Validação de protocolo de assistência para pessoas com úlcera venosa na atenção primária

People with venous ulcers constitute as an important public health problem, its treatment is onerous and require assistance provided by trained professionals, systematized through protocols, however what lies in the assistance is that the management of this group of people differs from that preconized in the scientific literature, interfering with wound healing and quality of life of affected. In this sense, the construction of a assistance protocol specific to people with venous ulcers (VU) can help professionals of the Family Health Strategy both in patient assessment as and in establishment of quality assistance. Thus, this study aimed to analyse the validity of a multiprofessional assistance protocol for people with venous ulcers in primary care by health professionals using Delphi technique. This is a quantitative study, the methodological type conducted in two steps: first step related to integrative literature review to subsidize the development of the protocol, then these aspects were organized and proposed to the judges of the study through the Delphi technique. The study was initiated after approval by the Research Ethics Committee. The first step was performed between August and September 2012, in the virtual library of health, in the page of the Coordination of Improvement of Higher Education Personnel, of Municipal Health Secretariat and international guidelines of associations and in the subsequent step carried out between September 2012 to January 2013, was performed search by Lattes platform of the National Council of Technological and Scientific Development, in order to identify health professionals in Brazil who act as judges of the instrument and then, via online, the form was submitted to them.The sample for the second step was 51 judges in the first round and 35 for the second round Delphi. The analysis was done by adopting Kappa index ≥ 0.81 and Content Validity Index (CVI)> 0.80. In the first submission for the judges, items that did not reach Kappa and CVI established were: request / realization / test results, demographic data, medical history, risk factors, verification of pain / vital signs / pulse / infection signs / lesion location/ edema and pain treatment. After removal of items which have not obtained Kappa or CVI index established, it was found achieving optimal levels of these index for the categories. In the next step was the ressubmissão of protocol to judges through the Delphi technique in it was found that, of the 15 categories of the protocol, 12 presented higher scores in Delphi 2 phase and the other three categories remained the same Kappa and IVC of the previous phase. As for the average of evaluation requirements of the protocol was found that the scores assigned by the judges were higher in the second phase in nine of the 10 items, remaining the same in only one of the items indicating validity of the instrument before the consensus of the judges. Thus, we accepted the alternative hypothesis in this study, as they were obtained in the second Delphi phase the validity index greater than or equal to the Delphi 1 phase. The formulation of this assistance protocol valid and reproducible will enable a reorganization and redesign of assistance, with standardization of actions and continuity of care for persons with venous ulcers in primary health care

Desenvolvimento de equipamentos para o mapeamento de áreas infestadas por macrófitas aquáticas imersas

Foi desenvolvido um conjunto de equipamentos com o objetivo de mapear as áreas infestadas por macrófitas aquáticas, auxiliando operações de manejo mecânico, as quais são realizadas por uma colhedora desenvolvida especificamente para essa finalidade. O conjunto de equipamentos foi constituído por um GPS com programa de correção diferencial, acoplado a um palmtop, um sistema com dois teclados ligados em dataloggers e um transdutor de deslocamento linear LT. O GPS, através do palmtop, proporcionava o mapeamento da área de deslocamento, auxiliando o operador na movimentação da máquina, otimizando a operação e evitando, dessa forma, a sobreposição das faixas de coleta na área a ser manejada. Um dos teclados monitorava a movimentação e operação da colhedora, além da presença de obstáculos, como tocos e bancos de areia, enquanto o outro gerava dados sobre a presença de determinada espécie de planta, como E. densa, E. najas e C. demersum, além do nível de infestação destas plantas. O transdutor, instalado na plataforma frontal da colhedora, se movimentava linearmente, gerando informações sobre a profundidade da coleta realizada. Dessa forma, pôde-se observar que o desenvolvimento desse conjunto de equipamentos foi de grande utilidade e auxiliou a operação de controle mecânico de áreas infestadas por macrófitas aquáticas imersas, possibilitando, assim, o planejamento de operações de manejo e controle subseqüentes.

