Study of SnO2 gels by Eu3+ fluorescence spectroscopy

Eu3+ fluorescence spectroscopy was used as a probe to study the changes in local arrangements of tin oxyhydroxide precipitate → sol → gel → glass conversion. Electronic transition intensities and 5D0 excited state lifetime variations were followed during the entire process. Adsorption of Eu3+ ions on the colloid and changes of chemical interactions occurring in each step are described. © 1992 Elsevier Science Publishers B.V. All rights reserved.

Drying of SnO2 hydrogels: effect of the electrolyte

The effect of the electrolyte (NH+ 4, Cl-) on the drying of SnO2 hydrogels was investigated by linear shrinkage, mass loss, gravimetric thermal analysis and infrared spectroscopy. Results show that the drying mechanism for monolithic SnO2 gels is highly dependent on the concentration of the electrolyte solution inside the pores. For higher concentrations, the drying process is governed by capillary forces while for the smaller ones (≤20 mM) syneresis shrinkage becomes predominant just before the end of the first drying period. This phenomenon is related to condensation reaction among the superficial OH groups and may hamper formation of monolithic SnO2. © 1992 Elsevier Science Publishers B.V. All rights reserved.

Spectroscopic characterization of SnO2 gels - Code: CP11

Excitation and dynamic emission spectra of Eu3+ ions were simultaneously used with FTIR and Raman spectroscopy to study the structural evolution during SnO2 sol → gel → xerogel conversion. Results make evident an increase of the surroundings symmetry for the Eu3+ ions dissolved in SnO2 matrix and a decrease of the amount of hydroxo groups (Sn-OH) during drying. These phenomena were associated to the pursuit of the condensation reaction after gelation. © 1994 Kluwer Academic Publishers.

Pore size distribution of unsupported SnO2 membranes prepared by sol-gel process - Code: EP21

Unsupported SnO2 membranes were prepared by sol-gel process and characterized by N2 adsorption-desorption isotherms and X-ray diffraction. Results show that the texture of dried samples does not change appreciably with the concentration of electrolyte. All of the pore size range used in ultrafiltration process was screened using sintering temperature between 300 and 700°C. © 1994 Kluwer Academic Publishers.

Evolution of the fractal structure during sintering of SnO2 compacted sol-gel powder

The structural evolution during sintering of compacted SnO2 sol-gel powder was investigated using nitrogen adsorption isotherm analysis. Results show that for sintering temperatures up to 400°C the samples have a fractal pore size distribution. As the sintering temperature increases, a structural rearragement occurs, allowing an increase of the efficiency of particle packing and the reduction of fractality. Above 400°C, the pore size growth associated with grain coalescence is the main structural change observed as the sintering temperature increases. © 1995.

Time evolution of the structure function and dynamical scaling in porous SnO2 dry gels

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

EXAFS and XRD analyses of the structural evolutions involved during drying of SnO2 hydrogels

In order to determine structural changes during drying of inorganic gels, the local and long-range order structure of SnO2-x(OH)2x xerogels resulting from drying hydrogels with different concentrations of electrolyte (Cl- and NH+ 4) have been measured by extended X-ray absorption fine structure (EXAFS), X-ray diffraction (XRD) and N2 adsorption techniques. EXAFS measurements performed at the Sn K edge on the hydrogels and xerogels show the existence of microcrystallites with the cassiterite structure. Two drying modes have been used: freeze drying and drying by evaporation at 45°C. It is shown that the microcrystallite size determined by XRD and EXAFS techniques on the drying mode and on the electrolyte concentrations. The microcrystallite size measured on the freeze dried xerogels is similar to that of their parent hydrogels, whatever the concentration of electrolyte; however, during drying by evaporation, a preferential growth of microcrystallites along the c-axis of the cassiterite structure is observed. The size of these crystallites is enhanced with a decrease of the electrolyte concentration. Specific surface areas calculated by the Brunauer-Emmett-Teller method indicate that this preferential growth is related to the improvement of the network connectivity. The comparison of both drying processes indicates that crystallization and polycondensation are independent phenomena. © 1995 Elsevier Science B.V. All rights reserved.

Anisotropy of crystallite growth during sintering of SnO2 xerogels

The crytallite and pore-size evolution during isothermal sintering (400 ≤ T ≤ 700°C) of SnO2 xerogels was studied by X-ray line broadening and nitrogen adsorption-desorption isotherms. The experimental results show a strong anisotropy of crystallite growth between [110] and [101] directions. The preferential growth at [101] is followed by an increase in the mean pore size, reduction of the specific surface area and invariance of total pore volume. This behaviour is typical of grain coalescence sintering. The kinetic analysis of experimental results suggests that the crystallite coalescence at [101] is governed by lattice diffusion. The strong anisotropy of the growth causes pore-size distribution broadening, hindering the macroscopic shrinkage of the compact during sintering. © 1996 Chapman & Hall.

