Estimation of cutting volume with three inventory methods for harvest planning in Canadian boreal forests.

Two methods of pre-harvest inventory were designed and tested on three cutting sites containing a total of 197 500 m3 of wood. These sites were located on flat-ground boreal forests located in northwestern Quebec. Both methods studied involved scaling of trees harvested to clear the road path one year (or more) prior to harvest of adjacent cut-blocks. The first method (ROAD) considers the total road right-of-way volume divided by the total road area cleared. The resulting volume per hectare is then multiplied by the total cut-block area scheduled for harvest during the following year to obtain the total estimated cutting volume. The second method (STRATIFIED) also involves scaling of trees cleared from the road. However, in STRATIFIED, log scaling data are stratified by forest stand location. A volume per hectare is calculated for each stretch of road that crosses a single forest stand. This volume per hectare is then multiplied by the remaining area of the same forest stand scheduled for harvest one year later. The sum of all resulting estimated volumes per stand gives the total estimated cutting-volume for all cut-blocks adjacent to the studied road. A third method (MNR) was also used to estimate cut-volumes of the sites studied. This method represents the actual existing technique for estimating cutting volume in the province of Quebec. It involves summing the cut volume for all forest stands. The cut volume is estimated by multiplying the area of each stand by its estimated volume per hectare obtained from standard stock tables provided by the governement. The resulting total estimated volume per cut-block for all three methods was then compared with the actual measured cut-block volume (MEASURED). This analysis revealed a significant difference between MEASURED and MNR methods with the MNR volume estimate being 30 % higher than MEASURED. However, no significant difference from MEASURED was observed for volume estimates for the ROAD and STRATIFIED methods which respectively had estimated cutting volumes 19 % and 5 % lower than MEASURED. Thus the ROAD and STRATIFIED methods are good ways to estimate cut-block volumes after road right-of-way harvest for conditions similar to those examined in this study.

DNA polymorphism and local variation in base-pair orientation: a theoretical rationale

Basepair stacking calculations have been carried out to understand the conformational polymorphism of DNA and its sequence dependence. The recently developed self-consistent parameter set, which is specially suitable for describing irregular DNA structures, has been used to describe the geometry of a basepair doublet. While for basepairs without any propeller, the favourable stacking patterns do not appear to have very strong features, much more noticeable sequence dependent stacking patterns emerge once a propeller is applied to the basepairs. The absolute minima for most sequences occurs for a doublet geometry close to the B-DNA fibre models. Hence in the B-DNA region, no strong sequence dependent features are found, but the range of doublet geometries observed in the crystal structures generally lie within the low energy contours, obtained from stacking energy calculations. The doublet geometry corresponding to the A-DNA fibre model is not energetically favourable for the purine-pyrimidine sequences, which prefer small roll angle values when the slide has a large negative value as in A-DNA. However positive roll with large negative slide is allowed for GG, GA, AG and the pyrimidine-purine steps. This is consistent with the observed geometries of various steps in A-DNA crystals. Thus the general features of the basepair doublets predicted from these theoretical studies agree very well with the results from crystal structure analysis. However, since most sequences show an overall preference for B-type doublet geometry, the B --> A transition for random sequence DNA cannot be explained on the basis of basepair stacking interactions.

Local systems, global impacts : Using life cycle assessment to analyse the potential and constraints of industrial symbioses

