Alternative Flexible Overlays, HR-229, Construction Report, 1983

The object of this research project is to construct and evaluate several bituminous concrete base overlays with various high penetration bituminous products which have the potential to reduce future maintenance and construction costs. In September of 1981 nine different bituminous test sections were constructed on Osceola County roads A-34 and A-46 east of Ashton. Asphalt binders used were AC-5 asphalt cement, SC-800 liquid asphalt, MC-3000 cutback asphalt, CSS-1 emulsion and HFMS-2 emulsion. Aggregate for four of the test sections consisted of salvaged bituminous pavement and new aggregate combined. Each section was road mixed using a different binder arid placed 2-1/4" thick with a motor patrol. The other five test sections consisted of an AC-5 Type B asphalt concrete control section and four plant-mixed, cold-laid bituminous concrete overlay sections using new aggregate. The material was mixed in a continuous drum mix plant and laid with a full width paver.

Leaf-cutting ant attack in initial pine plantations and growth of defoliated plants

The objective of this work was to evaluate the natural attack by Acromyrmex crassispinus in initial Pinus taeda plantations without control measures against ants, as well as the effect of defoliation in seedlings of P. taeda. Evaluations of the attack of leaf-cutting ants on P. taeda plantations were done monthly in the first six months, then 9 and 12 months after planting. The percentages of plants that were naturally attacked by ants were registered. The effect of defoliation was evaluated by artificial defoliation, simulating the natural patterns of attack by A. crassispinus on P. taeda seedlings. The natural attack of A. crassispinus was greater during the first months after planting, being more intense in the first 30 days. Artificial defoliation indicated that there were no significant losses in diameter and height in plants with less than 75% defoliation. However, there were significant losses in diameter and height in plants with 100% defoliation, independently of the cut of the apical meristem, and also plant death. The control of leaf-cutting ants in P. taeda plantings, in which A. crassispinus is the most frequent leaf-cutting ant, should be intense only at the beginning of planting, since the most severe attacks occur during this time.

Safety of a new algorithm for the management of childhood illness (Almanach) to improve quality of care and rational use of drugs

Introduction New evidence from randomized controlled and etiology of fever studies, the availability of reliable RDT for malaria, and novel technologies call for revision of the IMCI strategy. We developed a new algorithm based on (i) a systematic review of published studies assessing the safety and appropriateness of RDT and antibiotic prescription, (ii) results from a clinical and microbiological investigation of febrile children aged <5 years, (iii) international expert IMCI opinions. The aim of this study was to assess the safety of the new algorithm among patients in urban and rural areas of Tanzania.Materials and Methods The design was a controlled noninferiority study. Enrolled children aged 2-59 months with any illness were managed either by a study clinician using the new Almanach algorithm (two intervention health facilities), or clinicians using standard practice, including RDT (two control HF). At day 7 and day 14, all patients were reassessed. Patients who were ill in between or not cured at day 14 were followed until recovery or death. Primary outcome was rate of complications, secondary outcome rate of antibiotic prescriptions.Results 1062 children were recruited. Main diagnoses were URTI 26%, pneumonia 19% and gastroenteritis (9.4%). 98% (531/541) were cured at D14 in the Almanach arm and 99.6% (519/521) in controls. Rate of secondary hospitalization was 0.2% in each. One death occurred in controls. None of the complications was due to withdrawal of antibiotics or antimalarials at day 0. Rate of antibiotic use was 19% in the Almanach arm and 84% in controls.Conclusion Evidence suggests that the new algorithm, primarily aimed at the rational use of drugs, is as safe as standard practice and leads to a drastic reduction of antibiotic use. The Almanach is currently being tested for clinician adherence to proposed procedures when used on paper or a mobile phone

