Concentration of injetion solution and its effects on soil and on yield of fertirrigated banana cv. Terra Maranhão

The Fertigation is the combined application of water and nutrients to a crop. It can be adapted to all types of agricultural crops. The objective of this study was to evaluate the effect of urea concentration in irrigation water on electrical conductivity of the soil solution and saturation extract along the first cycle of banana cv. Terra Maranhão. The experiment followed a completely randomized design with six treatments and ten replications. Treatments regarded for using three urea concentrations (1.0; 2.5 and 4.0 g L-1) in irrigation water applied by two micro irrigation systems (microsprinkler and drip). Results showed that there was a linear elevation of electrical conductivity of saturation extract and soil solution with the increase on concentration of urea in the injection solution. Urea should be used under concentrations up to 2.5 g L-1 in irrigation water without causing increase on electric conductivity of soil solution and saturation extract, considering 1.1 dS m-1 as the tolerated value for the crop. Nitrate in the soil solution increased significantly with the increase of urea concentration in the injection solution. The maximum concentration of nitrate in the soil occurred for 4,0 g L-1 concentration of the injection solution.

Factors affecting immunoglobulin concentration in colostrum of healthy Holstein cows immediately after delivery

This study analyzed the influence of the number of milkings, number of births, and udder quarter in immunoglobulin (Ig) concentration in the colostrum of healthy Holstein cows. It was collected two samples of colostrum by manual milking, getting the first jets to completion of bacteriological examination and immunoglobulin levels by radial immunodiffusion test in agar gel. Positive samples for bacteriological examination were excluded from this investigation. Medians of immunoglobulin's G, A and M in the colostrum collected before the first and second milking were respectively 9,200 and 6,400mg/dL (p=0.0029); 400 and 200mg/dL (p=0.0018); 800 and 400mg/dL (p=0.0001). Median immunoglobulin concentration in animals that calved once, twice or three times or in cows that calved 4 to 6 times were 6,400; 6,400; 3,200 and 11,200mg/dL IgG; 100, 200, 100 and 800mg/dL IgA ; and 400, 400, 100 and 800mg/dL IgM, respectively. Concentrations of IgG, IgA and IgM were greater in animals that calved more than 4 times (p<0.05). Medians of IgG, IgA and IgM in the right fore quarter (RF), right hind quarter (RH), left fore quarter (LF) and left hind quarter (LH) were, respectively, 7,800; 6,400; 7,800 and 6,400mg/dL; 200, 200, 200 and 200mg/dL; and 400, 400, 400 and 400mg/dL. Ig concentrations in the colostrum of Holstein cows were influenced by the number of milkings after delivery and number of lactations. These variations may be considered risk factors to passive immunity transfer to newborn calves, predisposing them to diseases and causing economic losses to dairy production.

Renal cortex copper concentration in acute copper poisoning in calves

The aim of this study was to estimate the diagnostic value of renal cortex copper (Cu) concentration in clinical cases of acute copper poisoning (ACP). A total of 97 calves that died due to subcutaneous copper administration were compiled in eleven farms. At least, one necropsy was conducted on each farm and samples for complementary analysis were taken. The degree of autolysis in each necropsy was evaluated. The cases appeared on extensive grazing calf breeding and intensive feedlot farms, in calves of 60 to 200 kg body weight. Mortality varied from 0.86 to 6.96 %, on the farms studied. The first succumbed calf was found on the farms between 6 and 72 hours after the susbcutaneous Cu administration. As discrepancies regarding the reference value arose, the local value (19.9 parts per million) was used, confirming the diagnosis of acute copper poisoning in 93% of the analyzed kidney samples. These results confirm the value of analysis of the cortical kidney Cu concentration for the diagnosis of acute copper poisoning.