Human activities extract and displace different substances and materials from the earth s crust, thus causing various environmental problems, such as climate change, acidification and eutrophication. As problems have become more complicated, more holistic measures that consider the origins and sources of pollutants have been called for. Industrial ecology is a field of science that forms a comprehensive framework for studying the interactions between the modern technological society and the environment. Industrial ecology considers humans and their technologies to be part of the natural environment, not separate from it. Industrial operations form natural systems that must also function as such within the constraints set by the biosphere. Industrial symbiosis (IS) is a central concept of industrial ecology. Industrial symbiosis studies look at the physical flows of materials and energy in local industrial systems. In an ideal IS, waste material and energy are exchanged by the actors of the system, thereby reducing the consumption of virgin material and energy inputs and the generation of waste and emissions. Companies are seen as part of the chains of suppliers and consumers that resemble those of natural ecosystems. The aim of this study was to analyse the environmental performance of an industrial symbiosis based on pulp and paper production, taking into account life cycle impacts as well. Life Cycle Assessment (LCA) is a tool for quantitatively and systematically evaluating the environmental aspects of a product, technology or service throughout its whole life cycle. Moreover, the Natural Step Sustainability Principles formed a conceptual framework for assessing the environmental performance of the case study symbiosis (Paper I). The environmental performance of the case study symbiosis was compared to four counterfactual reference scenarios in which the actors of the symbiosis operated on their own. The research methods used were process-based life cycle assessment (LCA) (Papers II and III) and hybrid LCA, which combines both process and input-output LCA (Paper IV). The results showed that the environmental impacts caused by the extraction and processing of the materials and the energy used by the symbiosis were considerable. If only the direct emissions and resource use of the symbiosis had been considered, less than half of the total environmental impacts of the system would have been taken into account. When the results were compared with the counterfactual reference scenarios, the net environmental impacts of the symbiosis were smaller than those of the reference scenarios. The reduction in environmental impacts was mainly due to changes in the way energy was produced. However, the results are sensitive to the way the reference scenarios are defined. LCA is a useful tool for assessing the overall environmental performance of industrial symbioses. It is recommended that in addition to the direct effects, the upstream impacts should be taken into account as well when assessing the environmental performance of industrial symbioses. Industrial symbiosis should be seen as part of the process of improving the environmental performance of a system. In some cases, it may be more efficient, from an environmental point of view, to focus on supply chain management instead.  

Methods and applications for improving parameter prediction models for stand structures in Finland

This thesis report attempts to improve the models for predicting forest stand structure for practical use, e.g. forest management planning (FMP) purposes in Finland. Comparisons were made between Weibull and Johnson s SB distribution and alternative regression estimation methods. Data used for preliminary studies was local but the final models were based on representative data. Models were validated mainly in terms of bias and RMSE in the main stand characteristics (e.g. volume) using independent data. The bivariate SBB distribution model was used to mimic realistic variations in tree dimensions by including within-diameter-class height variation. Using the traditional method, diameter distribution with the expected height resulted in reduced height variation, whereas the alternative bivariate method utilized the error-term of the height model. The lack of models for FMP was covered to some extent by the models for peatland and juvenile stands. The validation of these models showed that the more sophisticated regression estimation methods provided slightly improved accuracy. A flexible prediction and application for stand structure consisted of seemingly unrelated regression models for eight stand characteristics, the parameters of three optional distributions and Näslund s height curve. The cross-model covariance structure was used for linear prediction application, in which the expected values of the models were calibrated with the known stand characteristics. This provided a framework to validate the optional distributions and the optional set of stand characteristics. Height distribution is recommended for the earliest state of stands because of its continuous feature. From the mean height of about 4 m, Weibull dbh-frequency distribution is recommended in young stands if the input variables consist of arithmetic stand characteristics. In advanced stands, basal area-dbh distribution models are recommended. Näslund s height curve proved useful. Some efficient transformations of stand characteristics are introduced, e.g. the shape index, which combined the basal area, the stem number and the median diameter. Shape index enabled SB model for peatland stands to detect large variation in stand densities. This model also demonstrated reasonable behaviour for stands in mineral soils.

Room temperature creep in amorphous alloys: Influence of initial strain and free volume

The role of imposed strain on the room temperature time-dependent deformation behavior of bulk metallic glasses (BMGs) was systematically investigated through spherical nanoindentation creep experiments. The results show that creep occurred even at very low strains within elastic regimes and, interestingly, a precipitous increase in creep rate was found in plastic regimes, with BMG that had a higher free volume exhibiting greater creep rates. The results are discussed in terms of prevailing mechanisms of elastic/plastic deformation of amorphous alloys. (c) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Production process of Scots pine.

