On response time reduction of electrothermomechanical MEMS using topology optimization

Electrothermomechanical MEMS are essentially microactuators that operate based on the thermoelastic effect induced by the Joule heating of the structure. They can be easily fabricated and require relatively low excitation voltages. However, the actuation time of an electrothermomechanical microdevice is higher than the actuation times related to electrostatic and piezoelectric actuation principles. Thus, in this research, we propose an optimization framework based on the topology optimization method applied to transient problems, to design electrothermomechanical microactuators for response time reduction. The objective is to maximize the integral of the output displacement of the actuator, which is a function of time. The finite element equations that govern the time response of the actuators are provided. Furthermore, the Solid Isotropic Material with Penalization model and Sequential Linear Programming are employed. Finally, a smoothing filter is implemented to control the solution. Results aiming at two distinct applications suggest the proposed approach can provide more than 50% faster actuators. (C) 2012 Elsevier B.V. All rights reserved.

Genotoxicity assessment of water soluble fractions of biodiesel and its diesel blends using the Salmonella assay and the in vitro MicroFlow (R) kit (Litron) assay

The designation of biodiesel as an environmental-friendly alternative to diesel oil has improved its commercialization and use. However, most biodiesel environmental safety studies refer to air pollution and so far there have been very few literature data about its impacts upon other biotic systems, e.g. water, and exposed organisms. Spill simulations in water were carried out with neat diesel and biodiesel and their blends aiming at assessing their genotoxic potentials should there be contaminations of water systems. The water soluble fractions (WSF) from the spill simulations were submitted to solid phase extraction with C-18 cartridge and the extracts obtained were evaluated carrying out genotoxic and mutagenic bioassays [the Salmonella assay and the in vitro MicroFlow (R) kit (Litron) assay]. Mutagenic and genotoxic effects were observed, respectively, in the Salmonella/microsome preincubation assay and the in vitro MN test carried out with the biodiesel WSF. This interesting result may be related to the presence of pollutants in biodiesel derived from the raw material source used in its production chain. The data showed that care while using biodiesel should be taken to avoid harmful effects on living organisms in cases of water pollution. (C) 2011 Elsevier Ltd. All rights reserved.

Kinetic of water diffusion and color stability of a resin composite as a function of the curing tip distance

The influence of curing tip distance and storage time in the kinetics of water diffusion (water sorption-W SP, solubility-W SB, and net water uptake) and color stability of a composite were evaluated. Composite samples were polymerized at different distances (5, 10, and 15 mm) and compared to a control group (0 mm). After desiccation, the specimens were stored in distilled water to evaluate the water diffusion over a 120-day period. Net water uptake was calculated (sum of WSP and WSB). The color stability after immersion in a grape juice was compared to distilled water. Data were submitted to three-way ANOVA/Tukey's test (α = 5%). The higher distances caused higher net water uptake (p < 0.05). The immersion in the juice caused significantly higher color change as a function of curing tip distance and the time (p < 0.05). The distance of photoactivation and storage time provide the color alteration and increased net water uptake of the resin composite tested.

Contribution to assessing the stiffness reduction of structural elements in the global stability analysis of precast concrete multi-storey buildings

This study deals with the reduction of the stiffness in precast concrete structural elements of multi-storey buildings to analyze global stability. Having reviewed the technical literature, this paper present indications of stiffness reduction in different codes, standards, and recommendations and compare these to the values found in the present study. The structural model analyzed in this study was constructed with finite elements using ANSYS® software. Physical Non-Linearity (PNL) was considered in relation to the diagrams M x N x 1/r, and Geometric Non-Linearity (GNL) was calculated following the Newton-Raphson method. Using a typical precast concrete structure with multiple floors and a semi-rigid beam-to-column connection, expressions for a stiffness reduction coefficient are presented. The main conclusions of the study are as follows: the reduction coefficients obtained from the diagram M x N x 1/r differ from standards that use a simplified consideration of PNL; the stiffness reduction coefficient for columns in the arrangements analyzed were approximately 0.5 to 0.6; and the variation of values found for stiffness reduction coefficient in concrete beams, which were subjected to the effects of creep with linear coefficients from 0 to 3, ranged from 0.45 to 0.2 for positive bending moments and 0.3 to 0.2 for negative bending moments.

Atomistic Study of Water Confined in Silica.

