Flexural behaviour and design of the new built-up LiteSteel beams

LiteSteel Beam (LSB) is a new cold-formed steel beam produced by OneSteel Australian Tube Mills. The new beam is effectively a channel section with two rectangular hollow flanges and a slender web, and is manufactured using a combined cold-forming and electric resistance welding process. OneSteel Australian Tube Mills is promoting the use of LSBs as flexural members in a range of applications, such as floor bearers. When LSBs are used as back to back built-up sections, they are likely to improve their moment capacity and thus extend their applications further. However, the structural behaviour of built-up beams is not well understood. Many steel design codes include guidelines for connecting two channels to form a built-up I-section including the required longitudinal spacing of connections. But these rules were found to be inadequate in some applications. Currently the safe spans of builtup beams are determined based on twice the moment capacity of a single section. Research has shown that these guidelines are conservative. Therefore large scale lateral buckling tests and advanced numerical analyses were undertaken to investigate the flexural behaviour of back to back LSBs connected by fasteners (bolts) at various longitudinal spacings under uniform moment conditions. In this research an experimental investigation was first undertaken to study the flexural behaviour of back to back LSBs including its buckling characteristics. This experimental study included tensile coupon tests, initial geometric imperfection measurements and lateral buckling tests. The initial geometric imperfection measurements taken on several back to back LSB specimens showed that the back to back bolting process is not likely to alter the imperfections, and the measured imperfections are well below the fabrication tolerance limits. Twelve large scale lateral buckling tests were conducted to investigate the behaviour of back to back built-up LSBs with various longitudinal fastener spacings under uniform moment conditions. Tests also included two single LSB specimens. Test results showed that the back to back LSBs gave higher moment capacities in comparison with single LSBs, and the fastener spacing influenced the ultimate moment capacities. As the fastener spacing was reduced the ultimate moment capacities of back to back LSBs increased. Finite element models of back to back LSBs with varying fastener spacings were then developed to conduct a detailed parametric study on the flexural behaviour of back to back built-up LSBs. Two finite element models were developed, namely experimental and ideal finite element models. The models included the complex contact behaviour between LSB web elements and intermittently fastened bolted connections along the web elements. They were validated by comparing their results with experimental results and numerical results obtained from an established buckling analysis program called THIN-WALL. These comparisons showed that the developed models could accurately predict both the elastic lateral distortional buckling moments and the non-linear ultimate moment capacities of back to back LSBs. Therefore the ideal finite element models incorporating ideal simply supported boundary conditions and uniform moment conditions were used in a detailed parametric study on the flexural behaviour of back to back LSB members. In the detailed parametric study, both elastic buckling and nonlinear analyses of back to back LSBs were conducted for 13 LSB sections with varying spans and fastener spacings. Finite element analysis results confirmed that the current design rules in AS/NZS 4600 (SA, 2005) are very conservative while the new design rules developed by Anapayan and Mahendran (2009a) for single LSB members were also found to be conservative. Thus new member capacity design rules were developed for back to back LSB members as a function of non-dimensional member slenderness. New empirical equations were also developed to aid in the calculation of elastic lateral distortional buckling moments of intermittently fastened back to back LSBs. Design guidelines were developed for the maximum fastener spacing of back to back LSBs in order to optimise the use of fasteners. A closer fastener spacing of span/6 was recommended for intermediate spans and some long spans where the influence of fastener spacing was found to be high. In the last phase of this research, a detailed investigation was conducted to investigate the potential use of different types of connections and stiffeners in improving the flexural strength of back to back LSB members. It was found that using transverse web stiffeners was the most cost-effective and simple strengthening method. It is recommended that web stiffeners are used at the supports and every third points within the span, and their thickness is in the range of 3 to 5 mm depending on the size of LSB section. The use of web stiffeners eliminated most of the lateral distortional buckling effects and hence improved the ultimate moment capacities. A suitable design equation was developed to calculate the elastic lateral buckling moments of back to back LSBs with the above recommended web stiffener configuration while the same design rules developed for unstiffened back to back LSBs were recommended to calculate the ultimate moment capacities.

