泥生绿菌的分离鉴定及其在净化废水中作用的初步探讨

本文介绍了从厌氧间歇膨胀光合反应器内的活性污泥中分离并鉴定的泥生绿菌(Chlorobium limicola Nadson)S1,它属严格厌氧光能自养型细菌，在有硫化物和少量碳酸氢盐存在下，有广泛利用有机物的能力，它的最适生长温度为28-30℃,最适生长PH为6.5-7.0，且含有氢化酶。因此，它能与甲烷发酵菌共存而共同作用，达到废水净化之目的。通过光照(2#反应器)和黑暗(1#反应器)对比实验，表明了在光照条件下即有泥生绿菌S1存在下，反应系统能更好地降低CODcr、BOD5 和提高CH4 含量，在四个负荷段的运行中，2#反应器在后三个负荷段的甲烷含量能稳定在91.6%而1#反应器为87%，2#反应器的二氧化碳含量为4.5%而1#反应器为8.8%，于28.35g/l.d的负荷下，2#反应器CODcr去除率达83.4%，BOD去除率达74.53%，分别较1#反应器高10.8%,6.4%。COD去除率提高了14%，BOD去除率提高了9.3%。本试验的试验条件为：白天自然光照，晚上电源光照，光照强度为1000-2500lux，通过连续动态运转，并以恒定的流速将废液注入反应器中，进水PH控制在6.5-7.2，反应器厌氧，恒温室温度控制在30±1℃。为使整个试验中同一水质条件下进行，进水采用化学合成培养基。This paper reports a Chlorobium Liwicola S1's isolation and identification. It is a strictly anaerobic and photosynthetic autotrophic bacterium. Along with sulfidedepondent CO2 assiwilaton,a few simple organic compounds can be photoassimilated. Acetate is most effectively used. Its best conditons of growth are 28-30℃,PH 6.5-7.0, and it contains hydrogenase. So it can live with methanefermentative bacteria in order to treat wastewater. At the same time, the treatment of wastwater using Chlorobium Limicola S1 with methane-fermontative bacteria under dark anaerobic and light anaerobic conditions is studied. In contrast with 1# reactor-darken, 2# reactor-illuminated can lossen wastewater's CODcr, BOD5 and on hance CH4 content better. In the test, 2# reactor's CH4 content is stable at 91.6%, but 1# reactor's is 87%. The CO2 content of 2# reactor is 4.5%, but 1# reactor's is 8.8%. When the load of teatment is 28.35g/l.d, the COD removal effficiency is 83.4% and the BOD removal efficiency is 74.53% in 2# reactor. They are separately 10.8%, 6.4% higher than 1# reactor's.

