Influence of the sample area in the variability of losses in the mechanical harvesting of soybeans

The mechanical harvesting is an important stage in the production process of soybeans and, in this process; the loss of a significant number of grains is common. Despite the existence of mechanisms to monitor these losses, it is still essential to use sampling methods to quantify them. Assuming that the size of the sample area affects the reliability and variability between samples in quantifying losses, this paper aimed to analyze the variability and feasibility of using different sizes of sample area (1, 2 and 3 m²) in quantifying losses in the mechanical harvesting of soybeans. Were sampled 36 sites and the cutting losses, losses by other mechanisms of the combine and total losses were evaluated, as well as the water content in seeds, straw distribution and crop productivity. Data were subjected to statistical analysis (descriptive statistics and analysis of variance) and Statistical Control Process (SCP). The coefficients of variation were similar for the three frames available. Combine losses showed stable behavior, whereas cutting losses and total losses showed unstable behavior. The frame size did not affect the quantification and variability of losses in the mechanical harvesting of soybeans, thus a frame of 1 m² can be used for determining losses.

Mechanical properties of castor beans subject to different drying temperatures aiming to disrupt the bean coat

In castor oil extraction process, the bean coat is abrasive to the equipment and releases substances that modify the oil color, reducing its quality. A potential solution would be to run the extraction by compressing only the endosperm. Due to lack of information, the objective of this study was to evaluate the influence of forced air drying at 40, 60, 80 and 100 ºC and farmyard drying, in the mechanical properties of the beans, aiming to break the bean coat. Castor beans were subjected to compression tests, in two perpendicular directions, at a strain rate of 0.6 mm.s-1. Average values of force, deformation energy, strain, all at rupture, and stiffness were used to evaluate the effects of dehydration. It was observed that the heat treatments did not alter the mechanical properties of castor beans, the strain and stiffness values discriminate the differences between the directions and had the lowest coefficients of variation. It was concluded that forced air drying, more costly than farmyard drying, does not bring benefits to the decortication. However, regardless the heat treatment used, the mechanical stress lengthwise is the most suitable to promote decortication.

Spatial variability of mechanical resistance to penetration evaluated with mobile unit on haplic vertisol cultivated with mango

Since the advent of mechanized farming and intensive use of agricultural machinery and implements on the properties, the soil began to receive greater load of machinery traffic, which can cause increased soil compaction. The aim of this study was to evaluate the spatial variability of soil mechanical resistance to penetration (RP) in the layers of 0.00-0.10, 0.10-0.20, 0.20-0.30 and 0.30-0.40m, using geostatistics in an area cultivated with mango in Haplic Vertisol of the northeastern semi-arid, with mobile unit equipped with electronic penetrometer. The RP data was collected in 56 points from an area of 3 ha, and random soil samples were collected to determine the soil moisture and texture. For RP data analysis we used descriptive statistics and geostatistics. The soil mechanical resistance to penetration presented increased variability, with adjustment of the spherical and exponential semivariograms in the layers. We found that 42% of the area in the layer of 0.10-0.20m showed RP values above 2.70 MPa. Maximum values of RP were found in the layer of 0.19-0.27m, predominantly in 56% of the area.

Mechanical damage during harvest and loading affect orange postharvest quality

Brazil is the world’s largest orange producer; however, part of this production is lost during postharvest. This loss can be minimized by controlling incidence of physical damage throughout the harvest and loading operations. Impacts can negatively modify quantitative and qualitative fruits aspects. The main goal of this study was to measure the impact magnitude in two types of harvest (manual and detachment) and during all steps from picking into bags until loading for transport to the processing industry and additionally evaluating, in laboratory, the physico-chemical quality of the fruit subjected to various impacts, similar to those found in the field. In order to evaluate the impact magnitude, an instrumented sphere was used (760 mm, Techmark, Inc, USA). The following physico-chemical parameters were evaluated during 6-days of storage: weight loss, soluble solids contents, titratable acidity, ascorbic acid content, pH, firmness and peel color. The greatest impacts were observed during harvest, during the detachment practice, and when loading and unloading from bulk storage, with average acceleration values between 249.5 and 531.52G. The impact incidence in oranges were responsible for reducing the soluble solids, titratable acidity, ascorbic acid and weight by to 5.5%; 8.7%; 4.6% and 0.5%, respectively, compared to the control. Impacts during harvest and the various pre-industry manipulation steps must be controlled as they interfere in postharvest quality and physiology of ‘Valência’ oranges.