Fontes e períodos de contato de fertilizantes e germinação de sementes de Brachiaria brizantha

A mistura de sementes forrageiras com fertilizantes pode viabilizar o cultivo consorciado, por diminuir a competição com a cultura produtora de grãos. No entanto, se realizada muito antes da semeadura, pode prejudicar a emergência e o estabelecimento das forrageiras. Realizou-se trabalho em condições de laboratório e casa de vegetação, em Botucatu (SP), com o objetivo de avaliar a germinação de sementes de Brachiaria brizantha em razão do tempo de mistura com fertilizantes químicos. O delineamento experimental empregado foi o inteiramente casualizado, com quatro repetições. Os tratamentos constaram de um fatorial 6 x 8, constituído de diferentes períodos de contato das sementes de Brachiaria brizantha cultivar Marandu (0, 6, 12, 24, 48 e 96 h) com os fertilizantes uréia, sulfato de amônio, cloreto de potássio, sulfato de potássio, superfosfato simples, superfosfato triplo e formulado N-P-K (8-28-16) nas formas de mistura de grânulos e farelado. Não houve relação entre os testes de germinação em laboratório e a emergência a campo. No solo, a emergência das plântulas de Brachiaria brizantha não é afetada se realizada a mistura com fertilizantes minerais fosfatados, cloreto de potássio e formulado farelado até 96 h antes da semeadura.

Purificação da glicerina bruta obtida a partir da transesterificação do óleo de algodão

The crude glycerine is a raw material that can be used in a wide variety of products. Even with all the impurities inherent in the process of being obtained, the crude glycerin is already in a marketable product. However, the market is much more favorable to the commercialization of purified glycerine. The glycerin is a byproduct gotten from the process of transesterification of waste oils and fats in the production of biodiesel. More recently, the deployment of the new Federal Law of Brazil, related to the implementation of energy resources, forces, from 2008, the increase of 2% biodiesel in diesel common with prospects for 5% (B5). Therefore, it is indispensable that new routes of purification as well as new markets are developed. The objective of this work was to purify, through ion exchange, the crude glycerin, obtained from the reaction of transesterification of cottonseed oil. The cottonseed oil was characterized as the fatty acid composition and physical-chemical properties. The process of ion exchange was conducted in batch. In this process were used strong cation, low anion resins and a mixed resin used to de-ionize water. The purified glycerin was characterized as the content of metals. Tests were performed with activated charcoal adsorption, and for this, it was made tests of time contact with coal as well as quantity of coal used. The time of activation, the amount of the activation solution, the contact time of the glycerol solution in resins, the amount and type of resin applied were evaluated. Considering the analysis made with activated charcoal, when the glycerin solution was treated using the resins individually it was observed that in the conditions for treatment with 10 g of resin, 5 hours of contact with each resin and 50 mL of glycerin solution, its conductivity decreased to a cationic resin, increased to the anionic resin and had a variable value with respect to resin mixed. In the treatment in series, there was a constant decrease in the conductivity of the solution of glycerin. Considering two types of treatment, in series and individually, the content of glycerol in glycerin pre-purified solution with the different resins varied from 12,46 to 29.51% (diluted solution). In analysis performed without the use of activated charcoal, the behavior of the conductivity of the solution of glycerin were similar to results for treatment with activated charcoal, both in series as individually. The solution of glycerin pre-purified had a glycerol content varying from 8.3 to 25.7% (diluted solution). In relation to pH, it had a behavior in accordance with the expected: acid for the glycerin solution treated with cationic resin, basic when the glycerin solution was treated with the anionic resin and neutral when treated with the mixed resin, independent of the kind of procedure used (with or without coal, resins individually or in series). In relation to the color of the glycerin pre-purified solution, the resin that showed the best result was the anionic (colorless), however this does not mean that the solution is more in pure glycerol. The chromatographic analysis of the solutions obtained after the passage through the resins indicated that the treatment was effective by the presence of only one component (glycerol), not considering the solvent of the analysis