碱法草浆造纸蒸煮黑液厌氧生物降解性及其主要微生物类群研究

造纸行业是造成我国水环境有机污染物的重要污染源之一，其水污染的特点是小厂多、草浆多、工艺落后、污染扩散面广、造成废 水排放量大，每年排放的废水量约39亿立方米，占全国工业废水排放量的1/6，其中有机污染物（以BOD5计）160万吨左右，约占全 国工业废水中有机污染物总量的1/4。尤以占全国制浆造纸行业90%以上的碱法草浆造纸厂的蒸煮黑液量大面广，除含有机物外，还 含有木质素、残碱、硫化物、氯化物等污染物，属于PH值高、色度深、难于治理的高浓度有机废水，对水体污染特别严重，各地要 求治理呼声很高，急待研究并尽快找出各种有效的治理途径。对于碱法草浆蒸煮，黑液高浓度废水的治理，有各种方法，根据国内 的研究进展和我们已有试验工作表明，最经济有效，具有实用价值，在生产上可获得成功是厌氧处理法。近10多年来，国外关于高 效厌氧处理技术研究进展迅速，并出现了多种多样的工艺设备，如高效厌氧生物反应器，并在实用化方面取得了很大成绩，建立了 生产性装置，达到了高负荷运行，效果良好。本试验是根据我们已有研究基础，针对我国国情，对小型制浆造纸厂水污染防治除了 开发碱回收及各种综合利用技术外，要特别加强废水(废液)实用技术研究的指导思想，本试验采用改进型的上流式厌氧污泥床反应 器，设计了两种试验方案，通过试验结果如下。1. 试验方案I—碱法草浆黑液酸化和厌氧发酵I号UASB反应器动态模型试验结果表 明：(1). 采用中温35℃±1℃高效厌氧反应器USAB内装有填料(陶粒)和三相分离器，具有保持高浓度生物量和防止污泥流失的特点 ，污泥浓度Vs 可达30%以上，因而具有高效、节能、产能、滞留期短的优点，当进水CODcr在7500-10000mg/l，HRT由7天缩短到3天 ，有机容积负荷在1.22gCODcr/l·d-3.43gCODcr/l·d时，CODcr平均去除率可达55%-45.5%，最高CODcr去除率可达60.2-63.5%， BOD5去除率可达75.9-83.2%,沼气容积产气率可达0.29-0.67l/l·d，每克CODcr转化为沼气产率达0.39-0.48l/gCODcr·d，CH4含量 65.8-75.5%。厌氧发酵出水再用化学法进行后处理脱除难降解的木质素，CODcr总去除率达80%以上。(2). 动态试验结果表明：采 用酸化—厌氧发酵处理黑液工艺合理，技术路线可行。2. 试验方案II—黑液用化学法(Hcl)去除木质素进行厌氧发酵，II号UASB反 应器动态模型试验结果表明：(1). 采用中温35℃±1℃高效厌氧反应器UASB(内有软填料)，当进水CODcr7000-13000mg/l左右，HRT 由6天缩短到1天，有机负荷由0.98gCODcr/l·d增加到11gCODcr/l·d时，COD平均去除率均可稳定在70-77%，BOD5去除率为87.3- 93.1%，沼气容积产气率0.21-2.6l/l·d，每克CODcr转化为沼气产率为0.39-0.48l/gCODcr·d，高的可达0.53l/gCODcr·d，转化 率较高，CH4含量63-70%。(2). 试验证明碱法草浆黑液物化预处理—厌氧发酵处理的技术路线也是可行的，工艺合理、效果较好。 在有条件的工厂可采用。3.厌氧发酵阶段几大类群微生物计数表明：(1). 当发酵工艺和运行处于相对稳定状态时，微生物群体的 组成也达到相对的稳定，各类微生物之间保持动态平衡关系。当产乙酸菌的数量为107-108个/ml时，产甲烷菌的数量为105-106 个/ml，当产乙酸菌数量为106-107个/ml时，产甲烷菌的数量为103-105个/ml。(2).稳态运行条件下，黑液预处理为甲烷发酵创造 了有利的生态环境，获得了较好的处理效果和较高的COD转化为沼气的产率0.39-0.48l/g·CODcr·d，反应器中形成较为稳定而数 量较下水污泥中高1-2个数量级的厌氧发酵微生物区系组成。这一结果为黑液厌氧发酵提供了微生物理论依据。Paper industry is one of the important pollution source of water environment in our country. Its character of water pollution is many small factories, much grass pulp, disadvantageous technique, large preading area of pullution. Its effluent makes up 1/6 of whole country's industry wastwater. Its organic pollutant accounts 1/4 of whole country's. Alkaline grass paper pulp effluent with pollutants such as ligoin, remaining alkali sulfide, chloride besides organic material, is a kind of high concentrate organic wastewater which has high PH walug, dark colour and is difficult in treatment. There is urgent require to find ways to treat the wastewater. There are different ways to treat alkaline paper grass pulp effluent. According to the research advances and our experiment work, the most economical and useful way is anaerobic degradation which was advanced quick in last ten years. In the control of waste water of small pulp paper mill, the study of wastewater utilization technology should be emphasized, besides alkaline retrieving and different kinds of comprehensive utilization technology. Our experiment used modified UASB(Upflow Anaerobic Sludge Blanket Reactor). Two kinds of plan were disgned. The results are lined below. 1. The first experiment plant-aciding black pulp effluent and methanogenic digestion. The dynamic model experiment results of I-UASB reactor showed: (1)The mesophilic(35℃±1℃)high effect UASB reactor having haydite and threee state seperation in it had the character of keeping high bioimass concentration and preventing losss of sludge. It had advantages of high effect, energe saving, energe prodcing and short HRT(Hydroulic retention time). When the influent COD was 7500-10000mg, HRT was shortened from 7 days to 3days, organic loading rate was 1.22g-3.43COD/l· d, the average COD removal efficiency was 55%-45%. The highest COD efficiency was 60.2-63.5%, BOD removal of 75.9 -83.4% was achieved. Biogass production rate were up to 0.29-0.67l/l·d. Biogass converted efficiency from every gram of COD could reach 0.39-0.48l/gCOD·d. Methane content was 65.0-75.5%. Chemical method was used to deplate lignin in anaerobic digestion effluent. Total COD removal efficiency could be more than 80%. (2)Using aciding annaerobic digestion to treat the black effluent was reseanable in technique and technology. 2. The second experiment plan-anaerobic digestion was used after the chemical method was used to deplate lignin in the black effluent. The result of dynamic experiment of II-UASB reactor showed: (1)High effect mesophilic (35℃±1℃)UASB reactor having soft slaffing in was used. When influent COD was about 7000-13000mg/l, HRT was shortened from 6 days to 1 day and organic loading rate was increased from 0.90 to 11g COD /l·d, average COD removal efficiency remained stable on 70-77%. BOD, removal efficiency was between 87.3-93.1%. Biogass production rate was 0.2-2.6l/l ·d .Biogass converted efficiency from a gram of COD was 0.39-0.481/gCOD·d with the high value of 0.53l/gCOD·d. Methane content was 63-70%. (2)The way that using physical, chemical Pre-treatment-anaerobic digestion to treat alkaline black effluent is feasible and can be used in some factories when the condition exists. 3. Counting of several class of microoganisms in anaerobic digestion stage showed: (1)As the disgestion was in stable motion, the compositon of microorganic colony could get relative stable. Dynamic balance was remaining among different kinds of microorganism such as methanogenic bacteria, Acidogenic bacteria, sulfate reducing bacteria, and heterotrophic bacteria. (2)Under stable motion, the pre-treatment of black effluent produced favourable eco-enviroment for methanegenic digestion. Good treatment effect and high biogass convertent efficiency from COD(0.39-0.48l/g·COD· d)were gotten. Some stable and high quantity(10-100times more than sewage sludge)microorganism colony were formed in the reactor. This result provided theoretical basis for anaerobic digestion of black effluent.