Tumor sensitizing function and mechanism of action of a RasGAP derived peptide

Cancer is the second cause of death after cardio-vascular diseases in economically developed countries. Two of the most commonly used anti-cancer therapies are chemo and radiotherapy. Despite the remarkable advances made in term of delivery and specificity of these two anti-tumor regimens, their toxicity towards healthy tissue remains a limitation. A promising approach to overcome this obstacle would be the utilization of therapeutic peptides that specifically augment the sensitivity of tumoral cells to treatments. Lower therapeutical doses would then be required to kill malignant cells, limiting toxic effects on healthy tissues. It was previously shown in our laboratory that the caspase-3 generated fragment N2 of RasGAP is able to potentiate the genotoxin-induced apoptosis selectively in cancer cells. In this work we show that fragment N2 strictly requires a cytoplasmic localization to deliver its pro-apoptotic effect in genotoxin-treated cancer cells. The tumor sensitizing capacity of fragment N2 was found to reside within the 10 amino acid sequence 317-326. Our laboratory earlier demonstrated that a peptide corresponding to amino acids 317 to 326 of RasGAP fused to the TAT cell permeable moiety, called TAT-RasGAP317.326, is able to sensitize cancer cells, but not normal cells, to genotoxin-induced apoptosis. In the present study we describe the capacity of TAT-RasGAP 317.326 to sensitize tumors to both chemo and radiotherapy in an in vivo mouse model. The molecular mechanism underlying the TAT-RasGAP 317.326-mediated sensitization starts now to be elucidated. We demonstrate that G3BP1, an endoribonuclease binding to amino acids 317-326 of RasGAP, is not involved in the sensitization mechanism. We also provide evidence showing that TAT-RasGAP3 17-326 potentiates the genotoxin-mediated activation of Bax in a tBid-dependent manner. Altogether our results show that TAT-RasGAP 317.326 could be potentially used in cancer therapy as sensitizer, in order to improve the efficacy of chemo and radiotherapy and prolong the life expectancy of cancer patients. Moreover, the understanding of the TAT-RasGAP317.326 mode of action might help to unravel the mechanisms by which cancer cells resist to chemo and radiotherapy and therefore to design more targeted and efficient anti-tumoral strategies.

Putkilämmönsiirtimien mitoitustyökalujen kehittäminen

Diplomityön tarkoituksena on kehittää tietokoneohjelma putkilämmönsiirtimen vaippapuolen painehäviön laskemiseksi. Ohjelmalla voidaan varmistaa lämmönsiirtimen mitoitusvaiheessa, että vaippapuolen painehäviö ei ylitä sallittuja rajoja. Ohjelmatäydentää olemassa olevia mitoitusohjelmia. Tässä diplomityössä käsitellään ainoastaan höyryvoimalaitosprosesseissa käytettäviä putkilämmönsiirtimiä. Työn kirjallisessa osassa on selvitetty periaate höyryvoimalaitosprosessista ja siinä käytettävistä putkilämmönsiirtimistä sekä esitetty putkilämmönsiirtimien rakenne, yleinen suunnittelu ja lämpö- ja virtaustekninen mitoitus. Painehäviön laskennassa käytetyt ja lämpö- ja virtausteknistä mitoitusta käsittelevässä kappaleessa esitetyt yhtälöt perustuvat Bell-Delawaren menetelmään. Painehäviönlaskentaohjelma on toteutettu hyväksikäyttäen Microsoft Excel taulukkolaskentaa ja Visual Basic -ohjelmointikieltä. Painehäviön laskenta perustuu segmenttivälilevyillä varustetun putkilämmönsiirtimen vaippapuolen yksifaasivirtaukseen. Lämmönsiirtimen lauhdutinosan painehäviö oletetaan merkityksettömäksi, joten kokonaispainehäviö muodostuu höyryn- ja lauhteenjäähdyttimessä. Kehitetty ohjelma on suunniteltu erityisesti lauhteenjäähdyttimessä muodostuvan painehäviön laskentaan. Ohjelmalla laskettuja painehäviön arvoja on verrattu todellisesta lämmönsiirtimestä mitattuihin arvoihin. Lasketut arvotvastaavat hyvin mittaamalla saatuja, eikä tuloksissa ilmene mitään systemaattista virhettä. Ohjelma on valmis käytettäväksi putkilämmönsiirtimien mitoitustyökaluna. Diplomityön pohjalta on tehty ehdotukset ohjelman edelleen kehittämiseksi.

Systematic review of evidence and consensus on diverticulitis: an analysis of national and international guidelines.