Avaliação da molhabilidade de soluções de tensoativos em aço inoxidável

With the increasing industrialization of the planet caused by globalization, it has become increasingly common to search for highly resistant and durable materials for many diverse branches of activities. Thus, production and demand for materials that meet these requirements have constantly increased with time. In view of this, stainless steel is presented as one of the materials which are suitable applications, due to many features that are interesting for several segments of the industry. Concerns of oil companies over heavy oil reservoirs have grown steadily for the last decades. Rheological properties of these oils impair their transport in conventional flow systems. This problem has created the need to develop technologies to improve flow and transport, reducing operation costs so as to enable oil production in the reservoir. Therefore, surfactant-based chemical systems are proposed to optimize transport conditions, effected by reduction of interfacial tensions, thereby enhancing the flow of oil in ducts and reducing load losses by friction. In order to examine such interactions, a study on the wettability of metallic surfaces has been undertaken, represented by measuring of contact angle of surfactant solutions onto flat plates of 304 stainless steel. Aqueous solutions of KCl, surfactants and mixtures of surfactants, with linear and aromatic hydrocarbon chain and ethoxylation degrees ranging between 20 to 100, have been tested. The wettability was assessed by means of a DSA 100 krüss goniometer. The influence of roughness on the wettability was also investigated by machining and polished the stainless steel plates with sandpapers of references ranging between 100 of 1200. The results showed that sanding and polishing plates result in decrease of wettability. As for the solutions, they have provided better wettability of the stainless steel than the KCl solutions tested. It was also been concluded that surfactant mixtures is an option to be considered, since they promote interactions that generate satisfactory contact angles for a good wettability on the stainless steel plate. Another conclusion refers to the influence of the ethoxylation degree of the nonionic surfactant molecules on wettability. It has been observed that contact angles decrease with decreasing ethoxylation degrees. This leads us to conclude that molecules with higher ethoxylation degree, being more hydrophobic, decrease the interaction of water with the ducts, thereby reducing friction and improving the flow

Preparação e caracterização de um material híbrido, à base de vermiculita modificada com quitosana, para a remoção de íons de chumbo presentes em efluentes sintéticos

Actually, surveys have been developed for obtaining new materials and methodologies that aim to minimize environmental problems due to discharges of industrial effluents contaminated with heavy metals. The adsorption has been used as an alternative technology effectively, economically viable and potentially important for the reduction of metals, especially when using natural adsorbents such as certain types of clay. Chitosan, a polymer of natural origin, present in the shells of crustaceans and insects, has also been used for this purpose. Among the clays, vermiculite is distinguished by its good ion exchange capacity and in its expanded form enhances its properties by greatly increasing its specific surface. This study aimed to evaluate the functionality of the hybrid material obtained through the modification of expanded vermiculite with chitosan in the removal of lead ions (II) in aqueous solution. The material was characterized by infrared spectroscopy (IR) in order to evaluate the efficiency of modification of matrix, the vermiculite, the organic material, chitosan. The thermal stability of the material and the ratio clay / polymer was evaluated by thermogravimetry. To evaluate the surface of the material was used in scanning electron microscopy (SEM) and (BET). The BET analysis revealed a significant increase in surface area of vermiculite that after interaction with chitosan, was obtained a value of 21, 6156 m2 / g. Adsorption tests were performed according to the particle size, concentration and time. The results show that the capacity of removal of ions through the vermiculite was on average 88.4% for lead in concentrations ranging from 20-200 mg / L and 64.2% in the concentration range of 1000 mg / L. Regarding the particle size, there was an increase in adsorption with decreasing particle size. In fuction to the time of contact, was observed adsorption equilibrium in 60 minutes with adsorption capacity. The data of the isotherms were fitted to equation Freundlich. The kinetic study of adsorption showed that the pseudo second- order model best describes the adsorption adsorption, having been found following values K2=0,024 g. mg-1 min-1and Qmax=25,75 mg/g, value very close to the calculated Qe = 26.31 mg / g. From the results we can conclude that the material can be used in wastewater treatment systems as a source of metal ions adsorbent due to its high adsorption capacity