猪场废水短程硝化反硝化-厌氧氨氧化脱氮研究

畜禽废水是农村水环境污染的主要来源之一，其处理的难点在于脱氮。传统生物脱氮法具有能耗高、需大量外加碳源等缺点，开发低成本、高效率的新型生物脱氮技术具有重要意义。 本研究将短程硝化反硝化和厌氧氨氧化两种脱氮新技术结合，让前者为后者创造去除可降解COD、降低总氮负荷、调整pH、调整氨氮和亚硝酸盐氮浓度比例等进水条件，而后者可在无需外加碳源的条件下进一步脱氮，二者结合可成为高氨氮、低C/N废水脱氮的新途径。 试验以低碳氮比猪场废水为研究对象，首先进行了短程硝化反硝化预处理研究，同时启动并运行调控厌氧氨氧化反应器，最后以经过短程硝化反硝化预处理的猪场废水为进水，进行厌氧氨氧化脱氮考察。实验表明：（1）短程硝化反硝化作为厌氧氨氧化的预处理工序是可行的。猪场废水通过短程硝化反硝化，可以达到基本去除可生化COD、部分脱氮、控制出水氨氮和亚硝酸盐氮浓度之比在1︰1左右、pH在7.5～8.0的目的， COD和总氮平均去除率分别为64.3%、49.1%,出水可达到厌氧氨氧化反应的进水要求。（2）采用模拟废水启动厌氧氨氧化反应器，经过5个月左右的运行调控，反应器启动成功并稳定运行，最高总氮去除率为87.1%，总氮容积去除率最高达到0.14kg/m3.d；整个稳定阶段，氨氮、亚硝酸盐氮、硝酸盐氮的变化量之比为1︰1.21︰0.33。（3）经过短程硝化反硝化预处理的猪场废水厌氧氨氧化脱氮效果稳定，氨氮、亚硝酸盐氮、总氮、COD的平均去除率分别为93.0%、99.4%、84.6%、18.1%，处理效果与模拟废水处理系统相比无明显变化。（4）经过短程硝化反硝化预处理后，猪场废水中残留有机物成分在厌氧氨氧化反应过程中无显著变化，主要为酯类和烷烃类物质；残留有机物对厌氧氨氧化效果无明显影响。（5）采用PCR技术进行特殊功能菌种检测，结果表明模拟废水处理系统和猪场废水处理系统的菌群中均含有厌氧氨氧化菌和好氧硝化菌；通过blast比对，厌氧氨氧化菌扩增序列与未培养的Planctomycetales菌和Candidatus Brocadia fulgida菌16S rRNA部分序列相似性分别为95％、90%。（6）MPN法菌种计数结果显示，模拟废水处理系统和猪场废水处理系统的菌群中均含有硝化细菌、亚硝化细菌和少量反硝化菌，实验条件下的微生物系统是一个厌氧氨氧化菌与好氧硝化菌、反硝化菌共存的系统。 Poultry wastewater is one of the main source of water pollution in rural areas，and nitrogen removal is the most difficult part in treating poultry wastewater. There are some disadvantages in traditional nitrogen removal, such as high energy consumption and more additional organic carbon. It is important to develop ecolomical and efficient technologyies. Shortcut nitricfication/denitrification, as a pretreatment process, was combined with Anammox in this research, so that part of total nitrogen and most degradable COD could be removed by the former, and further nitrogen removal could be implemented by the latter. The combination of the two technologies was a new approach to treat wastewater with high ammonium and low C/N. Piggery wastewater with low C/N was treated in lab-scale experiment. Firstly, shortcut nitrification/denitrification was investigated, and Anammox reactor was started up successfully at the same time. Then piggery wastewater after pretreatment was treated by Anammox. The results showed :(1) It was feasible to take nitrification/denitrification as the pretreatment process of Anammox. By using this process, part of total nitrogen and COD were removed, the ratio of ammonium and nitrite reached around 1︰1 and the pH was about 7.8, which were favorable for Anammox. The average removal percentage of COD and total nitrogen were about 64.3% and 49.1%, respectively. (2) Simulated wastewater was used to start up Anammox reactor. The reactor was started up successfully within 5 months and stable performance was achieved. The highest nitrogen removal reached 87.1% and the biggest volumetric total nitrogen removal rate reached 0.14kg/m3.d. The average ratio of ammonium, nitrite and nitrate was 1:1.21:0.33. (3)Taking the effluent of shortcut nitrification/denitrification as the influent, the nitrogen removal efficiency of Anammox was stable, and the the average removal percentage of ammonium, nitrite, total nitrogen and COD were 93.0%, 99.4% , 84.6% and 18.1%, respectively, which had little difference with that by using simulated wastewater..(4) After pretreatment, the residual organic carbon in piggery wastewater showed no obvious change during the Anammox process, and the main organic compounds were saturated hydrocarbon and ester, which had no obvious negative effect on Anammox process.(5) By PCR technology, the existence of Anammox bacteria was confirmed and the aerobic nitrifying bacteria was found to coexist as well. The result of blast showed that the identities of Anammox bacterium to part of 16S rRNA sequence of uncultured Planctomycetales bacterium and Candidatus Brocadia fulgida bacterium were 95% and 90%, respectively.（6）By MPN method, nitrite oxidizer, ammonium oxidizer and denitrification bacteria were detected in both simulated and piggery wastewater treatment system of Anammox, and the microorganism system was composed of Anammox bacteria，aerobic bacteria and denitrification bacteria together.

