Flerskiktat papper : en sammanställning av historia, teknik och forskningsresultat

Until the beginning of the 1900:th century the paper making process was handicraft. The paper machines that have been developed since then are as impressing in size as fascinating when it comes to the technique. The process has always been improved to give a better paper for lower costs, with as short manufacture time as possible. Stratified forming has been a reality since 1830. From the beginning it was applied to board and paperboard. Now it is also the most common method for making tissue and one paper mill in Austria use it for fine paper. Stratified forming can be categorized as separate forming or simultaneous forming. Separate forming means using several headboxes and sometimes even several wires. Simultaneous forming means using only one stratified headbox. This method has many advantages over separate forming, inter alia improved economy, quality, wood exchange and higher runability of the paper machine. Several experiments have been done with simultaneous forming of different fibres by placing a fibre with high bulk in the middle layer and a smooth fibre on the surface layers. The results has shown that by using this method both the bending stiffness and surface properties are improved, or a lower grammage paper is obtained with maintaining quality. Simultaneous forming can also be used to stratify fillers in layers where they are most efficient. In that way both paper quality and economy is improved. Simultaneous forming is also used for fractionated pulp. Fractionation means separating springwood fibre from summerwood fibre, and placing them in separate layers. Research results of fractionated pulp show about the same result as simultaneous forming of different fibres.

Vedegenskaper i härskande och behärskade granar vid Remingstorp : Wood properties in dominant and sub-dominant trees of Norway spruce at Remingstorp

Variation in wood properties for Picea abies trees and logs of different dimensions has been studied at two sites in southern Sweden of different site quality class. Trees have been classified as dominant or sub-dominant, according to their height. Log and board grades were classified and strength grade of boards, basic density and annual ring width measured. A similar study made on four northern sites was used as reference material.Sub-dominant trees were of superior quality in comparison to dominant trees, when classified by log and board grades or strength grading. Differences were accentuated for the second log where the sub-dominant trees had superior strength and low amount of boards with coarse branches. The results correspond well to those from the northern region, Jämtland. The classifica¬tion of boards as well as bending strength indicated superior properties on timber from northern sites even though the basic density was similar.

Methodology for identifying parameters for the TRNSYS model Type 210 -wood pellet stoves and boilers

This report describes a method how to perform measurements on boilers and stoves and how to identify parameters from the measurements for the boiler/stove-model TRNSYS Type 210. The model can be used for detailed annual system simulations using TRNSYS. Experience from measurements on three different pellet stoves and four boilers were used to develop this methodology. Recommendations for the set up of measurements are given and the re-quired combustion theory for the data evaluation and data preparation are given. The data evalua-tion showed that the uncertainties are quite large for the measured flue gas flow rate and for boilers and stoves with high fraction of energy going to the water jacket also the calculated heat rate to the room may have large uncertainties. A methodology for the parameter identification process and identified parameters for two different stoves and three boilers are given. Finally the identified models are compared with measured data showing that the model generally agreed well with meas-ured data during both stationary and dynamic conditions.

A study of slag corrosion of oxides and oxide-carbon refractories during steel refining