Estudo da produção de pectinase por fermentação em estado sólido utilizando pedúnculo de caju como substrato

Pectinolytic enzymes, or simply pectinases, are complex enzymes that degrade pectic polymers. They have many uses, such as fruit juice extraction and purification, textile fiber treatment and vegetal oil extraction. The aim of this work was to study the kinetics of pectinases production by solid-state fermentation, using dry cashew apple residue as substrate and the microorganism Aspergillus niger CCT 0916. The influence of the initial medium moisture and medium supplementation with a source of nitrogen and phosphorus was evaluated using the factorial experimental planning and response surface methodology. Ammonia sulphate and potassium phosphate were used as nitrogen and phosphorus source, respectively. The variables time of contact (T) and ratio volume solvent/fermented medium (RZ), in systems with and without agitation, were evaluated in order to study the best extraction condition of the produced enzyme. Washed and unwashed cashew apple residues were tested as the growth medium. The unwashed residue was obtained by drying the residue after the extraction of the juice, while the washed residue was obtained by water washing 5 times using the proportion of 1 kg pulp/2 liters of water. Samples were taken every 12 hours for moisture content, pH, protein, reducing sugars, polygalacturonase activity (PG) and viscosity reduction. The physical-chemical composition of the residues had different sugar and pectin levels. For the unwashed residue, the peak activity was reached with 40% of initial moisture content, 1% of nitrogen supplementation without phosphorus addition after 30 hours of process. These conditions led to 16 U/g of PG activity and 82% of viscosity reduction. The calculated models reached similar values to the experimental ones in the same process conditions: 15.55 U/g of PG and 79.57% of viscosity eduction. Similarly, the greatest enzyme production for washed residue was reached with 40% initial moisture content, 1% nitrogen supplementation without phosphorus addition after 22 hours of cultivation. In this condition it was obtained polygalacturonase activity of 9.84 U/g and viscosity reduction of 81.36%. These values are close to experimental values that were of 10.1 U/g and 81%, respectively. The conditions that led to the best PG activity results was the agitated one and the best extraction condition was obtained with 100 minutes of solvent/medium contact and RZ of 5 (mL/g)

Ensaios de tratabilidade aplicados a determinação de parâmetros para dimensionamento de processos de tratamento de água de manancial eutrofizado

Eutrophication is a growing process present in the water sources located in the northeast of Brazil. Among the main consequences of these changes in trophic levels of a water source, stands out adding complexity to the treatment to achieve water standards. By these considerations, this study aimed to define, on a laboratory scale, products and operational conditions to be applied in the processing steps using raw water from Gargalheiras dam, RN, Brazil. The dam mentioned shows a high number of cyanobacteria, with a concentration of cells / ml higher than that established by Decree No. 518/04 MS. The same source was also considered by the state environmental agency in 2009 as hypereutrophic. The static tests developed in this research simulated direct filtration (laboratory filters) and pre-oxidation with chlorine and powdered activated carbon adsorption. The research included the evaluation of the coagulants aluminum hydrochloride (HCA) and alum (SA). The development of the research investigated the conditions for rapid mixing, the dosages of coagulants and pHs of coagulation by the drawing of diagrams. The interference of filtration rate and particle size of filtering means were evaluated as samples and the time of contact were tested with chlorine and activated carbon. By the results of the characterization of the raw water source it was possible to identify the presence of a high pH (7.34). The true color was significant (29 uH) in relation to the apparent color and turbidity (66 uH and 13.60 NTU), reflecting in the measurement of organic matter: MON (8.41 mg.L-1) and Abs254 (0.065 cm-1). The optimization of quick mix set time of 17", the speed gradient of 700 s-1 in the coagulation with HCA and the time of 20" with speed gradient of 800 s-1 for SA. The smaller particle sizes of sand filtering means helped the treatment and the variation in filtration rate did not affect significantly the efficiency of the process. The evaluation of the processing steps found adjustment in standard color and turbidity of the Decree nº 518/04 MS, taking in consideration the average values found in raw water. In the treatment using the HCA for direct filtration the palatable pattern based on the apparent color can be achieved with a dose of 25 mg L-1. With the addition of pre-oxidation step, the standard result was achieved with a reduced dose for 12 mgHCA.L-1. The turbidity standard for water was obtained by direct filtration when the dose exceeds 25 mg L-1 of HCA. With pre-oxidation step there is the possibility of reducing the dose to 20 mg L-1.The addition of CAP adsorption, promoted drinking water for both parameters, with even lower dosage, 13 mg L-1 of HCA. With coagulation using SA removal required for the parameter of apparent color it was achieved with pre-oxidation and 22 mgSA.L-1. Despite the satisfactory results of treatment with the alum, it was not possible to provide water with turbidity less than 1.00 NTU even with the use of all stages of treatment