Production of Superheavy Nuclei in Massive fusion reactions

A master equation is constructed to treat the nucleon transfer process in heavy ion fusion reactions to form superheavy nucleus. The relative motion concerning the energy, the angular momentum and the fragment deformation relaxations is explicitly treated to couple with the diffusion process. The nucleon transition probabilities, which are derived microscopically, are thus time dependent. The calculated evaporation residue cross-sections for both cold and hot fusion are in good agreement with the known experimental data.

Melatonin in Chinese medicinal herbs

Melatonin is a highly conserved molecule that not only exists in animals, but also is present in bacteria, unicellular organisms and in plants. Since melatonin is an antioxidant, in plants melatonin was speculated to protect them from intrinsic and environmental oxidative stress. More importantly, melatonin in edible plants inevitably enters animals and human through feed and food. In this study, more than 100 Chinese medicinal herbs were analyzed using the methods of solid phase extraction and HPLC-FD on-line with MS to determine whether melatonin is present in these commonly used herbs. Melatonin was detected in majority of these plants. Sixty-four of them contain melatonin in excess of 10 ng per gram dry mass. Melatonin levels in several herbs are in excess of 1000 ng/g. It is well known that normal average physiological plasma levels of melatonin are only 10-60 pg/mL. These high level-melatonin containing plants are traditionally used to treat diseases which presumably involve free radical damage. The current study provides new information concerning one potentially effective constituent present in a large number of medicinal herbs. The results suggest that these herbs should be reevaluated in reference to their nutritional and medicinal value. (C) 2003 Elsevier Science Inc. All rights reserved.

Natural Anthraquinone Derivatives from a Marine Mangrove Plant-Derived Endophytic Fungus Eurotium rubrum: Structural Elucidation and DPPH Radical Scavenging Activity

There is considerable interest in the isolation of potent radical scavenging compounds from natural resources to treat diseases involving oxidative stress. In this report, four new fungal metabolites including one new bisdihydroanthracenone derivative (1, eurorubrin), two new seco-anthraquinone derivatives [3, 2-O-methyl-9-dehydroxyeurotinone and 4, 2-O-methyl4-O-(alpha-D-ribofuranosyl)-9-dehydroxyeurotinone], and one new anthraquinone glycoside [6,3-O-(alpha-D-ribofuranosyl)questin], were isolated and identified from Eurotium rubrum, an endophytic fungal strain that was isolated from the inner tissue of the stem of the marine mangrove plant Hibiscus tiliaceus. In addition, three known compounds including asperflavin (2), 2-O-methyleurotinone (5), and questin (7) were also isolated and identified. Their structures were elucidated on the basis of spectroscopic analysis. All of the isolated compounds were evaluated for 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical scavenging activity.

藻体对水环境中N、P及重金属Cu2+、Pb2+、Cd2+、Cr6+的吸附特征研究

随着全球生态环境的恶化，各国日益重视对水体中各种污染物的治理。利用藻类的吸收、富集和降解作用，可以去除污水中的营养物质、重金属离子和有机污染物，与其他物理、化学及工程的方法相比，该技术具有以下优点：成本低、能耗小、治理效果较好，对环境污染小，有利于资源化，有利于整体生态环境的改善，是治理水质污染的新途径。 本文利用几种大型海藻对富营养化海水进行处理，结果发现孔石莼、刚毛藻均有很强的吸收N、P的能力，吸收能力依次为褶曲刚毛藻>束生刚毛藻>孔石莼。水体中褶曲刚毛藻3 g/L含量，在3～5小时之内，可把中等以上富营养化海水中的N、P降低至一类海水水平。利用刚毛藻处理富营养化地下海水和养殖废水，进行海参和大菱鲆养殖试验，探索藻类净化水质和废水循环利用的新模式，使水体保持较低的营养盐状态，减轻养殖废水对环境的影响，实现了海水养殖业与环境的可持续发展。 刚毛藻在我国近海滩涂分布广泛，利用它来处理富营养化水体，并和水产养殖业相结合，既净化水体，使养殖废水能循环利用，满足水产养殖的需求，又改善水产业生态环境。同时，将回收藻体生产优质饲料、食品和药物等，实现藻类资源的高值利用。刚毛藻营养丰富，用其替代鼠尾藻作海参饲料，资源丰富，成本低，效果好，是一种值得加以开发利用的宝贵资源，具有广泛的应用前景。 生物吸附法是一种经济有效的移除废水中有害重金属离子的方法。由于藻类细胞壁中的多聚糖可提供吸附重金属的位点，廉价而蕴藏丰富的海藻对多种重金属表现出很强的吸附能力。所以本文通过分批实验，研究了非活体刚毛藻对水体中重金属Cu2+、Pb2+和Cd2+的吸附影响因子、吸附热力学、吸附动力学及吸附机理，得到了平衡等温线及动力学数据。吸附过程的最佳pH值为5.0，吸附量随温度的升高而增加，水体中常见的Na+、K+、Ca2+、Mg2+阳离子及Cl-、NO3-、SO42-、C2O42-等阴离子的存在对吸附的影响并不显著。EDTA存在时，吸附百分率大大降低。吸附等温线符合Langmuir和Freundlich方程。刚毛藻对重金属Cu2+、Pb2+和Cd2+的吸附容量很高，25℃时，对Cu2+、Pb2+和Cd2+的最大吸附容量分别为1.61 mmol/g、0.96 mmol/g和0.98 mmol/g，且吸附过程为吸热反应。刚毛藻对重金属Cu2+、Pb2+和Cd2+的吸附过程为化学吸附，在吸附过程中藻体表面的官能团可能与金属离子发生了螯合作用。吸附动力学过程符合pseudo-二级动力学模型，在初始的30min内，吸附速率很快，随后速率逐渐降低。解吸试验表明，用EDTA可以对重金属进行回收，刚毛藻可以循环利用。实验结果表明刚毛藻是一种高效、经济实用的生物吸附材料，可用来吸附回收水体中的重金属Cu2+、Pb2+和Cd2+等。 通过非活体刚毛藻对重金属Cr6+的吸附影响因子、吸附动力学、吸附机理的研究发现，刚毛藻对Cr6+具有很强的还原能力，对电镀废水中的Cr6+的还原去除提供了非常好的方法。吸附过程的最佳pH值为2～3，实际电镀废水通常在此pH范围，因此处理实际废水时，首先在原酸性条件下，对Cr6+进行还原去除，然后调废水pH至5.0，继续进行吸附，去除其他二价离子及被还原的三价Cr离子，实现了利用同一材料还原Cr6+为Cr3+，并将Cr3+和其他重金属离子同时去除。通过对机理的讨论，认为刚毛藻对Cr6+的生物吸附过程不是一个简单的“离子交换过程”，而是一个“吸附还原过程”。在海藻量足够的前提下，只要时间足够长，Cr6+可被彻底还原去除。 利用工业废弃物褐藻渣，对水体中重金属离子Cu2+、Pb2+、Cd2+及Cr6+的生物吸附特性分别进行了讨论，结果表明褐藻渣对重金属离子的吸附特性与刚毛藻一致，吸附等温线符合Langmuir和Freundlich方程，在25℃时，pH为5.0时，由Langmuir方程求出褐藻渣对Cu2+、Pb2+和Cd2+的最大吸附容量分别为4.20 mmol/g、3.13 mmol/g和2.97 mmol/g。褐藻渣对低、高浓度的重金属Cr6+都具有很强的吸附能力，且移除效果比较彻底。实际应用结果表明，褐藻渣是一种高效、经济实用的生物吸附材料，可用来吸附回收水体中的重金属离子，具有广泛的应用前景。