Porcine follicular fluid concentration of free insulin-like growth factor-I collected from different diameter ovarian follicles

The study aimed to quantify the concentrations of free IGF-I in serum and fluid of ovarian follicles in pre-pubertal gilts and describe the ovarian morphology by measuring the size of the ovaries and counting the number of surface follicles. Ovaries (n=1,000) from pre-pubertal gilts were obtained immediately after slaughter. A total of 10 samplings were performed, with ovaries obtained from 50 females for each collection. The follicles situated on the surface of each ovary were classified as small (SFs, 2 to 5mm in diameter) or large (LFs 6 to 10mm in diameter) and the follicular fluid was obtained by follicle aspiration. The collection of serum samples was performed after the gilts exsanguination using sterile tubes. From the pool of serum and follicular fluid obtained from 50 females, the concentration of free IGF-I was determined in each sample using an enzyme immunoassay kit (ELISA). The description of ovarian morphometry was performed in 100 ovaries from randomly selected gilts. The larger and smaller lengths of ovaries were measured, and the total number of SFs and LFs present on the surface of each ovary were also counted. The IGF-I concentration was greater (P<0.05) in LFs (170.92±88.29 ng/mL) compared with SFs (67.39±49.90ng/mL) and serum (73.48±34.63ng/mL). The largest and smallest length of the ovaries was 26.0±3.0 and 19.0mm ±2.0mm, respectively. The number of SFs (70.86±25.76) was greater (P<0.01) than LFs (6.54±5.26). The study concluded that LFs present greater levels of IGF-I when compared with SFs and blood, which is related to increased activity of the LFs and its differentiation to ovulation. In addition, ovaries of pre-pubertal gilts have a higher number of SFs compared to LFs. Therefore, our study demonstrated unique data regarding the physiological concentration of free IGF-I in ovarian follicles, that can be used in future research to evaluate the addition of this hormone in the in vitro production media of porcine embryos with the goal to improve the technique efficiency.

Relationship between weight, age and hatching success and the concentration of heavy metals in nestling blue macaw (Anodorhynchus hyacinthinus Latham, 1790) in the Pantanal,Mato Grosso do Sul

Abstract: The concentration of heavy metals (Cr, Fe, Al, As, Cd, Cu, Pb, Mo, Ni, Se and Zn) was evaluated in the blood of nestling blue macaws (Anodorhynchus hyacinthinus) captured in the Pantanal, Mato Grosso do Sul (n=26) in 2012; this was based on the hypothesis that these birds exhibit levels of these heavy metals in their organism and that these interfere in hatching success, weight and age of the chicks. Blood samples were digested with nitric acid and hydrochloric acid and the quantification of metals was performed by ICP-OES (Optical Emission Spectroscopy and Inductively Coupled Plasma). Blood samples of nestlings showed concentrations of Cr (0.10μg/g) Fe (3.06μg/g) Al (3.46μg/g), Cd (0.25μg/g) Cu (0.74μg/g), Mo (0.33μg/g), Ni (0.61μg/g), Se (0.98μg/g), and Zn (2.08μg/g). The levels of heavy metals found were not associated with weight, age and hatching success of the chicks.

The role of potassium in the corrosion of superheater materials in boilers firing biomass

Inhibition of global warming has become one of the major goals for the coming decades. A key strategy is to replace fossil fuels with more sustainable fuels, which has generated growing interest in the use of waste-derived fuels and of biomass fuels. However, from the chemical point of view, biomass is an inhomogeneous fuel, usually with a high concentration of water and considerable amounts of potassium and chlorine, all of which are known to affect the durability of superheater tubes. To slow down or reduce corrosion, power plants using biomass as fuel have been forced to operate at lower steam temperatures as compared to fossil fuel power plants. This reduces power production efficiency: every 10°C rise in the steam temperature results in an approximate increase of 2% in power production efficiency. More efficient ways to prevent corrosion are needed so that power plants using biomass and waste-derived fuels can operate at higher steam temperatures. The aim of this work was to shed more light on the alkali-induced corrosion of superheater steels at elevated temperatures, focusing on potassium chloride, the alkali salt most frequently encountered in biomass combustion, and on potassium carbonate, another potassium salt occasionally found in fly ash. The mechanisms of the reactions between various corrosive compounds and steels were investigated. Based on the results, the potassium-induced accelerated oxidation of chromia protected steels appears to occur in two consecutive stages. In the first, the protective chromium oxide layer is destroyed through a reaction with potassium leading to the formation of intermediates such as potassium chromate (K2CrO4) and depleting the chromium in the protective oxide layer. As the chromium is depleted, chromium from the bulk steel diffuses into the oxide layer to replenish it. In this stage, the ability of the material to withstand corrosion depends on the chromium content (which affects how long it takes the chromium in the oxide layer to be depleted) and on external factors such as temperature (which affects how fast the chromium diffuses into the protective oxide from the bulk steel). For accelerated oxidation to continue, the presence of chloride appears to be essential.

