Performance, carcass traits, meat quality and economic analysis of feedlot of young bulls fed oilseeds with and without supplementation of vitamin E

The objective of this research was to evaluate average daily gain (ADG), carcass traits, meat tenderness and profitability of keeping cattle fed different oilseeds and vitamin E in feedlot. A total of 40 Red Norte young bulls with initial average body weight of 339±15 kg were utilized. The experimental design was completely randomized in a 2 × 2 factorial arrangement. The experiment lasted 84 days and experimental diets presented soybeans or cottonseeds as lipid sources associated or not to daily supplementation of 2,500 UI vitamin E per animal. The concentrate:roughage ratio was 60:40. Diets had the same amount of nitrogen (13% CP) and ether extract (6.5%). The data were analyzed by means of statistical software SAS 9.1. Neither vitamin supplementation nor lipid source affected ADG. There was no interaction between lipid source and vitamin supplementation for the variables studied. The inclusion of cottonseed reduced the carcass yield. There was no effect of diets on hot and cold carcass weights or prime cuts. The inclusion of cottonseed reduced the backfat thickness. No effect of experimental diets on the rib-eye area was observed. There was no effect of lipid source or vitamin supplementation on meat tenderness, which was affected, however, by ageing time. Diets with soybeans presented higher cost per animal. The utilization of soybean implied reduction of the gross margin (R$ 59.17 and R$ 60.51 for diets based on soy with and without supplemental vitamin, respectively, vs. R$ 176.42 and R$ 131.79 for diets based on cottonseed). The utilization of cottonseed enables improvement of profitability of feedlot fattening, in spite of negatively affecting some carcass characteristics.

Isolation and HPLC quantitative analysis of flavonoid glycosides from Brazilian beverages (Maytenus ilicifolia and M-aquifolium)

Aqueous infusions of Brazilian Maytenus leaves are used as beverages, foodstuffs, and phytomedicines. Previously, we isolated two new flavonoid tetrasaccharides from the infusion of Maytenus aquifolium leaves that showed antiulcer activity. In this investigation a new flavonoid tetrasaccharide, kaempferol-3-O-alpha -L-rhamnopyranosyl (1-6)-O-[alpha -L-arabinopyranosyl (1 -->3)-O-alpha -L-rhamnopyranosyl (1-2)]-O-beta -D-galactopyranoside (3), was isolated, together with kaempferol tri- and disaccharides and quercetin trisaccharides from the aqueous infusion of Maytenus ilicifolia leaves. All structures were elucidated by ES-MS and NMR spectroscopic methods. The quantitative analysis of the flavonoid glycosides from Maytenus ilicifolia and M. aquifolium has been performed by HPLC.

Strong and fast phase modulation for quantitative analysis of photorefractive gratings

A new approach for studying photorefractive gratings in two-wave mixing experiments by a phase modulation technique is presented. The introduction of a large-amplitude, high-frequency sinusoidal phase modulation in one of the input beams blurs the interference pattern and provides powerful harmonic signals for accurate measurements of the grating diffraction efficiency eta and the output phase shift rho between the transmitted and diffracted waves. The blurring of the light fringes can be used to suppress the higher spatial harmonics of the grating, allowing a space-charge field with sinusoidal profile to be recorded. Although the presence of such a strong phase modulation affects the beam coupling in a rather complicated way, it is shown that for the special case of equal intensity input beams, the effect of the phase modulation on eta and rho is reduced to a weakening of the coupling strength. The potentialities of the technique are illustrated in a study of refractive-index waves excited by running interference patterns in a Bi12TiO20 crystal. Expressions for the diffraction efficiency and the output phase shift are derived and used to match numerically calculated curves to the experimental data. The theoretical model is supported by the very good data fitting and allows the computation of important material parameters.

Quantitative analysis of mineral content in enamel using laboratory microtomography and microhardness analysis. - art. no. 631823

This study evaluates laboratory microtomography and microhardness analysis for quantifying the mineral content of bovine enamel. Fifty enamel blocks were submitted individually for 5 days to a pH-cycling model at 37 degrees C and remained in the remineralizing solution for 2 days. The blocks were treated twice daily for 1 min with NaF dentifrices (Placebo, 275, 550, 1,100 mu g F/g and Crest (R)) diluted in deionized water. Surface microhardness changes (%SMH) and mineral loss (Delta Z) were then calculated. Laboratory microtomography was also used to measure total mineral lost (LMM). Pearson's correlation (p < 0.05) was used to determine the relationship between different methods of analysis and dose-response between treatments. Dentifrice fluoride concentration and %SMH and Delta Z were correlated (p < 0.05). There was a positive relationship (p < 0.05) when comparing LMM vs. Delta Z; a negative relationship (p < 0.05) was found for %SMH vs. LMM and %SMH vs. Delta Z. Therefore, both mineral quantification techniques provide adequate precision for studying the bovine enamel-pH-cycling demineralization/remineralization model.

Topographical, diametral, and quantitative analysis of dentin tubules in the root canals of human and bovine teeth

The aim of this study was to evaluate the number and the diameter of dentin tubules in root canals, in the cervical, middle, and apical thirds, of human and bovine teeth. Twenty-four single-rooted, human premolars were divided into four groups (n = 6): GH1, 10 to 15 years; GH2, 16 to 30 years; GH3, 31 to 45 years; and GH4, 46 to 80 years; and 24 bovine incisors were divided into four groups (n = 6): GB1, central; GB2, lateral first; GB3, lateral second; and GB4, lateral third. The crowns were removed from the specimens, which were then debrided, sectioned longitudinally in the vestibular-lingual direction, and submitted to ultrasonic cleaning. Scanning electron microscopic evaluations were made with 1,000x and 5,000x magnification. According to the root thirds, statistically significant differences were found both for the number and the diameter of dentin tubules, with the cervical third presenting the highest mean values for both specimen types. As regards the number of dentin tubules, it was observed that the bovine specimens presented a significantly higher mean value than the human specimens; this difference was not observed when the diameters of the two types were compared.