Boundary Element Method (BEM) Analysis for Galvanic Corrosion of Hot Dip Galvanized Steel Immersed in Seawater

A numerical analysis of galvanic corrosion of hot-dip galvanized steel immersed in seawater was presented. The analysis was based on the boundary element methods (BEMs) coupled with Newton-Raphson iterative technique to treat the nonlinear boundary conditions, which were determined by the experimental polarization curves. Results showed that galvanic current density concentrates on the boundary of steel substrate and zinc coating, and the sacrificial protection of zinc coating to steel substrate results in overprotection of steel cathode. Not only oxygen reduction but also hydrogen reduction could occur as cathode reactions, which probably led up to the adsorption and absorption of hydrogen atoms. Flat galvanized steel tensile sample shows a brittle behavior similar to hydrogen embrittlement according to the SSRT (show strain rate test) in seawater.

压力和铁含量对铁方镁石(Mg1-xFex)O(x<=0.25)弹性常数影响的第一性原理研究

By first principle methods based on density functional theory (DFT),the equation of state(EOS) and elastic constants of both periclase and ferropericlase are calculated. The pressure and iron doping effects on the elastic constants of ferropericlase are investigated systematically. Firstly, we calculate the elastic constants of periclase and compare the obtained results with experimental data and other theoretical calculations, which shows a encouraging consistence and demonstrates the practicability of first-principle methods. Secondly, by adding iron into periclase crystal model, we build up ferropericlase with iron contents ranging from 0% to 25% mole percent. The corresponding elastic constants are calculated in a large pressure range(0~120GPa). Emphatically, the strong correlation of 3d electrons in transitional elements, such as iron, is difficult to treat in first-principle methods for a long time. The current solution is to make additional correction. During the initial stage of this study, the strong correlation of 3d electrons in iron is not considered, and we observed that addition of iron decreases the volume of ferropericlase, which is totally contradictory to the experimental data. By applying LDA+U approximation in order to solve the strongly correlated 3d electron of iron, we observed the expansion of volume by iron as expected. On the basis of the LDA+U approximation, the elastic constants of ferropericlase are calculated. After a detailed analysis of data obtained from theoretical calculations, we have reached the following conclusions:(1)pressure imposes positive effects on all elastic constants, and the degree of effects is C11>C12>C44. (2) Iron has no distinctive effects on C11 and C12, although some fluctuations are observed around 60GPa. However, iron has obvious softening effects on C44 The softening effects on C44 are intensified as pressure increases. Above the 100GPa, the effects increase greatly, even surpasses the pressure's positive effects in ferropericlase crystal models with iron mole percent of having 12.5%, 18.75% and 25% iron content. (3)As to the modulus deprived from elastic constants, iron has no effect on the adiabatic bulk module BS, only a little fluctuation around 60GPa. We find iron's softening effects on shear modulus G. (4)We find out that, compared with low iron content, elastic constants with iron content approaching 25mole% is consistently fluctuated，which may be caused by the limitations of the LDA+U approximation method itself. (5)We investigate the pressure and Fe doping effects on elastic anisotropy factor（A=(2C44+C12-C11)/C11） of ferropericlase and find out that iron contents will lower the critical isotropic pressure. At the same pressure, when the pressure is below the isotropic pressure, iron softens the anisotropy factor ; when pressure surpasses the isotropic pressure, iron increases the anisotropy factor.

