Physical soil characteristics of waterlogged and saline lands of five districts of Haryana, India

Physical characteristics of waterlogged and saline soils of five districts, namely Rohtak, Faridabad, Gurgaon, Sonipat and Jhajjar, of Haryana were studied to evaluate the aquaculture potential. The soil samples from 76 sites were procured and analysed for pH, electrical conductivity, soil particles and water retention capacity, since the knowledge of these parameters is essential for the preliminary evaluation of a site for aqua-farming. Six soil types were identified and clay-loam was observed to be the maximum at 45 (59.21%) sites, followed by silty-clay loam at 14 (18.42%), sandy-clay loam at six (7.89%), silty-loam at four (5.26%), sandy-loam at four (5.26%) and loam at three (3.94%) sites. The pH of soil indicated moderate to high alkaline conditions ranging between 8.01and 9.00 at 53 (69.73%) sites, 9.01 and 10.00 at 17 (22.36%) sites, and low between 7.01 and 8.00 at six (7.89%) sites. The electrical conductivity was found to range between <1 and 10 mmho cmˉ¹ with the value of <1.0 mmho cmˉ¹ at 36 (47.36%) sites. The water retention capacity was observed mostly to be moderate. The paper describes the interrelationship between these parameters with reference to the suitability for aqua-farming.

Experimental and theoretical comparison between static and dynamic torsional soil tests

The dynamic properties of dry Leighton Buzzard sand have been investigated using a resonant column test apparatus. These data are compared with very low frequency cyclic tests on identical specimens of sand. The comparison indicates that the properties of dry sand are independent of frequency. A simple one-dimensional model of kinematic hardening plasticity is used to predict the dynamic behaviour of the sand. The input parameters for this model are based on the results of static tests. These may be conducted on standard laboratory equipment with only minor modifications. The predictions are in good agreement with the measured data.

The modelling of soil plasticity

The modeling of the soil plasticity was discussed and it was shown that the grain breakage is an important factor of the plastic soil behaviour. A reduction of internal coefficient of friction was observed when stress-level was increased. The yield paths of all stress path tests determined by curve fitting were presented.

Ground vibration generated by trains in underground tunnels

A popular method used to reduce vibration transmitted from underground railways into nearby buildings is floating-slab track, whereby a concrete slab supporting the two rails is mounted on rubber bearings or steel springs to isolate it from the tunnel invert. This paper adds a track model to a previously developed three-dimensional tunnel model in order to assess the effectiveness of floating-slab track. A slab beam coupled to the tunnel in the wavenumber domain, with the slab bearings represented by an elastic layer, is examined first. A second beam representing the two rails together is then coupled to the slab, and axle masses representing a train are added to the rail beam. Power-spectral densities and RMS levels of soil vibration due to random roughness-displacement excitation between the masses and the rail beam are calculated. Analytical techniques are used to minimise the computational requirements of the model. The results demonstrate the inadequacy of simple mass-spring and Winkler-beam models with rigid foundations for the assessment of the vibration-isolation performance of railway track. They suggest that the achievable insertion loss is modest and that floating the track slab may in fact cause increased transmission of vibration under certain conditions. © 2006 Elsevier Ltd. All rights reserved.

Soil conditioning under London

The CTRL Contract 220 covered 7.5km twin-bore tunnels excavated between late 2002 and early 2004 from Stratford Box to St Pancras station in Central London. To ensure efficient machine operation as well as the transport and disposal of soil, soil conditioning treatments were applied. Specifically, the foam injection ratio (FIR) and the polymer injection ratio (PIR) (injected volume of foam and polymer solution expressed as a percentage of the excavated soil volume) were employed. It was found that carefully selected soil conditioning allowed chamber pressures of 200kPa or more to be accurately controlled in the stiff London Clay and to an extent, in the very stiff clays of the Lambeth Group. Average FIRs of 50% and PIRs of 7 and 9% were used in the Thanet Sand and in the Lambeth Group Clays. In contrast, much lower quantities of foam were used in the London Clay.

