Evaluation of elevator shafts as a pathway for fungal spores and particles to enter a hospital housing immuno-compromised patients

Background. It is estimated that hospitals spend between 28 and 33 billion dollars per year as a result of hospital-acquired infections. (Scott, 2009) The costs continue to rise despite the guidance and controls provided by hospital infection control staff to reduce patient exposures to fungal spores and other infectious agents. With all processes and controls in place, the vented elevator shaft represents an unprotected opening from the top of the building to the lower floors. The hypothesis for this prospective study is that there is a positive correlation between the number of Penicillium/Aspergillus-like spores, Cladosporium, ascospores, basidiospores in spores/m3 as individual spore categories found in the hoistway vent of an elevator shaft and the levels of the same spores, sampled near-simultaneously in the outdoor intake of the elevator shaft. Specific aims of this study include determining if external Penicillium/Aspergillus-like spores are entering the healthcare facility via the elevator shaft and hoistway vents. Additional aims include determining levels of Penicillium/Aspergillus-like spores outdoors, in the elevator shafts, and indoors in areas possibly affected by elevator shaft air; and, finally, to evaluate whether any effect is observed due to the installation of a hoistway vent damper, installed serendipitously during this study. ^ Methods. Between April 2010 and September 2010, a total of 3,521 air samples were collected, including 363 spore trap samples analyzed microscopically for seven spore types, and polymerase chain reaction analyses on 254 air samples. 2178 particle count measurements, 363 temperature readings and 363 relative humidity readings were also obtained from 7 different locations potentially related to the path of air travel inside and near a centrally-located and representative elevator shaft. ^ Results. Mean Penicillium/Aspergillus-like spore values were higher outside the building (530 spores/m3 of air) than inside the hoistway (22.8 spores/m3) during the six month study. Mean values inside the hospital were lower than outside throughout the study, ranging from 15 to 73 spores/m3 of air. Mean Penicillium/Aspergillus-like spore counts inside the hoistway decreased from 40.1 spores/m3 of air to 9 spores/m3 of air following the installation of a back draft damper between the outside air and the elevator shaft. Comparison of samples collected outside the building and inside the hoistway vent prior to installing the damper indicated a strong positive correlation (Spearman's Rho=0.8008, p=0.0001). The similar comparison following the damper installation indicated a moderate non-significant inverse correlation (Spearman's rho = −0.2795, p=0.1347). ^ Conclusion. Elevator shafts are one pathway for mold spores to enter a healthcare facility. A significant correlation was detected between spores and particle counts inside the hoistway and outside prior to changes in the ventilation system. The insertion of the back draft damper appeared to lower the spore counts inside the hoistway and inside the building. The mold spore counts in air outside the study building were higher in the period following the damper installation while the levels inside the hoistway and hospital decreased. Cladosporium and Penicillium/Aspergillus -like spores provided a method for evaluating indoor air quality as a natural tracer from outside the building to inside the building. Ascospores and basidiospores were not a valuable tracer due to low levels of detection during this study. ^ Installation of a back draft damper provides additional protection for the indoor environment of a hospital or healthcare facility, including in particular patients who may be immunocompromised. Current design standards and references do not require the installation of a back draft damper, but evaluation of adding language to relevant building codes should be considered. The data indicate a reduction in levels of Penicillium/Aspergillus -like spores, particle counts and a reduction in relative humidity inside of the elevator shaft after damper installation.^

Exploring the association of children's engagement in nature and outdoor activity with physical activity: A systematic review

The natural environment and green spaces are settings that may facilitate physical activity and, as a result, combat childhood obesity and benefit children's physical health. A systematic review was conducted to assess the effect of children's engagement in outdoor activity on children's physical activity levels. A total of 169 articles were initially identified, of which 11 were eligible for inclusion in the systematic review. Studies were heterogeneous: cross-sectional, RCT, cohort, and direct observation. Study participants were between the ages of 3-15 years, and physical activity was measured by accelerometers, pedometers, direct observation or surveys. A majority of the studies (9/11) found a positive association between time spent outdoors and physical activity in children and adolescents. Of these 9 studies, 5 found this association specifically between time spent outdoors in greenspace and physical activity. Despite limitations, the findings of this review support the positive association between time spent outdoors and physical activity in children and adolescents, and the notion that children and adolescents who spend more time outdoors are more physically active. This demonstrates the need to use outdoor environments as settings for children's and adolescents' physical activity.^