地理信息系统支持下的滑坡灾害空间分析预测-以云南小江流域为例

As a typical geological and environmental hazard, landslide has been causing more and more property and life losses. However, to predict its accurate occurring time is very difficult or even impossible due to landslide's complex nature. It has been realized that it is not a good solution to spend a lot of money to treat with and prevent landslide. The research trend is to study landslide's spatial distribution and predict its potential hazard zone under certain region and certain conditions. GIS(Geographical Information System) is a power tools for data management, spatial analysis based on reasonable spatial models and visualization. It is new and potential study field to do landslide hazard analysis and prediction based on GIS. This paper systematically studies the theory and methods for GIS based landslide hazard analysis. On the basis of project "Mountainous hazard study-landslide and debris flows" supported by Chinese Academy of Sciences and the former study foundation, this paper carries out model research, application, verification and model result analysis. The occurrence of landslide has its triggering factors. Landslide has its special landform and topographical feature which can be identify from field work and remote sensing image (aerial photo). Historical record of landslide is the key to predict the future behaviors of landslide. These are bases for landslide spatial data base construction. Based on the plenty of literatures reviews, the concept framework of model integration and unit combinations is formed. Two types of model, CF multiple regression model and landslide stability and hydrological distribution coupled model are bought forward. CF multiple regression model comes form statistics and possibility theory based on data. Data itself contains the uncertainty and random nature of landslide hazard, so it can be seen as a good method to study and understand landslide's complex feature and mechanics. CF multiple regression model integrates CF (landslide Certainty Factor) and multiple regression prediction model. CF can easily treat with the problems of data quantifying and combination of heteroecious data types. The combination of CF can assist to determine key landslide triggering factors which are then inputted into multiple regression model. CF regression model can provide better prediction results than traditional model. The process of landslide can be described and modeled by suitable physical and mechanical model. Landslide stability and hydrological distribution coupled model is such a physical deterministic model that can be easily used for landslide hazard analysis and prediction. It couples the general limit equilibrium method and hydrological distribution model based on DEM, and can be used as a effective approach to predict the occurrence of landslide under different precipitation conditions as well as landslide mechanics research. It can not only explain pre-existed landslides, but also predict the potential hazard region with environmental conditions changes. Finally, this paper carries out landslide hazard analysis and prediction in Yunnan Xiaojiang watershed, including landslide hazard sensitivity analysis and regression prediction model based on selected key factors, determining the relationship between landslide occurrence possibility and triggering factors. The result of landslide hazard analysis and prediction by coupled model is discussed in details. On the basis of model verification and validation, the modeling results are showing high accuracy and good applying potential in landslide research.

DAS24-3B数据采集系统控制系统软件的研制与开发

Under the auspices of the 'knowledge-Innovation Program' of CAS, Institute of Geology and Geophysics has established the Broadband Seismic Laboratory. A new kind of 24-bit high-resolution seismograph DAS24-3B has been designed and manufactured in an effort of developing China's own technology of seismic array. Since these instruments will primarily be used in field operation, there is a need to optimize the system software of data acquisition system (DAS) to enhance its stability, compatibility and maintenance. The design ideas of the system software of DAS24-3B are partly learned from the advanced DAS 72A-08. In this system there are two exclusive communication programs DNAPI-COM1 and DNAPI-LPT1, which are suitable for all standard industrial computers with ECP parallel port and serial port. By these exclusive parallel and serial communication interface the system software is split into three parts, acquisition program, user's control program and graphical display program, which can function well in separate units and can run correctly in whole. The three parts of DAS24-3B's system software possess different functions and advantages. The function of acquisition program is to control the process of seismic data acquisition. DAS24-3B system reduced its power and harddisk read-write disturbance by using the extended memory attached to its CPU, which functions as enlarging the data buffer of system and lessening the times of harddisk read-write operations. Since GPS receiver of DAS is strongly sensitive to the around environment and has the possibility of signal loss the acquisition program has been designed with the ability to automatically trail the GPS locked time. The function of user's controlling program is to configure the system's work environment, to inform the user's commands to DAS, to trail the status of DAS in real-time. The function of graphical display program is to illustrate data in figures, to convert data file into some common formatted file, to split data file in parts and combine data files into one. Both user's control program and graphical display program are API (Application Programming Interface) in window 95/98 system. Both possess the features of clearness and friendship by use of all kind of window controls, which are composed by menu, toolbar, statusbar, dialogue box, message box, edit box, scrollbar, time control, button and so on. Two programs of systemic exception handles are provided to treat the trouble in field. The DAS24-3B DAS has been designed to be easier to use-better ability, more stable and simpler. It has been tested in field and base station and has been proved more suitable for field operation of seismic array than other native instruments.