AIM: The study aimed to analyse the currently available national and international guidelines for areas of consensus and contrasting recommendations in the treatment of diverticulitis and thereby to design questions for future research. METHOD: MEDLINE, EMBASE and PubMed were systematically searched for guidelines on diverticular disease and diverticulitis. Inclusion was confined to papers in English and those < 10 years old. The included topics were classified as consensus or controversy between guidelines, and the highest level of evidence was scored as sufficient (Oxford Centre of Evidence-Based Medicine Level of Evidence of 3a or higher) or insufficient. RESULTS: Six guidelines were included and all topics with recommendations were compared. Overall, in 13 topics consensus was reached and 10 topics were regarded as controversial. In five topics, consensus was reached without sufficient evidence and in three topics there was no evidence and no consensus. Clinical staging, the need for intraluminal imaging, dietary restriction, duration of antibiotic treatment, the protocol for abscess treatment, the need for elective surgery in subgroups of patients, the need for surgery after abscess treatment and the level of the proximal resection margin all lack consensus or evidence. CONCLUSION: Evidence on the diagnosis and treatment of diverticular disease and diverticulitis ranged from nonexistent to strong, regardless of consensus. The most relevant research questions were identified and proposed as topics for future research.

Computational Analysis and Optimization of Real Gas Flow In Small Centrifugal Compressors

Small centrifugal compressors are more and more widely used in many industrialsystems because of their higher efficiency and better off-design performance comparing to piston and scroll compressors as while as higher work coefficient perstage than in axial compressors. Higher efficiency is always the aim of the designer of compressors. In the present work, the influence of four partsof a small centrifugal compressor that compresses heavy molecular weight real gas has been investigated in order to achieve higher efficiency. Two parts concern the impeller: tip clearance and the circumferential position of the splitter blade. The other two parts concern the diffuser: the pinch shape and vane shape. Computational fluid dynamics is applied in this study. The Reynolds averaged Navier-Stokes flow solver Finflo is used. The quasi-steady approach is utilized. Chien's k-e turbulence model is used to model the turbulence. A new practical real gas model is presented in this study. The real gas model is easily generated, accuracy controllable and fairly fast. The numerical results and measurements show good agreement. The influence of tip clearance on the performance of a small compressor is obvious. The pressure ratio and efficiency are decreased as the size of tip clearance is increased, while the total enthalpy rise keeps almost constant. The decrement of the pressure ratio and efficiency is larger at higher mass flow rates and smaller at lower mass flow rates. The flow angles at the inlet and outlet of the impeller are increased as the size of tip clearance is increased. The results of the detailed flow field show that leakingflow is the main reason for the performance drop. The secondary flow region becomes larger as the size of tip clearance is increased and the area of the main flow is compressed. The flow uniformity is then decreased. A detailed study shows that the leaking flow rate is higher near the exit of the impeller than that near the inlet of the impeller. Based on this phenomenon, a new partiallyshrouded impeller is used. The impeller is shrouded near the exit of the impeller. The results show that the flow field near the exit of the impeller is greatly changed by the partially shrouded impeller, and better performance is achievedthan with the unshrouded impeller. The loading distribution on the impeller blade and the flow fields in the impeller is changed by moving the splitter of the impeller in circumferential direction. Moving the splitter slightly to the suction side of the long blade can improve the performance of the compressor. The total enthalpy rise is reduced if only the leading edge of the splitter ismoved to the suction side of the long blade. The performance of the compressor is decreased if the blade is bended from the radius direction at the leading edge of the splitter. The total pressure rise and the enthalpy rise of thecompressor are increased if pinch is used at the diffuser inlet. Among the fivedifferent pinch shape configurations, at design and lower mass flow rates the efficiency of a straight line pinch is the highest, while at higher mass flow rate, the efficiency of a concave pinch is the highest. The sharp corner of the pinch is the main reason for the decrease of efficiency and should be avoided. The variation of the flow angles entering the diffuser in spanwise direction is decreased if pinch is applied. A three-dimensional low solidity twisted vaned diffuser is designed to match the flow angles entering the diffuser. The numerical results show that the pressure recovery in the twisted diffuser is higher than in a conventional low solidity vaned diffuser, which also leads to higher efficiency of the twisted diffuser. Investigation of the detailed flow fields shows that the separation at lower mass flow rate in the twisted diffuser is later than in the conventional low solidity vaned diffuser, which leads to a possible wider flow range of the twisted diffuser.