Growth and nutrient concentration in coffee root system under weed species competition

The effects of competition of six weed species on growth, nutrient concentration and nutrient content of coffee plant root system under greenhouse conditions were evaluated. Thirty days after coffee seedling transplantation into 12 L pots with soil level area of 6.5 dm². Weeds were transplanted or sowed in these pots, at densities of 0, 1, 2, 3, 4 and 5 plants per pot. The duration of competition (or weedy periods) from weed transplantation or emergence until plant harvesting, at the weed preflowering stage, were (in days): 77 (Bidens pilosa), 180 (Commelina diffusa), 82 (Leonurus sibiricus), 68 (Nicandra physaloides), 148 (Richardia brasiliensis) and 133 (Sida rhombifolia). Dry matter of coffee plants was linearly reduced with increasing B. pilosa and S. rhombifolia density, with pronounced effect of B. pilosa. C. diffusa was the only weed species whose increasing density in the pots did not diminish crop root dry matter. L. sibiricus, N. physaloides and R. brasiliensis reduced root dry matter of coffee plants by 75, 52 and 47%, respectively, as compared to the weed-free treatment, regardless of weed density. Under competition, even though weed species showed lower macronutrient concentration in the roots (except for P), they accumulated 4.2 (N), 12.3 (P), 4.3 (K), 5.5 (Ca), 7.6 (Mg) and 4.4 (S) times more nutrients in the roots than the coffee plants. Crop and weed nutrient concentration, as well as competition degrees greatly varied depending on both weed species and densities.

Crystallization of selected anions and cations from mine waters

The aim of this Master’s thesis was to review some methods that are already being utilized in a field of mine water purification and to find and study possible new methods and chemicals for mine water purification by precipitation. The target was also to list the optimal process conditions for these precipitating chemicals. Separation methods were reviewed for several anions and cations, but being a real topical issue, sulphate removal was selected to be in the main focus. Sulphate salts e.g. Na2SO4 are relatively soluble in water, which makes the separation processes difficult. Eutectic freeze crystallization was studied more closely in laboratory tests for sodium sulphate removal. Gravimetric solubility tests were made for three cases of mixed electrolyte solutions: Na2SO4 – NaOH, BaSO4 – NaOH and Na3PO4 – NaOH. The aim of these experiments was to study the effect of NaOH addition on solubility of the studied salt. These phenomena were however noticed to be difficult to see in the used laboratory tests. Thus mathematical modelling was utilized to contribute the laboratory experiments and to bring additional information of the influence of NaOH presence on solubility of selected electrolytes, Na2SO4 and Na3PO4. The results from mathematical modelling of activity coefficients suggest Na2SO4 and Na3PO4 to be precipitated rather with presence and with higher concentrations of NaOH, since the raise of NaOH concentration decreases the solubility of these electrolytes in water.

Reverse osmosis membrane surface modification: effects on membrane performance

The aim of this thesis was to study the surface modification of reverse osmosis membranes by surfactants and the effect of modification on rejection and flux. The surfactants included anionic and nonionic surfactants. The purpose of membrane modification was to improve pure water permeability with increasing salt rejection. The literature part of the study deals with the basic principles of reverse osmosis technology and factors affecting the membrane performance. Also the membrane surface modification by surfactants and their influence on membrane’s surface properties and efficiency (permeability and salt rejection) were discussed. In the experimental part of the thesis two thin-film composite membranes, Desal AG and LE-4040, were modified on-line with three different surfactants. The effects of process parameters (pressure, pH, and surfactant concentration) on surface modification were also examined. The characteristics of the modified membranes were determined by measuring the membranes’ contact angle and zeta potentials. The zeta potential and contact angle measurements indicate that the surfactants were adsorbed onto the both membranes. However, the adsorption did not effect on membrane’s pure water permeability and salt rejection. Thereby, the surface modification of the Desal AG and LE-4040 membranes by surfactants was not able to improve the membrane’s performance.

