Optimal-stopping control for airborne collision avoidance and return-to-course flight

This paper considers an aircraft collision avoidance design problem that also incorporates design of the aircraft’s return-to-course flight. This control design problem is formulated as a non-linear optimal-stopping control problem; a formulation that does not require a prior knowledge of time taken to perform the avoidance and return-to-course manoeuvre. A dynamic programming solution to the avoidance and return-to-course problem is presented, before a Markov chain numerical approximation technique is described. Simulation results are presented that illustrate the proposed collision avoidance and return-to-course flight approach.

Modeling intrinsic noise and delays in chemical kinetics of coupled autoregulated oscillating cells

Delays are an important feature in temporal models of genetic regulation due to slow biochemical processes, such as transcription and translation. In this paper, we show how to model intrinsic noise effects in a delayed setting by either using a delay stochastic simulation algorithm (DSSA) or, for larger and more complex systems, a generalized Binomial τ-leap method (Bτ-DSSA). As a particular application, we apply these ideas to modeling somite segmentation in zebra fish across a number of cells in which two linked oscillatory genes (her1 and her7) are synchronized via Notch signaling between the cells.

Modelling the activation of words in human memory : the spreading activation, spooky-activation-at-a-distance and the entanglement models compared

Modelling how a word is activated in human memory is an important requirement for determining the probability of recall of a word in an extra-list cueing experiment. The spreading activation, spooky-action-at-a-distance and entanglement models have all been used to model the activation of a word. Recently a hypothesis was put forward that the mean activation levels of the respective models are as follows: Spreading � Entanglment � Spooking-action-at-a-distance This article investigates this hypothesis by means of a substantial empirical analysis of each model using the University of South Florida word association, rhyme and word norms.

Health Librarianship Workforce and Education : Research to plan the future. Final Report.

In late 2009, Health Libraries Australia (HLA) received a small grant to undertake a national research project to determine the future requirements for health librarians in the workforce in Australia and develop a structured, modular education framework (post-graduate qualification and continuing professional development structure) to meet these requirements. The main objective was to consider the education and professional development framework that would ensure that health librarians have a clearly defined scope of practice and the specific competency based knowledge and skills that enable them to contribute to the design and delivery of high quality health services in this country. The final report presents a detailed discussion of the changing Australian healthcare environment and the resulting impact on the health library sector, as well as an overview of international trends in health libraries and the implications for Australian health librarianship education. The research methodology is outlined, followed by an analysis of the findings from the two surveys with health librarians and health library managers and the semi-structured interviews conducted with employers. The Medical Library Association (MLA) in the United States had developed a policy document detailing the competencies required by health librarians. It was found that the MLA competencies represented an accepted professional framework of skills which could be used objectively in the survey instrument to measure the areas of professional knowledge and responsibilities that were relevant in the current workplace, and to identify how these requirements might change in the next three to five years. The research results underscore the imperative for health librarians to engage in regular, relevant professional development activities that will enable them to stay abreast with the rapid contextual changes impacting on their practice. In order to be accepted as key members of the multi-disciplinary health professional team, it is strongly believed that health librarians should commit to establishing the mechanisms for specialist certification maintained through compulsory CPD in an ongoing three-year cycle of revalidation. This development would align ALIA and health librarians with other health sector professional associations which are responsible for the self regulation of entry to and continuation in their profession.

HR practices and challenges in Chinese firms : comparison with Western firms

This research compares Chinese HRM with Western HRM, particularly in the areas of development of HR information systems (HRIS) and HR measurement systems and their relation to HR’s involvement as a strategic partner in firms. The research uses a 3-stage model of HRIS (workforce profiling, business insight, and strategic driver) based on studies of Irmer and Ellerby (2005) and Boudreau and Ramstad (2003) to compare the relative stages of development of Chinese and Western HRM. The quantitative aspect of the study comprises a survey of senior HR practitioners from 171 Chinese firms whose data is compared with data from Irmer and Ellerby’s study of Australian and U.S. HRM (2005) and Lawler et al’s series of studies of U.S firms (1995, 1998, 2001, 2004). The main results of the comparison are that Chinese HRM generally lags behind Western HRM. In particular, Chinese HR professionals allocate less time to strategic activities and their roles are less strategic than those of Western HR professionals. The HR measurement systems of Chinese firms are more limited in function, and the HR information systems of Chinese companies are less automated and integrated. However there is also evidence of a “two speed” HR system in China with a small proportion of firms having highly sophisticated HR systems but with a much larger proportion of Chinese firms than in the West having only the most basic HR information systems. This ‘two speed” system is in part attributable to a split between the relatively advanced HR systems of large State Owned Enterprises and the basic systems that predominate in smaller, growing Local Private firms. The survey study is complemented by a series of interviews with a number of senior Chinese HR practitioners who provide richer insights into their experiences and the challenges they face in contemporary Chinese firms.