基于工程地质力学的岩土工程加固理论、技术与实践

In the engineering reinforcement of-rock and soil mass, engineers must consider how to obtain better reinforcing effect at the cost of less reinforcing expense, which, in fact, is the aim of reinforcement design. In order to accomplish the purpose, they require not only researching the material used to reinforce and its structure, but also taking into account of several important geological factors, such as the structure and property of rock and soil mass. How to improve the reinforcing effect according to engineering geomechanical principle at the respect of the reinforcement of engineering soil and rock mass is studied and discussed in this paper. The author studies the theory, technology and practice of geotechnical reinforcement based on engineering geomechanics, taking example for the soil treatment of Zhengzhou Airport, the effect analysis of reinforcement to the slope on the left bank of Wuqiangxi Hydropower Station and the reinforcing design of the No. 102 Landslide and unique sand-slide slope on the Sichuan-Tibet Highway. The paper is comprised of two parts for the convenience of discussion. In the first part, from the first chapter to the fifth chapter, trying to perform the relevant research and application at the viewpoint of soil mass engineering geomechanics, the author mainly discusses the study of reinforcing soft ground soil through dynamical consolidation and its application. Then, in the second part, from the sixth chapter to the eleventh chapter, the study of new technologies in the rock slope reinforcement and their application are discussed. The author finds that not only better reinforcing effect can be gained in the research where the principle and method of rock mass engineering geomechanics is adopted, but also new reinforcing technologies can be put forward. Zhengzhou Airport is an important one in central plains. It lies on Yellow River alluvial deposit and the structure of stratum is complex and heterogeneous. The area of airport is very large, which can result in differential settlement easily, damage of airport and aircraft accident, whereas, there are no similar experiences to dispose the foundation, so the foundation treatment become a principal problem. During the process of treatment, the method of dynamic compaction was adopted after compared with other methods using the theory of synthetic integration. Dynamic compaction is an important method to consolidate foundation, which was successfully used in the foundation of Zhengzhou Airport. For fill foundation, controlling the thickness of fill so as to make the foundation treatment can reach the design demand and optimum thickness of the fill is a difficult problem. Considering this problem, the author proposed a calculation method to evaluate the thickness of fill. The method can consider not only the self-settlement of fill but also the settlement of the ground surface under applied load so as to ensure the settlement occurred during the using period can satisfy the design demand. It is proved that the method is correct after using it to choose reasonable energy of dynamic compaction to treat foundation. At the same time, in order to examine the effect of dynamic compaction, many monitor methods were adopted in the test such as static loading test, modulus of resilience test, deep pore pressure -test, static cone penetration test and the variation of the pore volume measurement. Through the tests, the author summarized the discipline of the accumulation and dissipation of pore pressure in Yellow River alluvial deposit under the action of dynamic compaction, gave a correct division of the property change of silt and clay under dynamic compaction, determined the bearing capacity of foundation after treatment and weighted the reinforcing effect of dynamic consolidation from the variation of the soil particle in microcosmic and the parameter of soil mass' density. It can be considered that the compactness of soil is in proportion to the energy of dynamic compaction. This conclusion provided a reference to the research of the "Problem of Soil Structure-the Central Problem of Soil Mechanics in 21 Century ". It is also important to strengthen rock mass for water conservancy and electric power engineering. Slip-resistance pile and anchoring adit full of reinforced concrete are usually adopted in engineering experience to strengthen rock mass and very important for engineering. But there also some deficiency such as the weakest section can't be highlighted, the monitor is inconvenient and the diameter of pile and adit is very large etc. The author and his supervisor professor Yangzhifa invented prestressed slip-resistance pile and prestressed anchoring adit full of reinforced concrete, utilizing the advantage that the prestressed structure has better anti-tensile characteristic (this invention is to be published). These inventions overcome the disadvantages of general slip-resistance pile and anchoring adit full of reinforced concrete and have the functions of engineering prospecting, strengthening, drainage and monitor simultaneous, so they have better strengthened effect and be more convenient for monitor and more economical than traditional methods. Drainage is an important factor in treatments of rock mass and slop. In view of the traditional drainage method that drainage pore often be clogged so as to resulted in incident, professor Yangzhifa invented the method and setting of guide penetration by fiber bundle. It would take good effect to use it in prestressed slip-resistance pile and anchoring adit full of reinforced concrete. In this paper, the author took example for anchoring adit full of reinforced concrete used to strengthen Wuqiangxi left bank to simulate the strengthened effect after consolidated by prestressed slip-resistance pile, took example for 102 landslide occurred along Sichuan-Tibet highway to simulate the application of slip-resistance pile and the new technology of drainage. At the same time the author proposed the treatment method of flowing sand in Sichuan-Tibet highway, which will benefit the study on strengthening similar engineering. There are five novelties in the paper with the author's theoretical study and engineering practice: 1. Summarizing the role of pore water pressure accumulation and dissipation of the Yellow River alluvial and diluvial soil under the action of dynamical consolidation, which has instructive significance in the engineering construction under the analogical engineering geological conditions in the future. It has not been researched by the predecessors. 2. Putting forward the concept of density D in microcosmic based on the microcosmical structure study of the soil sample. Adopting D to weight the reinforcing effect of dynamic consolidation is considered to be appropriate by the means of comparing the D values of Zhengzhou Airport's ground soil before with after dynamically consolidating reinforcement, so a more convenient balancing method can be provided for engineering practice. 3. According to the deep research into the soil mass engineering geology, engineering rock and soil science, soil mechanics, as well as considerable field experiments, improving the consolidating method in airport construction, from the conventional method, which is dynamically compactmg original ground surface firstly, then filling soil and dynamically layer-consolidating or layer-compacting at last to the upgraded method, which is performing dynamical consolidation after filling soil to place totally at the extent of the certain earth-filling depth. The result of the dynamical consolidation not only complies with the specifications, but also reduces the soil treatment investment by 10 million RMB. 4. Proposing the method for calculating the height of the filled soil by the means of estimating the potential displacement produced in the original ground surface and the filled earth soil under the possible load, selecting the appropriate dynamically-compacting power and determining the virtual height of the filled earth soil. The method is proved to be effective and scientific. 5. According to the thought of Engineering Geomechanics Metal-Synthetic Methodology (EGMS), patenting two inventions (to the stage of roclamation, with Professor Yang Zhi-fa, the cooperative tutor, and etc.) in which multi-functions, engineering geological investigation, reinforcement, drainage and strength remedy, are integrated all over in one body at the viewpoint of the breakage mechanism of the rock slope.