Solution scanning as a key policy tool: identifying management interventions to help maintain and enhance regulating ecosystem services

The major task of policy makers and practitioners when confronted with a resource management problem is to decide on the potential solution(s) to adopt from a range of available options. However, this process is unlikely to be successful and cost effective without access to an independently verified and comprehensive available list of options. There is currently burgeoning interest in ecosystem services and quantitative assessments of their importance and value. Recognition of the value of ecosystem services to human well-being represents an increasingly important argument for protecting and restoring the natural environment, alongside the moral and ethical justifications for conservation. As well as understanding the benefits of ecosystem services, it is also important to synthesize the practical interventions that are capable of maintaining and/or enhancing these services. Apart from pest regulation, pollination, and global climate regulation, this type of exercise has attracted relatively little attention. Through a systematic consultation exercise, we identify a candidate list of 296 possible interventions across the main regulating services of air quality regulation, climate regulation, water flow regulation, erosion regulation, water purification and waste treatment, disease regulation, pest regulation, pollination and natural hazard regulation. The range of interventions differs greatly between habitats and services depending upon the ease of manipulation and the level of research intensity. Some interventions have the potential to deliver benefits across a range of regulating services, especially those that reduce soil loss and maintain forest cover. Synthesis and applications: Solution scanning is important for questioning existing knowledge and identifying the range of options available to researchers and practitioners, as well as serving as the necessary basis for assessing cost effectiveness and guiding implementation strategies. We recommend that it become a routine part of decision making in all environmental policy areas.

Effect of humic substances and weather conditions on leaf biochemical changes of fertigated guava tree, during orchard establishment

In São Francisco Valley, Northeast Brazil, humic substances have been used by growers in fertigated fruit crops, due to its improvements on soil conditions and in plant nutrient uptake, metabolism and growth, reported from different growing places and crops. Nevertheless, little information about plant response to humic substance usage for local soil, weather and cropping system conditions is known. Hence, the metabolic response of guava tree during the orchard establishment to fertigation with humic substances and its correlation to the weather conditions were evaluated in Petrolina, State of Pernambuco. The treatments were manure application in soil combined with mineral fertilizers and humic substances applied through water of irrigation. The results showed that the fertigation treatments and plant age did not present conclusive effects in guava leaf contents of carbohydrates, proteins and amino acids. On the other side, the leaf contents of these compounds were influenced by the weather conditions.

Discriminating crop, weeds and soil surface with a terrestrial LIDAR sensor

In this study, the evaluation of the accuracy and performance of a light detection and ranging (LIDAR) sensor for vegetation using distance and reflection measurements aiming to detect and discriminate maize plants and weeds from soil surface was done. The study continues a previous work carried out in a maize field in Spain with a LIDAR sensor using exclusively one index, the height profile. The current system uses a combination of the two mentioned indexes. The experiment was carried out in a maize field at growth stage 12–14, at 16 different locations selected to represent the widest possible density of three weeds: Echinochloa crus-galli (L.) P.Beauv., Lamium purpureum L., Galium aparine L.and Veronica persica Poir.. A terrestrial LIDAR sensor was mounted on a tripod pointing to the inter-row area, with its horizontal axis and the field of view pointing vertically downwards to the ground, scanning a vertical plane with the potential presence of vegetation. Immediately after the LIDAR data acquisition (distances and reflection measurements), actual heights of plants were estimated using an appropriate methodology. For that purpose, digital images were taken of each sampled area. Data showed a high correlation between LIDAR measured height and actual plant heights (R2 = 0.75). Binary logistic regression between weed presence/absence and the sensor readings (LIDAR height and reflection values) was used to validate the accuracy of the sensor. This permitted the discrimination of vegetation from the ground with an accuracy of up to 95%. In addition, a Canonical Discrimination Analysis (CDA) was able to discriminate mostly between soil and vegetation and, to a far lesser extent, between crop and weeds. The studied methodology arises as a good system for weed detection, which in combination with other principles, such as vision-based technologies, could improve the efficiency and accuracy of herbicide spraying.

