Lithography-free micro- and nanostructuring based on conventional plasma etching

In now-a-days semiconductor and MEMS technologies the photolithography is the working horse for fabrication of functional devices. The conventional way (so called Top-Down approach) of microstructuring starts with photolithography, followed by patterning the structures using etching, especially dry etching. The requirements for smaller and hence faster devices lead to decrease of the feature size to the range of several nanometers. However, the production of devices in this scale range needs photolithography equipment, which must overcome the diffraction limit. Therefore, new photolithography techniques have been recently developed, but they are rather expensive and restricted to plane surfaces. Recently a new route has been presented - so-called Bottom-Up approach - where from a single atom or a molecule it is possible to obtain functional devices. This creates new field - Nanotechnology - where one speaks about structures with dimensions 1 - 100 nm, and which has the possibility to replace the conventional photolithography concerning its integral part - the self-assembly. However, this technique requires additional and special equipment and therefore is not yet widely applicable. This work presents a general scheme for the fabrication of silicon and silicon dioxide structures with lateral dimensions of less than 100 nm that avoids high-resolution photolithography processes. For the self-aligned formation of extremely small openings in silicon dioxide layers at in depth sharpened surface structures, the angle dependent etching rate distribution of silicon dioxide against plasma etching with a fluorocarbon gas (CHF3) was exploited. Subsequent anisotropic plasma etching of the silicon substrate material through the perforated silicon dioxide masking layer results in high aspect ratio trenches of approximately the same lateral dimensions. The latter can be reduced and precisely adjusted between 0 and 200 nm by thermal oxidation of the silicon structures owing to the volume expansion of silicon during the oxidation. On the basis of this a technology for the fabrication of SNOM calibration standards is presented. Additionally so-formed trenches were used as a template for CVD deposition of diamond resulting in high aspect ratio diamond knife. A lithography-free method for production of periodic and nonperiodic surface structures using the angular dependence of the etching rate is also presented. It combines the self-assembly of masking particles with the conventional plasma etching techniques known from microelectromechanical system technology. The method is generally applicable to bulk as well as layered materials. In this work, layers of glass spheres of different diameters were assembled on the sample surface forming a mask against plasma etching. Silicon surface structures with periodicity of 500 nm and feature dimensions of 20 nm were produced in this way. Thermal oxidation of the so structured silicon substrate offers the capability to vary the fill factor of the periodic structure owing to the volume expansion during oxidation but also to define silicon dioxide surface structures by selective plasma etching. Similar structures can be simply obtained by structuring silicon dioxide layers on silicon. The method offers a simple route for bridging the Nano- and Microtechnology and moreover, an uncomplicated way for photonic crystal fabrication.

Optical Characterization of Organic Gain Materials for UV-emitting Hybrid Complex Coupled VCSELs

In this thesis, optical gain measurement setup based on variable stripe length method is designed, implemented and improved. The setup is characterized using inorganic and organic samples. The optical gain of spiro-quaterphenyl is calculated and compared with measurements from the setup. Films with various thicknesses of spiro-quaterphenyl, methoxy-spiro-quaterphenyl and phenoxy-spiro-quaterphenyl are deposited by a vacuum vapor deposition technique forming asymmetric slab waveguides. The optical properties, laser emission threshold, optical gain and loss coefficient for these films are measured. Additionally, the photodegradation during pumping process is investigated.

Punching Shear Behavior of UHPC Flat Slabs

At the Institute of Structural Engineering of the Faculty of Civil Engineering, Kassel University, series tests of slab-column connection were carried out, subjected to concentrated punching load. The effects of steel fiber content, concrete compressive strength, tension reinforcement ratio, size effect, and yield stress of tension reinforcement were studied by testing a total of six UHPC slabs and one normal strength concrete slab. Based on experimental results; all the tested slabs failed in punching shear as a type of failure, except the UHPC slab without steel fiber which failed due to splitting of concrete cover. The post ultimate load-deformation behavior of UHPC slabs subjected to punching load shows harmonic behavior of three stages; first, drop of load-deflection curve after reaching maximum load, second, resistance of both steel fibers and tension reinforcement, and third, pure tension reinforcement resistance. The first shear crack of UHPC slabs starts to open at a load higher than that of normal strength concrete slabs. Typically, the diameter of the punching cone for UHPC slabs on the tension surface is larger than that of NSC slabs and the location of critical shear crack is far away from the face of the column. The angle of punching cone for NSC slabs is larger than that of UHPC slabs. For UHPC slabs, the critical perimeter is proposed and located at 2.5d from the face of the column. The final shape of the punching cone is completed after the tension reinforcement starts to yield and the column stub starts to penetrate through the slab. A numerical model using Finite Element Analysis (FEA) for UHPC slabs is presented. Also some variables effect on punching shear is demonstrated by a parametric study. A design equation for UHPC slabs under punching load is presented and shown to be applicable for a wide range of parametric variations; in the ranges between 40 mm to 300 mm in slab thickness, 0.1 % to 2.9 % in tension reinforcement ratio, 150 MPa to 250 MPa in compressive strength of concrete and 0.1 % to 2 % steel fiber content. The proposed design equation of UHPC slabs is modified to include HSC and NSC slabs without steel fiber, and it is checked with the test results from earlier researches.