In this work, we have used a combined of atomistic simulation methods to explore the effects of confinement of water molecules between silica surfaces. Firstly, the mechanical properties of water severe confined (~3A) between two silica alpha-quartz was determined based on first principles calculations within the density functional theory (DFT). Simulated annealing methods were employed due to the complex potential energry surface, and the difficulties to avoid local minima. Our results suggest that much of the stiffness of the material (46%) remains, even after the insertion of a water monolayer in the silica. Secondly, in order to access typical time scales for confined systems, classical molecular dynamics was used to determine the dynamical properties of water confined in silica cylindrical pores, with diameters varying from 10 to 40A. in this case we have varied the passivation of the silica surface, from 13% to 100% of SiOH, and the other terminations being SiOH2 and SiOH3, the distribution of the different terminations was obtained with a Monte Carlo simulation. The simulations indicates a lowering of the diffusion coefficientes as the diameter decreases, due to the structuration of hydrogen bonds of water molecules; we have also obtained the density profiles of the confined water and the interfacial tension.

Distribution of water masses and diapycnal mixing in the Cape Verde Frontal Zone

[EN]The Cape Verde Frontal Zone separates North and South Atlantic Central Waters in the eastern North Atlantic Subtropical Gyre. CTD-O2 and shipboard ADCP data from three hydrographic sections carried out in September 2003 are used to study the structure of the front. Results show the relation between spatial variations of water masses and currents, demonstrating the importance of advection in the distribution of water masses. Diapycnal diffusivities due to double diffusion and vertical shear instabilities are also estimated. Existence of competition between the two processes through the water column is shown. Depth-averaged diffusivities suggest that salt fingering dominates diapycnal mixing, except areas of purest South Atlantic Central Water. Here, double diffusion processes are weak and, consequently, shear of the flow is the main process. Results also show that strong mixing induced by vertical shear is associated with a large intrusion found near the front.

On The Timing of Default Losses: When and Why?

At the light of what happened in 2010 and 2011, a lot of European countries founded themselves in a difficult position where all the credit rating agencies were downgrading debt states. Problem of solvency and guarantees on the states' bond were perceived as too risky for a Monetary Union as Europe is. Fear of a contagion from Greece as well was threatening the other countries as Italy, Spain, Portugal and Ireland; while Germany and France asked for a division between risky and riskless bond in order to feel more safe. Our paper gets inspiration by Roch and Uhlig (2011), it refers to the Argentinian case examined by Arellano (2008) and examine possible interventions as monetization or bailout as proposed by Cole and Kehoe (2000). We propose a model in which a state defaults and cannot repay a fraction of the old bond; but contrary to Roch and Uhlig that where considering a one-time cost of default we consider default as an accumulation of losses, perceived as unpaid fractions of the old debts. Our contributions to literature is that default immediately imply that economy faces a bad period and, accumulating losses, government will be worse-off. We studied a function for this accumulation of debt period by period, in order to get an idea of the magnitude of this waste of resources that economy will face when experiences a default. Our thesis is that bailouts just postpone the day of reckoning (Roch, Uhlig); so it's better to default before accumulate a lot of debts. What Europe need now is the introduction of new reforms in a controlled default where the Eurozone will be saved in its whole integrity and a state could fail with the future promise of a resurrection. As experience show us, governments are not interested into reducing debts since there are ECB interventions. That clearly create a distortion between countries in the same monetary union, giving to the states just an illusion about their future debtor position.

The impact of swine welfare on some qualitative traits of meat and long cured animal derived products

The present dissertation collects the results of three different research trials which have the common aim to understand the effects of swine welfare (both at farm level and during transport) on the main fresh and dry-cured meat characteristics. The first trial was carried out in order to compare the effects of illumination regimes differing in light duration or light intensity on meat and ham quality of Italian heavy pigs. The results of this trial support the conclusion that, within a moderate range of light intensity and given an appropriate dark period for animal rest, an increase of light duration or intensity above the minimum mandatory levels has no negative impact on carcass composition, meat or long-cured hams quality. The second trial was designed with the aim to investigate the effects of water restriction on growth traits, animal welfare and meat and ham quality of liquid-fed heavy pigs. Overall, the parameters analyzed as concerns growth rate, behavioural traits, blood, as well as carcass, fresh meat and cured hams quality were not affected by the absence of fresh drinking water. However, since liquid feeding did not suppress drinker use or drinker manipulation in the experimental groups, water restriction does not appear to be an applicable method to obtain a reduction of water waste. The third trial, which was carried out in Canada, tested the effectiveness of water sprinkling market-weight pigs (115±10Kg BW) before and after transport in reducing the heat stress experienced under commercial transport conditions. Our results show that the water sprinkling protocol proposed may reduce heat stress during transport and improve pork quality, particularly in specific trailer compartments. This body of research supports the general conclusion that swine welfare could be improved in different scenarios through simple and cost-effective means, without negatively affecting the quality of the main animal-derived products.