Information literacy programs and research : an international review

This paper provides an overview of contemporary information literacy research and practice. While the content is highly selective, the intention has been to highlight international and Australian developments which have achieved significant recognition, which are representative of similar trends in other places, or which are unique in some way. There are three main foci in the paper. Firstly, an exploration of ways of interpreting the idea of information literacy. Secondly, a synthesis of various efforts to seek new directions in educational, community and workplace contexts, beginning with the major initiatives being undertaken in the United States. Thirdly, an introduction to some recent research, concluding with a summary of my own investigation into different ways of experiencing information literacy

Coupling hybrid-game strategies with particle swarm optimisation for multi-objective high lift systems design optimisation

This paper investigates the High Lift System (HLS) application of complex aerodynamic design problem using Particle Swarm Optimisation (PSO) coupled to Game strategies. Two types of optimization methods are used; the first method is a standard PSO based on Pareto dominance and the second method hybridises PSO with a well-known Nash Game strategies named Hybrid-PSO. These optimization techniques are coupled to a pre/post processor GiD providing unstructured meshes during the optimisation procedure and a transonic analysis software PUMI. The computational efficiency and quality design obtained by PSO and Hybrid-PSO are compared. The numerical results for the multi-objective HLS design optimisation clearly shows the benefits of hybridising a PSO with the Nash game and makes promising the above methodology for solving other more complex multi-physics optimisation problems in Aeronautics.

The geometric modelling of social frames and contexts

How do humans respond to their social context? This question is becoming increasingly urgent in a society where democracy requires that the citizens of a country help to decide upon its policy directions, and yet those citizens frequently have very little knowledge of the complex issues that these policies seek to address. Frequently, we find that humans make their decisions more with reference to their social setting, than to the arguments of scientists, academics, and policy makers. It is broadly anticipated that the agent based modelling (ABM) of human behaviour will make it possible to treat such social effects, but we take the position here that a more sophisticated treatment of context will be required in many such models. While notions such as historical context (where the past history of an agent might affect its later actions) and situational context (where the agent will choose a different action in a different situation) abound in ABM scenarios, we will discuss a case of a potentially changing context, where social effects can have a strong influence upon the perceptions of a group of subjects. In particular, we shall discuss a recently reported case where a biased worm in an election debate led to significant distortions in the reports given by participants as to who won the debate (Davis et al 2011). Thus, participants in a different social context drew different conclusions about the perceived winner of the same debate, with associated significant differences among the two groups as to who they would vote for in the coming election. We extend this example to the problem of modelling the likely electoral responses of agents in the context of the climate change debate, and discuss the notion of interference between related questions that might be asked of an agent in a social simulation that was intended to simulate their likely responses. A modelling technology which could account for such strong social contextual effects would benefit regulatory bodies which need to navigate between multiple interests and concerns, and we shall present one viable avenue for constructing such a technology. A geometric approach will be presented, where the internal state of an agent is represented in a vector space, and their social context is naturally modelled as a set of basis states that are chosen with reference to the problem space.