Evaluation of a wellness program at a large private sector petrochemical company in Texas

The study purpose was to analyze the effects Integrated Health Solutions (IHS), an employee wellness program that has been implemented for one year on the corporate campus of a major private sector petrochemical company in Houston, TX, has on employee health. ^ Chronic diseases are the leading causes of morbidity and mortality in the United States and are the most preventable of all health problems. The costs of chronic diseases in the working-age adult population include not only health problems and a decrease in quality of life, but also an increase the cost of health care and costs to businesses and employers, both directly and indirectly. These emerging costs to employers as well as the fact that adults now spend the majority of waking hours at the office have increased the interest in worksite health promotion programs that address many of the behavioral factors that lead to chronic conditions. Therefore, implementing and evaluating programs that are aimed at promoting health and decreasing the prevalence of chronic diseases at worksites is very important. ^ Data came from existing data that were collected by IHS staff during employee biometric screenings at the company in 2010 and 2011. Data from employees who participated in screenings in both 2010 and 2011 were grouped into a cohort by IHS staff. ^ One-tailed t-tests were conducted to determine if there were significant improvements in the biometric measures of body fat percentage, BMI, waist circumference, systolic and diastolic blood pressures, total, HDL, and LDL cholesterol levels, triglycerides, blood glucose levels, and cardiac risk ratios. Sensitivity analysis was conducted to determine if there were differences in program outcomes when stratified by age, gender, job type, and time between screenings. ^ Mean differences for the variables from 2010 to 2011 were small and not always in the desired direction for health improvement indicators. Through conducting t-tests, it was found that there were significant improvements in HDL, cardiac risk ratio, and glucose levels. There were significant increases in cholesterol, LDL, and diastolic blood pressures. For the IHS program, it appears that gender, job type, and time between screenings were possible modifiers of program effectiveness. When program outcome measures were stratified by these factors, results suggest that corporate employees had better outcomes than field employees, males had better outcomes overall than females, and more positive program effects were seen for employees with less time between their two screenings. ^ Recommendations for the program based on the results include ensuring validity of instruments and initial and periodic training of measurement procedures and equipment handling, using normative data or benchmarks to decrease chances for biased estimates of program effectiveness, measuring behaviors as well as biometric and physiologic statuses and changes, and collecting level of engagement data.^

Relationships, Income Support and Decision Making: A Qualitative Synopsis

This qualitative study of one midwestern state’s child protective services addresses whether an income support measure for poor biological caregivers reduces the length of time that their children spend in foster care. The overall findings suggest that workers do value the worker-family relationship. However, some view the immediate worker-client relationship as secondary to the inclusion of extended familial supports particularly as related to sustained more long-term outcome achievement. Most workers additionally agree that client involvement during all phases of the reunification process is critical.

El trabajo remunerado y no remunerado en Rosario : la desigual distribución de los tiempos entre varones y mujeres

El presente trabajo estudia los patrones de uso del tiempo de la población de la ciudad de Rosario en base a la Encuesta de Uso del Tiempo y Voluntariado del año 2010, realizada utilizando la metodología del “diario de actividades" del día anterior. Por un lado, se evidenció la existencia de una fuerte división sexual del trabajo en la que los varones dedican más tiempo al trabajo realizado para el mercado que las mujeres, y en la que las mujeres destinan casi tres veces más tiempo que los varones al trabajo no remunerado (doméstico y de cuidados). En segundo lugar se comprobó la existencia de una doble jornada femenina a partir del hecho de que las mujeres trabajan (remunerada y no remuneradamente) una mayor cantidad de horas que los varones, y se verificó que las mujeres trabajan más horas pero ganan menos, principalmente dado que su mayor carga de trabajo no recibe ninguna remuneración. Por último, a partir del análisis en función del nivel de ingresos se aprecia una desigualdad adicional intra-mujeres, siendo que aquellas que viven en hogares de menores ingresos dedican una mayor cantidad de tiempo al trabajo no remunerado que aquellas de hogares de mayores ingresos.