A ‘cost-per-wear’ model based on contact lens replacement frequency

Purpose: The aim was to construct and advise on the use of a cost-per-wear model based on contact lens replacement frequency, to form an equitable basis for cost comparison. ---------- Methods: The annual cost of professional fees, contact lenses and solutions when wearing daily, two-weekly and monthly replacement contact lenses is determined in the context of the Australian market for spherical, toric and multifocal prescription types. This annual cost is divided by the number of times lenses are worn per year, resulting in a ‘cost-per-wear’. The model is presented graphically as the cost-per-wear versus the number of times lenses are worn each week for daily replacement and reusable (two-weekly and monthly replacement) lenses.---------- Results: The cost-per-wear for two-weekly and monthly replacement spherical lenses is almost identical but decreases with increasing frequency of wear. The cost-per-wear of daily replacement spherical lenses is lower than for reusable spherical lenses, when worn from one to four days per week but higher when worn six or seven days per week. The point at which the cost-per-wear is virtually the same for all three spherical lens replacement frequencies (approximately AUD$3.00) is five days of lens wear per week. A similar but upwardly displaced (higher cost) pattern is observed for toric lenses, with the cross-over point occurring between three and four days of wear per week (AUD$4.80). Multifocal lenses have the highest price, with cross-over points for daily versus two-weekly replacement lenses at between four and five days of wear per week (AUD$5.00) and for daily versus monthly replacement lenses at three days per week (AUD$5.50).---------- Conclusions: This cost-per-wear model can be used to assist practitioners and patients in making an informed decision in relation to the cost of contact lens wear as one of many considerations that must be taken into account when deciding on the most suitable lens replacement modality.

Global trends in prescribing contact lenses for extended wear

Extended wear has long been the ‘holy grail’ of contact lenses by virtue of the increased convenience and freedom of lifestyle which they accord; however, this modality enjoyed only limited market success during the last quarter of the 20th century. The introduction of silicone hydrogel materials into the market at the beginning of this century heralded the promise of successful extended wear due to the superior oxygen performance of this lens type. To assess patterns of contact lens fitting, including extended wear, over the past decade, up to 1000 survey forms were sent to contact lens fitters in Australia, Canada, Japan, the Netherlands, Norway, the UK and the USA each year between 2000 and 2009. Practitioners were asked to record data relating to the first 10 contact lens fits or refits performed after receiving the survey form. Analysis of returned forms revealed that, averaged over this period, 9% of all soft lenses prescribed were for extended wear, with national figures ranging from 2% in Japan to 17% in Norway. The trend over the past decade has been for an increase from about 5% of all soft lens fits in 2000 to a peak of between 9 and 12% between 2002 and 2007, followed by a decline to around 7% in 2009. A person receiving extended wear lenses is likely to be an older female who is being refitted with silicone hydrogel lenses for full-time wear. Although extended wear has yet again failed to fulfil the promise of being the dominant contact lens wearing modality, it is still a viable option for many people.

Ecological and social characterization of key resource areas in Kenyan rangelands

Key resource areas (KRAs), defined as dry season foraging zones for herbivores, were studied relative to the more extensive outlying rangeland areas (non-KRAs) in Kenya. Field surveys with pastoralists, ranchers, scientists and government officials delineated KRAs on the ground. Identified KRAs were mapped based on global positioning and local experts' information on KRAs accessibility and ecological attributes. Using the map of known KRAs and non-KRAs, we examined characteristics of soils, climate, topography, land use/cover attributes at KRAs relative to non-KRAs. How and why do some areas (KRAs) support herbivores during droughts when forage is scarce in other areas of the landscape? We hypothesized that KRAs have fundamental ecological and socially determined attributes that enable them to provide forage during critical times and we sought to characterize some of those attributes in this study. At the landscape level, KRAs took different forms based on forage availability during the dry season but generally occurred in locations of the landscape with aseasonal water availability and/or difficult to access areas during wet season forage abundance. Greenness trends for KRAs versus non-KRAs were evaluated with a 22-year dataset of Normalized Difference Vegetation Index (NDVI). Field surveys of KRAs provided qualitative information on KRAs as dry season foraging zones. At the scale of the study, soil attributes did not significantly differ for KRAs compared to non-KRAs. Slopes of KRA were generally steeper compared to non-KRAs and elevation was higher at KRAs. Field survey respondents indicated that animals and humans generally avoid difficult to access hilly areas using them only when all other easily accessible rangeland is depleted of forage during droughts. Understanding the nature of KRAs will support identification, protection and restoration of critical forage hotspots for herbivores by strengthening rangeland inventory, monitoring, policy formulation, and conservation efforts to improve habitats and human welfare. (c) 2007 Elsevier Ltd. All rights reserved.