On-line determination of residual collector concentration in flotation process

Valuable minerals can be recovered by using froth flotation. This is a widely used separation technique in mineral processing. In a flotation cell hydrophobic particles attach on air bubbles dispersed in the slurry and rise on the top of the cell. Valuable particles are made hydrophobic by adding collector chemicals in the slurry. With the help of a frother reagent a stable froth forms on the top of the cell and the froth with valuable minerals, i.e. the concentrate, can be removed for further processing. Normally the collector is dosed on the basis of the feed rate of the flotation circuit and the head grade of the valuable metal. However, also the mineral composition of the ore affects the consumption of the collector, i.e. how much is adsorbed on the mineral surfaces. Therefore it is worth monitoring the residual collector concentration in the flotation tailings. Excess usage of collector causes unnecessary costs and may even disturb the process. In the literature part of the Master’s thesis the basics of flotation process and collector chemicals are introduced. Capillary electrophoresis (CE), an analytical technique suitable for detecting collector chemicals, is also reviewed. In the experimental part of the thesis the development of an on-line CE method for monitoring the concentration of collector chemicals in a flotation process and the results of a measurement campaign are presented. It was possible to determine the quality and quantity of collector chemicals in nickel flotation tailings at a concentrator plant with the developed on-line CE method. Sodium ethyl xanthate and sodium isopropyl xanthate residuals were found in the tailings and slight correlation between the measured concentrations and the dosage amounts could be seen.

Effect of desiccation and salinity stress on seed germination and initial plant growth of Cucumis melo

Smellmelon, an annual invasive weed of soybean production fields in the north of Iran, reproduces and spreads predominately through seed production. This makes seed bank survival and successful germination essential steps in the invasive process. To evaluate the potential of Smellmelon to invade water-stressed environments, laboratory studies were conducted to investigate the effect of desiccation and salinity at different temperatures on seed germination and seedling growth of Cucumis melo. Seeds were incubated at 25, 30, 35 and 40 ºC in the darkness in a solution (0, -0.2, -0.4, -0.6, -0.8, 1 and 1.2 MPa) of a salt (NaCl), and in a solution (0, -2, -4, -6, -8, -10, -12 bar) of PEG-6000 (Polyethylene glycol), in two separate experiments. The results showed that the highest percentage and rate of germination occurred at 35 ºC in salt concentrations of 0, -0.2, -0.4 MPa and PEG concentrations of 0, -2, -4 bar. Increasing the concentration of salt (NaCl) and PEG limited germination, seedling growth and water uptake but increased the sodium content in the seedlings. No significant difference was observed among 0, -0.2 and -0.4 MPa of NaCl and among 0, -2 and -4 bar of PEG concentration at 35 ºC. The negative effects of PEG were more than those of NaCl on germination percentage and germination rate. Increased stress levels lead to reduction of root and shoot length, and SVL of seedlings. Na+ content of seedling decreased with limited seedling growth of C. melo.

Germination ecology of wild onion: a rainfed crop weed

Asphodelus tenuifolius is becoming a more common weed in rain-fed area in Pakistan. Laboratory and greenhouse experiments were conducted to determine the effect of different environmental factors on germination and emergence of A.tenuifolius. Results showed that A.tenuifolius can tolerate a wide range of varying environmental factors. Greatest percentage of germination (80%) was recorded at 15 ºC constant temperature; however, considerable germination occurred at 20 and 25 ºC. Light for 10 h photoperiod stimulate germination of Asphodelus tenuifolius compared with complete darkness. Germination was totally inhibited at osmotic stress higher than -0.8 MPa. There was no significant difference in germination at pH 6 to 8; however, there was a slightly decrease at pH 9, compared with distilled water. Asphodelus tenuifolius was very sensitive to salinity; however, a few seeds of A.tenuifolius were able to germinate even at 150 mM NaCl concentration. Greatest emergence occurred with seed placed at soil surface and emergence decreased with increase in burial depth. No emergence occurred from 4 cm or greater. This information may aid in developing tools and strategies for management.

