Thermal performance of multipass parallel and counter-cross-flow heat exchangers

A thorough study of the thermal performance of multipass parallel cross-flow and counter-cross-flow heat exchangers has been carried out by applying a new numerical procedure. According to this procedure, the heat exchanger is discretized into small elements following the tube-side fluid circuits. Each element is itself a one-pass mixed-unmixed cross-flow heat exchanger. Simulated results have been validated through comparisons to results from analytical solutions for one- to four-pass, parallel cross-flow and counter-cross-flow arrangements. Very accurate results have been obtained over wide ranges of NTU (number of transfer units) and C* (heat capacity rate ratio) values. New effectiveness data for the aforementioned configurations and a higher number of tube passes is presented along with data for a complex flow configuration proposed elsewhere. The proposed procedure constitutes a useful research tool both for theoretical and experimental studies of cross-flow heat exchangers thermal performance.

Nanopore size growth and ultrafiltration performance of SnO2 ceramic membranes prepared by sol-gel route

Supported ceramic membranes have been produced by the sol-casting procedure from aqueous colloidal suspensions prepared by the sol-gel route. Coatings on a tubular alumina support have been successfully performed leading to crack free layers. Samples have been sintered at 400, 500 and 600 degreesC, and the effect of heating treatment on the nanostructure and on the ultrafiltration properties are analyzed. The characterization has been done by high resolution scanning electron microscopy, nitrogen adsorption-desorption isotherms, water permeation and cut-off determination using polyethylene glycol standard solutions. The micrographs have revealed that grains and pore size increase with the temperature, whereas their shape remains invariant. This results is in agreements with N-2 adsorption-desorption analyses, which have revealed that the mean pore size diameter increases from 4 to 10 nm as the sintering temperature increases from 400 to 600 degreesC, while the total porosity remains constant. Furthermore, the tortuosity, calculated from water permeability, is essentially invariant with the sintering temperatures. The membranes cut-off, determined with a retention rate equal to 95%, are 3500, 6500 and 9000 g . mol(-1) for 400, 500 and 600 degreesC, respectively, showing that the permeation properties of SnO2 ultrafiltration membranes can easily be controlled by sintering condition.

Overview on the performance of Brazilian broilers (1990 to 2009)

This article describes the genetic evolution of commercial broilers between 1990 and 2009, considering live performance, in particular, in terms of weight gain and feed conversion ratio. In order to determine if the assumption that the relationship between body weight gain and feed conversion ratio is increasing and positive, information on all broiler strains reared in Brazil were collected from several companies present in five Brazilian regions. This survey aimed at evaluating broiler live performance as a function of genetic improvement with time. Broiler performance improved, as shown by the statistical differences obtained for the following parameters: livability, live weight, daily weight gain, feed conversion ratio, and production efficiency index between 1990 and 2009. However, live weight gain and feed conversion ratio are emphasized due to the significant differences found along the studied period.

Performance of a reciprocal shaker in mechanical dispersion of soil samples for particle-size analysis