Apendicitis aguda perforada en adultos; aproximación a las inequidades sociales en salud, Bogotá 2012

La perforación del apéndice es una complicación temprana de la apendicitis aguda, demoras en el diagnóstico o tratamiento incrementan la tasa de perforación. Se desconoce si la perforación dl apéndice es un reflejo de inequidades sociales. Se pretendió determinar la asociación de la apendicitis aguda perforada en adultos y la equidad en acceso a salud. Estudio tipo cohorte retrospectivo documental, de historias clínicas de pacientes con apendicitis aguda; el análisis se realizó con Stata 11.1 y Epi-info. Los resultados se presentaron en tablas y figuras. Se incluyeron 540 casos (292 hombre y 248 mujeres), el grupo de edad que aporto más datos fue el de 18 a 49 años (391 pacientes); el tiempo medio de síntomas a consulta fue de 37,45 horas, y de 5,3 horas para el paso a cirugía desde el ingreso, fueron solicitadas 76 ecografías y 53 tomografías, 50 interconsultas a urología y 10 a ginecología hasta el diagnostico. El grupo de mayores de 49 años, el estrato socioeconómico tres y la tomografía fueron factores de riesgo independientes para perforación del apéndice. El análisis multivariado mostró asociación lineal entre el estrato socioeconómico y tiempo de síntomas al ingreso, tiempo para paso a cirugía, solicitud de ayudas diagnósticas e interconsultas, con buena significación estadística. La apendicitis aguda perforada en adultos, podría ser un indicador de inequidad en salud. Se requiere de estudios multi-céntricos, con mayor tiempo de evaluación y muestra para demostrar si el apéndice perforado es un trazador de inequidades en salud en Colombia.

Análisis de la calidad en la atención del paciente de cirugía general de urgencia

Objetivo: proponer un instrumento para el seguimiento de la calidad de la atención de pacientes con patologías quirúrgicas abdominales urgentes. Métodos: se revisaron restropectivamente historias clínicas de pacientes quienes requirieron cirugía general de urgencia (CGU) en agosto de 2013. Se analizaron variables demográficas, factores de riesgo, severidad y desenlace hasta el día 30 postoperatorio. Se incluyeron los indicadores de calidad del National Surgical Quality Improvement Program (NSQIP) y el National Trauma Data Bank, y se adicionaron otros. Resultados: Se intervinieron 231 pacientes de 261 procedimientos de CGU. La edad promedio fue 49 años. Los procedimientos más comunes fueron la colecistectomía laparoscópica (37.2%), la apendicectomía (35.6%), la laparotomía exploratoria (12.6%), el drenaje de colección abdominal (9.1%) y la liberación de adherencias (6.9%). La mortalidad fue de 3.46% (n=8), la morbilidad severa fue de 8.04%. La duración de la hospitalización fue de 6.54 días +/- 5.180 y la de hospitalización en Unidad de Cuidado Intensivo fue de 5.7 días +/- 4.42. La oportunidad de salas de cirugía para la apendicetomía fue de 5 horas para las apendicitis con peritonitis generalizada, y de 8 horas para las apendicitis localizadas, 37 horas para colecistitis, 7.48 horas para colangitis y 2.42 horas para diverticulitis. Conclusiones: Crear de un instrumento para la medición de la calidad de la atención de los pacientes en CGU, es necesario para la autoevaluación institucional y para definir planes de mejoramiento y distribución de los recursos.

