume formulation for the analysis of the pore fluid and a particle method for the solid in our model. The pore fluid formally occupies the same space as the solid particles. The size of the particles is not necessarily equal to the physical size of materials. A finite volume mesh for the pore fluid flow is generated by Delaunay triangulation. Each triangle possesses an initial porosity. Changes of the porosity are specified by the translations of the mass centers of particles. Net pore pressure gradients are applied to the particle centers and are considered in the particle momentum balance. The potential of our model is illustrated by means of a simulation of coupled fracture and fluid flow developed in porous rock under biaxial compression condition.

Finite element modelling of three-dimensional convection problems in fluid-saturated porous media heated from below

We use the finite element method to model three-dimensional convective pore-fluid flow in fluid-saturated porous media when they are heated from below. In particular, we employ the particle-tracking technique to mimic the trajectories of particles in three-dimensional fluid flow problems. The related numerical results demonstrated that: (1) The progressive asymptotic approach procedure, which was previously developed for the finite element modelling of two-dimensional convective pore-fluid flow problems, is equally applicable to the finite element modelling of three-dimensional convective pore-fluid flow in fluid-saturated porous media heated from below. (2) The perturbation of gravity at different planes has a significant effect on the pattern of three-dimensional convective pore-fluid flow and therefore, may influence the pattern of orebody formation and mineralization in three-dimensional hydrothermal systems. Copyright (C) 2001 John Wiley & Sons, Ltd.

Two new species of Neolebouria Gibson, 1976 (Digenea : Opecoelidae) from temperate marine fishes of Australia

Neolebouria moretonensis n. sp. is described from Gerres subfasciatus (Gerreidae) from Moreton Bay, south-east Queensland and N. lineatus n. sp. is described from Centroberyx lineatus (Berycidae) from off Rottnest Island, south-west Western Australia. C. lineatus represents a new host family and order (Beryciformes) for the genus. The two new species are distinguished within the genus by their entire, tandem to oblique testes and cirrus-sacs that do not extend into the hind-body, by being less than 1 mm in length, and by the position of the genital pore and the relative size of the forebody and post-testicular region. N. lineatus and N. moretonensis are very similar but are distinguished by their caeca which extend further posteriorly in N. moretonensis. There is no apparent pattern in the host-specificity of this genus.

Modelling solute transport in structured soils: Performance evaluation of the ADR and TRM models

The movement of chemicals through the soil to the groundwater or discharged to surface waters represents a degradation of these resources. In many cases, serious human and stock health implications are associated with this form of pollution. The chemicals of interest include nutrients, pesticides, salts, and industrial wastes. Recent studies have shown that current models and methods do not adequately describe the leaching of nutrients through soil, often underestimating the risk of groundwater contamination by surface-applied chemicals, and overestimating the concentration of resident solutes. This inaccuracy results primarily from ignoring soil structure and nonequilibrium between soil constituents, water, and solutes. A multiple sample percolation system (MSPS), consisting of 25 individual collection wells, was constructed to study the effects of localized soil heterogeneities on the transport of nutrients (NO3-, Cl-, PO43-) in the vadose zone of an agricultural soil predominantly dominated by clay. Very significant variations in drainage patterns across a small spatial scale were observed tone-way ANOVA, p < 0.001) indicating considerable heterogeneity in water flow patterns and nutrient leaching. Using data collected from the multiple sample percolation experiments, this paper compares the performance of two mathematical models for predicting solute transport, the advective-dispersion model with a reaction term (ADR), and a two-region preferential flow model (TRM) suitable for modelling nonequilibrium transport. These results have implications for modelling solute transport and predicting nutrient loading on a larger scale. (C) 2001 Elsevier Science Ltd. All rights reserved.

Modelling life history strategies with capture-recapture data: Evolutionary demography of the water skink Eulamprus tympanum

Matrix population models, elasticity analysis and loop analysis can potentially provide powerful techniques for the analysis of life histories. Data from a capture-recapture study on a population of southern highland water skinks (Eulamprus tympanum) were used to construct a matrix population model. Errors in elasticities were calculated by using the parametric bootstrap technique. Elasticity and loop analyses were then conducted to identify the life history stages most important to fitness. The same techniques were used to investigate the relative importance of fast versus slow growth, and rapid versus delayed reproduction. Mature water skinks were long-lived, but there was high immature mortality. The most sensitive life history stage was the subadult stage. It is suggested that life history evolution in E. tympanum may be strongly affected by predation, particularly by birds. Because our population declined over the study, slow growth and delayed reproduction were the optimal life history strategies over this period. Although the techniques of evolutionary demography provide a powerful approach for the analysis of life histories, there are formidable logistical obstacles in gathering enough high-quality data for robust estimates of the critical parameters.

