Horizontale Trennblätter in Trawls zur Verringerung von Discards in der Ostsee

A primary objective of the Common Fishery Policy of the European Union is the reduction of discards and unwanted by-catches in the fishery. In principle this could be achieved if the catching methods were optimised for this. Still high numbers of undersized flatfish are caught in the bottom trawls. Although EU regulations make the use of the BACOMA codend mandatory in the Baltic Sea cod areable to escape through square mesh escape window of the BACOMA net the whereas flatfish still remain in the cod-end. Gear experiments have been carried out with the aim to better separate cod from the flatfish fraction already when entering the rear belly, making use of the natural behaviour of the fish, i. e. the preferred swimming distance from the bottom of the net in the funnel. As cod have a natural tendency to keep a relativly great distance from the bottom, flatfish tend to stay close to it. It was attempted to separate both fractions by splitting the funnel into an upper and lower part with a horizontal panel. This wastested for two different nets, a cod trawl to separate cod from flatfish, and an eel-trawl to separate cod and flatfish from eel. Cod and flatfish separation is best at a panel distance of 50 cm from the bottom. Thus, 74 % of the cod were found in the upper panel, whereas 75 % of the flounder were in the lower section. A separation of eel from cod was however not possible, since eel tend to rise to the upper part of the net, together with cod.

The BACOMA cod-end. History and recent developments in BACOMA cod-end regulations and a proposal for abetter specification of the BACOMA cod-end for Baltic Sea cod fishery

To improve the cod stocks in the Baltic Sea, a number of regulations have recently been established by the International Baltic Sea Fisheries Commission (IBSFC) and the European Commission. According to these, fishermen are obliged to use nets with escape windows (BACOMA nets) with a mesh size of the escape window of 120 mm until end of September 2003. These nets however, retain only fish much larger than the legal minimum landing size would al-low. Due to the present stock structure only few of such large fish are however existent. As a consequence fishermen use a legal alternative net. This is a conventional trawl with a cod-end of 130 mm diamond-shaped meshes (IBSFC-rules of 1st April 2002), to be increased to 140 mm on 1st September 2003, according to the mentioned IBSFC-rule. Due legal alterations of the net by the fishermen (e.g. use of extra stiff net material) these nets have acquired extremely low selective properties, i. e. they catch very small fish and produce great amounts of discards. Due to the increase of the minimum landing size from 35 to 38 cm for cod in the Baltic, the amount of discards has even increased since the beginning of 2003. Experiments have now been carried out with the BACOMAnet on German and Swedish commercial and research vessels since arguments were brought forward that the BACOMA net was not yet sufficiently tested on commercial vessels. The results of all experiments conducted so far, are compiled and evaluated here. As a result of the Swedish, Danish and German initiative and research the European Commission reacted upon this in June 2003 and rejected the increase of the diamond-meshed non-BACOMA net from 130 mm to 140mm in September 2003. To protect the cod stocks in the Baltic Sea more effectively the use of traditional diamond meshed cod-ends with-out escape window are prohibited in community waters without derogation, becoming effective 1st of September 2003. To enable more effective and simplified control of the bottom trawl fishery in the Baltic Sea the principle of a ”One-Net-Rule“ is enforced. This is going to be the BACOMA net, with the meshes of the escape window being 110 mm for the time being. The description of the BACOMA net as given in the IBSFC-rules no.10 (revision of the 28th session, Berlin 2002) concentrates on the cod-end and the escape window but only to a less extent on the design and mesh-composition of the remaining parts of the net, such as belly and funnel and many details. Thus, the present description is not complete and leaves, according to fishermen, ample opportunity for manipulation. An initiative has been started in Germany with joint effort from scientists and the fishery to better describe the entire net and to produce a proposal for a more comprehensive description, leaving less space for manipulation. A proposal in this direction is given here and shall be seen as a starting point for a discussion and development towards an internationally uniform net, which is agreed amongst the fishery, scientists and politicians. The Baltic Sea fishery is invited to comment on this proposal, and recommendations for further improvement and specifications are welcomed. Once the design is agreed by the Baltic Fishermen Association, it shall be proposed to the IBSFC and European Commission via the Baltic Fishermen Association.