The accompanying collective research report is the result of the research project in 1986­90 between The Finnish Academy and the former Soviet Academy of Sciences. The project was organized around common field work in Finland and in the former Soviet Union and theoretical analyses of tree growth determining processes. Based on theoretical analyses, dynamic stand growth models were made and their parameters were determined utilizing the field results. Annual cycle affects the tree growth. Our theoretical approach was based on adaptation to local climate conditions from Lapland to South Russia. The initiation of growth was described as a simple low and high temperature accumulation driven model. Linking the theoretical model with long term temperature data allowed us to analyze what type of temperature response produced favorable outcome in different climates. Initiation of growth consumes the carbohydrate reserves in plants. We measured the dynamics of insoluble and soluble sugars in the very northern and Karelian conditions. Clear cyclical pattern was observed but the differences between locations were surprisingly small. Analysis of field measurements of CO2 exchange showed that irradiance is the dominating factor causing variation in photosynthetic rate in natural conditions during summer. The effect of other factors is so small that they can be omitted without any considerable loss of accuracy. A special experiment carried out in Hyytiälä showed that the needle living space, defined as the ratio between the shoot cylindric volume and needle surface area, correlates with the shoot photosynthesis. The penetration of irradiance into Scots pine canopy is a complicated phenomenon because of the movement of the sun on the sky and the complicated structure of branches and needles. A moderately simple but balanced forest radiation regime submodel was constructed. It consists of the tree crown and forest structure, the gap probability calculation and the consideration of spatial and temporal variation of radiation inside the forest. The common field excursions in different geographical regions resulted in a lot of experimental data of regularities of woody structures. The water transport seems to be a good common factor to analyse these properties of tree structure. There are evident regressions between cross-sectional areas measured at different locations along the water pathway from fine roots to needles. The observed regressions have clear geographical trends. For example, the same cross-sectional area can support three times higher needle mass in South Russia than in Lapland. Geographical trends can also be seen in shoot and needle structure. Analysis of data published by several Russian authors show, that one ton of needles transpire 42 ton of water a year. This annual amount of transpiration seems to be independent of geographical location, year and site conditions. The produced theoretical and experimental material is utilised in the development of stand growth model that describes the growth and development of Scots pine stands in Finland and the former Soviet Union. The core of the model is carbon and nutrient balances. This means that carbon obtained in photosynthesis is consumed for growth and maintenance and nutrients are taken according to the metabolic needs. The annual photosynthetic production by trees in the stand is determined as a function of irradiance and shading during the active period. The utilisation of the annual photosynthetic production to the growth of different components of trees is based on structural regularities. Since the fundamental metabolic processes are the same in all locations the same growth model structure can be applied in the large range of Scots pine. The annual photosynthetic production and structural regularities determining the allocation of resources have geographical features. The common field measurements enable the application of the model to the analysis of growth and development of stands growing on the five locations of experiments. The model enables the analysis of geographical differences in the growth of Scots pine. For example, the annual photosynthetic production of a 100-year-old stand at Voronez is 3.5 times higher than in Lapland. The share consumed to needle growth (30 %) and to growth of branches (5 %) seems to be the same in all locations. In contrast, the share of fine roots is decreasing when moving from north to south. It is 20 % in Lapland, 15 % in Hyytiälä Central Finland and Kentjärvi Karelia and 15 % in Voronez South Russia. The stem masses (115­113 ton/ha) are rather similar in Hyytiälä, Kentjärvi and Voronez, but rather low (50 ton/ha) in Lapland. In Voronez the height of the trees reach 29 m being in Hyytiälä and Kentjärvi 22 m and in Lapland only 14 m. The present approach enables utilization of structural and functional knowledge, gained in places of intensive research, in the analysis of growth and development of any stand. This opens new possibilities for growth research and also for applications in forestry practice.

The Tourism-Development Nexus in Namibia : A Study on National Tourism Policy and Local Tourism Enterprises' Policy Knowledge