"Excluidos por excelencia" : Revisiones de un concepto para el caso de los habitantes de la calle

La problemática del "habitar la calle", es decir, la situación que actualmente atraviesan miles de personas y familias de tener que pasar noches y días en las calles de la ciudad, es un fenómeno cada vez más notorio en nuestro país y en las grandes ciudades del planeta. En el mundo académico se ha intentado realizar un acercamiento a esta cuestión desde múltiples enfoques y conceptos; uno de ellos es el de exclusión social. Este concepto nacido en el continente europeo, en la década del ochenta, a partir de la crisis que atravesó la sociedad salarial, es retomado en América Latina en los años 90. Actualmente es ampliamente utilizado para comprender las situaciones de extrema pobreza y precariedad laboral. Precisamente, en este artículo se propone un acercamiento a ciertos aspectos de la experiencia del "habitar la calle" a través de la exploración del concepto de exclusión social. Esta noción, que expresa la situación de los "excluidos" del mundo social, es revisada a partir del caso de los habitantes de la calle, generalmente considerados como los "excluidos por excelencia".

"Excluidos por excelencia" : Revisiones de un concepto para el caso de los habitantes de la calle

La problemática del "habitar la calle", es decir, la situación que actualmente atraviesan miles de personas y familias de tener que pasar noches y días en las calles de la ciudad, es un fenómeno cada vez más notorio en nuestro país y en las grandes ciudades del planeta. En el mundo académico se ha intentado realizar un acercamiento a esta cuestión desde múltiples enfoques y conceptos; uno de ellos es el de exclusión social. Este concepto nacido en el continente europeo, en la década del ochenta, a partir de la crisis que atravesó la sociedad salarial, es retomado en América Latina en los años 90. Actualmente es ampliamente utilizado para comprender las situaciones de extrema pobreza y precariedad laboral. Precisamente, en este artículo se propone un acercamiento a ciertos aspectos de la experiencia del "habitar la calle" a través de la exploración del concepto de exclusión social. Esta noción, que expresa la situación de los "excluidos" del mundo social, es revisada a partir del caso de los habitantes de la calle, generalmente considerados como los "excluidos por excelencia".

"Excluidos por excelencia" : Revisiones de un concepto para el caso de los habitantes de la calle

La problemática del "habitar la calle", es decir, la situación que actualmente atraviesan miles de personas y familias de tener que pasar noches y días en las calles de la ciudad, es un fenómeno cada vez más notorio en nuestro país y en las grandes ciudades del planeta. En el mundo académico se ha intentado realizar un acercamiento a esta cuestión desde múltiples enfoques y conceptos; uno de ellos es el de exclusión social. Este concepto nacido en el continente europeo, en la década del ochenta, a partir de la crisis que atravesó la sociedad salarial, es retomado en América Latina en los años 90. Actualmente es ampliamente utilizado para comprender las situaciones de extrema pobreza y precariedad laboral. Precisamente, en este artículo se propone un acercamiento a ciertos aspectos de la experiencia del "habitar la calle" a través de la exploración del concepto de exclusión social. Esta noción, que expresa la situación de los "excluidos" del mundo social, es revisada a partir del caso de los habitantes de la calle, generalmente considerados como los "excluidos por excelencia".

Dive depth and dive duration data of female southern elephant seals from Marion Island between 2004 and 2008 with links to datasets

The at-sea behaviour of marine top predators provides valuable insights into the distribution of prey species and strategies used by predators to exploit patchily distributed resources. We describe the water column usage and dive strategies of female southern elephant seals from Marion Island tracked between 2004 and 2008. Dives representing increases in forage effort were identified using a method that combines dive type analyses and the calculation of relative amounts of time that animals spend in the bottom phases of dives. Results from this analysis indicate that female elephant seals from Marion Island tend to display lower levels of forage effort closer to the island and display intensive opportunistic forage bouts that occur at a minimum distance of approximately 215 km from the island. Females from Marion Island dived deeper and for longer periods of time, compared to females from other populations. Most animals displayed positive diel vertical migration, evidently foraging pelagically on vertically migrating prey. A few animals displayed periods of reverse (negative) diel vertical migration, however, diving to deeper depths at night, compared to daytime. This behaviour is difficult to explain and prey species targeted during such periods unknown. Our results illustrate plasticity in foraging behaviour of southern elephant seals, as well as inter-population differences in forage strategies.