The use of ceramic material as refractories in the manufacturing industry is a common practice worldwide. During usage, for example in the production of steel, these materials do experience severe working conditions including high temperatures, low pressures and corrosive environments. This results in lowered service lives and high consumptions of these materials. This, in turn, affects the productivity of the whole steel plant and thereby the cost. In order to investigate how the service life can be improved, studies have been carried out for refractories used in the inner lining of the steel ladles. More specifically, from the slag zone, where the corrosion is most severe. By combining thermodynamic simulations, plant trails and post-mortem studies of the refractories after service, vital information about the behaviour of the slagline refractories during steel refining and the causes of the accelerated wear in this ladle area has been achieved. The results from these studies show that the wear of the slagline refractories of the ladle is initiated at the preheating station, through reduction-oxidation reactions. The degree of the decarburization process is mostly dependent on the preheating fuel or the environment. For refractories without antioxidants, refractory decarburization is slower when coal gas is used in ladle preheating than when a mixture of oil and air is used. In addition, ladle preheating of the refractories without antioxidants leads to direct wear of the slagline refractories. This is due to the total loss of the matrix strength, which results in a sand-like product. Thermal chemical changes that take place in the slagline refractories are due to the MgO-C reaction as well as the formation of liquid phases from impurity oxides. In addition, the decrease in the system pressure during steel refining makes the MgO-C reaction take place at the steel refining temperatures. This reduces the refractory’s resistance to corrosion. This is a serious problem for both the magnesia-carbon and dolomite-carbon refractories. The studies of the reactions between the slagline refractories and the different slag compositions showed that slags rich in iron oxide lead mostly to the oxidation of carbon/graphite in the carbon-containing refractories. This leads to an increased porosity and wettability and therefore an enhanced penetration of slag into the refractory structure. If the slag contains high contents of alumina and or silica (such as the steel refining slag), reactions between the slag components and the dolomite-carbon refractory are promoted. This leads to the formation of low-temperature melting phases such as calcium-aluminates and silicates. The state of these reaction products during steel refining leads to an accelerated wear of the dolomite-carbon refractory. The main products of the reactions between the magnesia-carbon refractory and the steel refining slag are MgAl2O4 spinels, and calcium-aluminates, and silicates. Due to the good refractory properties of MgAl2O4 spinels, the slag corrosion resistance of the magnesiacarbon refractory is promoted.

Emissions from realistic operation of residential wood pellets heating systems

Emissions from residential combustion appliances vary significantly depending on the firing behaviours and combustion conditions, in addition to combustion technologies and fuel quality. Although wood pellet combustion in residential heating boilers is efficient, the combustion conditions during start-up and stop phases are not optimal and produce significantly high emissions such as carbon monoxide and hydrocarbon from incomplete combustion. The emissions from the start-up and stop phases of the pellet boilers are not fully taken into account in test methods for ecolabels which primarily focus on emissions during operation on full load and part load. The objective of the thesis is to investigate the emission characteristics during realistic operation of residential wood pellet boilers in order to identify when the major part of the annual emissions occur. Emissions from four residential wood pellet boilers were measured and characterized for three operating phases (start-up, steady and stop). Emissions from realistic operation of combined solar and wood pellet heating systems was continuously measured to investigate the influence of start-up and stop phases on total annual emissions. Measured emission data from the pellet devices were used to build an emission model to predict the annual emission factors from the dynamic operation of the heating system using the simulation software TRNSYS. Start-up emissions are found to vary with ignition type, supply of air and fuel, and time to complete the phase. Stop emissions are influenced by fan operation characteristics and the cleaning routine. Start-up and stop phases under realistic operation conditions contribute 80 – 95% of annual carbon monoxide (CO) emission, 60 – 90% total hydrocarbon (TOC), 10 – 20% of nitrogen oxides (NO), and 30 – 40% particles emissions. Annual emission factors from realistic operation of tested residential heating system with a top fed wood pelt boiler can be between 190 and 400 mg/MJ for the CO emissions, between 60 and 95 mg/MJ for the NO, between 6 and 25 mg/MJ for the TOC, between 30 and 116 mg/MJ for the particulate matter and between 2x10-13 /MJ and 4x10-13 /MJ for the number of particles. If the boiler has the cleaning sequence with compressed air such as in boiler B2, annual CO emission factor can be up to 550 mg/MJ. Average CO, TOC and particles emissions under realistic annual condition were greater than the limits values of two eco labels. These results highlight the importance of start-up and stop phases in annual emission factors (especially CO and TOC). Since a large or dominating part of the annual emissions in real operation arise from the start-up and stop sequences, test methods required by the ecolabels should take these emissions into account. In this way it will encourage the boiler manufacturers to minimize annual emissions. The annual emissions of residential pellet heating system can be reduced by optimizing the number of start-ups of the pellet boiler. It is possible to reduce up to 85% of the number of start-ups by optimizing the system design and its controller such as switching of the boiler pump after it stops, using two temperature sensors for boiler ON/OFF control, optimizing of the positions of the connections to the storage tank, increasing the mixing valve temperature in the boiler circuit and decreasing the pump flow rate. For 85 % reduction of start-ups, 75 % of CO and TOC emission factors were reduced while 13% increase in NO and 15 % increase in particle emissions was observed.