Untersuchungen des Zanderbestandes in den deutschen Küstengewässern der Ostsee von 1992 bis 2002

Pike-perch is an important resource for the coastal fishery in the brackish waters of the eastern part of the coast. For the conservation of the stocks regulation measures (minimum landing size, closed season and minimum mesh size) have been introduced since many years. Basic biological material of the last decade sampled from the commercial fishery and for recruitment by a standard trawl survey. For the “Eastern stock” this paper presents the results concerning age distribution, year-class strengths, growth, proportion spawners, natural mortality and yield-per-recruit analyses.

Ein neues Messgerät zur Kontrolle der Maschenöffnung in der Fischerei

At present both the wedge gauge and the ICES mesh gauge are used to examine the mesh opening of trawl cod-ends. A thorough investigation of both instruments by an EU project (MESH) has revealed a number of deficiencies. This has lead to the conclusions to not further recommend the use of both devices but to go for the development of a complete new measurement tool. This is presently progressing in a further EU project named OMEGA. Prototypes of the new device have been produced and a number of introductory tests have already been made. This contribution reports on further laboratory tests carried out at the Institute for Fishing technology and Fish Quality with special emphasis on netting yarn diameters below 4 mm. The results demonstrate further yarn size depending inaccuracies of the wedge gauge and support the rapid introduction of the newly developed measurement instrument.

Aktuelle Planungen zur Regelung der Beifangproblematik in der Krabbenfischerei

At present the fishery for the brown shrimp (Crangon crangon L.) is one of the most economically rewarding fisheries in Europe. Due to the small size of the target objects this fishery has to be carried out with rather small meshes. As it is, however, performed on the nursing grounds of important fish species it encounters a severe bycatch problem. On this basis, EU Council regulation 850/98 demands the use of either sieve nets or sorting grids from 1 July, and to pass pertaining national bye-laws. Germany discusses to use either sieve nets of 70 mm mesh opening or sorting grids of 20 mm bar distance, and tries to achieve a harmonization of the byelaw with neighbouring countries of The Netherlands and Denmark to ensure equal conditions on the same fishing grounds.

Ist die Steigerung des dauerhaften Fischereiertrages durch Maschengrößenoptimierung möglich?

The management of a fish aimed at maximising the fishing yield of the managed fish stock. There are models for the yield optimisation since long time. They are used so far mainly to optimise the fishing mortality. Starting point of this paper is a number of fish of an age group of a fish stock. This age group is accompanied over its lifetime. A result of the investigations is that the term growth over-fishing is linked not as frequently assumed exclusive with a too large fishing mortality, but likewise with a mismatch of the mesh opening. The investigations show that the fishing yield increases with the fishing effort on condition that fishing is carried out with an optimised mesh opening. For the calculated example Baltic cod data are used. At present the cod is caught far before reaching the yield optimum. Now the fish is substantially too small when it is caught and did not reach its optimal mass at this time. Therefore the sustainable fishing yield could be increased considerably by the optimasation of the mesh opening. During the conversion from the state of the art to fishing with optimised mesh sizes, however, a loss of profit has to be expected. A further advantage of the mesh enlargement is an increase of the spawning stock size accompanying with it, since the fish is caught at a later age. By the use of substantially larger mesh openings the cod has the opportunity to spawn several times and generate descendants and this will also lead to an increased yield in future. In addition better prices could be obtained at the market by catching larger cod.

Weitere Selektionsuntersuchungen an Schleppnetzsteerten für den Plattfischfang in der Ostsee

The presentation includes investigations and results regarding Baltic flatfish selectivity with different trawl codend constructions. These investigations were carried out 1999/ 2000 on board of FRV “Clupea” and a commercial 17 m cutter. As could be shown, both an enlarged mesh size and another mesh form than rhombic can improve the selectivity of these fish. As flatfish catches with trawls mostly also cover cod, this mixed fishery at the southern Baltic coast should in future be managed by differentiated technical regulations for an improved selectivity. The results, also based on UW observations, current measurements, and wind tunnel tests with models, demonstrate some possible technical solutions.