(Table 1) Movement parameters of nine adult female snowy owls (Bubo scandiacus) tracked during the winter period 07/08 and 08/09 around Hudson Strait, Canada

Top predators of the arctic tundra are facing a long period of very low prey availability during winter and subsidies from other ecosystems such as the marine environment may help to support their populations. Satellite tracking of snowy owls, a top predator of the tundra, revealed that most adult females breeding in the Canadian Arctic overwinter at high latitudes in the eastern Arctic and spend several weeks (up to 101 d) on the sea-ice between December and April. Analysis of high-resolution satellite images of sea-ice indicated that owls were primarily gathering around open water patches in the ice, which are commonly used by wintering seabirds, a potential prey. Such extensive use of sea-ice by a tundra predator considered a small mammal specialist was unexpected, and suggests that marine resources subsidize snowy owl populations in winter. As sea-ice regimes in winter are expected to change over the next decades due to climate warming, this may affect the wintering strategy of this top predator and ultimately the functioning of the tundra ecosystem.

The effects of long (C20/22) and short (C18) chain omega-3 fatty acids on keel bone fractures, bone biomechanics, behavior, and egg production in free-range laying hens.

Keel fractures in the laying hen are the most critical animal welfare issue facing the egg production industry, particularly with the increased use of extensive systems in response to the 2012 EU directive banning conventional battery cages. The current study is aimed at assessing the effects of 2 omega-3 (n3) enhanced diets on bone health, production endpoints, and behavior in free-range laying hens. Data was collected from 2 experiments over 2 laying cycles, each of which compared a (n3) supplemented diet with a control diet. Experiment 1 employed a diet supplemented with a 60:40 fish oil-linseed mixture (n3:n6 to 1.35) compared with a control diet (n3:n6 to 0.11), whereas the n3 diet in Experiment 2 was supplemented with a 40:60 fish oil-linseed (n3:n6 to 0.77) compared to the control diet (n3:n6 to 0.11). The n3 enhanced diet of Experiment 1 had a higher n3:n6 ratio, and a greater proportion of n3 in the long chain (C20/22) form (0.41 LC:SC) than that of Experiment 2 (0.12 LC:SC). Although dietary treatment was successful in reducing the frequency of fractures by approximately 27% in Experiment 2, data from Experiment 1 indicated the diet actually induced a greater likelihood of fracture (odds ratio: 1.2) and had substantial production detriment. Reduced keel breakage during Experiment 2 could be related to changes in bone health as n3-supplemented birds demonstrated greater load at failure of the keel, and tibiae and humeri that were more flexible. These results support previous findings that n3-supplemented diets can reduce fracture likely by increasing bone strength, and that this can be achieved without detriment to production. However, our findings suggest diets with excessive quantities of n3, or very high levels of C20/22, may experience health and production detriments. Further research is needed to optimize the quantity and type of n3 in terms of bone health and production variables and investigate the potential associated mechanisms.

Fiscal Decentralization, Chinese Style: Good for Health Outcomes?

This study analyzes the effect of fiscal decentralization on health outcomes in China using a panel data set with nationwide county-level data. We find that counties in more fiscal decentralized provinces have lower infant mortality rates compared to those counties in which the provincial government retains the main spending authority, if certain conditions are met. Spending responsibilities at the local level need to be matched with county government's own fiscal capacity. For those local governments that have only limited revenues, their ability to spend on local public goods such as health care depends crucially upon intergovernmental transfers. The findings of this study thereby support the common assertion that fiscal decentralization can indeed lead to more efficient production of local public goods, but also highlights the necessary conditions to make this happen.

The Bangladesh gender gap in education : biased intra-household educational expenditures

By investigating the educational expenditure of children over the ten years (2000 to 2010), we evaluate whether there exists any gender specific discrepancy at the household level and the trend of such discrepancy over the years. Using three rounds of nationally representative Household Income & Expenditure Surveys this study reveals that households spend less on education for their school-going girls compared to boys. By disaggregating the total expenditure into fixed and variable components, we find persistent gender imbalance in educational expenditure where households provide better quality of education for boys. Moreover, we find that gender based discrepancy has a very persistent trend and does not show any significant sign of narrowing the gap over the years. Cohort wise difference-in-difference estimation also reveals that the gap has initially widened and later converged but has not diminished beyond the initial level of discrepancy, which may warrant targeted policy intervention.