Quality of peanut mechanical sowing in function of seeding density and size of the seeds

ABSTRACTPeanut crop (Arachis hypogaeaL.) mechanization has been improved over the years; however there are drawbacks that affect the quality of operations. Thus, this article’s objectives were to evaluate the operational performance of the mechanized sowing of peanut crop according to seeding densities (10, 14, and 18 seeds m-1) and seed sizes (21 and 23 mm). It was observed that the seeds of 23 mm had shorter average number of days to emergence and a higher percentage of emergences, occurring the opposite to the seeding density of 18 seeds m-1. The higher the seeding density, the largest was the plant stand, whereas the 23 mm seed obtained the best results and the same with the seeding density of 14 seeds m-1 that had a higher percentage of normal spacing. The densities of 14 and 18 seeds m-1 reflected in higher yields, being always superior to the 23 mm seeds.

Monitoring of mechanical sugarcane harvesting through control charts

ABSTRACT Statistical process control in mechanized farming is a new way to assess operation quality. In this sense, we aimed to compare three statistical process control tools applied to losses in sugarcane mechanical harvesting to determine the best control chart template for this quality indicator. Losses were daily monitored in farms located within Triângulo Mineiro region, in Minas Gerais state, Brazil. They were carried over a period of 70 days in the 2014 harvest. At the end of the evaluation period, 194 samples were collected in total for each type of loss. The control charts used were individual values chart, moving average and exponentially weighted moving average. The quality indicators assessed during sugarcane harvest were the following loss types: full grinding wheel, stumps, fixed piece, whole cane, chips, loose piece and total losses. The control chart of individual values is the best option for monitoring losses in sugarcane mechanical harvesting, as it is of easier result interpretation, in comparison to the others.

Self assessment report for international accreditation - Bachelor's and Master's degree programmes in Mechanical Engineering

Itsearviointiraportissa kuvataan Lappeenrannan teknillisen yliopiston konetekniikan kandidaatin ja diplomi-insinöörin tutkinto-ohjelmat opetussuunnitelman 2011-2012 mukaisesti. Itsearviointiraportti on tuotettu saksalaisen ASIIN-akkreditointiorganisaation raportointimallin mukaisesti.

Virtuaalimallin hyödyntäminen harvesteripään tuotekehityksessä

Virtuaalimallinnuksella tarkoitetaan koneen simulointia, jossa huomioidaan koneen mekaniikka, toimilaitteet ja ohjausjärjestelmä. Työn tavoitteena oli luoda virtuaalimalli harvesteripäästä. Kyseinen virtuaalimalli sisälsi harvesteripään tärkeimmät mekaaniset osat, pituusmittalaitteen hydrauliikkapiirin ja tämän ohjauksen. Luodussa virtuaalimallissa huomioitiin myös harvesteripään ja puun väliset kontaktit. Lisäksi työssä tutkittiin mahdollista virtuaalimallinnuksen implementoimista osaksi yrityksen tuotekehitysprosessia. Työssä suoritettiin verifiointimittaukset pituusmittalaitteen hydrauliikkapiirille sekä virtuaalimallin hydrauliikkakomponentit parametrisoitiin. Mittauksista saatuja tuloksia verrattiin virtuaalimallista saatuihin tuloksiin. Työssä esitellään myös ehdotus kuinka virtuaalimallinnusta kannattaisi hyödyntää osana yrityksen tuotekehitysprosessia. Virtuaalimallin eri osa-alueilla saavutetut tulokset osoittavat, että virtuaalimallinuksen hyödyntäminen tuotekehitysprosessin aikana mahdollistaa harvesteripään toimintojen tarkastelun ennen prototyypin rakentamista ja testaamista. Lisäksi hydrauliikkapiirin parametrisoimisella pystytään tutkimaan parametrien vaikutusta kokonaisuuteen.

Temporary abdominal closure with zipper-mesh device for management of intra-abdominal sepsis

OBJECTIVE: to present our experience with scheduled reoperations in 15 patients with intra-abdominal sepsis. METHODS: we have applied a more effective technique consisting of temporary abdominal closure with a nylon mesh sheet containing a zipper. We performed reoperations in the operating room under general anesthesia at an average interval of 84 hours. The revision consisted of debridement of necrotic material and vigorous lavage of the involved peritoneal area. The mean age of patients was 38.7 years (range, 15 to 72 years); 11 patients were male, and four were female. RESULTS: forty percent of infections were due to necrotizing pancreatitis. Sixty percent were due to perforation of the intestinal viscus secondary to inflammation, vascular occlusion or trauma. We performed a total of 48 reoperations, an average of 3.2 surgeries per patient. The mesh-zipper device was left in place for an average of 13 days. An intestinal ostomy was present adjacent to the zipper in four patients and did not present a problem for patient management. Mortality was 26.6%. No fistulas resulted from this technique. When intra-abdominal disease was under control, the mesh-zipper device was removed, and the fascia was closed in all patients. In three patients, the wound was closed primarily, and in 12 it was allowed to close by secondary intent. Two patients developed hernia; one was incisional and one was in the drain incision. CONCLUSION: the planned reoperation for manual lavage and debridement of the abdomen through a nylon mesh-zipper combination was rapid, simple, and well-tolerated. It permitted effective management of severe septic peritonitis, easy wound care and primary closure of the abdominal wall.