Sustained convergence, axial length, and corneal topography

Purpose: To investigate the influence of convergence on axial length and corneal topography in young adult subjects.---------- Methods: Fifteen emmetropic young adult subjects with normal binocular vision had axial length and corneal topography measured immediately before and after a 15-min period of base out (BO) prismatic spectacle lens wear. Two different magnitude prismatic spectacles were worn in turn (8 [DELTA] BO and 16 [DELTA] BO), and for both tasks, distance fixation was maintained for the duration of lens wear. Eight subjects returned on a separate day for further testing and had axial length measured before, during, and immediately after a 15-min convergence task.---------- Results: No significant change was found to occur in axial length either during or after the sustained convergence tasks (p > 0.6). Some small but significant changes in corneal topography were found to occur after sustained convergence. The most significant corneal change was observed after the 16 [DELTA] BO prism wear. The corneal refractive power spherocylinder power vector J0 was found to change by a small (mean change of 0.03 D after the 16 [DELTA] BO task) but statistically significant (p = 0.03) amount as a result of the convergence task (indicative of a reduction in with-the-rule corneal astigmatism after convergence). Corneal axial power was found to exhibit a significant flattening in superior regions. Conclusions: Axial length appears largely unchanged by a period of sustained convergence. However, small but significant changes occur in the topography of the cornea after convergence.

Regional changes in corneal thickness and shape with soft contact lenses

Purpose: To investigate the influence of soft contact lenses on regional variations in corneal thickness and shape while taking account of natural diurnal variations in these corneal parameters. Methods: Twelve young, healthy subjects wore 4 different types of soft contact lenses on 4 different days. The lenses were of two different materials (silicone hydrogel, hydrogel), designs (spherical, toric) and powers (–3.00, –7.00 D). Corneal thickness and topography measurements were taken before and after 8 hours of lens wear and on two days without lens wear, using the Pentacam HR system. Results: The hydrogel toric contact lens caused the greatest level of corneal thickening in the central (20.3 ± 10.0 microns) as well as peripheral cornea (24.1 ± 9.1 microns) (p < 0.001) with an obvious regional swelling of the cornea beneath the stabilizing zones. The anterior corneal surface generally showed slight flattening. All contact lenses resulted in central posterior corneal steepening and this was weakly correlated with central corneal swelling (p = 0.03) and peripheral corneal swelling (p = 0.01). Conclusions: There was an obvious regional corneal swelling apparent after wear of the hydrogel soft toric lenses, due to the location of the thicker stabilization zones of the toric lenses. However with the exception of the hydrogel toric lens, the magnitude of corneal swelling induced by the contact lenses over the 8 hours of wear was less than the natural diurnal thinning of the cornea over this same period.

Socioeconomic inequality profiles in physical and developmental health from 0-7 years : Australian National Study

Background: Early and persistent exposure to socioeconomic disadvantage impairs children’s health and wellbeing. However, it is unclear at what age health inequalities emerge or whether these relationships vary across ages and outcomes. We address these issues using cross-sectional Australian population data on the physical and developmental health of children at ages 0-1, 2-3, 4-5 and 6-7 years. Methods: 10 physical and developmental health outcomes were assessed in 2004 and 2006 for two cohorts each comprising around 5000 children. Socioeconomic position was measured as a composite of parental education, occupation and household income. Results: Lower socioeconomic position was associated with increased odds for poor outcomes. For physical health outcomes and socio-emotional competence, associations were similar across age groups and were consistent with either threshold effects (for poor general health, special healthcare needs and socio-emotional competence) or gradient effects (for illness with wheeze, sleep problems and injury). For socio-emotional difficulties, communication, vocabulary and emergent literacy, stronger socioeconomic associations were observed. The patterns were linear or accelerated and varied across ages. Conclusions: From very early childhood, social disadvantage was associated with poorer outcomes across most measures of physical and developmental health and showed no evidence of either strengthening or attenuating at older compared to younger ages. Findings confirm the importance of early childhood as a key focus for health promotion and prevention efforts.