Respuestas morfológicas y anatómicas de Tessaria absinthioides (Hook. et Arn.) DC. a la salinidad

T. absinthioides, Inuleae, Compositae, is a weedy species that is spreading in the irrigation area of the Colorado River, Argentina. This species can be found in normal and saline soils. Morphological and anatomical variables were measured with two salts, sodium chloride and sodium sulfate, with three levels of osmotic potential -0.4, -0.8 and -1.5 MPa, in hydroponic culture, using Hoagland solution as the cultivation media. The total diameter of the roots of plants growing in Na2SO4 and NaCl increased when the osmotic potential was -0.4 MPa. In plants growing in NaCl this may have resulted from the increase in the size of the cortical cells and in plants growing in Na2SO4, the diameter increased may be due to an increase in the cambial activity. The number and length of shoot internodes decreased with increasing salinity, even though this was not statistically significant. In comparison to the control, the total diameter of the shoot increased at -0.4 MPa and decreased with the reduction of the osmotic potential. In comparison to the control, the length of the leaves decreased at -0.4 MPa and the leaves width increased at the same concentration. The palisade parenchyma appeared less developed in saline conditions. In comparison to the control, the number of hairs increased at -0.4 MPa. T. absinthioides acts as a semihalophytic species, according to the salt ranks it tolerates. The mechanisms of adaptation to saline conditions are succulence in root and stunted growth if the salt in the media is NaCl, and the production of haloxeromorphic characters if the salt in the media is Na2 SO4

Effect of nitrate and ammonium on the growth and protein concentration of Microcystis viridis Lemmermann (Cyanobacteria)

Cyanobacteria are a very important group in aquatic systems, particularly in eutrophic waters. Therefore studies about their success in the environment are essential. Many hypotheses have tried to explain the dominance of Cyanobacteria, and several emphasized the importance of various nitrogen sources for the success of the group. In this study, we measured the effect of ammonium and nitrate on the growth and protein concentration of Microcystis viridis (Cyanobacteria). This species is well-known because bloom formation in eutrophic waters. The study was carried out, in experimental batch cultures, using the WC medium with different nitrogen sources: ammonium, nitrate, ammonium + nitrate (50% ammonium + 50% nitrate) and ammonium at different concentrations (to test for possible NH4+ toxicity). Protein, ammonium and nitrate concentrations were measured at end of each experiment, whereas samples for cell counts were taken daily. Results showed that Microcystis viridis grew faster with ammonium (µ = 0.393 day-1) than with nitrate (µ = 0.263 day-1) and ammonium + nitrate (µ = 0.325 day-1). This pattern is explained by the metabolism of ammonium that presents higher uptake and assimilation rates than nitrate. Maximum cell concentration, however, was higher in the ammonium + nitrate treatment, followed by nitrate treatment. Higher protein concentration were observed in the treatment with nitrate. In the ammonium toxicity test, no difference between the control and NH4+ at 50% was found. Thus, the ammonium concentrations used in these experiments were not toxic. Our results suggest that Cyanobacteria is able to grow on both nitrogen sources even if ammonium may allow faster growth and bloom development.

Utilization of steelmaking waste materials for production of calcium carbonate (CaCO3)