Device model for training of laparoscopic surgical skills

The authors present a especially constructed, lightweight, collapsible, portable and low cost model device for skills training in laparoscopic.

Containment Measures in Adolescent Psychiatric Care - Focus on Mechanical Restrain

Rajoitetoimet, erityisesti sitominen, nuorisopsykiatrisessa hoitotyössä Tutkimuksen tavoitteena oli kuvata ja syventää tietoa rajoitetoimien, erityisesti sitomisen, käytöstä nuorisopsykiatrisessa vastentahtoisessa osastohoidossa. Tutkimuksen tavoitteena oli kuvata hoitajien, lääkäreiden ja potilaiden asenteita eri rajoittamiskeinoja kohtaan nuorisopsykiatrisessa osastohoidossa, kerätä tietoa yhden vuoden aikana tapahtuneiden sitomisten määrästä ja luonteesta sekä kuvata potilaiden kokemuksia sitomisesta nuorisopsykiatrisen osastohoidon aikana. Tutkimus tuottaa arvokasta tietoa korkeatasoisten sitomiskäytäntöjen kehittämiseen nuorisopsykiatrisessa osastohoidossa, sekä sitomisten määrää vähentämällä että sitomistapoja kehittämällä. Tavoitteena on parantaa sidottujen potilaiden kliinistä hoitoa. Tutkimusaineisto kerättiin suomalaisilla, pääkaupunkiseudulle sijoittuvilla, nuorisopsykiatrisilla osastoilla neljässä vaiheessa lokakuun 2009 ja huhtikuun 2012 välisenä aikana. Helsingin ja Uudenmaan sairaanhoitopiirin (HUS) nuorisopsykiatrian erikoisalan seitsemän suljetun osaston hoitohenkilökunta sekä lääkärit suhtautuivat myönteisesti rajoittamistoimenpiteisiin. Nuorisopsykiatriset potilaat suhtautuivat rajoittamistoimenpiteisiin kriittisemmin kuin henkilökunta. Nuoret suhtautuivat myönteisimmin tarvittaessa annettavaan lääkitykseen, ajoittaiseen tarkkailuun ja kulun rajoittamiseen. Vähiten hyväksytty menetelmä oli verkkosänky. Nuoret arvioivat sitomisen kolmen vähiten hyväksytyn menetelmän joukkoon. Sitomisen esiintyvyys ja pitkien sitomisten määrä olivat korkeita tutkimukseen valituissa yksiköissä. Useimmat sidotut nuoret tiesivät syyn sitomiseensa, suhtautuivat siihen ambivalentisti nähden siinä sekä hyötyä että haittaa, pitäen sitä kuitenkin rangaistuksena. Huolimatta tästä, suurin osa haastatelluista nuorista koki, että joissain tilanteissa sitomista tarvitaan nuorisopsykiatrisessa osastohoidossa. Nuorilla oli monia ehdotuksia, kuinka parantaa sitomista käytännön osastohoidossa. Tämä väitöskirja tuottaa uutta tietoa eri rajoittamistoimenpiteiden ja sitomisen toteuttamisesta nuorisopsykiatrisessa osastohoidossa. Käytännön hoitotyön parantamiseksi nuorisopsykiatrisilla osastoilla tarvitaan laaja-alaista ja syvälle luotaavaa koulutusta, jotta rajoittamis-toimenpiteiden määrää voidaan vähentää. Myös kriisitilanteiden hallintaan tarvitaan uusia keinoja. Tietoa, kuvausta toimenpiteistä ja tilanteiden käsittelyä jälkikäteen tulee tarjota ala-ikäiselle potilaalle hänen kehitystasonsa huomioiden. Sitomisten määrää tulee vähentää ja niiden kestoa lyhentää. Nuorten tulee olla aktiivisesti mukana kehittämässä aggression hallintamenetelmiä suomalaisessa nuorisopsykiatrisessa osastohoidossa.