Effect of bird age and storage system on physical properties of eggs from brown laying hens

A total of 108 eggs from a group of 100 brown laying hens housed in standard cages were analyzed. Thirty-six eggs were retired when the hens had 30 week of age, other 36 eggs were retired when the hens had 35 week of age and the remaining 36 eggs were retired five weeks afterwards. Each group of 36 eggs was radomly divided in three groups of 12 eggs. First group was analyzed at once, second group one was kept during one week in the refrigerator (5°C) and third group was kept also one week but on ambient temperature (25°C). Shell color, shell thickness, specific gravity, albumen height and Haugh units wre obtained. The bird age had significant effect on shell color and shell thickness, but the storage system had not influence on such variables. The hen age had not effect on specific gravity, but the storage system affected to this variable. Hen age and storage system had significant influence (P<0.05) on albumen height and Haugh units, and the interaction age × storage system was significant for these variables. The specific gravity had positive relations with shell thickness, yolk color, albumen height and Haugh units. It is concluded that bird age and storage system under high temperatures reduced the egg quality.

Applications for wireless sensor networks : tracking with binary proximity sensors

El interés cada vez mayor por las redes de sensores inalámbricos pueden ser entendido simplemente pensando en lo que esencialmente son: un gran número de pequeños nodos sensores autoalimentados que recogen información o detectan eventos especiales y se comunican de manera inalámbrica, con el objetivo final de entregar sus datos procesados a una estación base. Los nodos sensores están densamente desplegados dentro del área de interés, se pueden desplegar al azar y tienen capacidad de cooperación. Por lo general, estos dispositivos son pequeños y de bajo costo, de modo que pueden ser producidos y desplegados en gran numero aunque sus recursos en términos de energía, memoria, velocidad de cálculo y ancho de banda están enormemente limitados. Detección, tratamiento y comunicación son tres elementos clave cuya combinación en un pequeño dispositivo permite lograr un gran número de aplicaciones. Las redes de sensores proporcionan oportunidades sin fin, pero al mismo tiempo plantean retos formidables, tales como lograr el máximo rendimiento de una energía que es escasa y por lo general un recurso no renovable. Sin embargo, los recientes avances en la integración a gran escala, integrado de hardware de computación, comunicaciones, y en general, la convergencia de la informática y las comunicaciones, están haciendo de esta tecnología emergente una realidad. Del mismo modo, los avances en la nanotecnología están empezando a hacer que todo gire entorno a las redes de pequeños sensores y actuadores distribuidos. Hay diferentes tipos de sensores tales como sensores de presión, acelerómetros, cámaras, sensores térmicos o un simple micrófono. Supervisan las condiciones presentes en diferentes lugares tales como la temperatura, humedad, el movimiento, la luminosidad, presión, composición del suelo, los niveles de ruido, la presencia o ausencia de ciertos tipos de objetos, los niveles de tensión mecánica sobre objetos adheridos y las características momentáneas tales como la velocidad , la dirección y el tamaño de un objeto, etc. Se comprobara el estado de las Redes Inalámbricas de Sensores y se revisaran los protocolos más famosos. Así mismo, se examinara la identificación por radiofrecuencia (RFID) ya que se está convirtiendo en algo actual y su presencia importante. La RFID tiene un papel crucial que desempeñar en el futuro en el mundo de los negocios y los individuos por igual. El impacto mundial que ha tenido la identificación sin cables está ejerciendo fuertes presiones en la tecnología RFID, los servicios de investigación y desarrollo, desarrollo de normas, el cumplimiento de la seguridad y la privacidad y muchos más. Su potencial económico se ha demostrado en algunos países mientras que otros están simplemente en etapas de planificación o en etapas piloto, pero aun tiene que afianzarse o desarrollarse a través de la modernización de los modelos de negocio y aplicaciones para poder tener un mayor impacto en la sociedad. Las posibles aplicaciones de redes de sensores son de interés para la mayoría de campos. La monitorización ambiental, la guerra, la educación infantil, la vigilancia, la micro-cirugía y la agricultura son solo unos pocos ejemplos de los muchísimos campos en los que tienen cabida las redes mencionadas anteriormente. Estados Unidos de América es probablemente el país que más ha investigado en esta área por lo que veremos muchas soluciones propuestas provenientes de ese país. Universidades como Berkeley, UCLA (Universidad de California, Los Ángeles) Harvard y empresas como Intel lideran dichas investigaciones. Pero no solo EE.UU. usa e investiga las redes de sensores inalámbricos. La Universidad de Southampton, por ejemplo, está desarrollando