Determinacão do período orbital de sistemas binários clipsantes

In this work is presented a new method for the determination of the orbital period (Porb) of eclipsing binary systems based on the wavelet technique. This method is applied on 18 eclipsing binary systems detected by the CoRoT (Convection Rotation and planetary transits) satellite. The periods obtained by wavelet were compared with those obtained by the conventional methods: box Fitting (EEBLS) for detached and semi-detached eclipsing binaries; and polynomial methods (ANOVA) for contact binary systems. Comparing the phase diagrams obtained by the different techniques the wavelet method determine better Porb compared with EEBLS. In the case of contact binary systems the wavelet method shows most of the times better results than the ANOVA method but when the number of data per orbital cicle is small ANOVA gives more accurate results. Thus, the wavelet technique seems to be a great tool for the analysis of data with the quality and precision given by CoRoT and the incoming photometric missions.

Caracterização do ritmo de atividade motora durante a puberdade em sagüis (Callithrix jacchus) sob condições semi-naturais

Most of ontogenetic studies on circadian timing system have been developed on infants, adults and elderly. The puberty has not been a stage of life few studied, except for researches in human adolescents, that presents phase delay in sleep-wake cycle. However, few studies have focused on the basis of this circadian change due to methodological difficulties. Thus, an animal model to study the sleep-wake cycle at puberty is essential. In the common marmoset, a social primate, the circadian activity periodicity stabilizes around 4 months (juvenile stage) and the 8h period component has a seasonal variation. Puberty stage of this species begins near the 8th month of age in males and near the 7th month in females with 7 months of duration. With the aim to characterize the circadian motor activity rhythm during puberty in marmosets (Callithrix jacchus) the motor activity was continuous registered by actiwatches in 6 animals between 5-12 months. Since the social factor influence the behavior of this specie, behavioral observations were realized in 30 minutes windows twice/week to a general evaluation of the influence social interactions dynamic across experiment. Determination of puberty onset was done by fecal progesterone and estrogens in females, and androgens in males. From the analysis of the multiple regression test was selected a model that evaluate age and seasonal variables effect on the activity rhythm according to the higher explanation coefficient. The total activity was the only parameter influenced by age. Moreover, the activity onset was the parameter more explained by the model, and the sunrise was the factor that most influenced it. After the puberty onset, 2 dyads advanced the activity onset. The activity total decreased in 1 dyad and increased in 2 dyads. This increase may be related to the birth of infants in these families. The motor activity circadian component stabilized later in 1 dyad, coinciding with the puberty onset of these animals, while bimodality, caused by the 8 h component, was modulated by seasonality. The agonistic behavior was not evaluated due to reduced number of events. There were changes across ages in affiliative behavior of contact in 1 dyad, grooming done in 1 animal and grooming received in 2 animals. Although there is evidence of puberty effect on the activity motor rhythm, the photoperiodic fluctuations influenced the rhythm. Therefore is not possible to affirm if the puberty modulate the activity rhythm in marmosets