The tourism development nexus in southern Africa involves highly topical issues related to tourism planning, power relations, community participation, and natural resources. Namibia offers a particularly interesting context for the study of these issues due to its colonial legacy, vast tourism potential, recently adopted tourism policy and community-based approaches to tourism and natural resource management. This study is an interdisciplinary endeavour to analyse the role of tourism in Namibia s post-apartheid transformation process by focusing on Namibian tourism policy and local tourism enterprises' policy knowledge. Major attention is paid to how the tourism policy's national development objectives are understood and conceptualised by the representatives of different tourism enterprises and the ways in which they relate to the practical needs of the enterprises. Through such local policy knowledge the study explores various opportunities, challenges and constraints related to the promotion of tourism as a development strategy. The study utilises a political economy approach to tourism and development through three current and interrelated discourses which are relevant in the Namibian context. These are tourism, power and inequality, tourism and sustainable development, and tourism and poverty reduction. The qualitative research material was gathered in Namibia in 2006-2007 and 2008. This material consists of 34 semi-structured interviews in 16 tourism enterprises, including private trophy hunting farms and private lodges, small tour operators and community-based tourism enterprises. In addition, the research material consists of observations in the enterprises, and 37 informal and 23 expert interviews. The findings indicate that in the light of local tourism enterprises the tourism policy objectives appear more complex and ambiguous. Furthermore, they involve multiple meanings and interpretations which reflect the socio-economic stratification of the informants and Namibian society, together with the professional stratification of the tourism enterprises and restrictions on the capacity of tourism to address the development objectives. In the light of such findings it is obvious that aspects of power and inequality affect the tourism development nexus in Namibia. The study concludes that, as in the case of other southern African countries, in order to promote sustainable development and reduce poverty, Namibia should not only target tourism growth but pay attention to who benefits from that growth and how. From a political economy point of view, it is important that prevailing structural challenges are addressed equally in the planning of tourism, development and natural resource management. Such approach would help the Namibian majority to enjoy the benefits of increasing tourism in the country.

Whose ETSIP? National and local ownership of Namibia's education and training sector improvement programme

Tämä työ tarkastelee kansallista ja paikallista omistajuutta Namibian opetussektorin kehittämisohjelmassa. Opetussektorin kehittämisohjelma ETSIP on 15-vuotinen sektoriohjelma vuosille 2005-2015 ja sen tavoitteena on edesauttaa Namibian kehittymistä tietoyhteiskunnaksi. Tutkimuksen tarkoituksena on selvittää miten kansallinen ja paikallinen omistajuus on toteutunut ETSIP prosessin aikana. Erityisesti pyritään selvittämään paikallistason opetussektorin virkamiesten näkemyksiä ETSIP prosessista, heidän roolistaan siinä ja siitä millaisia vaikuttamisen ja hallinnan mahdollisuuksia heillä on ollut prosessin aikana. Tutkimuksen lähtökohta on laadullinen ja lähestymistapa konstruktionistinen: tutkimus tarkastelee todellisuutta ihmisten kokemusten, näkemysten ja toiminnan kautta. Tutkimusaineisto koostuu haastatteluista, epävirallisista keskusteluista, lehtiartikkeleista ja ETSIP dokumenteista. Tutkimus osoittaa että kansallinen omistajuus on epämääräinen käsite sillä kansallisia toimijoita ja näkemyksiä on useita. Tutkimus vahvistaa Castel-Brancon huomion siitä, että omistajuutta on tarkasteltava kontekstissaan: muuttuvana ja kilpailtuna. ETSIPin rinnalle ollaan valmistelemassa uutta strategista ohjelmaa opetusministeriölle mikä saattaa muuttaa omistajuutta ETSIPiin. ETSIP dokumenttien omistajuusretoriikka myötäilee kansainvälisiä sitoumuksia avun vaikuttavuuden parantamiseksi mutta niistä puuttuu syvällisempi analyysi siitä, miten kansallinen ja paikallinen omistajuus toteutuisi käytännössä. Avunantajien näkemys omistajuudesta on suppea: omistajuus nähdään lähinnä sitoutumisena ennalta määrättyyn politiikkaohjelmaan. Haastatteluaineistosta nousee esiin Whitfieldin ja Frazerin jaottelu suppeista ja laajoista omistajuuskäsityksistä. Sitoutumista ETSIP ohjelmaan pidetään tärkeänä mutta riittämättömänä määritteenä omistajuudelle. Paikallisella tasolla sitoutuminen ETSIP ohjelman periaatteisiin ja tavoitteisiin on toteutunut melko hyvin mutta jos omistajuutta tarkastellaan laajemmin vaikutusvallan ja hallinnan käsitteiden kautta voidaan todeta että omistajuus on ollut heikkoa. Paikallisella tasolla ei ole ollut juurikaan vaikutusvaltaa ETSIP ohjelman sisältöön eikä mahdollisuutta hallita ohjelman toteutusta ja päättää siitä mitä hankkeita ohjelman kautta rahoitetaan. Tujanin demokraattisen omistajuuden käsite kuvaa tarvetta muuttaa ja laajentaa omistajuusajattelua huomioiden paikallisen tason paremmin. Tämä tutkimus viittaa siihen että omistajuuden toteutuminen paikallisella tasolla edellyttäisi institutionaalisen kulttuurin muutosta ja institutionaalisen legitimiteetin vahvistamista. Omistajuuden mahdollistamiseksi paikallisella tasolla tarvittaisiin poliittista johtajuutta, luottamusta, vastuullisuuden kulttuurin kehittämistä, tehokkaampaa tiedonjakoa, laajaa osallistumista, vuoropuhelua ja yhteistyötä. Ennen kaikkea tarvittaisiin paikallisen tason vaikutusvaltaa päätöksenteossa ja kontrollia resurssien käytöstä. Tälle muutokselle on selvä tarve ja tilaus.

