Recycling of end of life concrete fines (0 - 4 mm) into silica and cement

The purpose of this work is to find a methodology in order to make possible the recycling of fines (0 - 4 mm) in the Construction and Demolition Waste (CDW) process. At the moment this fraction is a not desired by-product: it has high contaminant content, it has to be separated from the coarse fraction, because of its high water absorption which can affect the properties of the concrete. In fact, in some countries the use of fines recycled aggregates is highly restricted or even banned. This work is placed inside the European project C2CA (from Concrete to Cement and Clean Aggregates) and it has been held in the Faculty of Civil Engineering and Geosciences of the Technical University of Delft, in particular, in the laboratory of Resources And Recycling. This research proposes some procedures in order to close the loop of the entire recycling process. After the classification done by ADR (Advanced Dry Recovery) the two fractions "airknife" and "rotor" (that together constitute the fraction 0 - 4 mm) are inserted in a new machine that works at high temperatures. The temperatures analysed in this research are 600 °C and 750 °C, cause at that temperature it is supposed that the cement bounds become very weak. The final goal is "to clean" the coarse fraction (0,250 - 4 mm) from the cement still attached to the sand and try to concentrate the cement paste in the fraction 0 - 0,250 mm. This new set-up is able to dry the material in very few seconds, divide it into two fractions (the coarse one and the fine one) thanks to the air and increase the amount of fines (0 - 0,250 mm) promoting the attrition between the particles through a vibration device. The coarse fraction is then processed in a ball mill in order to improve the result and reach the final goal. Thanks to the high temperature it is possible to markedly reduce the milling time. The sand 0 - 2 mm, after being heated and milled is used to replace 100% of norm sand in mortar production. The results are very promising: the mortar made with recycled sand reaches an early strength, in fact the increment with respect to the mortar made with norm sand is 20% after three days and 7% after seven days. With this research it has been demonstrated that once the temperature is increased it is possible to obtain a clean coarse fraction (0,250 - 4 mm), free from cement paste that is concentrated in the fine fraction 0 - 0,250 mm. The milling time and the drying time can be largely reduced. The recycled sand shows better performance in terms of mechanical properties with respect to the natural one.

The Role of the Family in Shaping Self-Concept and Cognitive Styles in Hungary

The project studied the perception of parenting styles and their relation to self-development, cognitive styles, and individualisation in adolescence. Typical parenting styles of mothers and fathers were studied in five different maternal and paternal parenting backgrounds: warm authoritarian, warm democratic, cold neglectful, cold authoritarian, and neutral. Perception of different styles of parenting (for fathers: authority, 'maintaining distance' behaviour, reciprocity, enhancing self-reliance; for mothers: authority, unpredictable behaviour, mutual trust, achievement orientation, and enhancing self-reliance) were analysed in each group using the newly developed Hungarian Parenting Questionnaire (Sallay & Munnich, 1999). This questionnaire has a theoretical basis in the ideas of Harvey (1966, 1967), where the socialisation process is combined with self-development. This categorisation of paternal and maternal parenting backgrounds enabled Sallay to explore and describe in detail how diverse parenting styles contribute to self-development, the development of cognitive complexity, and individualisation. The results show that diverse parenting by mothers and fathers produces differing impacts in nuclear and divorced families and for males and females, taking into consideration such self-components as physical, active, psychological (capabilities, personality, emotions, roles, preferences), social and reflective selves. Cognitive self-complexity varied according to parenting styles and genders: maternal and paternal parenting proved to have the most significant impact on self-complexity in a warm, democratic family. With respect to individualistic tendencies, adolescent boys were most individualistic in a cold, neglectful paternal background in nuclear families as compared to other paternal and maternal family backgrounds and to females.

Learning styles vary among general surgery residents: analysis of 12 years of data