Strengthening of circular hollow steel tubular sections using high modulus CFRP sheets

This paper describes the behaviour of very high strength (VHS) circular steel tubes strengthened by carbon fibre reinforced polymer (CFRP) and subjected to axial tension. A series of tests were conducted with different bond lengths and number of layers. The distribution of strain through the thickness of CFRP layers and along CFRP bond length was studied. The strain was found to generally decrease along the CFRP bond length far from the joint. The strain through the thickness of the CFRP layers was also found to decrease from bottom to top layer. The effective bond length for high modulus CFRP was established. Finally empirical models were developed to estimate the maximum load for a given CFRP arrangement.

Confocal microscopy of the bulbar conjunctiva in contact lens wear

Purpose: The aim of this study was to investigate the capabilities of laser scanning confocal microscopy (LSCM) for undertaking qualitative and quantitative investigations of the response of the bulbar conjunctiva to contact lens wear. Methods: LSCM was used to observe and measure morphological characteristics of the bulbar conjunctiva of 11 asymptomatic soft contact lens wearers and 11 healthy volunteer subjects (controls). Results: The appearance of the bulbar conjunctiva is consistent with known histology of this tissue based on light and electron microscopy. The thickness of the bulbar conjunctival epithelium of lens wearers (30.9 ± 1.1 μm) was less than that of controls (32.9 ± 1.1 μm) (P < 0.0001). Superficial and basal bulbar conjunctival epithelial cell densities in contact lens wearers were 91% and 79% higher, respectively, than that in controls (P < 0.0001). No difference was observed in goblet and Langerhans cell density between lens wearers and controls. Conjunctival microcysts were observed in greater numbers, and were larger in size, in lens wearers compared with controls. Conclusions: The effects of contact lens wear on the human bulbar conjunctiva can be investigated effectively at a cellular level using LSCM. The observations in this study suggest that contact lens wear can induce changes in the bulbar conjunctiva such as epithelial thinning and accelerated formation and enlargement of microcysts, increased epithelial cell density, but has no impact on goblet or Langerhans cell density.

In vivo performance of melimine as an antimicrobial coating for contact lenses in models of CLARE and CLPU

Purpose: One strategy to minimize bacteria-associated adverse responses such as microbial keratitis, contact lens–induced acute red eye (CLARE), and contact lens induced peripheral ulcers (CLPUs) that occur with contact lens wear is the development of an antimicrobial or antiadhesive contact lens. Cationic peptides represent a novel approach for the development of antimicrobial lenses.---------- Methods: A novel cationic peptide, melimine, was covalently incorporated into silicone hydrogel lenses. Confirmation tests to determine the presence of peptide and anti-microbial activity were performed. Cationic lenses were then tested for their ability to prevent CLPU in the Staphylococcus aureus rabbit model and CLARE in the Pseudomonas aeruginosa guinea pig model. ---------- Results: In the rabbit model of CLPU, melimine-coated lenses resulted in significant reductions in ocular symptom scores and in the extent of corneal infiltration (P < 0.05). Evaluation of the performance of melimine lenses in the CLARE model showed significant improvement in all ocular response parameters measured, including the percentage of eyes with corneal infiltrates, compared with those observed in the eyes fitted with the control lens (P ≤ 0.05). ---------- Conclusions: Cationic coating of contact lenses with the peptide melimine may represent a novel method of prevention of bacterial growth on contact lenses and consequently result in reduction of the incidence and severity of adverse responses due to Gram-positive and -negative bacteria during lens wear.

Nursing and Midwifery Services Strategic Directions, 2011-2015

This document presents the newly updated strategic directions for strengthening nursing and midwifery services (SDNM) for the period 2011–2015. Complementing and building on the 2002–2008 SDNM, it seeks to provide policymakers, practitioners and other stakeholders at every level with a flexible framework for broad-based, collaborative action to enhance the capacity of nurses and midwives to contribute to: * universal coverage * people-centred health care * policies affecting their practice and working conditions, and the * scaling up of national health systems to meet global goals and targets. The SDNM for 2011–2015 draws on several key World Health Assembly resolutions, and are underpinned by the associated global policy recommendations and codes of practice. (1,2) After two years of extensive research and consultation, a SDNM task force was developed, and a consensus on a range of specific activities revolving around 13 objectives in five interrelated key results areas (KRAs), was achieved: n health system and service strengthening n policy and practice * education, training and career development * workforce management and * partnership. Stakeholders, although free to prioritize certain parts of the framework to meet their own particular needs, are encouraged to adhere to the cornerstone of collaborative action, namely the common goal enshrined in the core SDNM 2011–2015 vision statement: improved health outcomes for individuals, families and communities through the provision of competent, culturally sensitive, evidence-based nursing and midwifery services.