Dielectric thermal analysis as a tool for quantitative-evaluation of the viscosity and the kinetics of epoxy resin cure

Dielectric thermal analysis has been proved as a valuable tool for monitoring the epoxy curing process and the related rheological properties in the fabrication of polymer-matrix composite materials. This technique also has the potential to be applied in the monitoring of magnet impregnation processes as well as in quality control. In this work we present the quantitative evaluation of the viscosity changing and the curing kinetics for a commercial Stycast epoxy resin system at different temperatures through the impedance analysis. The results showed correlation between the real component of the complex impedance and the isothermal reaction extent. Comparing the dielectric analysis result with the viscosity measured by rotational rheometer we observed a similar behavior reported for dynamic mechanic analysis. The results comparison have shown that the kinetics parameters obtained from DSC and DETA analysis showed different sensitivities related to the characteristics of curing stages. We concluded that the dielectric thermal analysis should be applied in quantitative evaluation of cure kinetics.

Quantitative analysis of mineral content in enamel using synchrotron microtomography and microhardness analysis. - art. no. 631824

Synchrotron microtomography is a tool to quantify the mineralization of dental tissues as well as microhardness analysis, since they provide adequate precision and contrast sensitivity. This study evaluates synchrotron microtomography and microhardness analysis for quantifying the mineral content of bovine enamel. Fifty enamel blocks were submitted individually for 5 days to a pH-cycling model at 37 degrees C and remained in the remineralizing solution for 2 days. The blocks were treated twice daily for 1 min with NaF dentifrices (Placebo, 275, 550, 1,100 mu g F/g and Crest (R)) diluted in deionized water. Surface microhardness changes (%SMH) and mineral loss (Delta Z) were then calculated. Synchrotron microtomography was also used to measure total mineral lost (SMM). Pearson's correlation (p < 0.05) was used to determine the relationship between different methods of analysis and dose-response between treatments. Dentifrice fluoride concentration and %SMH and Delta Z were correlated (p < 0.05). There was a positive relationship (p < 0.05) when comparing SMM vs. Delta Z; a negative relationship (p < 0.05) was found for %SMH vs. SMM and %SMH vs. Delta Z. Based on the results of this study, it was possible to conclude that synchrotron microtomography provides the best spatial resolution and contrast sensitivity for quantifying mineral gradients.

Thermogravimetry on calcined mass basis - hydrated cement phases and pozzolanic activity quantitative analysis

When cement hydrated compositions are analyzed by usual initial mass basis TG curves to calculate mass losses, the higher is the amount of additive added or is the combined water content, the higher is the cement 'dilution' in the initial mass of the sample. In such cases, smaller mass changes in the different mass loss steps are obtained, due to the actual smaller content of cement in the initial mass compositions. To have a same mass basis of comparison, and to avoid erroneous results of initial components content there from, thermal analysis data and curves have to be transformed on cement calcined basis, i.e. on the basis of cement oxides mass present in the calcined samples or on the sample cement initial mass basis.The paper shows and discusses the fundamentals of these bases of calculation, with examples on free and combined water analysis, on calcium sulfate hydration during false cement set and on quantitative evaluation and comparison of pozzolanic materials activity.

Quantitative analysis of AgNOR proteins in exfoliative cytology specimens of oral mucosa from smokers and nonsmokers

OBJECTIVE: To determine the cell proliferation rate and possible effects of cigarette smoking on the oral mucosa lining through analysis of silver-stained nucleolar organizer regions (AgNORs) in exfoliative cytology specimens.STUDY DESIGN: Exfoliative cytology was performed on the left side of the border of the tongue and of the floor of the mouth in 25 smoking patients and 25 nonsmoking patients. The inclusion criterion for smokers was the consumption of more than 20 cigarettes per day for a minimum of 30 years.RESULTS: The slides were stained by histochemical AgNOR method. In the nonsmoking group the mean number of AgNORs per nucleus was 2.732 +/- 0.236 in the tongue border and 2.918 +/- 0.195 in the floor of the mouth. In smoking patients the mean number of AgNORs per nucleus was 3.372 +/- 0.375 in the tongue border and 3.245 +/- 0.237 in the floor of the mouth.CONCLUSION. The results suggest higher cell proliferation quantified by the histochemical AgNOR technique in exfoliative cytology specimens obtained from the oral mucosa lining of smokers presenting no clinical alterations.

Genetic correlations between categorical morphological traits in Nelore cattle by applying Bayesian analysis under a threshold animal model

P>In this study, Bayesian analysis under a threshold animal model was used to estimate genetic correlations between morphological traits (body structure, finishing precocity and muscling) in Nelore cattle evaluated at weaning and yearling. Visual scores obtained from 7651 Nelore cattle at weaning and from 4155 animals at yearling, belonging to the Brazilian Nelore Program, were used. Genetic parameters for the morphological traits were estimated by two-trait Bayesian analysis under a threshold animal model. The genetic correlations between the morphological traits evaluated at two ages of the animal (weaning and yearling) were positive and high for body structure (0.91), finishing precocity (0.96) and muscling (0.94). These results indicate that the traits are mainly determined by the same set of genes of additive action and that direct selection at weaning will also result in genetic progress for the same traits at yearling. Thus, selection of the best genotypes during only one phase of life of the animal is suggested. However, genetic differences between morphological traits were better detected during the growth phase to yearling. Direct selection for body structure, finishing precocity and muscling at only one age, preferentially at yearling, is recommended as genetic differences between traits can be detected at this age.