The flammability of metallic materials in normal and reduced gravity

Metallic materials exposed to oxygen-enriched atmospheres – as commonly used in the medical, aerospace, aviation and numerous chemical processing industries – represent a significant fire hazard which must be addressed during design, maintenance and operation. Hence, accurate knowledge of metallic materials flammability is required. Reduced gravity (i.e. space-based) operations present additional unique concerns, where the absence of gravity must also be taken into account. The flammability of metallic materials has historically been quantified using three standardised test methods developed by NASA, ASTM and ISO. These tests typically involve the forceful (promoted) ignition of a test sample (typically a 3.2 mm diameter cylindrical rod) in pressurised oxygen. A test sample is defined as flammable when it undergoes burning that is independent of the ignition process utilised. In the standardised tests, this is indicated by the propagation of burning further than a defined amount, or „burn criterion.. The burn criterion in use at the onset of this project was arbitrarily selected, and did not accurately reflect the length a sample must burn in order to be burning independent of the ignition event and, in some cases, required complete consumption of the test sample for a metallic material to be considered flammable. It has been demonstrated that a) a metallic material.s propensity to support burning is altered by any increase in test sample temperature greater than ~250-300 oC and b) promoted ignition causes an increase in temperature of the test sample in the region closest to the igniter, a region referred to as the Heat Affected Zone (HAZ). If a test sample continues to burn past the HAZ (where the HAZ is defined as the region of the test sample above the igniter that undergoes an increase in temperature of greater than or equal to 250 oC by the end of the ignition event), it is burning independent of the igniter, and should be considered flammable. The extent of the HAZ, therefore, can be used to justify the selection of the burn criterion. A two dimensional mathematical model was developed in order to predict the extent of the HAZ created in a standard test sample by a typical igniter. The model was validated against previous theoretical and experimental work performed in collaboration with NASA, and then used to predict the extent of the HAZ for different metallic materials in several configurations. The extent of HAZ predicted varied significantly, ranging from ~2-27 mm depending on the test sample thermal properties and test conditions (i.e. pressure). The magnitude of the HAZ was found to increase with increasing thermal diffusivity, and decreasing pressure (due to slower ignition times). Based upon the findings of this work, a new burn criterion requiring 30 mm of the test sample to be consumed (from the top of the ignition promoter) was recommended and validated. This new burn criterion was subsequently included in the latest revision of the ASTM G124 and NASA 6001B international test standards that are used to evaluate metallic material flammability in oxygen. These revisions also have the added benefit of enabling the conduct of reduced gravity metallic material flammability testing in strict accordance with the ASTM G124 standard, allowing measurement and comparison of the relative flammability (i.e. Lowest Burn Pressure (LBP), Highest No-Burn Pressure (HNBP) and average Regression Rate of the Melting Interface(RRMI)) of metallic materials in normal and reduced gravity, as well as determination of the applicability of normal gravity test results to reduced gravity use environments. This is important, as currently most space-based applications will typically use normal gravity information in order to qualify systems and/or components for reduced gravity use. This is shown here to be non-conservative for metallic materials which are more flammable in reduced gravity. The flammability of two metallic materials, Inconel® 718 and 316 stainless steel (both commonly used to manufacture components for oxygen service in both terrestrial and space-based systems) was evaluated in normal and reduced gravity using the new ASTM G124-10 test standard. This allowed direct comparison of the flammability of the two metallic materials in normal gravity and reduced gravity respectively. The results of this work clearly show, for the first time, that metallic materials are more flammable in reduced gravity than in normal gravity when testing is conducted as described in the ASTM G124-10 test standard. This was shown to be the case in terms of both higher regression rates (i.e. faster consumption of the test sample – fuel), and burning at lower pressures in reduced gravity. Specifically, it was found that the LBP for 3.2 mm diameter Inconel® 718 and 316 stainless steel test samples decreased by 50% from 3.45 MPa (500 psia) in normal gravity to 1.72 MPa (250 psia) in reduced gravity for the Inconel® 718, and 25% from 3.45 MPa (500 psia) in normal gravity to 2.76 MPa (400 psia) in reduced gravity for the 316 stainless steel. The average RRMI increased by factors of 2.2 (27.2 mm/s in 2.24 MPa (325 psia) oxygen in reduced gravity compared to 12.8 mm/s in 4.48 MPa (650 psia) oxygen in normal gravity) for the Inconel® 718 and 1.6 (15.0 mm/s in 2.76 MPa (400 psia) oxygen in reduced gravity compared to 9.5 mm/s in 5.17 MPa (750 psia) oxygen in normal gravity) for the 316 stainless steel. Reasons for the increased flammability of metallic materials in reduced gravity compared to normal gravity are discussed, based upon the observations made during reduced gravity testing and previous work. Finally, the implications (for fire safety and engineering applications) of these results are presented and discussed, in particular, examining methods for mitigating the risk of a fire in reduced gravity.

Augmenting mobile computing with video game elements to support, motivate and engage young people in educational, real-world events

Video games have shown great potential as tools that both engage and motivate players to achieve tasks and build communities in fantasy worlds. We propose that the application of game elements to real world activities can aid in delivering contextual information in interesting ways and help young people to engage in everyday events. Our research will explore how we can unite utility and fun to enhance information delivery, encourage participation, build communities and engage users with utilitarian events situated in the real world. This research aims to identify key game elements that work effectively to engage young digital natives, and provide guidelines to influence the design of interactions and interfaces for event applications in the future. This research will primarily contribute to areas of user experience and pervasive gaming.