Model reduction of stochastic groundwater flow and transport processes

This work presents a comprehensive methodology for the reduction of analytical or numerical stochastic models characterized by uncertain input parameters or boundary conditions. The technique, based on the Polynomial Chaos Expansion (PCE) theory, represents a versatile solution to solve direct or inverse problems related to propagation of uncertainty. The potentiality of the methodology is assessed investigating different applicative contexts related to groundwater flow and transport scenarios, such as global sensitivity analysis, risk analysis and model calibration. This is achieved by implementing a numerical code, developed in the MATLAB environment, presented here in its main features and tested with literature examples. The procedure has been conceived under flexibility and efficiency criteria in order to ensure its adaptability to different fields of engineering; it has been applied to different case studies related to flow and transport in porous media. Each application is associated with innovative elements such as (i) new analytical formulations describing motion and displacement of non-Newtonian fluids in porous media, (ii) application of global sensitivity analysis to a high-complexity numerical model inspired by a real case of risk of radionuclide migration in the subsurface environment, and (iii) development of a novel sensitivity-based strategy for parameter calibration and experiment design in laboratory scale tracer transport.

Characterization of electromagnetic fields in the aSPECT spectrometer and reduction of systematic errors

Das aSPECT Spektrometer wurde entworfen, um das Spektrum der Protonen beimrnZerfall freier Neutronen mit hoher Präzision zu messen. Aus diesem Spektrum kann dann der Elektron-Antineutrino Winkelkorrelationskoeffizient "a" mit hoher Genauigkeit bestimmt werden. Das Ziel dieses Experiments ist es, diesen Koeffizienten mit einem absoluten relativen Fehler von weniger als 0.3% zu ermitteln, d.h. deutlich unter dem aktuellen Literaturwert von 5%.rnrnErste Messungen mit dem aSPECT Spektrometer wurden an der Forschungsneutronenquelle Heinz Maier-Leibnitz in München durchgeführt. Jedoch verhinderten zeitabhängige Instabilitäten des Meßhintergrunds eine neue Bestimmung von "a".rnrnDie vorliegende Arbeit basiert hingegen auf den letzten Messungen mit dem aSPECTrnSpektrometer am Institut Laue-Langevin (ILL) in Grenoble, Frankreich. Bei diesen Messungen konnten die Instabilitäten des Meßhintergrunds bereits deutlich reduziert werden. Weiterhin wurden verschiedene Veränderungen vorgenommen, um systematische Fehler zu minimieren und um einen zuverlässigeren Betrieb des Experiments sicherzustellen. Leider konnte aber wegen zu hohen Sättigungseffekten der Empfängerelektronik kein brauchbares Ergebnis gemessen werden. Trotzdem konnten diese und weitere systematische Fehler identifiziert und verringert, bzw. sogar teilweise eliminiert werden, wovon zukünftigernStrahlzeiten an aSPECT profitieren werden.rnrnDer wesentliche Teil der vorliegenden Arbeit befasst sich mit der Analyse und Verbesserung der systematischen Fehler, die durch das elektromagnetische Feld aSPECTs hervorgerufen werden. Hieraus ergaben sich vielerlei Verbesserungen, insbesondere konnten die systematischen Fehler durch das elektrische Feld verringert werden. Die durch das Magnetfeld verursachten Fehler konnten sogar soweit minimiert werden, dass nun eine Verbesserung des aktuellen Literaturwerts von "a" möglich ist. Darüber hinaus wurde in dieser Arbeit ein für den Versuch maßgeschneidertes NMR-Magnetometer entwickelt und soweit verbessert, dass nun Unsicherheiten bei der Charakterisierung des Magnetfeldes soweit reduziert wurden, dass sie für die Bestimmung von "a" mit einer Genauigkeit von mindestens 0.3% vernachlässigbar sind.