PURPOSE: Understanding the learning styles of individuals may assist in the tailoring of an educational program to optimize learning. General surgery faculty and residents have been characterized previously as having a tendency toward particular learning styles. We seek to understand better the learning styles of general surgery residents and differences that may exist within the population. METHODS: The Kolb Learning Style Inventory was administered yearly to general surgery residents at the University of Cincinnati from 1994 to 2006. This tool allows characterization of learning styles into 4 groups: converging, accommodating, assimilating, and diverging. The converging learning style involves education by actively solving problems. The accommodating learning style uses emotion and interpersonal relationships. The assimilating learning style learns by abstract logic. The diverging learning style learns best by observation. Chi-square analysis and analysis of variance were performed to determine significance. RESULTS: Surveys from 1994 to 2006 (91 residents, 325 responses) were analyzed. The prevalent learning style was converging (185, 57%), followed by assimilating (58, 18%), accommodating (44, 14%), and diverging (38, 12%). At the PGY 1 and 2 levels, male and female residents differed in learning style, with the accommodating learning style being relatively more frequent in women and assimilating learning style more frequent in men (Table 1, p < or = 0.001, chi-square test). Interestingly, learning style did not seem to change with advancing PGY level within the program, which suggests that individual learning styles may be constant throughout residency training. If a resident's learning style changed, it tended to be to converging. In addition, no relation exists between learning style and participation in dedicated basic science training or performance on the ABSIT/SBSE. CONCLUSIONS: Our data suggests that learning style differs between male and female general surgery residents but not with PGY level or ABSIT/SBSE performance. A greater understanding of individual learning styles may allow more refinement and tailoring of surgical programs.

How to Improve the Production Process for interactive TV with semi-formal Methods

The central question for this paper is how to improve the production process by closing the gap between industrial designers and software engineers of television(TV)-based User Interfaces (UI) in an industrial environment. Software engineers are highly interested whether one UI design can be converted into several fully functional UIs for TV products with different screen properties. The aim of the software engineers is to apply automatic layout and scaling in order to speed up and improve the production process. However, the question is whether a UI design lends itself for such automatic layout and scaling. This is investigated by analysing a prototype UI design done by industrial designers. In a first requirements study, industrial designers had created meta-annotations on top of their UI design in order to disclose their design rationale for discussions with software engineers. In a second study, five (out of ten) industrial designers assessed the potential of four different meta-annotation approaches. The question was which annotation method industrial designers would prefer and whether it could satisfy the technical requirements of the software engineering process. One main result is that the industrial designers preferred the method they were already familiar with, which therefore seems to be the most effective one although the main objective of automatic layout and scaling could still not be achieved.

A continuous-time MILP model for short-term scheduling of make-and-pack production processes

In process industries, make-and-pack production is used to produce food and beverages, chemicals, and metal products, among others. This type of production process allows the fabrication of a wide range of products in relatively small amounts using the same equipment. In this article, we consider a real-world production process (cf. Honkomp et al. 2000. The curse of reality – why process scheduling optimization problems are diffcult in practice. Computers & Chemical Engineering, 24, 323–328.) comprising sequence-dependent changeover times, multipurpose storage units with limited capacities, quarantine times, batch splitting, partial equipment connectivity, and transfer times. The planning problem consists of computing a production schedule such that a given demand of packed products is fulfilled, all technological constraints are satisfied, and the production makespan is minimised. None of the models in the literature covers all of the technological constraints that occur in such make-and-pack production processes. To close this gap, we develop an efficient mixed-integer linear programming model that is based on a continuous time domain and general-precedence variables. We propose novel types of symmetry-breaking constraints and a preprocessing procedure to improve the model performance. In an experimental analysis, we show that small- and moderate-sized instances can be solved to optimality within short CPU times.

Comparison of clinical knowledge management capabilities of commercially-available and leading internally-developed electronic health records.

BACKGROUND: We have carried out an extensive qualitative research program focused on the barriers and facilitators to successful adoption and use of various features of advanced, state-of-the-art electronic health records (EHRs) within large, academic, teaching facilities with long-standing EHR research and development programs. We have recently begun investigating smaller, community hospitals and out-patient clinics that rely on commercially-available EHRs. We sought to assess whether the current generation of commercially-available EHRs are capable of providing the clinical knowledge management features, functions, tools, and techniques required to deliver and maintain the clinical decision support (CDS) interventions required to support the recently defined "meaningful use" criteria. METHODS: We developed and fielded a 17-question survey to representatives from nine commercially available EHR vendors and four leading internally developed EHRs. The first part of the survey asked basic questions about the vendor's EHR. The second part asked specifically about the CDS-related system tools and capabilities that each vendor provides. The final section asked about clinical content. RESULTS: All of the vendors and institutions have multiple modules capable of providing clinical decision support interventions to clinicians. The majority of the systems were capable of performing almost all of the key knowledge management functions we identified. CONCLUSION: If these well-designed commercially-available systems are coupled with the other key socio-technical concepts required for safe and effective EHR implementation and use, and organizations have access to implementable clinical knowledge, we expect that the transformation of the healthcare enterprise that so many have predicted, is achievable using commercially-available, state-of-the-art EHRs.