Development of an autonomous unmanned aerial system to collect time-stamped samples from the atmosphere and localize potential pathogen sources

This paper presents the hardware development and testing of a new concept for air sampling via the integration of a prototype spore trap onboard an unmanned aerial system (UAS).We propose the integration of a prototype spore trap onboard a UAS to allow multiple capture of spores of pathogens in single remote locations at high or low altitude, otherwise not possible with stationary sampling devices.We also demonstrate the capability of this system for the capture of multiple time-stamped samples during a single mission.Wind tunnel testing was followed by simulation, and flight testing was conducted to measure and quantify the spread during simulated airborne air sampling operations. During autonomous operations, the onboard autopilot commands the servo to rotate the sampling device to a new indexed location once the UAS vehicle reaches the predefined waypoint or set of waypoints (which represents the region of interest). Time-stamped UAS data are continuously logged during the flight to assist with analysis of the particles collected. Testing and validation of the autopilot and spore trap integration, functionality, and performance is described. These tools may enhance the ability to detect new incursions of spores

Reactive image-based collision avoidance system for unmanned aircraft systems

Approximately 20 years have passed now since the NTSB issued its original recommendation to expedite development, certification and production of low-cost proximity warning and conflict detection systems for general aviation [1]. While some systems are in place (TCAS [2]), ¡¨see-and-avoid¡¨ remains the primary means of separation between light aircrafts sharing the national airspace. The requirement for a collision avoidance or sense-and-avoid capability onboard unmanned aircraft has been identified by leading government, industry and regulatory bodies as one of the most significant challenges facing the routine operation of unmanned aerial systems (UAS) in the national airspace system (NAS) [3, 4]. In this thesis, we propose and develop a novel image-based collision avoidance system to detect and avoid an upcoming conflict scenario (with an intruder) without first estimating or filtering range. The proposed collision avoidance system (CAS) uses relative bearing ƒÛ and angular-area subtended ƒê , estimated from an image, to form a test statistic AS C . This test statistic is used in a thresholding technique to decide if a conflict scenario is imminent. If deemed necessary, the system will command the aircraft to perform a manoeuvre based on ƒÛ and constrained by the CAS sensor field-of-view. Through the use of a simulation environment where the UAS is mathematically modelled and a flight controller developed, we show that using Monte Carlo simulations a probability of a Mid Air Collision (MAC) MAC RR or a Near Mid Air Collision (NMAC) RiskRatio can be estimated. We also show the performance gain this system has over a simplified version (bearings-only ƒÛ ). This performance gain is demonstrated in the form of a standard operating characteristic curve. Finally, it is shown that the proposed CAS performs at a level comparable to current manned aviations equivalent level of safety (ELOS) expectations for Class E airspace. In some cases, the CAS may be oversensitive in manoeuvring the owncraft when not necessary, but this constitutes a more conservative and therefore safer, flying procedures in most instances.

Comparative study of DFSS in product and service innovation

Six sigma has proven itself as a major quality initiative in the last two decades. It is a philosophy which provides a systematic approach to applying numerous tools in the framework of several quality improvement methodologies. The most widely used six sigma methodology is DMAIC, which is best suited for improving existing processes. In order to build quality into the product or service, a proactive approach like Design for Six Sigma (DFSS) is required. This paper provides an overview of DFSS, product innovation, and service innovation. The emphasis is on comparing how DFSS is applied differently in product and service innovation. This paper contributes by analysing the existing literature on DFSS in product and service innovation. The major findings are that the DFSS approach in services and products can be differentiated along the following three dimensions: methodology, characteristics, and technology.

Applying six-sigma in the service industry: a review and case study in call center services

This paper presents an extensive review on the services, six-sigma, and application of six-sigma in services. In order to improve service quality focus on service process is necessary. Six-sigma is a philosophy which also concentrates on the improvement of process. So, six-sigma if properly applied can be useful for services. This study focuses on the application aspect of six-sigma to wider range of services. The wider applicability of six-sigma depends on identification of key performance indicators(KPIs) for different types of service processes. A case study is conducted in call center services to identify, analyze and compare critical to quality characteristics (CTQs) and KPIs with other types of services available in literature. This study will be helpful to both practitioners and researchers.