una tecnología para monitorear el comportamiento de los glaciares mediante redes de sensores que contribuyen a la investigación fundamental en glaciología y de las redes de sensores inalámbricos. Así mismo, Coalesenses GmbH (Alemania) y Zurich ETH están trabajando en diversas aplicaciones para redes de sensores inalámbricos en numerosas áreas. Una solución española será la elegida para ser examinada más a fondo por ser innovadora, adaptable y polivalente. Este estudio del sensor se ha centrado principalmente en aplicaciones de tráfico, pero no se puede olvidar la lista de más de 50 aplicaciones diferentes que ha sido publicada por la firma creadora de este sensor específico. En la actualidad hay muchas tecnologías de vigilancia de vehículos, incluidos los sensores de bucle, cámaras de video, sensores de imagen, sensores infrarrojos, radares de microondas, GPS, etc. El rendimiento es aceptable, pero no suficiente, debido a su limitada cobertura y caros costos de implementación y mantenimiento, especialmente este ultimo. Tienen defectos tales como: línea de visión, baja exactitud, dependen mucho del ambiente y del clima, no se puede realizar trabajos de mantenimiento sin interrumpir las mediciones, la noche puede condicionar muchos de ellos, tienen altos costos de instalación y mantenimiento, etc. Por consiguiente, en las aplicaciones reales de circulación, los datos recibidos son insuficientes o malos en términos de tiempo real debido al escaso número de detectores y su costo. Con el aumento de vehículos en las redes viales urbanas las tecnologías de detección de vehículos se enfrentan a nuevas exigencias. Las redes de sensores inalámbricos son actualmente una de las tecnologías más avanzadas y una revolución en la detección de información remota y en las aplicaciones de recogida. Las perspectivas de aplicación en el sistema inteligente de transporte son muy amplias. Con este fin se ha desarrollado un programa de localización de objetivos y recuento utilizando una red de sensores binarios. Esto permite que el sensor necesite mucha menos energía durante la transmisión de información y que los dispositivos sean más independientes con el fin de tener un mejor control de tráfico. La aplicación se centra en la eficacia de la colaboración de los sensores en el seguimiento más que en los protocolos de comunicación utilizados por los nodos sensores. Las operaciones de salida y retorno en las vacaciones son un buen ejemplo de por qué es necesario llevar la cuenta de los coches en las carreteras. Para ello se ha desarrollado una simulación en Matlab con el objetivo localizar objetivos y contarlos con una red de sensores binarios. Dicho programa se podría implementar en el sensor que Libelium, la empresa creadora del sensor que se examinara concienzudamente, ha desarrollado. Esto permitiría que el aparato necesitase mucha menos energía durante la transmisión de información y los dispositivos sean más independientes. Los prometedores resultados obtenidos indican que los sensores de proximidad binarios pueden formar la base de una arquitectura robusta para la vigilancia de áreas amplias y para el seguimiento de objetivos. Cuando el movimiento de dichos objetivos es suficientemente suave, no tiene cambios bruscos de trayectoria, el algoritmo ClusterTrack proporciona un rendimiento excelente en términos de identificación y seguimiento de trayectorias los objetos designados como blancos. Este algoritmo podría, por supuesto, ser utilizado para numerosas aplicaciones y se podría seguir esta línea de trabajo para futuras investigaciones. No es sorprendente que las redes de sensores de binarios de proximidad hayan atraído mucha atención últimamente ya que, a pesar de la información mínima de un sensor de proximidad binario proporciona, las redes de este tipo pueden realizar un seguimiento de todo tipo de objetivos con la precisión suficiente. Abstract The increasing interest in wireless sensor networks can be promptly understood simply by thinking about what they essentially are: a large number of small sensing self-powered nodes which gather information or detect special events and communicate in a wireless fashion, with the end goal of handing their processed data to a base station. The sensor nodes are densely deployed inside the phenomenon, they deploy random and have cooperative capabilities. Usually these devices are small and inexpensive, so that they can be produced and deployed in large numbers, and so their resources in terms of energy, memory, computational speed and bandwidth are severely constrained. Sensing, processing and communication are three key elements whose combination in one tiny device gives rise to a vast number of applications. Sensor networks provide endless opportunities, but at the same time pose formidable challenges, such as the fact that energy is a scarce and usually non-renewable resource. However, recent advances in low power Very Large Scale Integration, embedded computing, communication hardware, and in general, the convergence of computing and communications, are making this emerging technology a