Efeito do exercício físico matinal realizado sob luz solar no ciclo vigília-sono de adolescentes

The sleep onset and offset delay at adolescence in relation to childhood. Besides biological causes, some external factors as academic obligations and socialization contributes, increasing the burden of school and socialization. However, morning school schedules reduce sleep duration. Besides light strong effect, studies in humans have indicated that exercise influence circadian synchronization. To evaluate the effect of the morning exercise under sunlight on sleep-wake cycle (SWC) of adolescents, 160 high school students (11th year) were exposed to the following conditions: lesson in usual classroom (Group C), lesson in swimming pool exposed to sunlight (Group E), half of them carrying through physical activity (EE) and the other resting (EL). Each experimental group met two stages: assessment of SWC 1 week before and 1 week during the intervention, which was held in Monday and Wednesday between 7:45 and 8:30 am. In the baseline, there were applied the questionnaires "Health and Sleep" and cronotype evaluation (H & O). In addition, students were evaluated before and during the intervention by "Sleep Diary", "Karolinska Sleepiness Scale" (KSS), Psychomotor Vigilance Test (PVT) and actimetry. During the intervention, there was a delay in wake-up time on the weekend and a trend to greater sleep duration on week for the three groups. At the weekend, only the groups EE and EL increased sleep duration. There was no difference in bedtime, irregularity of sleep schedules and nap variables. The sleepiness showed a circadian pattern characterized by higher alertness levels at 11:30 am and sleepiness levels at bedtime and wake-up time on week. On weekends there were higher levels of alertness in these times. In the days of intervention, there was an increase of sleepiness at 11:30 am for groups EL and EE, which may have been caused by a relaxing effect of contact with the water of the pool. In addition, the group EE showed higher alert levels at 14:30 pm on Monday and at 8:30 am in the Wednesday, possibly caused by exercise arousal effect. The reaction time assessed through the TPV did not vary between the stages. The sleep quality improved in the three groups in the second stage, making impossible the evaluation of intervention effect. However, the sleep quality increased on Monday and Tuesday only on the group EE. From the results, it is suggested that the intervention promoted effects on the sleepiness at some day hours. In other SWC variables there were no effects, possibly due to a large SWC irregularity on weekends. Thus, the evaluation of higher weekly frequency EF is necessary, since only two days were insufficient to promote greater effect on adolescents SWC

Uso da palha de carnaúba em revestimento de dutos

In this work, the plant species Copernicia prunifera (Miller) H. E. Moore (carnauba), naturally occurring which prevails in the northeast region of Brazil was the subject of studies aiming its use as external coating of pipelines used in petroleum industry. The part of the plant worked were the leaves, also called straw, which were coated with resinous material. For this purpose, it was necessary to evaluate the effectiveness of the use of acrylic resins in the straw carnauba coating. The properties of the untreated carnauba straw and chemically treated with sodium hydroxide, hexane and carbon tetrachloride were investigated by ATRFTIR, SEM and thermal analysis. The first two techniques showed that treatment with solvents has caused major changes in the straw surface, while the thermal analysis indicated that the sodium hydroxide caused variations in thermal stability of straw constituents. Water absorption measurements showed that treatments have accelerated the absorption process and the reduction of contact angle values for treated samples with solvents indicated higher hidrophilicity of straw. The tensile tests showed lower values of elastic modulus and tensile strength for treated samples. Furthermore, coatings using pure commercial resins A and B as well as the formulations with clay were applied in straw and they were examined once again through thermal analysis, water absorption measurements, contact angle and mechanical tests. To analyze the effect of heat ageing, samples were subjected to tensile tests again in order to assess its resistance. The results showed that the resins/clay formulations increased thermal stability of straw, they promoted a good impermeabilization and caused significant decrease in the values of elastic modulus and tensile strength. Evaluating the ageing effect on the mechanical properties, it has been showed good recovery to the coated straw with the formulations A 60 and A 80% in modulus and tensile strength values and elongation at break values have remained very close. It is thus concluded that the carnauba straw can be used as a coating of pipelines with significant cost savings, since there is no need for pretreatment for its use and shows itself as a viable biotechnology alternative, contributing to the quality of coatings material and environment preservation.