Microstructural and environmental effects on the mechanical properties of porous particle-polymer composites

Papper kan anses vara ett av de mest använda materialen i det dagliga livet. Tidskrifter, tidningar, böcker och diverse förpackningar är några exempel på pappersbaserade produkter. Papperets egenskaper måste anpassas till användningsändamålet. En tidskrift kräver t.ex. hög ljushet, opacitet och en slät yta hos papperet, medan dessa egenskaper är mindre viktiga för en dagstidning. Allt tryckpapper behöver vissa mekaniska egenskaper för att tåla vidarebearbetning såsom kalandrering, tryckning och vikning. Man kan bestryka papper för att förbättra dess optiska egenskaper och tryckbarhetsegenskaper. Vid bestrykning appliceras en dispersion av mineralpigment och polymerbindemedel som ett tunt lager på papperets yta. Bestrykningsskiktet kan ses som ett komplext, poröst kompositmaterial som även bidrar till papperets mekaniska egenskaper och dess processerbarhet i diverse konverteringsoperationer. Kravet på framställning av förmånligt papper med tillräckliga styrkeegenskaper ställer allt högre krav på optimeringen av pappersbestrykningsskiktets egenskaper och produktionskostnader. Målet med detta arbete var att förstå sambandet mellan pigmentbestrykningsskiktets mikrostruktur och dess makroskopiska, mekaniska egenskaper. Resultaten visar att adhesionen i gränsytan mellan pigment och bindemedel är kritisk för bestrykningsskiktets förmåga att bära mekanisk belastning. Polära vätskor är vanliga i tryckfärger och kan, eftersom de påverkar syra/bas-interaktionerna mellan pigment och latexbindemedel, försvaga denna adhesion. Resultaten tyder på att ytstyrkan hos bestruket papper kan höjas genom användning av bifunktionella dispergeringsmedel för mineralpigment. Detta medför inbesparingar i pappersproduktionen eftersom mängden bindemedel, den dyraste komponenten i bestrykningsskiktet, kan minskas.

Research and development of III-V semiconductor surfaces for improved device interfaces

This thesis is devoted to understanding and improving technologically important III-V compound semiconductor (e.g. GaAs, InAs, and InSb) surfaces and interfaces for devices. The surfaces and interfaces of crystalline III-V materials have a crucial role in the operation of field-effect-transistors (FET) and highefficiency solar-cells, for instance. However, the surfaces are also the most defective part of the semiconductor material and it is essential to decrease the amount of harmful surface or interface defects for the next-generation III-V semiconductor device applications. Any improvement in the crystal ordering at the semiconductor surface reduces the amount of defects and increases the material homogeneity. This is becoming more and more important when the semiconductor device structures decrease to atomic-scale dimensions. Toward that target, the effects of different adsorbates (i.e., Sn, In, and O) on the III-V surface structures and properties have been investigated in this work. Furthermore, novel thin-films have been synthesized, which show beneficial properties regarding the passivation of the reactive III-V surfaces. The work comprises ultra-high-vacuum (UHV) environment for the controlled fabrication of atomically ordered III-V(100) surfaces. The surface sensitive experimental methods [low energy electron diffraction (LEED), scanning tunneling microscopy/spectroscopy (STM/STS), and synchrotron radiation photoelectron spectroscopy (SRPES)] and computational density-functionaltheory (DFT) calculations are utilized for elucidating the atomic and electronic properties of the crucial III-V surfaces. The basic research results are also transferred to actual device tests by fabricating metal-oxide-semiconductor capacitors and utilizing the interface sensitive measurement techniques [capacitance voltage (CV) profiling, and photoluminescence (PL) spectroscopy] for the characterization. This part of the thesis includes the instrumentation of home-made UHV-compatible atomic-layer-deposition (ALD) reactor for growing good quality insulator layers. The results of this thesis elucidate the atomic structures of technologically promising Sn- and In-stabilized III-V compound semiconductor surfaces. It is shown that the Sn adsorbate induces an atomic structure with (1×2)/(1×4) surface symmetry which is characterized by Sn-group III dimers. Furthermore, the stability of peculiar ζa structure is demonstrated for the GaAs(100)-In surface. The beneficial effects of these surface structures regarding the crucial III-V oxide interface are demonstrated. Namely, it is found that it is possible to passivate the III-V surface by a careful atomic-scale engineering of the III-V surface prior to the gate-dielectric deposition. The thin (1×2)/(1×4)-Sn layer is found to catalyze the removal of harmful amorphous III-V oxides. Also, novel crystalline III-V-oxide structures are synthesized and it is shown that these structures improve the device characteristics. The finding of crystalline oxide structures is exploited by solving the atomic structure of InSb(100)(1×2) and elucidating the electronic structure of oxidized InSb(100) for the first time.

Critical aspects on the behavior of material from the mechanical tool-workpiece interaction in single point diamond turning

Some material aspects such as grain size, purity and anisotropy exert an important influence on surface quality, especially in single point diamond turning. The aim of this paper is to present and discuss some critical factors that can limit the accuracy of ultraprecision machining of non-ferrous metals and to identify the effects of them on the cutting mechanism with single point diamond tools. This will be carried out through observations of machined surfaces and chips produced using optical and scanning electron microscopy. Solutions to reduce the influence of some of these limiting factors related with the mechanism of generation of mirror-like surfaces will be discussed.