Growth and compaction behaviour of copper concentrate granules in a rotating drum

In order to understand the growth and compaction behaviour of chalcopyrite (copper concentrate), batch granulation tests were carried out using a rotating drum. The granule growth exhibited induction-type behaviour, as defined by Iveson and Litster [AIChE J. 44 (1998) 15 10]. There were two consecutive stages during granulation: the induction stage, during which the granules are gradually being compacted and little or no growth occurs, and the rapid growth stage, which starts when the granules have become surface wet and are rapidly growing. In agreement with earlier findings. an increased amount of binder liquid shortened the induction time. The compaction behaviour was also investigated. A displaced volume method was adopted to determine the porosity of the granules. It was shown that this technique had a limitation as it was unable to detect the reduction of the volumes of the granule pores after the granules had become surface wet. Due to this, some of the measurements were not suited for fitting a three-parameter empirical model. Attempts were made to determine whether the rapid growth stage started with the pore saturation exceeding a certain critical value, but due to the scatter in the porosity measurements and the fact that some of the measurements could not be used, it was not possible to determine a critical pore saturation, However, the porosity measurements clearly demonstrated that the porosity of the granules decreased during the induction stage of an experiment and that when rapid growth occurred, the granules had a pore saturation was around 0.85. This value was slightly lower than unity, which is most likely due to trapped air bubbles. (C) 2002 Published by Elsevier Science B.V.

Review and future directions in the modelling and control of continuous drum granulation

Many granulation plants operate well below design capacity, suffering from high recycle rates and even periodic instabilities. This behaviour cannot be fully predicted using the present models. The main objective of the paper is to provide an overview of the current status of model development for granulation processes and suggest future directions for research and development. The end-use of the models is focused on the optimal design and control of granulation plants using the improved predictions of process dynamics. The development of novel models involving mechanistically based structural switching methods is proposed in the paper. A number of guidelines are proposed for the selection of control relevant model structures. (C) 2002 Published by Elsevier Science B.V.

Structural ordering of coal char during heat treatment and its impact on reactivity

The effect of heat treatment on the structure of an Australian semi-anthracite char was studied in detail in the 850-1150degreesC temperature range using XRD, HRTEM, and electrical resistivity techniques. It was found that the carbon crystallite size in the char does not change significantly during heat treatment in the temperature range studied, for both the raw coal and its ash-free derivative obtained by acid treatment. However, the fraction of the organized carbon in the raw coal chars, determined by XRD, increased with increase of heat treatment time and temperature, while that for the ash-free coal chars remained almost unchanged. This suggests the occurrence of catalytic ordering during heat treatment, supported by the observation that the electrical resistivity of the raw coal chars decreased with heat treatment, while that of the ash-free coal chars did not vary significantly. Further confirmatory evidence was provided by high resolution transmission electron micrographs depicting well-organized carbon layers surrounding iron particles. It is also found that the fraction of organized carbon does not reach unity, but attains an apparent equilibrium value that increases with increase in temperature, providing an apparent heat of ordering of 71.7 kJ mol(-1) in the temperature range studied. Good temperature-independent correlation was found between the electrical resistivity and the organized carbon fraction, indicating that electrical resistivity is indeed structure sensitive. Good correlation was also found between the electrical resistivity and the reactivity of coal char. All these results strongly suggest that the thermal deactivation is the result of a crystallite-perfecting process, which is effectively catalyzed by the inorganic matter in the coal char. Based on kinetic interpretation of the data it is concluded that the process is diffusion controlled, most likely involving transport of iron in the inter-crystallite nanospaces in the temperature range studied. The activation energy of this transport process is found to be very low, at about 11.8 kJ mol(-1), which is corroborated by model-free correlation of the temporal variation of organized carbon fraction as well as electrical resistivity data using the superposition method, and is suggestive of surface transport of iron. (C) 2002 Elsevier Science Ltd. All rights reserved.