A dispersão da amostra de solo é uma etapa fundamental da análise granulométrica, sendo realizada mediante o uso de dispersantes químicos e agitação mecânica. O objetivo deste trabalho foi avaliar a eficiência de mesa agitadora reciprocante de baixa rotação na dispersão mecânica de amostras de solos de diferentes classes texturais. Foram realizadas análises granulométricas em 61 amostras com quatro repetições, empregando o método da pipeta para determinação da fração argila e tamisagem para determinação das frações areia grossa, areia fina e areia total, sendo o silte determinado por diferença. Na avaliação de desempenho, os resultados obtidos com uso da mesa agitadora reciprocante (MAR) foram comparados com dados disponíveis para as mesmas amostras oriundos de relatórios do Ensaio de Proficiência IAC para Laboratórios de Análises de Solos - Prolab/IAC. Análises de acurácia foram realizadas com base nos valores dos intervalos de confiança definidos para cada fração granulométrica componente de cada amostra ensaiada. Indicadores gráficos também foram utilizados na comparação de dados, por meio de dispersão e ajuste linear. A estatística descritiva indicou preponderância de baixa variabilidade em mais de 90 % dos resultados obtidos para as amostras de texturas arenosa, média e argilosa e em 68 % dos obtidos para as amostras de textura muito argilosa, indicando boa repetibilidade dos resultados obtidos com a MAR. Média variabilidade foi mais frequentemente associada à fração silte, seguida da fração areia fina. Os resultados das análises de sensibilidade indicam acurácia de 100 % nas três frações granulométricas - areia total, silte e argila - para todas as amostras analisadas pertencentes às classes texturais muito argilosa, argilosa e média. Para as nove amostras de textura arenosa, a acurácia média foi de 85,2 %, e os maiores desvios ocorreram em relação à fração silte. Nas aproximações lineares, coeficientes de correlação igual (silte) ou superiores (areia total e argila) a 0,93, bem como diferenças menores do que 0,16 entre os coeficientes angulares das retas e o valor unitário, indicam alta correlação entre os resultados de referência (Prolab/IAC) e os obtidos nos ensaios com a MAR. Conclui-se pelo desempenho satisfatório da mesa agitadora reciprocante de baixa rotação para dispersão mecânica de amostras de solo de diferentes classes texturais para fins de análise granulométrica, permitindo recomendar o uso alternativo do equipamento quando se emprega agitação lenta. As vantagens do uso do equipamento nacional incluem o baixo custo, a possibilidade de análise simultânea de grande número de amostras e o uso de frascos comuns, de vidro ou de plástico, baratos e de fácil reposição.

Simulation of the energy performance of maize production integrated to pig farming

Foi avaliado o desempenho energético da suinocultura integrada à produção de milho em grão em sistema de plantio direto mecanizado. Nesta concepção de integração proposta, os dejetos suínos são utilizados como fertilizantes na produção de milho. O sistema foi delimitado envolvendo as atividades associadas ao manejo dos suínos e de produção do milho (manejo do solo, cultivo e colheita). O período de análise considerado foi de um ano, o que possibilita a produção de três lotes de suínos e duas safras de milho. Para avaliar o desempenho energético, foram criados três indicadores: eficiência energética, eficiência de uso de fontes não renováveis e o custo de energia não renovável para a produção de proteína. As entradas energéticas são compostas pelos insumos e pela infraestrutura, utilizados na criação dos suínos e na produção de milho, e pela radiação solar incidente no agrossistema. Já as saídas são representadas pelos seus produtos (suínos terminados e o milho). Os resultados obtidos nas simulações apontam que a integração melhora o desempenho energético das granjas suinícolas, aumentando a eficiência energética (186%) e a eficiência não renovável (352%), além de reduzir o custo de energia não renovável para a produção de proteína (‑58%).

Performance of UASB reactors in two stages under different HRT and OLR treating residual waters of swine farming

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Residual feed intake and relationships with performance of Nellore cattle selected for post weaning weight