Estudo da digestão de sedimento de curtume visando a extração do cromo por microemulsão

Leather tanneries generate effluents with high content of heavy metals, especially chromium, which is used in the mineral tanning process. Microemulsions have been studied in the extraction of heavy metals from aqueous solutions. Considering the problems related with the sediment resulting from the tanning process, due to its high content in chromium, in this work this sediment was characterized and microemulsion systems were applied for chromium removal. The extraction process consists in the removal of heavy metal ions present in an aqueous feeding solution (acid digestion solution) by a microemulsion system. First three different solid sludge digestion methods were evaluated, being chosen the method with higher digestion capacity. For this digestion method, seeking its optimization, was evaluated the influence of granule size, temperature and digestion time. Experimental results showed that the method proposed by USEPA (Method A) was the most efficient one, being obtained 95.77% of sample digestion. Regarding to the evaluated parameters, the best results were achieved at 95°C, 14 Mesh granule size, and 60 minutes digestion time. For chromium removal, three microemulsion extraction methods were evaluated: Method 1, in a Winsor II region, using as aqueous phase the acid digestion solution; Method 2, in a Winsor IV region, being obtained by the addition of the acid digestion solution to a microemulsion phase, whose aqueous phase is distilled water, until the formation of Winsor II system; and Method 3, in a Winsor III region, consisting in the formation of a Winsor III region using as aqueous phase the acid digestion solution, diluted in NaOH 0.01N. Seeking to optimize the extraction process only Method 1 (Systems I, II, and VIII) and Method 2 (System IX) were evaluated, being chosen points inside the interest regions (studied domains) to study the influence of contact time and pH in the extraction percentiles. The studied systems present the following compositions: System I: Surfactant Saponified coconut oil, Cosurfactant 1-Butanol, Oil phase Kerosene, Aqueous phase 2% NaCl solution; System II: Aqueous phase Acid digestion solution with pH adjusted using KOH (pH 3.5); System VIII: Aqueous phase - Acid digestion solution (pH 0.06); and System IX Aqueous phase Distilled water (pH 10.24), the other phases of Systems II, VIII and IX are similar to System I. Method 2 showed to be the more efficient one regarding chromium extraction percentile (up to 96.59% - pH 3.5). Considering that with Method 2 the microemulsion region only appears in the Winsor II region, it was studied Method 3 (System X) for the evaluation and characterization of a triphasic system, seeking to compare with a biphases system. System X is composed by: Surfactant Saponified coconut oil, Cosurfactant 1-Butanol, Oil phase Kerosene, Aqueous phase Acid digestion solution diluted with water and with its pH adjusted using 0.01N NaOH solution. The biphasic and triphasic microemulsion systems were analyzed regarding its viscosity, extraction efficiency and drop effective diameter. The experimental results showed that for viscosity studies the obtained values were low for all studied systems, the diameter of the drop is smaller in the Winsor II region, with 15.5 nm, reaching 46.0 nm in Winsor III region, being this difference attributed to variations in system compositions and micelle geometry. In chromium extraction, these points showed similar results, being achieved 99.76% for Winsor II system and 99.62% for Winsor III system. Winsor III system showed to be more efficient due to the obtaining of a icroemulsion with smaller volume, with the possibility to recover the oil phase in excess, and the use of a smaller proportion of surfactant and cosurfactant (C/S)

Remoção de frações de óleo leve e pesado de rocha calcária através de sistemas microemulsionados