Measurements of Higgs boson production and couplings in diboson final states with the ATLAS detector at the LHC

Measurements are presented of production properties and couplings of the recently discovered Higgs boson using the decays into boson pairs, H --> gamma-gamma, H --> ZZ* --> 4 leptons and H --> WW --> 2 leptons + 2 neutrinos. The results are based on the complete pp collision data sample recorded by the ATLAS experiment at the CERN Large Hadron Collider at centre-of-mass energies of 7 TeV and 8 TeV, corresponding to an integrated luminosity of about 25/fb. Evidence for Higgs boson production through vector-boson fusion is reported. Results of combined fits probing Higgs boson couplings to fermions and bosons, as well as anomalous contributions to loop-induced production and decay modes, are presented. All measurements are consistent with expectations for the Standard Model Higgs boson.

Scheduling the production of rolling ingots: Industrial context, model, and solution method

We study a real-world scheduling problem arising in the context of a rolling ingots production. First we review the production process and discuss peculiarities that have to be observed when scheduling a given set of production orders on the production facilities. We then show how to model this scheduling problem using prescribed time lags between operations, different kinds of resources, and sequence-dependent changeovers. A branch-and-bound solution procedure is presented in the second part. The basic principle is to relax the resource constraints by assuming infinite resource availability. Resulting resource conflicts are then stepwise resolved by introducing precedence relationships among operations competing for the same resources. The algorithm has been implemented as a beam search heuristic enumerating alternative sets of precedence relationships.

Analysis of the mechanisms that maintain coordinate production of $\alpha$- and $\beta$-tubulin in mammalian cells

Alpha and beta tubulin are essential proteins in all eukaryotic cells. To study how cells maintain coordinate levels of these two interacting proteins, we have used PCR to add a 9 amino acid epitope from influenza hemagglutinin protein onto the carboxyl terminus of $\alpha$1 and $\beta$1-tubulin. The chimeric tubulin genes (HA$\alpha$1 and HA$\beta$1) were transfected into CHO cells and cell lines that stably express each gene were selected. Cells transfected with HA-tubulin do not exhibit any gross changes in growth or morphology. Immunofluorescence analysis demonstrated that HA-tubulins incorporate into both cytoplasmic and spindle microtubules. A quantitative biochemical assay was used to show that HA-tubulins incorporate into microtubules to a normal extent and do not alter the steady state distribution of endogenous tubulin between monomer and polymer pools. Two-dimensional gel analysis of pulse-labeled cells indicated that when HA$\beta$1-tubulin is expressed at high levels, it slightly represses the synthesis of the endogenous $\beta$-tubulin but produces a small increase in the synthesis of $\alpha$-tubulin. Analysis of cells labeled to steady state showed that HA$\beta$1-tubulin accumulates to a similar level as the wild-type gene product, but together these polypeptides produce only a small increase in total tubulin content consistent with the increased synthesis of $\alpha$-tubulin. It thus appears that HA$\beta$1-tubulin successfully competes with endogenous $\beta$-tubulin for heterodimer formation and that free $\beta$-tubulin subunits (endogenous and HA$\beta$1) are selectively degraded to maintain coordinate amounts of $\alpha$- and $\beta$-tubulin. In addition, the increased synthesis of $\alpha$-tubulin suggested the existence of a mechanism to ensure coordinate synthesis of $\alpha$- and $\beta$-tubulin subunits. To analyze whether reciprocal changes in endogenous tubulin synthesis occur when $\alpha$-tubulin is overexpressed, stably transfected CHO cell lines were isolated in which HA$\alpha$1-tubulin represents 50% of the total $\alpha$-tubulin, and its relative abundance can be further increased to 85-90% by treatment with sodium butyrate. In contrast with results obtained using HA$\beta$1-tubulin, transfection of HA$\alpha$1-tubulin decreased the synthesis of endogenous $\alpha$-tubulin to 60% of normal with little or no change in $\beta$-tubulin synthesis. When the transfected cells were treated with sodium butyrate to further increase HA$\beta$1-tubulin production, a larger decrease in the synthesis of endogenous $\alpha$-tubulin (to 30% of normal) was observed. The repression on the synthesis of endogenous $\alpha$-tubulin polypeptide was found to be directly proportional to the expression of HA$\alpha$1-tubulin indicating the existence of an autoregulatory loop, where $\alpha$-tubulin inhibits its own synthesis. To determine whether overproduction of HA$\alpha$1-tubulin affected the transcription, message stability or translation of endogenous $\alpha$-tubulin, the steady state levels of $\alpha$-tubulin mRNA were analyzed by ribonuclease protection assays. The results showed that the steady state level of $\alpha$-tubulin mRNA is not affected by the overexpression of HA$\alpha$1-tubulin, indicating that the repression is translational. The results are compatible with a model in which $\beta$-tubulin synthesis is largely unperturbed by overexpression of other tubulin subunits, and excess $\beta$-tubulin subunits are rapidly degraded to maintain coordinate $\alpha$- and $\beta$-tubulin levels at steady state. In contrast, free $\alpha$-tubulin represses its own synthesis at the translational level, suggesting that its level of production may be controlled by the amount of $\beta$-tubulin available for heterodimer formation. ^