A local 2-approximation algorithm for the vertex cover problem

We present a distributed 2-approximation algorithm for the minimum vertex cover problem. The algorithm is deterministic, and it runs in (Δ + 1)2 synchronous communication rounds, where Δ is the maximum degree of the graph. For Δ = 3, we give a 2-approximation algorithm also for the weighted version of the problem.

A simple local 3-approximation algorithm for vertex cover

We present a local algorithm (constant-time distributed algorithm) for finding a 3-approximate vertex cover in bounded-degree graphs. The algorithm is deterministic, and no auxiliary information besides port numbering is required. (c) 2009 Elsevier B.V. All rights reserved.

A local 2-approximation algorithm for the vertex cover problem

We present a distributed 2-approximation algorithm for the minimum vertex cover problem. The algorithm is deterministic, and it runs in (Δ + 1)2 synchronous communication rounds, where Δ is the maximum degree of the graph. For Δ = 3, we give a 2-approximation algorithm also for the weighted version of the problem.

An optimal local approximation algorithm for max-min linear programs

In a max-min LP, the objective is to maximise ω subject to Ax ≤ 1, Cx ≥ ω1, and x ≥ 0 for nonnegative matrices A and C. We present a local algorithm (constant-time distributed algorithm) for approximating max-min LPs. The approximation ratio of our algorithm is the best possible for any local algorithm; there is a matching unconditional lower bound.

Analysing local algorithms in location-aware quasi-unit-disk graphs

A local algorithm with local horizon r is a distributed algorithm that runs in r synchronous communication rounds; here r is a constant that does not depend on the size of the network. As a consequence, the output of a node in a local algorithm only depends on the input within r hops from the node. We give tight bounds on the local horizon for a class of local algorithms for combinatorial problems on unit-disk graphs (UDGs). Most of our bounds are due to a refined analysis of existing approaches, while others are obtained by suggesting new algorithms. The algorithms we consider are based on network decompositions guided by a rectangular tiling of the plane. The algorithms are applied to matching, independent set, graph colouring, vertex cover, and dominating set. We also study local algorithms on quasi-UDGs, which are a popular generalisation of UDGs, aimed at more realistic modelling of communication between the network nodes. Analysing the local algorithms on quasi-UDGs allows one to assume that the nodes know their coordinates only approximately, up to an additive error. Despite the localisation error, the quality of the solution to problems on quasi-UDGs remains the same as for the case of UDGs with perfect location awareness. We analyse the increase in the local horizon that comes along with moving from UDGs to quasi-UDGs.

Local approximability of max-min and min-max linear programs

In a max-min LP, the objective is to maximise ω subject to Ax ≤ 1, Cx ≥ ω1, and x ≥ 0. In a min-max LP, the objective is to minimise ρ subject to Ax ≤ ρ1, Cx ≥ 1, and x ≥ 0. The matrices A and C are nonnegative and sparse: each row ai of A has at most ΔI positive elements, and each row ck of C has at most ΔK positive elements. We study the approximability of max-min LPs and min-max LPs in a distributed setting; in particular, we focus on local algorithms (constant-time distributed algorithms). We show that for any ΔI ≥ 2, ΔK ≥ 2, and ε > 0 there exists a local algorithm that achieves the approximation ratio ΔI (1 − 1/ΔK) + ε. We also show that this result is the best possible: no local algorithm can achieve the approximation ratio ΔI (1 − 1/ΔK) for any ΔI ≥ 2 and ΔK ≥ 2.