A quantitative state and transition model for the Mitchell grasslands of central western Queensland

Concerns of reduced productivity and land degradation in the Mitchell grasslands of central western Queensland were addressed through a range monitoring program to interpret condition and trend. Botanical and eclaphic parameters were recorded along piosphere and grazing gradients, and across fenceline impact areas, to maximise changes resulting from grazing. The Degradation Gradient Method was used in conjunction with State and Transition Models to develop models of rangeland dynamics and condition. States were found to be ordered along a degradation gradient, indicator species developed according to rainfall trends and transitions determined from field data and available literature. Astrebla spp. abundance declined with declining range condition and increasing grazing pressure, while annual grasses and forbs increased in dominance under poor range condition. Soil erosion increased and litter decreased with decreasing range condition. An approach to quantitatively define states within a variable rainfall environment based upon a time-series ordination analysis is described. The derived model could provide the interpretive framework necessary to integrate on-ground monitoring, remote sensing and geographic information systems to trace states and transitions at the paddock scale. However, further work is needed to determine the full catalogue of states and transitions and to refine the model for application at the paddock scale.

Using the flexibility index to compare batch and continuous activated sludge processes

This paper considers the question of which is better: the batch or the continuous activated sludge processes? It is an important question because dissension still exists in the wastewater industry as to the relative merits of each of the processes. A review of perceived differences in the processes from the point of view of two related disciplines, process engineering and biotechnology, is presented together with the results of previous comparative studies. These reviews highlight possible areas where more understanding is required. This is provided in the paper by application of the flexibility index to two case studies. The flexibility index is a useful process design tool that measures the ability of the process to cope with long term changes in operation.

A comprehensive insight into floc characteristics and their impact on compressibility and settleability of activated sludge

This paper presents a comprehensive study of sludge floc characteristics and their impact on compressibility and settleability of activated sludge in full scale wastewater treatment processes. The sludge flocs were characterised by morphological (floc size distribution, fractal dimension, filament index), physical (flocculating ability, viscosity, hydrophobicity and surface charge) and chemical (polymeric constituents and metal content) parameters. Compressibility and settleability were defined in terms of the sludge volume index (SVI) and zone settling velocity (ZSV). The floc morphological and physical properties had important influence on the sludge compressibility and settleability. Sludges containing large flocs and high quantities of filaments, corresponding to lower values of fractal dimension (D-f), demonstrated poor compressibility and settleability. Sludge flocs with high flocculating ability had lower SVI and higher ZSV, whereas high values of hydrophobicity, negative surface charge and viscosity of the sludge flocs correlated to high SVI and low ZSV. The quantity of the polymeric compounds protein. humic substances and carbohydrate in the sludge and the extracted extracellular polymeric substances (EPS) had significant positive correlations with SVI. The ZSV was quantitatively independent of the polymeric constituents. High concentrations of the extracted EPS were related to poor compressibility and settleability. The cationic ions Ca, Mg, Al and Fe in the sludge improved significantly the sludge compressibility and settleability. (C) 2003 Elsevier Science B.V. All rights reserved.

Nitrification of high strength ammonia wastewtaer treatment - process selection is the major factor.

Biological nitrogen removal via the nitrite pathway in wastewater treatment is very important in Saving the cost of aeration and as an electron donor for denitrification. Wastewater nitrification and nitrite accumulation were carried out in a biofilm airlift reactor with autotrophic nitrifying biofilm. The biofilm reactor showed almost complete nitrification and most of the oxidized ammonium was present as nitrite at the ammonium load of 1.5 to 3.5 kg N/m3.d. Nitrite accumulation was stably achieved by the selective inhibition of nitrite oxidizers with free ammonia and dissolved oxygen limitation. Stable 100% conversion to nitrite could also be achieved even under the absence of free ammonia inhibition on nitrite oxidizers. Batch ammonium oxidation and nitrite oxidation with nitrite accumulating nitrifying biofilm showed that nitrite Oxidation was completely inhibited when free ammonia is higher than 0.2 mg N/L. However, nitrite oxidation activity was recovered as soon as the free ammonia concentration was below the threshold level when dissolved oxygen concentration was not the limiting factor. Fluorescence in situ hybridization analysis of cryosectioned nitrite accumulating nitrifying biofilm showed that the β-subclass of Proteobacteria, where ammonia oxidizers belong, was distributed outside the biofilm whereas the α-subclass of Proteobacteria, where nitrite oxidizers belong, was found mainly in the inner part of the biofilm. It is likely that dissolved oxygen deficiency or limitation in the inner part of the nitrifying biofilm, where nitrite oxidizers exist, is responsible for the complete shut down of the nitrite oxidizers activity under the absence of free ammonia inhibition.