污泥处理经济评价和污泥堆肥中氧气监测与动态分析

With the continually increase both in the amount of wastewater disposal and in the treatment rate, more and more sewage sludge has been produced. An economic estimate was taken on the different sewage sludge disposal and treatment technologies, and led to the conclusion that compost is an effective way to make sewage sludge harmless, stable and resourceable. Normally, there are several ways to treat sewage sludge, such as landfill, compost, incineration and so on. These technologies will cost 300-1000 Y per ton of sludge. Among those ways, landfill is the cheapest one and operates easily, however, it just postpones the pollution instead of eventually eliminating the pollution; The amount of the sludge will reduce dramatically after incineration, while incineration will take a very high investment in the beginning, at the same time, it's very hard to maintain running; Sewage sludge will be resourceful after composting treantment, thus makes up the treatment cost, makes composting is the most economical way. Compost production is safe when correctly used, compost is a important way to treat sewage sludge. Oxygen is an important control factor in aerobic composting that has great effects on temperature and microorganisms. The gas gathering and transfering system of an online oxygen monitoring system for composting were bettermented to prolong the monitoring system's running period. The oxygen concentration changes in various aerobic composting stage were studied, and conclusions came to that oxygen concentration changes much faster in the oxygen concentration increasing stage than that in the declining stage; the better the aerobic condition is, the sooner the monitoring system starts to work. The minimal oxygen concentration during a ventilation cycle often falls at the beginning, then ascends in the composting period; at the same time, oxygen concentration changes fast in the early composting stage(temperature increasing stage), much slower in the middle stage(continouns thermophilic stage),and seldom changes in the late composting stage(temperature declining stage). With the help of the oxygen realtime-online monitoring system, oxygen concentrations was measured. During the composting period, water contents was analyzed after sampled. It's found that water contents (WC) and Oxygen concentration can both influence the composting process, and the control rule varies in the various composting stages. Essentially, the rule that water and oxygen control the composting process comes from water counterchecks the oxygen transferring to the composting substrate. The most influential factor to the WC and to the oxygen is the components in the composting pile. In the temperature increasing stage, seldom microorganisms exist in the composting pile with low activity, thus oxygen can meet with microorganisms' need, and WC is the dominant factor. In the high temperature (continouns thermophilic) stage, composting process is controlled by WC and oxygen, essentially by WC, at the same time, their influence somehow is not remarkable. In the temperature declining stage, WC and oxygen influence the composting process little. It's also found that the composting process will differ even if under the same components, thus to equably mix the components can avoid WC focusing in some place and let the composting pile to be aerobic. In one sentence, aerobic state is the most important factor in the composting process, suitable bulking material will be useful to the composting control.

内容预警对说服的影响

There are still some controversies surrounding the effects of forewarning of message content on persuasion and the mediating mechanism operating when persons are forwarned of message content on high involvement. Two experiments were designed to investigate these questionable points. It was found: 1. The effects of a warning on persuasion depends on the extent of involvement. Subjects who were highly involved in the topic showed resistance to persuasion. 2. However, forewarning have different effects on persuasion in the low-involvement condition according to some sub-variables (such as commitment, self -presentation motive, etc.). 3. The mechanism mediating the resistance to persuasion conveyed by a warning concerning the content of an impending discrepand communication on a highly involving topic is very complicated. The experiments indicated that anticipatory counterargument is a typical cognitive response, besides, source degoration and "tubborn refusal to give in" are also usually found.

Specialization of Perceptual Processes

In this report, I discuss the use of vision to support concrete, everyday activity. I will argue that a variety of interesting tasks can be solved using simple and inexpensive vision systems. I will provide a number of working examples in the form of a state-of-the-art mobile robot, Polly, which uses vision to give primitive tours of the seventh floor of the MIT AI Laboratory. By current standards, the robot has a broad behavioral repertoire and is both simple and inexpensive (the complete robot was built for less than $20,000 using commercial board-level components). The approach I will use will be to treat the structure of the agent's activity---its task and environment---as positive resources for the vision system designer. By performing a careful analysis of task and environment, the designer can determine a broad space of mechanisms which can perform the desired activity. My principal thesis is that for a broad range of activities, the space of applicable mechanisms will be broad enough to include a number mechanisms which are simple and economical. The simplest mechanisms that solve a given problem will typically be quite specialized to that problem. One thus worries that building simple vision systems will be require a great deal of {it ad-hoc} engineering that cannot be transferred to other problems. My second thesis is that specialized systems can be analyzed and understood in a principled manner, one that allows general lessons to be extracted from specialized systems. I will present a general approach to analyzing specialization through the use of transformations that provably improve performance. By demonstrating a sequence of transformations that derive a specialized system from a more general one, we can summarize the specialization of the former in a compact form that makes explicit the additional assumptions that it makes about its environment. The summary can be used to predict the performance of the system in novel environments. Individual transformations can be recycled in the design of future systems.