Monitoring the process of densification of 3D and 4D (tridirectional and tetradirectional) carbon/carbon composites

Carbon fiber reinforced carbon composites can be made by iterative liquid impregnation or gas phase carbon deposition routes. In both cases, at the final processing stage the carbon fiber is embedded in carbon matrix which results in unique properties such as low density, high thermal conductivity and thermal shock resistance, low thermal expansion and high modulus, in relation to other refractory materials. In the present study assembled three-directional and four-directional preforms, having 50% volume of pores, were densified by iterative cycles of thermoset resin impregnation followed by pyrolysis under inert atmosphere, until appropriate densities were achieved. The thermoset resin is converted in a carbon matrix during pyrolysis. The iterative manufacturing process of the carbon fiber reinforced carbon composites is evaluated by means of nondestructive techniques based on X-ray computed tomography and electrical resistivity. X-ray computed tomography gives a general mapping view of the filling pores of the preforms which impacts results of the electrical resistivity. After six processing cycles and heat treatments up to 2000?, the final densities of the three-directional and four-directional carbon fiber reinforced carbon composites were 1.16g/cm(3) and an electrical resistivity of approximate to 0.07m. The configuration of preforms, three-directional or four-directional, did not alter the densification profile, in terms of increasing density and reducing porosity during the processing cycles.

Hygrotermal effects evaluation using the losipescu shear test for glare laminates

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dielectric behaviour of CaCu3Ti4O12-epoxy composites

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Foaming of EVA/starch blends: Characterization of the structure, physical properties, and biodegradability

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Natural rubber latex coated with calcium phosphate for biomedical application

Natural rubber latex (NRL) is a flexible biomembrane that possesses angiogenic properties and has recently been used for guided bone regeneration, enhancing healing without fibrous tissue, allergies or rejection. Calcium phosphate (Ca/P) ceramics have chemical, biological, and mechanical properties similar to mineral phase of bone, and ability to bond to the host tissue, although it can disperse from where it is applied. Therefore, to create a composite that could enhance the properties of both materials, NRL biomembranes were coated with Ca/P. NRL biomembranes were soaked in 1.5 times concentrated SBF solution for seven days, avoiding the use of high temperatures. SEM showed that Ca/P has been coated in NRL biomembrane, XRD showed low crystallinity and FTIR showed that is the carbonated type B. Furthermore, hemolysis of erythrocytes, quantified spectrophotometrically using materials (Ca/P, NRL, and NRL + Ca/P) showed no hemolytic effects up to 0.125 mg/mL (compounds and mixtures), indicating no detectable disturbance of the red blood cell membranes. The results show that the biomimetic is an appropriate method to coat NRL with Ca/P without using high temperatures, aiming a new biomembrane to improve guided bone regeneration.

Atividade toxicogenética de corantes usados na formulação da tintura capilar preta, individuais e em associação, por meio de diferentes ensaios biológicos

Pós-graduação em Ciências Biológicas (Biologia Celular e Molecular) - IBRC

Uprecycling leater waste

Incorporating contaminated leather waste into natural rubber improves the rubber's mechanical properties and avoids improper disposal of toxins.

Desenvolvimento de sensor baseado em polímeros molecularmente impressos para determinação de álcoois superiores em óleo fúsel

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da viabilidade de produção da peça alimentação/ladrão para banheiras

The product development field daily works in the chase of new materials and technologies that fulfills the requirements of the consumer market. So, projects are developed in order to theoretically predict what will actually happen. The production of household appliance is not different. To provide a pleasant bath to the costumer, the manufacture of a bathtub counts on many components. With this in mind, this work goal is to study the possibility of production by plastic injection of the assembly water source/overflow pipe used in bathtubs and compare its production cost with the cost of the assembly acquired from third parties. The injection process is widely used on the world stage because of its numerous advantages, however, due to the high cost of the molds, it is important to estimate the time required for the return of the initial investment. To do this, a model was designed to examine its dimensions and then initiate the study of the possibility to inject the components with the available injection machine and the production cycle. With the results, it was found that there was a reduction in the cost of the finished assembly, but a very long time to return the initial investment due to the current financial scenery of the country

Comparison of the Fuel Needed to Transport Plastic Recyclables Verses Aluminum Recyclables from Yellowstone National Park

Research has provided no definitive answers on whether PET plastic bottles or aluminum cans are a more environmentally sustainable choice as soda containers. This paper researches the fuel used in recycling each of these materials from Yellowstone National Park to processing locations. The data is used to determine which of these alternatives use less fuel in this process. It was found that plastics use more fuel when transported from Yellowstone National Park to the processing center. Aluminum uses less fuel per ton to transport from Yellowstone to the processing center. The conclusions from this research may have implications on which material would be advised to use in selling soda in Yellowstone National Park.