Localization and production of peptide endocannabinoids in the rodent CNS and adrenal medulla.

The endocannabinoid system (ECS) comprises the cannabinoid receptors CB1 and CB2 and their endogenous arachidonic acid-derived agonists 2-arachidonoyl glycerol and anandamide, which play important neuromodulatory roles. Recently, a novel class of negative allosteric CB1 receptor peptide ligands, hemopressin-like peptides derived from alpha hemoglobin, has been described, with yet unknown origin and function in the CNS. Using monoclonal antibodies we now identified the localization of RVD-hemopressin (pepcan-12) and N-terminally extended peptide endocannabinoids (pepcans) in the CNS and determined their neuronal origin. Immunohistochemical analyses in rodents revealed distinctive and specific staining in major groups of noradrenergic neurons, including the locus coeruleus (LC), A1, A5 and A7 neurons, which appear to be major sites of production/release in the CNS. No staining was detected in dopaminergic neurons. Peptidergic axons were seen throughout the brain (notably hippocampus and cerebral cortex) and spinal cord, indicative of anterograde axonal transport of pepcans. Intriguingly, the chromaffin cells in the adrenal medulla were also strongly stained for pepcans. We found specific co-expression of pepcans with galanin, both in the LC and adrenal gland. Using LC-MS/MS, pepcan-12 was only detected in non-perfused brain (∼40 pmol/g), suggesting that in the CNS it is secreted and present in extracellular compartments. In adrenal glands, significantly more pepcan-12 (400-700 pmol/g) was measured in both non-perfused and perfused tissue. Thus, chromaffin cells may be a major production site of pepcan-12 found in blood. These data uncover important areas of peptide endocannabinoid occurrence with exclusive noradrenergic immunohistochemical staining, opening new doors to investigate their potential physiological function in the ECS. This article is part of a Special Issue entitled 'Fluorescent Neuro-Ligands'.

Pottery as an indication of mobilities?

Pottery is one of the most common and stylistically differentiated sources in prehistoric archaeology. This might be the reason why it served as a waste projection surface for archaeological notions about culture, identity, and mobility in the past. As we do not have access to emic categorisations of Neolithic societies we focus on contexts of practice in which pottery was incorporated. It is the moment of production, which left some of the clearest traces on the vessels. Different ways of using raw materials, specific techniques, and characteristic pottery styles can be observed. We understand them as a result of habitus, as socially shared internalized schemes, patterns and habits in pottery production. Taking this as a staring point, two main pottery groups can be differed on the Swiss Plateau between 3900 and 3500 BC: the Mediterranean influenced Cortaillod pottery in Western Switzerland and the Danubian influenced Pfyn pottery in North-Eastern Switzerland. These pottery styles were not only entangled to some degree. Furthermore, in some settlements vessels made in “foreign” styles - Michelsberg, Munzingen, Néolithique Moyen Bourguignon - are present too. Some of them were travelling objects, as their nonlocal raw materials show. Others were locally made, indicating long-term mobility of their producers. To analyse these phenomena of mobilites and entanglements in our PhDs we plan to apply different archaeological and archaeometrical methods, thus striving for a deeper understanding of the transformative potential of moving people, objects and ideas in Neolithic societies on the Swiss Plateau.