Ostseedorschselektion - bestehende und vorgesehene neue technische Maßnahmen

Since the beginning of the nineties the situation of the Baltic cod stock is deteriorating constantly. The fishery administration (International Baltic Sea Fisheries Commission) tries to counter this by issuing new technical measures. Existing measures (raise of mesh opening from 105 to 120 mm, “Danish” and “Swedish” escape windows) and newly introduced technical measures (BACOMA codend and raise of the mesh opening in conventional codends to 130 mm) show a number of deficiencies putting their efficiency in doubt. Available well tested alternatives to the newly introduced measures without their negative side effects (codends made of netting turned by 90°, and other designs) are presently left out of regard. Models of socioeconomic effects are likewise ignored.

Techno-economic considerations of shark driftnet fishery, off Lagos coast, Nigeria

Experimental fishing operations with driftnets were conducted in Lagos coastal waters with a view to finding out appropriate gear for effective exploitation of sharks and other pelagic fish species that are not normally caught in trawls. The design and fabrication of the driftnets as well as the fishing trials were undertaken between May, 1977 and April, 1978. Six baited driftnet sets of equal panels with three stretched mesh sizes of 190.5mm; 228.6mm and 241.3mm were used. Analysis were carried out on species composition of catches, weight and number of species/group of fish, catch efficiency of the driftnets as well as on operating costs and financial returns

Neues aus der Selektionsforschung am Ostseedorsch

In account of the decision of the IBSFC (International Baltic Sea Fisheries Commission) to admit alternative codend constructions to the presently legal of diamond meshes with 120 mm mesh opening, since seven years a vivid research activity is encouraged at the fishing technology institutions around the Baltic. Though a center of gravity in this field of research lies in the EUproject BACOMA (participants Finland Sweden, Denmark) also the corresponding national institutes of other Baltic countries (Germany, Poland, Russia) have been active with similar investigations. German experiments in 1999 dealt with the effect of the use of netting made of double instead of single yarn on the selectivity. Further research was done on modifications of codends made from netting turned 90° from its original orientation and on simplified versions of the so-called Multipanel codend which consists of three equal diamond and three square mesh panels. The experiments demonstrated on the one hand a definite deterioration of the selective properties in a codend made from double instead of single yarn. Constructional changes in codends made from netting turned 90° on the other hand brought a further improvement of the selectivity of such codends. Finally, the investigations on the Multipanel codend revealed the overwhelming influence of the square mesh panels on the selectivity success. If in a conventional diamond codend three windows are cut out starting 50 cm from the real end of the codend in such a way that the remaining parts have the same breadth as the square mesh panels to insert, the selective effect of such a codend is remarkably improved. According to further preliminary tests this seems to be nearly independent from the type of material used.

Analyse der Beifangreduktion durch Trichternetze in der kommerziellen Garnelenfischerei

Trials for the determination of the magnitude of bycatch reduction by the sievenets used in the commercial brown shrimp fishery were carried out from September to December 1997. Trawls with 9 m beam length were the subjected to the investigation. They were used on different fishing grounds in the estuary of the Elbe near Cuxhaven. Sievenets with 50, 60 and 80 mm mesh opening were tested in 29 hauls and 31.6 h total duration. A trawl of equal construction without sievenets fished synchronously was used for comparison. The proportional catch composition in the codend was determined by weighing the catch components (fish, discard shrimps and commercial size shrimps) as separated by means of a riddle. The composition of the sorted out part of the catch could be calculated by comparison of the corresponding catch components both in standard trawl and sievenettrawl. According to this the total catch of a beam trawl with sievenet is diminished by 9 to 34 % depending on the mesh opening of the sievenet. 32 to 58 % of the sorted out part of the catch consists of fish. Use of a sievenet, however, also leads to a loss of 6 to 15 % of commercial size shrimps. Per hour of towing this means a loss of 8.7 kg commercial size shrimps with a sievenet of 60 mm mesh opening and of 1.8 kg for a mesh size of 80 mm.