Fruit quality of 'Tahiti' lime (Citrus latifolia Tanak) grafted on twelve different rootstocks

In the present work, the effect of twelve rootstocks on fruit quality of the nucellar clone IAC-5 of 'Tahiti' lime, (Citrus latifolia Tanaka) and the influence of fruit position on tree in fruit quality was evaluated in the Citrus Experimental Station of Bebedouro (EECB), located in the Bebedouro county, state of São Paulo, Brazil. A 8.0 x 5.0m planting frame was utilized. The evaluated rootstocks were: 'Carrizo' citrange (C. sinensis (L.) Osbeck x Poncirus trifoliata (L.) Raf.); the hybrids 'Rangpur' lime x 'Swingle' citrumello (C. limonia Osbeck x P. trifoliata Raf) and 'Changsha' x 'English Small'(C. sunki Hort. ex Tan. x P. trifoliata Raf.); the mandarins 'Sun Chu Sha Kat' (C. reticulata Blanco) and 'Sunki' (C. sunki Hort. ex Tanaka); the 'Rangpur' limes 'Cravo Limeira' and ' Cravo FCAV' (C. limonia Osbeck); the 'Swingle' citrumello (P. trifoliata Raf. x C. paradisi Macf.); the 'Orlando' tangelo (C. reticulata Blanco x C. paradisi Macf.) and the trifoliates cvs. 'Rubidoux', 'FCAV' and 'Flying Dragon' (P. trifoliata Raf.). The experiment was arranged in a randomized block design, with twelve treatments, six replicates and one plant per plot. The rootstocks induced differences in fruit quality; however, all the evaluated quality characteristics were within the values considered as normal and acceptable for the variety, constituting good alternative rootstocks for the 'Rangpur' lime. Additionally, the fruit position in the plant (northeastern or southwestern) had a significant influence on the external fruit color regardless of the rootstock.

Diet-related buccal dental microwear patterns in central african pygmy foragers and bantu-speaking farmer and pastoralist populations.

Pygmy hunter-gatherers from Central Africa have shared a network of socioeconomic interactions with non-Pygmy Bantu speakers since agropastoral lifestyle spread across sub-Saharan Africa. Ethnographic studies have reported that their diets differ in consumption of both animal proteins and starch grains. Hunted meat and gathered plant foods, especially underground storage organs (USOs), are dietary staples for pygmies. However, scarce information exists about forager-farmer interaction and the agricultural products used by pygmies. Since the effects of dietary preferences on teeth in modern and past pygmies remain unknown, we explored dietary history through quantitative analysis of buccal microwear on cheek teeth in well-documented Baka pygmies. We then determined if microwear patterns differ among other Pygmy groups (Aka, Mbuti, and Babongo) and between Bantu-speaking farmer and pastoralist populations from past centuries. The buccal dental microwear patterns of Pygmy hunter-gatherers and non-Pygmy Bantu pastoralists show lower scratch densities, indicative of diets more intensively based on nonabrasive foodstuffs, compared with Bantu farmers, who consume larger amounts of grit from stoneground foods. The Baka pygmies showed microwear patterns similar to those of ancient Aka and Mbuti, suggesting that the mechanical properties of their preferred diets have not significantly changed through time. In contrast, Babongo pygmies showed scratch densities and lengths similar to those of the farmers, consistent with sociocultural contacts and genetic factors. Our findings support that buccal microwear patterns predict dietary habits independent of ecological conditions and reflect the abrasive properties of preferred or fallback foods such as USOs, which may have contributed to the dietary specializations of ancient human populations.

Trade-off between constitutive and inducible resistance against herbivores is only partially explained by gene expression and glucosinolate production.