Wood : from the forest to the consumer

Illegal logging causes a number of environmental and social damages in countries where wood is sourced from native forests. Logging in protected areas is an act of irresponsibility that exacerbates the loss of biodiversity. In addition, uncontrolled deforestation and bushfires may aggravate climate change, not to mention the negative effects they impose on local populations, such as the impoverishment of rural communities whose livelihoods depend on forest products. Several studies show that Brazil ranks high in terms of irresponsible use of natural resources, including native wood from the Amazon. Even more worrisome is the fact that the state, despite being responsible for regulating logging activities, is one of the largest consumers of native wood, which subverts the goals of any government committed to sustainable environmental management. By monitoring the development and impacts of illegal timber production and consumption around the world, the Friends of the Amazon Network – an initiative by the Getulio Vargas Foundation with support from the British Government and the European Commission – identified a need to describe and evaluate, in a brief and instructive manner, the different mechanisms the state has available to reverse this predatory practice. One of the aspects discussed in this book is the role of civil servants in major efforts aimed at repressing illegal logging and timber production, as well as identifying products derived from these activities in order to prevent their consumption. This is the purpose of this publication, which uses detailed infographics and a journalistic approach, including interviews and true stories, to outline the complexity of Amazon timber’s chain of custody – from logging, processing and transportation to commercialization in the Brazilian market.

Optimisation of solid-phase microextraction combined with gas chromatography–mass spectrometry based methodology to establish the global volatile signature in pulp and skin of Vitis vinifera L. grape varieties

The volatiles (VOCs) and semi-volatile organic compounds (SVOCs) responsible for aroma are mainly present in skin of grape varieties. Thus, the present investigation is directed towards the optimisation of a solvent free methodology based on headspace-solid-phase microextraction (HS-SPME) combined with gas chromatography–quadrupole mass spectrometry (GC–qMS) in order to establish the global volatile composition in pulp and skin of Bual and Bastardo Vitis vinifera L. varieties. A deep study on the extraction-influencing parameters was performed, and the best results, expressed as GC peak area, number of identified compounds and reproducibility, were obtained using 4 g of sample homogenised in 5 mL of ultra-pure Milli-Q water in a 20 mL glass vial with addition of 2 g of sodium chloride (NaCl). A divinylbenzene/carboxen/polydimethylsiloxane fibre was selected for extraction at 60 °C for 45 min under continuous stirring at 800 rpm. More than 100 VOCs and SVOCs, including 27 monoterpenoids, 27 sesquiterpenoids, 21 carbonyl compounds, 17 alcohols (from which 2 aromatics), 10 C13 norisoprenoids and 5 acids were identified. The results showed that, for both grape varieties, the levels and number of volatiles in skin were considerably higher than those observed in pulp. According to the data obtained by principal component analysis (PCA), the establishment of the global volatile signature of grape and the relationship between different part of grapes—pulp and skin, may be an useful tool to winemaker decision to define the vinification procedures that improves the organoleptic characteristics of the corresponding wines and consequently contributed to an economic valorization and consumer acceptance.

Modificações na produtividade e nas características físicas e químicas da madeira de Eucalyptus grandis causadas pela adubação com lodo de esgoto tratado

O Eucalyptus grandis é uma das espécies mais cultivadas no Brasil devido à sua produtividade e qualidade da madeira. Avaliaram-se o efeito da aplicação de lodo de esgoto tratado (0 a 40 t ha-1 base seca) e uma dose de adubo mineral nos atributos físicos e químicos da madeira de Eucalyptus grandis de árvores com cinco anos de idade, no Município de Itatinga, São Paulo, Brasil. O tipo de solo foi caracterizado como Latossolo Vermelho-Amarelo Distrófico (argila = 120 g kg-1 na camada de 0-20 cm) e o clima, como mesotérmico úmido (Cwa), segundo a classificação de Köeppen. O delineamento experimental foi o de blocos ao acaso, com seis tratamentos e quatro repetições. O diâmetro à altura do peito (DAP), a altura das árvores e o volume de madeira foram obtidos em todas as parcelas de oito árvores com DAP na classe de maior freqüência. As caracterizações físicas e químicas da madeira foram realizadas de acordo com as normas da ABTCP, TAPPI e ABNT. O lodo de esgoto diminuiu a densidade básica da madeira, mas não afetou os teores de celulose, lignina, extrativos e o poder calorífico da madeira. O decréscimo de densidade da madeira pela adubação com lodo de esgoto foi compensado pela maior produtividade de madeira.