Numerical Investigation On The Flowfield Of "Swallowtail" Cavity For Supersonic Mixing Enhancement

A "swallowtail" cavity for the supersonic combustor was proposed to serve as an efficient flame holder for scramjets by enhancing the mass exchange between the cavity and the main flow. A numerical study on the "swallowtail" cavity was conducted by solving the three-dimensional Reynolds-averaged Navier-Stokes equations implemented with a k-epsilon turbulence model in a multi-block mesh. Turbulence model and numerical algorithms were validated first, and then test cases were calculated to investigate into the mechanism of cavity flows. Numerical results demonstrated that the certain mass in the supersonic main flow was sucked into the cavity and moved spirally toward the combustor walls. After that, the flow went out of the cavity at its lateral end, and finally was efficiently mixed with the main flow. The comparison between the "swallowtail" cavity and the conventional one showed that the mass exchanged between the cavity and the main flow was enhanced by the lateral flow that was induced due to the pressure gradient inside the cavity and was driven by the three-dimensional vortex ring generated from the "swallowtail" cavity structure.

An Improved Ce/Se Scheme For Multi-Material Elastic-Plastic Flows And Its Applications

In this paper, a new definition of SE and CE, which is based on the hexahedron mesh and simpler than Chang's original CE/SE method (the space-time Conservation Element and Solution Element method), is proposed and an improved CE/SE scheme is constructed. Furthermore, the improved CE/SE scheme is extended in order to solve the elastic-plastic flow problems. The hybrid particle level set method is used for tracing the interfaces of materials. Proper boundary conditions are presented in interface tracking. Two high-velocity impact problems are simulated numerically and the computational results are carefully compared with the experimental data, as well as the results from other literature and LS-DYNA software. The comparisons show that the computational scheme developed currently is clear in physical concept, easy to be implemented and high accurate and efficient for the problems considered. (C) 2008 Elsevier Ltd. All rights reserved.

A Hybrid Scheme Based on Finite Element/Volume Methods for Two Immiscible Fluid Flows

We have successfully extended our implicit hybrid finite element/volume (FE/FV) solver to flows involving two immiscible fluids. The solver is based on the segregated pressure correction or projection method on staggered unstructured hybrid meshes. An intermediate velocity field is first obtained by solving the momentum equations with the matrix-free implicit cell-centered FV method. The pressure Poisson equation is solved by the node-based Galerkin FE method for an auxiliary variable. The auxiliary variable is used to update the velocity field and the pressure field. The pressure field is carefully updated by taking into account the velocity divergence field. This updating strategy can be rigorously proven to be able to eliminate the unphysical pressure boundary layer and is crucial for the correct temporal convergence rate. Our current staggered-mesh scheme is distinct from other conventional ones in that we store the velocity components at cell centers and the auxiliary variable at vertices. The fluid interface is captured by solving an advection equation for the volume fraction of one of the fluids. The same matrix-free FV method, as the one used for momentum equations, is used to solve the advection equation. We will focus on the interface sharpening strategy to minimize the smearing of the interface over time. We have developed and implemented a global mass conservation algorithm that enforces the conservation of the mass for each fluid.

An Improved CE/SE Scheme for Numerical Simulation of Gaseous and Two-Phase Detonations

A new structure of solution elements and conservation elements based on rectangular mesh was pro- posed and an improved space-time conservation element and solution element (CE/SE) scheme with sec- ond-order accuracy was constructed. Furthermore, the application of improved CE/SE scheme was extended to detonation simulation. Three models were used for chemical reaction in gaseous detonation. And a two-fluid model was used for two-phase (gas–droplet) detonation. Shock reflections were simu- lated by the improved CE/SE scheme and the numerical results were compared with those obtained by other different numerical schemes. Gaseous and gas–droplet planar detonations were simulated and the numerical results were carefully compared with the experimental data and theoretical results based on C–J theory. Mach reflection of a cellular detonation was also simulated, and the numerical cellular pat- terns were compared with experimental ones. Comparisons show that the improved CE/SE scheme is clear in physical concept, easy to be implemented and high accurate for above-mentioned problems.