Geometrical optimization of a short-stem hip implant for the reduction of proximal stress shielding (ottimizzazione geometrica di uno stelo corto di protesi d?anca per la riduzione della schermatura del carico prossimale)

Nowadays the number of hip joints arthroplasty operations continues to increase because the elderly population is growing. Moreover, the global life expectancy is increasing and people adopt a more active way of life. For this reasons, the demand of implant revision operations is becoming more frequent. The operation procedure includes the surgical removal of the old implant and its substitution with a new one. Every time a new implant is inserted, it generates an alteration in the internal femur strain distribution, jeopardizing the remodeling process with the possibility of bone tissue loss. This is of major concern, particularly in the proximal Gruen zones, which are considered critical for implant stability and longevity. Today, different implant designs exist in the market; however there is not a clear understanding of which are the best implant design parameters to achieve mechanical optimal conditions. The aim of the study is to investigate the stress shielding effect generated by different implant design parameters on proximal femur, evaluating which ranges of those parameters lead to the most physiological conditions.

Prognosis of Atrial Fibrillation in Patients with Symptomatic Peripheral Arterial Disease: Data from the REduction of Atherothrombosis for Continued Health (REACH) Registry

BACKGROUND: Atrial fibrillation (AF) is a significant risk factor for cardiovascular (CV) mortality. This study aims to evaluate the prognostic implication of AF in patients with peripheral arterial disease (PAD). METHODS: The International Reduction of Atherothrombosis for Continued Health (REACH) Registry included 23,542 outpatients in Europe with established coronary artery disease, cerebrovascular disease (CVD), PAD and/or >/=3 risk factors. Of these, 3753 patients had symptomatic PAD. CV risk factors were determined at baseline. Study end point was a combination of cardiac death, non-fatal myocardial infarction (MI) and stroke (CV events) during 2 years of follow-up. Cox regression analysis adjusted for age, gender and other risk factors (i.e., congestive heart failure, coronary artery re-vascularisation, coronary artery bypass grafting (CABG), MI, hypertension, stroke, current smoking and diabetes) was used. RESULTS: Of 3753 PAD patients, 392 (10%) were known to have AF. Patients with AF were older and had a higher prevalence of CVD, diabetes and hypertension. Long-term CV mortality occurred in 5.6% of patients with AF and in 1.6% of those without AF (p<0.001). Multivariable analyses showed that AF was an independent predictor of late CV events (hazard ratio (HR): 1.5; 95% confidence interval (CI): 1.09-2.0). CONCLUSION: AF is common in European patients with symptomatic PAD and is independently associated with a worse 2-year CV outcome.

Reduction of inappropriate medications among older nursing-home residents: a nurse-led, pre/post-design, intervention study

Background: Medication-related problems are common in the growing population of older adults and inappropriate prescribing is a preventable risk factor. Explicit criteria such as the Beers criteria provide a valid instrument for describing the rate of inappropriate medication (IM) prescriptions among older adults. Objective: To reduce IM prescriptions based on explicit Beers criteria using a nurse-led intervention in a nursing-home (NH) setting. Study Design: The pre/post-design included IM assessment at study start (pre-intervention), a 4-month intervention period, IM assessment after the intervention period (post-intervention) and a further IM assessment at 1-year follow-up. Setting: 204-bed inpatient NH in Bern, Switzerland. Participants: NH residents aged ≥60 years. Intervention: The intervention included four key intervention elements: (i) adaptation of Beers criteria to the Swiss setting; (ii) IM identification; (iii) IM discontinuation; and (iv) staff training. Main Outcome Measure: IM prescription at study start, after the 4-month intervention period and at 1-year follow-up. Results: The mean±SD resident age was 80.3±8.8 years. Residents were prescribed a mean±SD 7.8±4.0 medications. The prescription rate of IMs decreased from 14.5% pre-intervention to 2.8% post-intervention (relative risk [RR] = 0.2; 95% CI 0.06, 0.5). The risk of IM prescription increased nonstatistically significantly in the 1-year follow-up period compared with post-intervention (RR = 1.6; 95% CI 0.5, 6.1). Conclusions: This intervention to reduce IM prescriptions based on explicit Beers criteria was feasible, easy to implement in an NH setting, and resulted in a substantial decrease in IMs. These results underscore the importance of involving nursing staff in the medication prescription process in a long-term care setting.