Utilidad de la resonancia magnética en el diagnóstico de apendicitis aguda

Comparar el resultado de la resonancia magnética en el diagnóstico de apendicitis aguda con el patrón de oro (estudio histopatológico o seguimiento clínico del paciente) con el fin de establecer la utilidad de ésta como prueba diagnóstica y poder incluirla dentro del algoritmo de estudio de esta patología cuando hay sospecha clínica y un resultado negativo o dudoso de la ecografía abdominal

Conical sedimentary structures, trace fossils or not? Observations, experiments, and review

Conical sedimentary structures are widespread in the geological column. Those that are mediated by organisms (or organic matter) can be attributed to seven principal processes, which are investigated by experiment and/or field observations: (1) sand collapse into a cavity (decomposed body, open shaft, or gallery), (2) upward (escape) or downward locomotion by an organism through the sediment, (3) upward adjustment (equilibration), (4) casting of coelenterates' excavations, (5) organism-mediated soft-sediment deformation in heterolithic sediment, (6) biodeformational small and large excavations by organisms, and (7) fluid (gas or liquid) escape structures. Footprint loading may also be included. Criteria are given to distinguish between these processes. Dewatering pipes are best recognized by a zone of deformed and fluidized sediment at the base, and association with non-life (lethal) facies. Care must be used in assigning specimens to ichnotaxa, and it is generally necessary to slab, and also to carry out stratinomic investigation in the field.

Magnitude of climate variability during middle Pliocene warmth: a palaeoclimate modelling study

The nature and magnitude of climatic variability during the period of middle Pliocene warmth (ca 3.29–2.97 Ma) is poorly understood. We present a suite of palaeoclimate modelling experiments incorporating an advanced atmospheric general circulation model (GCM), coupled to a Q-flux ocean model for 3.29, 3.12 and 2.97 Ma BP. Astronomical solutions for the periods in question were derived from the Berger and Loutre BL2 astronomical solution. Boundary conditions, excluding sea surface temperatures (SSTs) which were predicted by the slab-ocean model, were provided from the USGS PRISM2 2°×2° digital data set. The model results indicate that little annual variation (0.5°C) in SSTs, relative to a ‘control’ experiment, occurred during the middle Pliocene in response to the altered orbital configurations. Annual surface air temperatures also displayed little variation. Seasonally, surface air temperatures displayed a trend of cooler temperatures during December, January and February, and warmer temperatures during June, July and August. This pattern is consistent with altered seasonality resulting from the prescribed orbital configurations. Precipitation changes follow the seasonal trend observed for surface air temperature. Compared to present-day, surface wind strength and wind stress over the North Atlantic, North Pacific and Southern Ocean remained greater in each of the Pliocene experiments. This suggests that wind-driven gyral circulation may have been consistently greater during the middle Pliocene. The trend of climatic variability predicted by the GCM for the middle Pliocene accords with geological data. However, it is unclear if the model correctly simulates the magnitude of the variation. This uncertainty is derived from, (a) the relative insensitivity of the GCM to perturbation in the imposed boundary conditions, (b) a lack of detailed time series data concerning changes to terrestrial ice cover and greenhouse gas concentrations for the middle Pliocene and (c) difficulties in representing the effects of ‘climatic history’ in snap-shot GCM experiments.

Monte Carlo phase diagram for diblock copolymer melts

A partial phase diagram is constructed for diblock copolymer melts using lattice-based Monte Carlo simulations. This is done by locating the order-disorder transition (ODT) with the aid of a recently proposed order parameter and identifying the ordered phase over a wide range of copolymer compositions (0.2 <= f <= 0.8). Consistent with experiments, the disordered phase is found to exhibit direct first-order transitions to each of the ordered morphologies. This includes the spontaneous formation of a perforated-lamellar phase, which presumably forms in place of the gyroid morphology due to finite-size and/or nonequilibrium effects. Also included in our study is a detailed examination of disordered cylinder-forming (f=0.3) diblock copolymers, revealing a substantial degree of pretransitional chain stretching and short-range order that set in well before the ODT, as observed previously in analogous studies on lamellar-forming (f=0.5) molecules. (c) 2006 American Institute of Physics.

Changes in the global sulfate burden due to perturbations in global CO2 concentrations

A large ensemble of general circulation model (GCM) integrations coupled to a fully interactive sulfur cycle scheme were run on the climateprediction.net platform to investigate the uncertainty in the climate response to sulfate aerosol and carbon dioxide (CO2) forcing. The sulfate burden within the model (and the atmosphere) depends on the balance between formation processes and deposition (wet and dry). The wet removal processes for sulfate aerosol are much faster than dry removal and so any changes in atmospheric circulation, cloud cover, and precipitation will feed back on the sulfate burden. When CO2 is doubled in the Hadley Centre Slab Ocean Model (HadSM3), global mean precipitation increased by 5%; however, the global mean sulfate burden increased by 10%. Despite the global mean increase in precipitation, there were large areas of the model showing decreases in precipitation (and cloud cover) in the Northern Hemisphere during June–August, which reduced wet deposition and allowed the sulfate burden to increase. Further experiments were also undertaken with and without doubling CO2 while including a future anthropogenic sulfur emissions scenario. Doubling CO2 further enhanced the increases in sulfate burden associated with increased anthropogenic sulfur emissions as observed in the doubled CO2-only experiment. The implications are that the climate response to doubling CO2 can influence the amount of sulfate within the atmosphere and, despite increases in global mean precipitation, may act to increase it.