SAXS measurements of the porosity in Cu(II)-doped SnO2 xerogels during crystallization

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Short Range Order Evolution in the Preparation of SnO2 Based Materials

The evolution of Eu3+ doped SnO2 xerogels to the cassiterite structure observed during sintering was studied by means of Eu3+ spectroscopy, XRD and EXAFS at the Sn K-edge. Eu3+ ions adsorbed at the surface of colloidal particles present a broad distribution of sites, typical of oxide glasses. With sintering at 300°C, this distribution is still broadened. Crystallization is clearly observed by the three techniques with increasing sintering temperature. It is found that the addition of Eu3+ limits the crystallite growth.

Electrical and optical characteristics of SnO2 thin films prepared by dip coating from aqueous colloidal suspensions

Starting from aqueous colloidal suspensions, undoped and Nb5+ doped SnO2 thin films have been prepared by using the dip-coating sol gel process. X-ray diffraction results show that films are polycrystalline with crystallites of average size1-4nm. Decreasing the thickness of the films and increasing the Nb5+ concentration limits the crystallite size growth during firing. Complex impedance measurements reveal capacitive and resistive effects between adjacent crystallites or grains, characteristic of electrical potential barriers. The transfer of charge throughout these barriers determines the macroscopic electrical resistance of the layer. The analysis of the optical absorption spectra shows that the samples present more than 80% of their transmittance in the visible region and the value of the band gap energy increases with decreasing crystallite size. © 1997 Chapman & Hall.

EXAFS and XRD Study of the Structural Evolution during Isothermal Sintering of SnO2 Xerogels

The formation of an ordered (crystalline) phase during isothermal sintering of SnO2 monolithic xerogels, at 200, 250, 300, 400, 500, 600 and 700°C, has been analyzed by the combined use of EXAFS and XRD techniques. For the desiccated gel (110°C), EXAFS results show the formation of small microcrystallites with the incipient cassiterite structure. Between 110 and 250°C, the dehydratation reaction leads to an amorphization evidenced by a decrease of the long and short range crystallographic order. It is due to fissure formation in the xerogel network. For higher temperatures, a continuous coagulation of the crystallites occurs, leading to grain growth. Grain and pore growth obeys the same kinetic relation, so that the microstructure grows by simple enlargement while its morphology is static.

Influence of viscoelastic characteristics of the colloidal suspensions on the formation of SnO2 supported membranes

SnO2 supported membranes have been prepared by sol-casting on alumina tubular substrate, using aqueous colloidal suspensions prepared by sol-gel route. The viscoelastic behaviour during sol ageing was analyzed by dinamic rheologial measurements. The complex viscosity and the storage and loss moduli have been followed during the sol-gel transition and the results have been correlated with the linear aggregates growth and the scalar percolation models. The scanning electron microscopy has evidenced that the homogeneity and thickness of the membrane depend on the sol ageing time. Crack-free and homogeneous membranes have been obtained for coated layers of 0.5μm thickness. © 1997 Trans Tech Publications.

Electrical properties of the SnO2-based varistor

The non-linear electrical properties of CoO-doped and Nb205-doped SnO2 ceramics were characterized. X-ray diffraction and scanning electron microscopy indicated that the system is single phase. The electrical conduction mechanism for low applied electrical field was associated with thermionic emission of the Schottky type. An atomic defect model based on the Schottky double-barrier formation was proposed to explain the origin of the potential barrier at the ceramic grain boundaries. These defects create depletion layers at grain boundaries, favouring electron tunnelling at high values of applied electrical field. © 1998 Chapman & Hall.

Effect of atmosphere and dopants on sintering of SnO2

Tin oxide is an n-type semiconductor material with a high covalent behavior. Mass transport in this oxide depends on the surface state promoted by atmosphere or by the solid solution of a non-isovalent oxide doping The sintering and grain growth of this type of oxide powder is then controlled by atmosphere and by extrinsic oxygen vacancy formation. For pure SnO2 powder the surface state depends only on the interaction of atmosphere molecules with the SnO2 surface. Inert atmosphere like argon or helium promotes oxygen vacancy formation at the surface due to reduction of SnO2 to SnO at the surface and liberation of oxygen molecules forming oxygen vacancies. As consequence surface diffusion is enhanced leading to grain coarsening but no densification. Oxygen atmosphere inhibits the SnO2 reduction decreasing the surface oxygen vacancy concentration. Addition of dopants with lower valence at sintering temperature creates extrinsic charged oxygen vacancies that promote mass transport at grain boundary leading to densification and grain growth of this polycrystalline oxide.