The steel industry produces, besides steel, also solid mineral by-products or slags, while it emits large quantities of carbon dioxide (CO2). Slags consist of various silicates and oxides which are formed in chemical reactions between the iron ore and the fluxing agents during the high temperature processing at the steel plant. Currently, these materials are recycled in the ironmaking processes, used as aggregates in construction, or landfilled as waste. The utilization rate of the steel slags can be increased by selectively extracting components from the mineral matrix. As an example, aqueous solutions of ammonium salts such as ammonium acetate, chloride and nitrate extract calcium quite selectively already at ambient temperature and pressure conditions. After the residual solids have been separated from the solution, calcium carbonate can be precipitated by feeding a CO2 flow through the solution. Precipitated calcium carbonate (PCC) is used in different applications as a filler material. Its largest consumer is the papermaking industry, which utilizes PCC because it enhances the optical properties of paper at a relatively low cost. Traditionally, PCC is manufactured from limestone, which is first calcined to calcium oxide, then slaked with water to calcium hydroxide and finally carbonated to PCC. This process emits large amounts of CO2, mainly because of the energy-intensive calcination step. This thesis presents research work on the scale-up of the above-mentioned ammonium salt based calcium extraction and carbonation method, named Slag2PCC. Extending the scope of the earlier studies, it is now shown that the parameters which mainly affect the calcium utilization efficiency are the solid-to-liquid ratio of steel slag and the ammonium salt solvent solution during extraction, the mean diameter of the slag particles, and the slag composition, especially the fractions of total calcium, silicon, vanadium and iron as well as the fraction of free calcium oxide. Regarding extraction kinetics, slag particle size, solid-to-liquid ratio and molar concentration of the solvent solution have the largest effect on the reaction rate. Solvent solution concentrations above 1 mol/L NH4Cl cause leaching of other elements besides calcium. Some of these such as iron and manganese result in solution coloring, which can be disadvantageous for the quality of the PCC product. Based on chemical composition analysis of the produced PCC samples, however, the product quality is mainly similar as in commercial products. Increasing the novelty of the work, other important parameters related to assessment of the PCC quality, such as particle size distribution and crystal morphology are studied as well. As in traditional PCC precipitation process, the ratio of calcium and carbonate ions controls the particle shape; a higher value for [Ca2+]/[CO32-] prefers precipitation of calcite polymorph, while vaterite forms when carbon species are present in excess. The third main polymorph, aragonite, is only formed at elevated temperatures, above 40-50 °C. In general, longer precipitation times cause transformation of vaterite to calcite or aragonite, but also result in particle agglomeration. The chemical equilibrium of ammonium and calcium ions and dissolved ammonia controlling the solution pH affects the particle sizes, too. Initial pH of 12-13 during the carbonation favors nonagglomerated particles with a diameter of 1 μm and smaller, while pH values of 9-10 generate more agglomerates of 10-20 μm. As a part of the research work, these findings are implemented in demonstrationscale experimental process setups. For the first time, the Slag2PCC technology is tested in scale of ~70 liters instead of laboratory scale only. Additionally, design of a setup of several hundreds of liters is discussed. For these purposes various process units such as inclined settlers and filters for solids separation, pumps and stirrers for material transfer and mixing as well as gas feeding equipment are dimensioned and developed. Overall emissions reduction of the current industrial processes and good product quality as the main targets, based on the performed partial life cycle assessment (LCA), it is most beneficial to utilize low concentration ammonium salt solutions for the Slag2PCC process. In this manner the post-treatment of the products does not require extensive use of washing and drying equipment, otherwise increasing the CO2 emissions of the process. The low solvent concentration Slag2PCC process causes negative CO2 emissions; thus, it can be seen as a carbon capture and utilization (CCU) method, which actually reduces the anthropogenic CO2 emissions compared to the alternative of not using the technology. Even if the amount of steel slag is too small for any substantial mitigation of global warming, the process can have both financial and environmental significance for individual steel manufacturers as a means to reduce the amounts of emitted CO2 and landfilled steel slag. Alternatively, it is possible to introduce the carbon dioxide directly into the mixture of steel slag and ammonium salt solution. The process would generate a 60-75% pure calcium carbonate mixture, the remaining 25-40% consisting of the residual steel slag. This calcium-rich material could be re-used in ironmaking as a fluxing agent instead of natural limestone. Even though this process option would require less process equipment compared to the Slag2PCC process, it still needs further studies regarding the practical usefulness of the products. Nevertheless, compared to several other CO2 emission reduction methods studied around the world, the within this thesis developed and studied processes have the advantage of existing markets for the produced materials, thus giving also a financial incentive for applying the technology in practice.