In this research the removal of light and heavy oil from disintegrated limestone was investigated with use of microemulsions. These chemical systems were composed by surfactant, cosurfactant, oil phase and aqueous phase. In the studied systems, three points in the water -rich microemulsion region of the phase diagrams were used in oil removal experiments. These microemulsion systems were characterized to evaluate the influence of particle size, surface tension, density and viscosity in micellar stability and to understand how the physical properties can influence the oil recovery process. The limestone rock sample was characterized by thermogravimetry, BET area, scanning electron microscopy and X-ray fluorescence. After preparation, the rock was placed in contact with light and heavy oil solutions to allow oil adsorption. The removal tests were performed to evaluate the influence of contact time (1 minute, 30 minutes, 60 minutes and 120 minutes), the concentration of active matter (20, 30 and 40 %), different cosurfactants and different oil phases. For the heavy oil, the best result was on SME 1, with 20 % of active matter, 1 minute of contact time, with efficiency of 93,33 %. For the light oil, also the SME 1, with 20 % of active matter, 120 minutes of contact time, with 62,38 % of efficiency. From the obtained results, it was possible to conclude that microemulsions can be considered as efficient chemical systems for oil removal from limestone formations

Aplicação de sabões de ácidos graxos epoxidados como inibidores de corrosão em oleoduto

Corrosion usually occurs in pipelines, so that it is necessary to develop new surface treatments to control it. Surfactants have played an outstanding role in this field due to its capacity of adsorbing on metal surfaces, resulting in interfaces with structures that protect the metal at low surfactant concentrations. The appearance of new surfactants is a contribution to the area, as they increase the possibility of corrosion control at specific conditions that a particular oil field presents. The aim of this work is to synthesize the surfactants sodium 12 hydroxyocadecenoate (SAR), sodium 9,10-epoxy-12 hydroxyocadecanoate (SEAR), and sodium 9,10:12,13-diepoxy-octadecanoate (SEAL) and apply them as corrosion inhibitors, studying their action in environments with different salinities and at different temperatures. The conditions used in this work were chosen in order to reproduce oil field reality. The study of the micellization of these surfactants in the liquid-gas interface was carried out using surface tensiometry. It was observed that cmc increased as salt concentration was increased, and temperature and pH were decreased, while cmc decreased with the addition of two epoxy groups in the molecule. Using the values of cmc and the Gibbs equation, the values of Gibbs free energy of adsorption, area per adsorbed molecule, and surface excess were calculated. The surface excess increases as salt concentration and temperature decreases, increasing as pH is increased. The area per adsorbed molecule and the free energy of adsorption decrease with salt concentration, temperature, and pH increase. SAXS results showed that the addition of epoxy group in surfactant structure results in a decrease in the repulsion between the micelles, favoring the formation of more oblong micellar structures, ensuring a better efficiency of metal coverage. The increase in salt and surfactant concentrations provides an increase in micellar diameter. It was shown that the increase in temperature does not influence micellar structure, indicating thermal stability that is advantageous for use as corrosion inhibitor. The results of inhibition efficiency for the surfactants SEAR and SEAL were considered the best ones. Above cmc, adsorption occurred by the migration of micelles from the bulk of the solution to the metal surface, while at concentrations below cmc film formation must be due to the adsorption of semi-micellar and monomeric structures, certainly due to the presence of the epoxy group, which allows side interactions of the molecule with the metal surface. The metal resistance to corrosion presented values of 90% of efficiency. The application of Langmuir and Frumkin isotherms showed that the later gives a better description of adsorption because the model takes into account side interactions from the adsorbing molecules. Wettability results showed that micelle formation on the solid surface occurs at concentrations in the magnitude of 10-3 M, which isthe value found in the cmc study. This value also justifies the maximum efficiencies obtained for the measurements of corrosion resistance at this concentration. The values of contact angle as a function of time suggest that adsorption increases with time, due to the formation of micellar structures on metal surface