Pedagogy and participation : literacy education for low-literate refugee students of African origin in a western school system

For ESL teachers working with low-literate adolescents the challenge is to provide instruction in basic literacy capabilities while also realising the benefits of interactive and dialogic pedagogies advocated for the students. In this article we look at literacy pedagogy for refugees of African origin in Australian classrooms. We report on an interview study conducted in an intensive English language school for new arrival adolescents and in three regular secondary schools. Brian Street’s ideological model is used. From this perspective, literacy entails not only technical skills, but also social and cultural ways of making meaning that are embedded within relations of power. The findings showed that teachers were strengthening control of instruction to enable mastery of technical capabilities in basic literacy and genre analysis. We suggest that this approach should be supplemented by a critical approach transforming relations of linguistic power that exclude, marginalise and humiliate the study students in the classroom.

Punitiveness and the criminalisation of the other : State wards, unlawful non-citizens and Indigenous youth

This paper explores the genealogies of bio-power that cut across punitive state interventions aimed at regulating or normalising several distinctive ‘problem’ or ‘suspect’ deviant populations, such as state wards, non-lawful citizens and Indigenous youth. It begins by making some general comments about the theoretical approach to bio-power taken in this paper. It then outlines the distinctive features of bio-power in Australia and how these intersected with the emergence of penal welfarism to govern the unruly, unchaste, unlawful, and the primitive. The paper draws on three examples to illustrate the argument – the gargantuan criminalisation rates of Aboriginal youth, the history of incarcerating state wards in state institutions, and the mandatory detention of unlawful non-citizens and their children. The construction of Indigenous people as a dangerous presence, alongside the construction of the unruly neglected children of the colony — the larrikin descendants of convicts as necessitating special regimes of internal controls and institutions, found a counterpart in the racial and other exclusionary criteria operating through immigration controls for much of the twentieth century. In each case the problem child or population was expelled from the social body through forms of bio-power, rationalised as strengthening, protecting or purifying the Australian population.

Novice riders and the predictors of riding without motorcycle protective clothing

Background While helmet usage is often mandated, few motorcycle and scooter riders make full use of protection for the rest of the body. Little is known about the factors associated with riders’ usage or non-usage of protective clothing. Methods Novice riders were surveyed prior to their provisional licence test in NSW, Australia. Questions related to usage and beliefs about protective clothing, riding experience and exposure, risk taking and demographic details. Multivariable Poisson regression models were used to identify factors associated with two measures of usage, comparing those who sometimes vs rarely/never rode unprotected and who usually wore non-motorcycle pants vs motorcycle pants. Results Ninety-four percent of eligible riders participated and usable data was obtained from 66% (n = 776). Factors significantly associated with riding unprotected were: youth (17–25 years) (RR = 2.00, 95% CI: 1.50–2.65), not seeking protective clothing information (RR = 1.29, 95% CI = 1.07–1.56), non-usage in hot weather (RR = 3.01, 95% CI: 2.38–3.82), awareness of social pressure to wear more protection (RR = 1.48, 95% CI: 1.12–1.95), scepticism about protective benefits (RR = 2.00, 95% CI: 1.22–3.28) and riding a scooter vs any type of motorcycle. A similar cluster of factors including youth (RR = 1.17, 95% CI: 1.04–1.32), social pressure (RR = 1.32, 95% CI: 1.16–1.50), hot weather (RR = 1.30, 95% CI: 1.19–1.41) and scooter vs motorcycles were also associated with wearing non-motorcycle pants. There was no evidence of an association between use of protective clothing and other indicators of risk taking behaviour. Conclusions Factors strongly associated with non-use of protective clothing include not having sought information about protective clothing and not believing in its injury reduction value. Interventions to increase use may therefore need to focus on development of credible information sources about crash risk and the benefits of protective clothing. Further work is required to develop motorcycle protective clothing suitable for hot climates.