Prediction of multilayer adsorption and capillary condensation phenomena in cylindrical mesopores

MCM-41 periodic mesoporous silicates with a high degree of structural ordering are synthesized and used as model adsorbents to study the isotherm prediction of nitrogen adsorption. The nitrogen adsorption isotherm at 77 K for a macroporous silica is measured and used in high-resolution alpha(s)-plot comparative analysis to determine the external surface area, total surface area and primary mesopore volume of the MCM-41 materials. Adsorption equilibrium data of nitrogen on the different pore size MCM-41 samples (pore diameters from 2.40 to 4.92 nm) are also obtained. Based on the Broekhoff and de Boer' thermodynamic analysis, the nitrogen adsorption isotherms for the different pore size MCM-41 samples are interpreted using a novel strategy, in which the parameters of an empirical expression, used to represent the potential of interaction between the adsorbate and adsorbent, are obtained by fitting only the multilayer region prior to capillary condensation for C-16 MCM-41. Subsequently the entire isotherm, including the phase transition, is predicted for all the different pore size MCM-41 samples without any fitting. The results show that the prediction of multilayer adsorption and total adsorbed amount are in good agreement with the experimental isotherms. The predictions of the relative pressure corresponding to capillary equilibrium (coexistence) transition agree remarkably with experimental data on the adsorption branch even for hysteretic isotherms, confirming that this is the branch appropriate for pore size distribution analysis. The impact of pore radius on the adsorption film thickness and capillary coexistence pressure is also investigated, and found to agree with the experimental data. (C) 2003 Elsevier Inc. All rights reserved.

Fatores intervenientes na implementação de ações estratégicas para a promoção do selo de indicação geográfica das panelas de barro de goiabeiras

Visando a proteção da propriedade industrial advinda de uma região demarcada, surgiu a Indicação Geográfica (IG). O registro da IG é conferido aos produtos ou serviços característicos de seu local de origem, apresentando qualidades únicas em função dos recursos naturais. Além disso, a IG é responsável por distinguir estes produtos em relação aos disponíveis no mercado. Neste contexto, entidades como Sebrae, MAPA e INPI, têm promovido ações estratégicas com o objetivo de apoiar a proteção do saber fazer e consequentemente, os produtos tradicionais das regiões. Tais entidades são responsáveis por promover a sustentabilidade do processo juntos aos produtores, assim como disseminar o selo para os consumidores. Assim, iniciativas como esta precisam ser apoiadas a fim de entregar resultados significativos para o desenvolvimento das regiões e seus respectivos produtos com o selo de IG. O Plano de Apoio à Gestão da Indicação Geográfica desenvolvido pelo Sebrae/ES tem três pilares: melhoria do processo de produção, promoção do produto e a sustentabilidade do processo. A presente pesquisa, baseando-se nas teorias sobre estratégia e implementação de estratégias, analisa os fatores intervenientes que contribuem para o sucesso da implementação do Plano de Apoio à Gestão da indicação geográfica das Panelas de Barro de Goiabeiras, bairro do município de Vitória, capital do Espírito Santo. A pesquisa é um estudo de caso de natureza qualitativa, exploratória e descritiva ex-post-facto. Os dados foram coletados nos documentos (plano de ação do Sebrae/ES, Livro dos Saberes e relatórios desenvolvidos por consultores especializados) e por meio de entrevistas com seis agentes de políticas públicas e cinco paneleiras, envolvidos na elaboração e implementação do plano de ação. Para a análise dos dados, adotou-se a metodologia de análise de conteúdo com index definido a posteriori. Do Plano de Apoio à Gestão da IG das Paneleiras de Goiabeiras, foram agrupadas três ações estratégicas buscando identificar em que medida os fatores intervenientes afetaram a implementação de cada ação estudada: Ação1: fortalecimento dos aspectos culturais do produto, Ação 2: fortalecimento dos aspectos sociais do produto e Ação 3: fortalecimento dos aspectos econômicos associados à diferenciação por IG. Os resultados mostraram que na Ação 1 o fator interveniente liderança superou as expectativas na implementação das estratégias. Já os aspectos políticos, o acompanhamento de resultados e a estrutura organizacional desenvolveram as ações conforme o planejado, enquanto os fatores intervenientes cultura e clareza nas estratégias apresentaram oportunidades de melhorias. Na Ação 2 somente os fatores intervenientes recursos, cultura e clareza nas estratégias apresentaram-se de acordo com o proposto, enquanto a liderança e a estrutura organizacional mostraram-se como pontos de oportunidades de melhoria. Por fim, na Ação 3 nenhum fator interveniente foi destaque como uma oportunidade de melhoria. A estrutura organizacional e os aspectos políticos apresentaram-se de acordo, enquanto os recursos e a liderança superaram as expectativas.