Monte Carlo phase diagram for diblock copolymer melts

The phase diagram for diblock copolymer melts is evaluated from lattice-based Monte Carlo simulations using parallel tempering, improving upon earlier simulations that used sequential temperature scans. This new approach locates the order-disorder transition (ODT) far more accurately by the occurrence of a sharp spike in the heat capacity. The present study also performs a more thorough investigation of finite-size effects, which reveals that the gyroid (G) morphology spontaneously forms in place of the perforated-lamellar (PL) phase identified in the earlier study. Nevertheless, there still remains a small region where the PL phase appears to be stable. Interestingly, the lamellar (L) phase next to this region exhibits a small population of transient perforations, which may explain previous scattering experiments suggesting a modulated-lamellar (ML) phase.

Conservative upwind difference schemes for the Euler equations for real gas flows in a duct

In a recent paper [P. Glaister, Conservative upwind difference schemes for compressible flows in a Duct, Comput. Math. Appl. 56 (2008) 1787–1796] numerical schemes based on a conservative linearisation are presented for the Euler equations governing compressible flows of an ideal gas in a duct of variable cross-section, and in [P. Glaister, Conservative upwind difference schemes for compressible flows of a real gas, Comput. Math. Appl. 48 (2004) 469–480] schemes based on this philosophy are presented for real gas flows with slab symmetry. In this paper we seek to extend these ideas to encompass compressible flows of real gases in a duct. This will incorporate the handling of additional terms arising out of the variable geometry and the non-ideal nature of the gas.

Modelling oil absorption during post-frying cooling - I: model development

Several studies have highlighted the importance of the cooling period in oil absorption in deep-fat fried products. Specifically, it has been established that the largest proportion of oil which ends up into the food, is sucked into the porous crust region after the fried product is removed from the oil bath, stressing the importance of this time interval. The main objective of this paper was to develop a predictive mechanistic model that can be used to understand the principles behind post-frying cooling oil absorption kinetics, which can also help identifying the key parameters that affect the final oil intake by the fried product. The model was developed for two different geometries, an infinite slab and an infinite cylinder, and was divided into two main sub-models, one describing the immersion frying period itself and the other describing the post-frying cooling period. The immersion frying period was described by a transient moving-front model that considered the movement of the crust/core interface, whereas post-frying cooling oil absorption was considered to be a pressure driven flow mediated by capillary forces. A key element in the model was the hypothesis that oil suction would only begin once a positive pressure driving force had developed. The mechanistic model was based on measurable physical and thermal properties, and process parameters with no need of empirical data fitting, and can be used to study oil absorption in any deep-fat fried product that satisfies the assumptions made.

Modelling oil absorption during post-frying cooling - II: solution of the mathematical model, model testing and simulations

The mathematical models that describe the immersion-frying period and the post-frying cooling period of an infinite slab or an infinite cylinder were solved and tested. Results were successfully compared with those found in the literature or obtained experimentally, and were discussed in terms of the hypotheses and simplifications made. The models were used as the basis of a sensitivity analysis. Simulations showed that a decrease in slab thickness and core heat capacity resulted in faster crust development. On the other hand, an increase in oil temperature and boiling heat transfer coefficient between the oil and the surface of the food accelerated crust formation. The model for oil absorption during cooling was analysed using the tested post-frying cooling equation to determine the moment in which a positive pressure driving force, allowing oil suction within the pore, originated. It was found that as crust layer thickness, pore radius and ambient temperature decreased so did the time needed to start the absorption. On the other hand, as the effective convective heat transfer coefficient between the air and the surface of the slab increased the required cooling time decreased. In addition, it was found that the time needed to allow oil absorption during cooling was extremely sensitive to pore radius, indicating the importance of an accurate pore size determination in future studies.

A similarity solution for a shock reflection problem in isentropic gas dynamics

A one-dimensional shock-reflection test problem in the case of slab, cylindrical, or spherical symmetry is discussed. The differential equations for a similarity solution are derived and solved numerically in conjunction with the Rankie-Hugoniot shock relations.