Pseudomonas aeruginosa LBI production as an integrated process using the wastes from sunflower-oil refining as a substrate

Pseudomonas aeruginosa LBI produced surface active rhamnolipids when cultivated on waste from the sunflower-oil process under different conditions. These biosurfactants, which reduce the superficial and interfacial tensions between fluids, offer advantages over their chemical counterparts, especially because of their ecological acceptability. These molecules can be used in fields as diverse as chemical, pharmaceutical and petrochemical industries. In this work, we present the effect of C/N ratio on growth and production yield. The best production yields (Y-P/S) were achieved for C/N ratios (in g/g) of 8/1 (0.22) and 6.4/1 (0.23). The product concentration was very satisfactory (7.3 g/L) at C/N ratio of 8/1, especially when considering that the substrate was basically composed of wastes that would otherwise constitute an environmental disposal problem. (c) 2007 Elsevier Ltd. All rights reserved.

Hypolipemic and antioxidant activities from Tamarindus indica L. pulp fruit extract in hypercholesterolemic hamsters

Dietary modifications may significantly reduce cardiovascular disease (CVD) risk factors, including cholesterol and atherosclerosis. The present study addressed the effects of the crude extract from the pulp fruit of Tamarindus indica L. on lipid serum levels and early atherosclerotic lesions in hypercholesterolemic hamsters in vivo, and the extract's antioxidant action, in vitro. Animals were fed on either chow or atherogenic diet during 10 weeks and concomitantly received either water or T indica L. extract for drinking. Treatment of hypercholesterolemic hamsters with the T. indica pulp fruit extract (5%) led to a decrease in the levels of serum total cholesterol (50%), non-HDL cholesterol (73%) and triglyceride (60%), and to an increase of high-density lipoprotein (HDL) cholesterol levels (61%). In vitro, the extract presented radical scavenging ability, as assessed by the 2,2-diphenyl-1-picrylhydrazyl (DPPH) and superoxide radicals assays, and led to decreased lipid peroxidation in serum, as assessed by the thiobarbituric acid reactive substances (TBARS) assay. In vivo, the extract improved the efficiency of the antioxidant defense system, as assessed by the superoxide dismutase, catalase and glutathione peroxidase activities. Together these results indicate the potential of tamarind extracts in diminishing the risk of atherosclerosis development in humans. (c) 2005 Elsevier Ltd. All rights reserved.

Fermentative and microbiological profile of marandu-grass ensiled with citrus pulp pellets

Forragens com alta umidade e baixa concentração de carboidratos solúveis, como é o caso dos capins tropicais, podem conduzir a condições desfavoráveis para a produção de silagens de qualidade satisfatória. Esse estudo objetivou conhecer o perfil fermentativo e microbiológico de silagens de capim-Marandu [Brachiaria brizantha (Hochst ex. A. Rich) Stapf cv. Marandu], colhido com 58 dias de crescimento, aditivadas com polpa cítrica peletizada (PCP),. Foram utilizados silos experimentais de PVC adaptados com válvula do tipo Bunsen, tendo a silagem atingindo densidade de 900 kg m-3. Os tratamentos foram constituídos por três proporções de PCP (0, 50 e 100 g kg-1 em relação a matéria natural) e sete tempos de abertura após a ensilagem (1, 4, 7, 14, 21, 28 e 56 dias). A presença de PCP aumentou os teores de CHOs em 15 a 20%, reduziu o pH (5,3 para 4,2) e diminuiu as concentrações de N-NH3. Houve crescimento da população de enterobactérias somente durante o primeiro dia de fermentação (média 3 UFC g-1), pequeno desenvolvimento de clostrideos (média 0,5 UFC g-1) e dominância de bactérias homo em relação às heterofermentativas, para os três tratamentos estudados. A adição de polpa cítrica durante a ensilagem do capim-Marandu foi benéfica, podendo ser recomendada desde que haja benefício econômico na sua adoção.