Historical and conceptual landscape of the character

This paper was developed with the intention of broadly demonstrating the complexity of the area known recently as character development, as a creative process methods and implementation. It searches the understanding of the character itself, its place in the narrative and its reception by the reader or target audience. It is a multidisciplinary tool that faces a multitude of challenges from an increasingly demanding public and with specific goals in mind, and yet it also gives us valuable insight over how we interact with one another and the world around us, teaching us how to transfer such knowledge into fiction promoting empathic bonds between the reader and the characters. The human tendency to create is limitless and as old as mankind itself, we create, recreate and reinterpret and then populate such tales with believable characters from who we learn, and experience events and tales that shape our very lives.

An optimal level of technology reliance on foreign partners in a global sourcing partnership: components procurement, technology management and market performance

Existing studies on global sourcing strategy have implicitly adopted a cJosed-systems perspective in which sourcing activities are managed within a multinational company across national boundaries. Produd and process innovations and components procurement that are jointly managed by a consortium of cooperating firms have not been examined. In this paper, we empiricallyexamine the issues concerning sourcing partnerships in an open-systems perspective. Findings suggest that even in a sourcing partnership arrangement with a foreign supplier, the principal firm's ability to procure and control the supply of major components has a positive bearing on its market performance.

Neoinstitutionalism and the appropriation of bourdieu's work: a critical assessment

Despite the still present hegemony of the structural-functionalist orthodoxy, the mid 1980's witnesses the insurgence of new philosophical approaches. This body of work had become a vital intellectual and ideological resource for those who wanted to confront the functionalist dominance in organization studies, such as structuration theory, labour process theory and neoinstitutionalist theory. The purpose of this paper is to review the incorporation of Bourdieu's work into neoinstitutionalism. I argue that this appropriation has resulted in a significant loss of theoretical strength. By giving place to the cognitivist metaphors of mental models, "scripts" and "schemas", instead of adopting the notion of habitus, neoinstitutionalism reinforces some of the ever-present dichotomies in social sciences, especially those of agency/structure and individual/society. While neoinstitutionalism was refining the cognitive approach in the 1990's, Bourdieu was moving towards psychoanalysis. Some indications for future research are provided in the concluding notes.

Interaction of formaldehyde and tobacco smoking in the frequency of micronucleus and the XRCC3 Thr241Met polymorphism

Formaldehyde is classified by IARC as carcinogenic to humans (nasopharyngeal cancer). Tobacco smoke has been epidemiologically associated to a higher risk of development of cancer, especially in the oral cavity, larynx and lungs, as these are places of direct contact with many carcinogenic tobacco’s compounds. XRCC3 is involved in homologous recombination repair of cross-links and chromosomal double-strand breaks (Thr241Met polymorphism). The aim of the study is to determine whether there is an in vivo association between genetic polymorphism of the gene XRCC3 and the frequency of genotoxicity biomarkers in subjects exposed or not to formaldehyde and with or without tobacco consumption.

RF Receiver Front End for 28.5 GHz Applications on a 70 GHz F-T SiGe BiCMOS Process

This article presents the design and test of a receiver front end aimed at LMDS applications at 28.5 GHz. It presents a system-level design after which the receiver was designed. The receiver comprises an LNA, quadrature mixer and quadrature local oscillator. Experimental results at 24 GHz center frequency show a conversion voltage gain of 15 dB and conversion noise figure of 14 5 dB. The receiver operates from a 2 5 V power supply with a total current consumption of 31 mA.