Estudo da viabilidade de produção da peça alimentação/ladrão para banheiras

The product development field daily works in the chase of new materials and technologies that fulfills the requirements of the consumer market. So, projects are developed in order to theoretically predict what will actually happen. The production of household appliance is not different. To provide a pleasant bath to the costumer, the manufacture of a bathtub counts on many components. With this in mind, this work goal is to study the possibility of production by plastic injection of the assembly water source/overflow pipe used in bathtubs and compare its production cost with the cost of the assembly acquired from third parties. The injection process is widely used on the world stage because of its numerous advantages, however, due to the high cost of the molds, it is important to estimate the time required for the return of the initial investment. To do this, a model was designed to examine its dimensions and then initiate the study of the possibility to inject the components with the available injection machine and the production cycle. With the results, it was found that there was a reduction in the cost of the finished assembly, but a very long time to return the initial investment due to the current financial scenery of the country

Production and characterization of poly-(3-hydroxybutyrate) from recombinant Escherichia coli grown on cheap renewable carbon substrates

Although the biopolymer poly-(3-hydroxybutyrate), P[3HB], presents physicochemical properties that make it an alternative material to conventional plastics, its biotechnological production is quite expensive. As carbon substrates contribute greatly to P[3HB] production cost, the utilization of a cheaper carbon substrate and less demanding micro-organisms should decrease its cost. In the present study a 23 factorial experimental design was applied, aiming to evaluate the effects of using hydrolysed corn starch (HCS) and soybean oil (SBO) as carbon substrates, and cheese whey (CW) supplementation in the mineral medium (MM) on the responses, cell dried weigh (DCW), percentage P[3HB] and mass P[3HB] by recombinant Escherichia coli strains JM101 and DH10B, containing the P[3HB] synthase genes from Cupriavidus necator (ex-Ralstonia eutropha). The analysis of effects indicated that the substrates and the supplement and their interactions had positive effect on CDW. Statistically generated equations showed that, at the highest concentrations of HCS, SO and CW, theoretically it should be possible to produce about 2 g L(1) DCW, accumulating 50% P[3HB], in both strains. To complement this study, the strain that presented the best results was cultivated in MM added to HCS, SBO and CW ( in best composition observed) and complex medium (CM) to compare the obtained P[3HB] in terms of physicochemical parameters. The obtained results showed that the P[3HB] production in MM (1.29 g L(-1)) was approximately 20% lower than in CM (1.63 g L(-1)); however, this difference can be compensated by the lower cost of the MM achieved by the use of cheap renewable carbon sources. Moreover, using differential scanning calorimetry and thermogravimetry analyses, it was observed that the polymer produced in MM was the one which presented physicochemical properties (Tg and Tf) that were more similar to those found in the literature for P[3HB].

Experimental analyses of the poly(vinyl chloride) foams' mechanical anisotropic behavior

Assessing a full set of mechanical properties is a rather complicate task in the case of foams, especially if material models must be calibrated with these results. Many issues, for example anisotropy and heterogeneity, influence the mechanical behavior. This article shows through experimental analyses how the microstructure affects different experimental setups and it also quantifies the degree of anisotropy of a poly(vinyl chloride) foam. Monotonic and cyclic experimental tests were carried out using standard compression specimens and non-standard tensile specimens. Results are complemented and compared with the aid of a digital image correlation technique and scanning electron microscopy analyses. Mechanical properties (e.g., elastic and plastic Poisson's ratios) are evaluated for compression and tensile tests, for two different material directions (normal and in-plane). The material is found to be transversely isotropic. Differences in the results of the mechanical properties can be as high as 100%, or even more depending on the technique used and the loading direction. Also, the experimental analyses show how the material's microstructure behavior, like the evolution of the herein identified yield fronts and a spring back phenomenon, can influence the phenomenological response and the failure mechanisms as well as the hardening curves. POLYM. ENG. SCI., 52:2654-2663, 2012. (C) 2012 Society of Plastics Engineers

COMMON GOOSE BARNACLES LEPAS AUSTRALIS (THORACICA, PEDUNCULATA) ON DECEASED MAGELLANIC PENGUINS SPHENISCUS MAGELLANICUS (AVES)

Fundacao de Amparo a Pesquisa do Estado de Sao Paulo (FAPESP)

Assessment of cumulative damage by using ultrasonic C-scan on carbon fiber/epoxy composites under thermal cycling

In recent years, structural composites manufactured by carbon fiber/epoxy laminates have been employed in large scale in aircraft industries. These structures require high strength under severe temperature changes of -56° until 80 °C. Regarding this scenario, the aim of this research was to reproduce thermal stress in the laminate plate developed by temperature changes and tracking possible cumulative damages on the laminate using ultrasonic C-scan inspection. The evaluation was based on attenuation signals and the C-scan map of the composite plate. The carbon fiber/epoxy plain weave laminate underwent temperatures of -60° to 80 °C, kept during 10 minutes and repeated for 1000, 2000, 3000 and 4000 times. After 1000 cycles, the specimens were inspected by C-scanning. A few changes in the laminate were observed using the inspection methodology only in specimens cycled 3000 times, or so. According to the found results, the used temperature range did not present enough conditions to cumulative damage in this type of laminate, which is in agreement with the macro - and micromechanical theory.