The hypothesis that constitutive and inducible plant resistance against herbivores should trade-off because they use the same resources and impose costs to plant fitness has been postulated for a long time. Negative correlations between modes of deployment of resistance and defences have been observed across and within species in common garden experiments. It was therefore tested whether that pattern of resistance across genotypes follows a similar variation in patterns of gene expression and chemical defence production. Using the genetically tractable model Arabidopsis thaliana and different modes of induction, including the generalist herbivore Spodoptera littoralis, the specialist herbivore Pieris brassicae, and jasmonate application, constitutive and inducibility of resistance was measured across seven A. thaliana accessions that were previously selected based on constitutive levels of defence gene expression. According to theory, it was found that modes of resistance traded-off among accessions, particularly against S. littoralis, in which accessions investing in high constitutive resistance did not increase it substantially after attack and vice-versa. Accordingly, the average expression of eight genes involved in glucosinolate production negatively predicted larval growth across the seven accessions. Glucosinolate production and genes related to defence induction on healthy and herbivore-damaged plants were measured next. Surprisingly, only a partial correlation between glucosinolate production, gene expression, and the herbivore resistance results was found. These results suggest that the defence outcome of plants against herbivores goes beyond individual molecules or genes but stands on a complex network of interactions.

Robots and robotic systems for the electronics and telecommunication industry

Tämä diplomityö tutkii elektroniikka- ja telekommunikaatioteollisuutta sekä siihen läheisesti liittyviä robotteja ja robottijärjestelmiä. Tavoitteena on määrittää E&T-teollisuuden prosesseihin soveltuvien robottien testausmenetelmä. Tavoitteena on myös selvittää kahden ABB:n robotin soveltuvuutta E&T-teollisuuden tarpeisiin. Muutamia systemaattisia valmistusjärjestelmien suunnitteluun soveltuvia menetelmiä ja apuvälineitä on myös käsitelty. Alussa työ keskittyy elektroniikka- ja telekommunikaatioteollisuuden nykytilan tutkimiseen sekä siellä vallitsevien ja ennustettujen trendien kartoitukseen. Kohdat “Collaborative manufacturing” ja E&T-teollisuuden valmistusjärjestelmille asettamat vaatimukset käydään yksityiskohtaisesti läpi. Tutkimuksen pääkohteina ovat robotit, erityisesti ABB:n IRB 140 ja IRB 340 sekä robottien testausmenetelmän määrittäminen. Työssä käydään läpi IRB 340:llä suoritetut testit, jotka tehtiin sekä konenäköjärjestelmää apuna käyttäen että ilman. Myös TTKK:lla suoritetut robottitestit on käyty läpi. Robottien testituloksia on analysoitu ja vertailtu muihin robotteihin. Testausmenetelmät perustuvat ISO 9283 standardiin. Viimeinen osa työstä esittelee robottijärjestelmien systemaattiseen suunnitteluun soveltuvia menetelmiä ja apuvälineitä. Esillä ovat mm. Modular function deployment (MFD) ja The system design method (SDM).

Design of User Authentication System for Multi-operator wireless LANs

Langattomat lähiverkot ovat viime vuosikymmeninä saavuttaneet suuren suosion. Tässä työssä käsitellään käyttäjien todentamisjärjestelmän suunnittelua ja kehitystä langattomaan monioperaattoriverkkoon. Langattomassa monioperaattoriverkossa käyttäjillä on mahdollisuus käyttää eri operaattoreiden palveluita. Aluksi käsitellään olemassa olevia todentamismenetelmiä ja -järjestelmiä. minkä jälkeen kuvaillaan todentamisjärjestelmä langattomille monioperaattoriverkoille. Todentamisjärjestelmän ratkaisuvaihtoehtoja esitellään kaksi, niin sanotut moni- istunto - ja yksittäisistuntomalli. Moni-istuntomalli on normaali lähestymistapa käyttäjien todentamiseen tietokonejärjestelmissä. Siinä käyttäjän pitää tunnistautua ja todentaa itsensä jokaiselle verkon palvelulle erikseen. Yksittäisistuntomallissa pyritään parempaan luotettavuuteen ja käytettävyyteen. Siinä käyttäjä todentaa itsensä vain kerran ja voi sen jälkeen päästä useisiin palveluihin. Työn loppuosassa kuvaillaan suunnitellun järjestelmän toteutusta. Lisäksi ehdotetaan vaihtoehtoisia toteutustapoja, analysoidaan järjestelmän heikkouksia ja kerrotaan jatkokehitysmahdoillisuuksista.