reality. Likewise, advances in nanotechnology and Micro Electro-Mechanical Systems are pushing toward networks of tiny distributed sensors and actuators. There are different sensors such as pressure, accelerometer, camera, thermal, and microphone. They monitor conditions at different locations, such as temperature, humidity, vehicular movement, lightning condition, pressure, soil makeup, noise levels, the presence or absence of certain kinds of objects, mechanical stress levels on attached objects, the current characteristics such as speed, direction and size of an object, etc. The state of Wireless Sensor Networks will be checked and the most famous protocols reviewed. As Radio Frequency Identification (RFID) is becoming extremely present and important nowadays, it will be examined as well. RFID has a crucial role to play in business and for individuals alike going forward. The impact of ‘wireless’ identification is exerting strong pressures in RFID technology and services research and development, standards development, security compliance and privacy, and many more. The economic value is proven in some countries while others are just on the verge of planning or in pilot stages, but the wider spread of usage has yet to take hold or unfold through the modernisation of business models and applications. Possible applications of sensor networks are of interest to the most diverse fields. Environmental monitoring, warfare, child education, surveillance, micro-surgery, and agriculture are only a few examples. Some real hardware applications in the United States of America will be checked as it is probably the country that has investigated most in this area. Universities like Berkeley, UCLA (University of California, Los Angeles) Harvard and enterprises such as Intel are leading those investigations. But not just USA has been using and investigating wireless sensor networks. University of Southampton e.g. is to develop technology to monitor glacier behaviour using sensor networks contributing to fundamental research in glaciology and wireless sensor networks. Coalesenses GmbH (Germany) and ETH Zurich are working in applying wireless sensor networks in many different areas too. A Spanish solution will be the one examined more thoroughly for being innovative, adaptable and multipurpose. This study of the sensor has been focused mainly to traffic applications but it cannot be forgotten the more than 50 different application compilation that has been published by this specific sensor’s firm. Currently there are many vehicle surveillance technologies including loop sensors, video cameras, image sensors, infrared sensors, microwave radar, GPS, etc. The performance is acceptable but not sufficient because of their limited coverage and expensive costs of implementation and maintenance, specially the last one. They have defects such as: line-ofsight, low exactness, depending on environment and weather, cannot perform no-stop work whether daytime or night, high costs for installation and maintenance, etc. Consequently, in actual traffic applications the received data is insufficient or bad in terms of real-time owed to detector quantity and cost. With the increase of vehicle in urban road networks, the vehicle detection technologies are confronted with new requirements. Wireless sensor network is the state of the art technology and a revolution in remote information sensing and collection applications. It has broad prospect of application in intelligent transportation system. An application for target tracking and counting using a network of binary sensors has been developed. This would allow the appliance to spend much less energy when transmitting information and to make more independent devices in order to have a better traffic control. The application is focused on the efficacy of collaborative tracking rather than on the communication protocols used by the sensor nodes. Holiday crowds are a good case in which it is necessary to keep count of the cars on the roads. To this end a Matlab simulation has been produced for target tracking and counting using a network of binary sensors that e.g. could be implemented in Libelium’s solution. Libelium is the enterprise that has developed the sensor that will be deeply examined. This would allow the appliance to spend much less energy when transmitting information and to make more independent devices. The promising results obtained indicate that binary proximity sensors can form the basis for a robust architecture for wide area surveillance and tracking. When the target paths are smooth enough ClusterTrack particle filter algorithm gives excellent performance in terms of identifying and tracking different target trajectories. This algorithm could, of course, be used for different applications and that could be done in future researches. It is not surprising that binary proximity sensor networks have attracted a lot of attention lately. Despite the minimal information a binary proximity sensor provides, networks of these sensing modalities can track all kinds of different targets classes accurate enough.