The status of genetically modified foods internationally and in the United States

Biotechnology refers to the broad set of techniques that allow genetic manipulation of organisms. The techniques of biotechnology have broad implications for many industries, however it promises the greatest innovations in the production of products regulated by the Food and Drug Administration (FDA). Like many other powerful new technologies, biotechnology may carry risks as well as benefits. Several of its applications have engendered fervent emotional reactions and raised serious ethical concerns, especially internationally. ^ First, in my paper I discuss the historical and technical background of biotechnology. Second, I examine the development of biotechnology in Europe, the citizens' response to genetically modified (“GM”) foods and the governments' response. Third, I examine the regulation of bioengineered products and foods in the United States. ^ In conclusion, there are various problems with the current status of regulation of GM foods in the United States. These are four basic flaws: (1) the Coordinated Framework allows for too much jurisdictional overlap of biotechnological foods, (2) GM foods are considered GRAS and consequently, are placed on the market without pre-market approval, (3) federal mandatory labeling of GM foods cannot occur until the question of whether or not nondisclosure of a genetic engineering production processes is misleading or material information and (4) an independent state-labeling scheme of GM foods will most likely impede interstate commerce. ^

A qualitative analysis of leadership styles and the selection of quality improvement in primary care practice

In the Practice Change Model, physicians act as key stakeholders, people who have both an investment in the practice and the capacity to influence how the practice performs. This leadership role is critical to the development and change of the practice. Leadership roles and effectiveness are an important factor in quality improvement in primary care practices.^ The study conducted involved a comparative case study analysis to identify leadership roles and the relationship between leadership roles and the number and type of quality improvement strategies adopted during a Practice Change Model-based intervention study. The research utilized secondary data from four primary care practices with various leadership styles. The practices are located in the San Antonio region and serve a large Hispanic population. The data was collected by two ABC Project Facilitators from each practice during a 12-month period including Key Informant Interviews (all staff members), MAP (Multi-method Assessment Process), and Practice Facilitation field notes. This data was used to evaluate leadership styles, management within the practice, and intervention tools that were implemented. The chief steps will be (1) to analyze if the leader-member relations contribute to the type of quality improvement strategy or strategies selected (2) to investigate if leader-position power contributes to the number of strategies selected and the type of strategy selected (3) and to explore whether the task structure varies across the four primary care practices.^ The research found that involving more members of the clinic staff in decision-making, building bridges between organizational staff and clinical staff, and task structure are all associated with the direct influence on the number and type of quality improvement strategies implemented in primary care practice.^ Although this research only investigated leadership styles of four different practices, it will offer future guidance on how to establish the priorities and implementation of quality improvement strategies that will have the greatest impact on patient care improvement. ^

AN EMPIRICAL ESTIMATION OF MEDICAL AND NON-MEDICAL INPUTS IN THE PRODUCTION OF CARDIO-RESPIRATORY PHYSICAL HEALTH STATUS

The purpose of this study was to examine, in the context of an economic model of health production, the relationship between inputs (health influencing activities) and fitness.^ Primary data were collected from 204 employees of a large insurance company at the time of their enrollment in an industrially-based health promotion program. The inputs of production included medical care use, exercise, smoking, drinking, eating, coronary disease history, and obesity. The variables of age, gender and education known to affect the production process were also examined. Two estimates of fitness were used; self-report and a physiologic estimate based on exercise treadmill performance. Ordinary least squares and two-stage least squares regression analyses were used to estimate the fitness production functions.^ In the production of self-reported fitness status the coefficients for the exercise, smoking, eating, and drinking production inputs, and the control variable of gender were statistically significant and possessed theoretically correct signs. In the production of physiologic fitness exercise, smoking and gender were statistically significant. Exercise and gender were theoretically consistent while smoking was not. Results are compared with previous analyses of health production. ^

As redes sociotécnicas da comunidade gamer : Habilidades cognitivas, capitalismo cognitivo e pirataria no orkut

In the perspective of the so called 'cognitive capitalism', this paper intends to analyze the sharing and customization strategies developed in Brazilian online game communities. Under Bruno Latour's Actor-Network Theory (ANT), this work describes these socio-technical networks electing the human and non human relevant actants for their role on what could also be depicted as an distributed cognitive process (HUTCHINS, 2000). This alternative way of participative consumption deals with the social and creative production of tutorials; in-game and out-game editing and all sorts of gathering, organization and distribution of virtual data. The communities studied are related to the game Pro Evolution Soccer (PES) in their multiple platforms