Objetivou-se com este trabalho avaliar desempenho, parâmetros de eficiência e correlações fenotípicas entre medidas de eficiência energética de animais Nelore selecionados para peso pós-desmame e classificados quanto ao consumo alimentar residual, calculado pela diferença entre o consumo observado e o predito, com base no peso vivo médio metabólico e no ganho médio diário. Assim, os animais foram classificados em três grupos: alto (> média + 0,5 desvio-padrão; menos eficientes); médio (± 0,5 desvio-padrão da média); e baixo (< média - 0,5 desvio padrão; mais eficientes) consumo alimentar residual. Não foram observadas diferenças nos pesos vivos inicial e final, no ganho médio diário e no consumo de matéria seca entre os grupos. Animais com baixo consumo alimentar residual mostraram-se também com melhor eficiência alimentar, conversão alimentar e eficiência parcial de crescimento e não apresentaram diferenças em relação aos outros grupos quanto à taxa de crescimento relativo e taxa Kleiber. O consumo alimentar residual apresentou correlação significativa com eficiência alimentar (_0,25), conversão alimentar (0,25), eficiência parcial de crescimento (_0,37) e consumo de MS (0,16) e não apresentou correlação significativa com peso vivo (0,04), ganho médio diário (_0,02), taxa de crescimento relativo (_0,03) e taxa de Kleiber (_0,05). Foram encontradas correlações significativas entre conversão alimentar e peso vivo inicial (0,34) e ganho médio diário (_0,46). Eficiência parcial de crescimento apresentou correlação significativa comtodos os outros parâmetros de eficiência analisados. O consumo alimentar residual, em comparação às demais medidas de eficiência energética, apresenta grande potencial na eficiência produtiva, sendo independente de crescimento e tamanho dos animais.

Ingestive behavior and performance of female lambs grazing on Marandu palisadegrass under different stocking rates

The ingestive behavior and performance of female lambs grazing on Marandu pasture submitted to different stocking rates during the rainy and transition season were evaluated. The experimental area with 4,500 m² was divided into 45 paddocks of 100 m². Twenty-seven Santa Ines female lambs (purebred) with 4 months age and 22 kg of initial body weight were distributed in a completely randomized design, with nine replicates. Lambs were divided into 9 groups with the same initial weight and submitted to three stocking rates: 2, 3 and 4 lambs/paddock, which corresponded to 40, 60 and 80 lambs/ha, respectively. Each group of animals had a module of five paddocks, managed on intermittent grazing system, with 7 days of occupation and 28 d of rest. Increase on time grazing and reduction on time ruminating and resting were observed as stocking rates increased. There was 14% raise in time grazing and 41% decline on time resting by lambs subjected to the highest stocking rate compared with those in the lower stocking rate. The number of animals/ha promoted linear effect on average daily gain, which was higher for animals in the lowest stocking rate of 90 g/d. For gain per area, the best result was obtained with 60 animals/ha featuring an average value of 426 kg/ha.

Performance of Nellore young bulls on Marandu grass pasture with protein supplementation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of whole toasted and extruded soybean on the performance of broilers

This experiment was conducted to compare the performance of 1260 chicks fed diets containing soybean meal plus soybean oil (SBM + oil), whole extruded soybean (ESB) and whole steam toasted soybean (TSB), with two protein levels. A complete randomized design was used, with six treatments and 3 replicates of each sex. The treatments consisted of a factorial arrangement 2 x 3 x 2 to test three soybean types (SBM + oil, ESB and TSB), two protein levels (optimum and suboptimum) and two sexes. From 1 to 49 days of age, the tested soybean types did not affect the diet intake. However, ESB provided higher weight gain in relation to SBM + oil, but it did not differ from TSB. The feed:gain ratio obtained with ESB and TSB was better in relation to SBM + oil. There was no difference between the nutritional value of TSB and ESB, because they provided similar performance to the birds.

Diurnal variation in oral temperature, sleepiness and performance of high school girls

Evaluation of rhythmic fluctuations cf physical and mental variables should be of special significance for the understanding of students' performance and setting the schedules of school activities. The present study investigated the pattern of diurnal variation in oral temperature, sleepiness and performance of a group of adolescents undergoing a daytime school schedule. Eighteen girls (mean age 16 years-old), who attended the same class from 0715h to 1645h, were tested on seven days. They measured their oral temperature, quantified their sleepiness level by means of a visual analogue scale, and completed the following tests: letter cancellation test, addition test, and a simple motor task. One-way ANOVA statistics for repeated measures was used in order to verify the effect of test time on oral temperature,sleepiness and performance. Possible correlations between the level of sleepiness and performance were investigated by means of Spearman rank correlation. The results revealed significant time of day effect cn all variables, except for the number of addition errors. Oral temperature values showed an increase from morning to afternoon. Letter cancellation, motor task and addition scores increased from early morning to late afternoon, showing rapid fluctuations throughout the day. Sleepiness level was negatively correlated with letter cancellation scores during the first three tests of the day. In agreement with other work, the diurnal variation of oral temperature, letter cancellation and addition test showed an improvement as the day progressed. Sleepiness, on the other hand, decreased throughout the day, with the highest level associated with the first test of the day, suggesting a circadian pattern of variation rather than a cumulative effect due to school activities.