Dem analysis of soil-pipeline interaction in sand under lateral and upward movements at deep embedment

The soil-pipeline interactions under lateral and upward pipe movements in sand are investigated using DEM analysis. The simulations are performed for both medium and dense sand conditions at different embedment ratios of up to 60. The comparison of peak dimensionless forces from the DEM and earlier FEM analyses shows that, for medium sand, both methods show similar peak dimensionless forces. For dense sand, the DEM analysis gives more gradual transition of shallow to deep failure mechanisms than the FEM analysis and the peak dimensionless forces at very deep depth are higher in the DEM analysis than in the FEM analysis. Comparison of the deformation mechanism suggests that this is due to the differences in soil movements around the pipe associated with its particulate nature. The DEM analysis provides supplementary data of the soil-pipeline interaction in sand at deep embedment condition.

Modelling effects of axial load on behaviour of pile groups in laterally-spreading soil

Previous research into the behaviour of piled foundations in laterally-spreading soil deposits has concentrated on pile groups that carry small or negligible axial loads. This paper presents dynamic centrifuge test results for 2 x 2 pile groups with bending and geometric properties similar to real 0.5 m diameter tubular steel and solid circular reinforced-concrete field piles. Axial loads applied represented upper-bounds on typical working loads. The simultaneous scaling of the relevant properties controlling both lateral and axial behaviour allows comparisons to be drawn regarding the particular mechanisms of failure that would dominate for each type of pile. Flexible reinforced-concrete piles which tend to carry lower loads were found to be dominated by lateral effects, while steel piles, which are much stiffer and usually carry greater loads are dominated by settlement considerations. © 2006 Taylor & Francis Group.

Cementation liquefaction remediation for existing buildings

Many typical liquefaction remediation techniques are not appropriate for application under existing buildings and more novel techniques are required. This paper describes centrifuge tests investigating the performance of cementation as a liquefaction remediation method. Two soil profiles with the same superstructure were tested under earthquake shaking. The first profile consisted of a deep layer of loose, liquefiable sand. The second comprised a shallow layer of loose sand overlying dense sand. Centrifuge tests were carried out with a cemented zone underneath the structure, through the full depth of the liquefiable layers and also partial depth. The superstructure was modelled as a single-degree-offreedom system. It is found that a cemented zone through the full depth of a liquefiable layer results in considerable reduction of structural settlements. Increased magnitude and higher frequency accelerations are transmitted to the structure but, depending on the building characteristics, it is likely that improved overall seismic performance can be achieved. Improvements in structural settlements can also be obtained with partialdepth remediation, if the depth of the cemented zone is greater than the depth of liquefaction. This type of remediation seems to have little effect on the accelerations transmitted to the structure.

Sustainable binders for soil stabilisation

Portland cement is the most commonly and widely used binder in ground improvement soil stabilisation applications. However, many changes are now affecting the selection and application of stabilisation additives. These include the significant environmental impacts of Portland cement, increased use of industrial by-products and their variability, increased range of application of binders and the development of alternative cements and novel additives with enhanced environmental and technical performance. This paper presents results from a number of research projects on the application of a number of Portland cement-blended binders, which offer sustainability advantages over Portland cement alone, in soil stabilisation. The blend materials included ground granulated blastfurnace slag, pulverised fuel ash, cement kiln dust, zeolite and reactive magnesia and stabilised soils, ranging from sand and gravel to clay, and were assessed based on their mechanical performance and durability. The results are presented in terms of strength and durability enhancements offered by those blended binders.

Chryseobacterium flavum sp nov., isolated from polluted soil

A Gram-negative, non-motile, rod-shaped bacterial strain, designated CW-E 2(T), was isolated from a polluted soil sample collected from Jiangsu Province, China. A taxonomic study of the isolate, including phylogenetic analysis based on 16S rRNA gene seque

Pontibacter akesuensis sp nov., isolated from a desert soil in China

A Gram-negative, non-motile, rod-shaped bacterium, designated strain AKS 1 T, was isolated from a desert soil sample collected from Alkesu, Xin.lang Province, China. A taxonomic study, including phylogenetic analysis based on 16S rRNA gene sequences and p