Disaggregation of polygons of surficial geology and soil maps using spatial modelling and legacy data

Examples from the Murray-Darling basin in Australia are used to illustrate different methods of disaggregation of reconnaissance-scale maps. One approach for disaggregation revolves around the de-convolution of the soil-landscape paradigm elaborated during a soil survey. The descriptions of soil ma units and block diagrams in a soil survey report detail soil-landscape relationships or soil toposequences that can be used to disaggregate map units into component landscape elements. Toposequences can be visualised on a computer by combining soil maps with digital elevation data. Expert knowledge or statistics can be used to implement the disaggregation. Use of a restructuring element and k-means clustering are illustrated. Another approach to disaggregation uses training areas to develop rules to extrapolate detailed mapping into other, larger areas where detailed mapping is unavailable. A two-level decision tree example is presented. At one level, the decision tree method is used to capture mapping rules from the training area; at another level, it is used to define the domain over which those rules can be extrapolated. (C) 2001 Elsevier Science B.V. All rights reserved.

Modelling socially optimal land allocations for sugar cane growing in North Queensland: a linked mathematical programming and choice modelling study

A modelling framework is developed to determine the joint economic and environmental net benefits of alternative land allocation strategies. Estimates of community preferences for preservation of natural land, derived from a choice modelling study, are used as input to a model of agricultural production in an optimisation framework. The trade-offs between agricultural production and environmental protection are analysed using the sugar industry of the Herbert River district of north Queensland as an example. Spatially-differentiated resource attributes and the opportunity costs of natural land determine the optimal tradeoffs between production and conservation for a range of sugar prices.

Modelling of post-irradiation events in polymer gel dosimeters

The nuclear magnetic resonance (NMR) spin-spin relaxation time (T-2) is related to the radiation-dependent concentration of polymer formed in polymer gel dosimeters manufactured from monomers in an aqueous gelatin matrix. Changes in T-2 with time post-irradiation have been reported in the literature but their nature is not fully understood. We investigated those changes with time after irradiation using FT-Raman spectroscopy and the precise determination of T-2 at high magnetic field in a polymer gel dosimeter, A model of fast exchange of magnetization taking into account ongoing gelation and strengthening of the gelatin matrix as well as the polymerization of the monomers with time is presented. Published data on the changes of T-2 in gelatin gels as a function of post-manufacture time are used and fitted closely by the model presented. The same set of parameters characterizing the variations of T-2 in gelatin gels and the increasing concentration of polymer determined from Fr-Raman spectroscopy are used successfully in the modelling of irradiated polymer gel dosimeters. Minimal variations in T-2 in an irradiated PAG dosimeter are observed after 13 h.

Promoter studies of a polydnavirus gene from Cotesia rubecula (Hym : Braconidae)

The Cotesia rubecula polydnavirus gene, CrV1, is expressed in a highly transient fashion. Within four hours after egg deposition and virus infection, tissues of the host caterpillar, Pieris rapae, express high levels of the transcript. Twelve hours after infection no transcripts are visible. We have previously shown that the CrV1 secreted protein is mainly produced in host haemocytes. In haemocytes, immune functions such as phagocytosis and cell spreading are abolished by destabilization of the cell cytoskeleton. To test whether the observed down-regulation of CrV1 transcripts is mediated by transcriptional control or by other factors, such as the disruption of cytoskeleton in CrV1-inactivated cells, we cloned the promoter and the 3' untranslated region of the CrV1 gene to study CrV1 expression. The promoter region of the CrV1 gene was cloned into baculovirus expression systems along with the CAT reporter gene. Molecular analyses showed that the CAT gene under the control of CrV1 promoter is expressed as early as 2 h post infection and continues until late phase of infection suggesting that down-regulation of CrV1 expression in host haemocytes is perhaps mediated by post-transcriptional mechanisms.