Clinical performance of a self-etching adhesive at 18 months

Purpose: To test the null hypothesis that beveling and/or etching enamel would not affect the 18-month clinical performance of the self-etching adhesive Clearfil SE Bond (CSEB) in noncarious cervical lesions (NCCL). Methods: With Institutional Review Board approval, 34 patients were enrolled in this study. A total of 120 NCCL was selected and assigned to four groups: (1) CSEB was applied without any cavity preparation; (2) CSEB was applied after beveling enamel; (3) CSEB was applied after etching enamel for 15 seconds with 35% phosphoric acid; (4) CSEB was applied after beveling and etching enamel. A microfilled composite resin was used for all restorations. Resuts: At 6 months after initial placement, 120 restorations (a 100% recall rate) were evaluated. At 18 months, 87 restorations (a 72.5% recall rate) were available for evaluation. A survival rate of 100% was measured for all groups at both 6 and 18 months. Sensitivity to air decreased significantly only for Group 3 (no bevel+acid etch) from baseline to 18 months without statistical changes from 6 months to 18 months. None of the other parameters resulted in significant differences for any of the four groups. However, when data were pooled, both the overall marginal discoloration and the overall marginal adaptation were significantly worse at 18 months than at baseline, while sensitivity to air decreased significantly from baseline to 18 months. The 18-month survival rate of the self-etching adhesive Clearfil SE Bond was not improved by enamel bevel or by enamel etching. Both overall marginal adaptation and overall marginal discoloration were worse at 18 months than at baseline.

Coating residual stress effects on fatigue performance of 7050-T7451 aluminum alloy

The tendency of the aircraft industry is to enhance customer value by improving performance and reducing environmental impact. In view of availability, aluminum alloys have a historically tendency to faster insertion due to their lower manufacturing and operated production infrastructure. In landing gear components, wear and corrosion control of many components is accomplished by surface treatments of chrome electroplating on steel or anodizing of aluminum. One of the most interesting environmentally safer and cleaner alternatives for the replacement of hard chrome plating or anodizing is tungsten carbide thermal spray coating, applied by the high velocity oxy fuel (HVOF) process. However, it was observed that residual stresses originating from these coatings reduce the fatigue strength of a component.An effective process as shot peening treatment, considered to improve the fatigue strength, pushes the crack sources beneath the surface in most of medium and high cycle cases, due to the compressive residual stress field induced. The objective of this research is to evaluate a tungsten carbide cobalt (WC-Co) coating applied by the high velocity oxy fuel (HVOF) process, used to replace anodizing. Anodic films were grown on 7050-T7451 aluminum alloy by sulfuric acid anodizing, chromic acid anodizing and hard anodizing. The influence on axial fatigue strength of anodic films grown on the aluminum alloy surface is to degrade the stress-life performance of the base material. Three groups of specimens were prepared and tested in axial fatigue to obtain S-N curves: base material, base material coated by HVOF and base material shot peened and coated.Experimental results revealed increase in the fatigue strength of Al 7050-T7451 alloy associated with the WC 17% Co coating. on the other hand, a reduction in fatigue life occurred in the shot peened and coated condition. Scanning electron microscopy technique and optical microscopy were used to observe crack origin sites, thickness and coating/substrate adhesion. (c) 2007 Elsevier B.V. All rights reserved.