Pilot monitoring study of ibuprofen in surface waters of north of Portugal

Ibuprofen is amongst the most worldwide consumed pharmaceuticals. The present work presents the first data in the occurrence of ibuprofen in Portuguese surface waters, focusing in the north area of the country, which is one of the most densely populated areas of Portugal. Analysis of ibuprofen is based on pre-concentration of the analyte with solid phase extraction and subsequent determination with liquid chromatography coupled to fluorescence detection. A total of 42 water samples, including surface waters, landfill leachates,Wastewater Treatment Plant (WWTP), and hospital effluents, were analyzed in order to evaluate the occurrence of ibuprofen in the north of Portugal. In general, the highest concentrations were found in the river mouths and in the estuarine zone. The maximum concentrations found were 48,720 ngL−1 in the landfill leachate, 3,868 ngL−1 in hospital effluent, 616 ngL−1 in WWTP effluent, and 723 ngL−1 in surface waters (Lima river). Environmental risk assessment was evaluated and at the measured concentrations only landfill leachates reveal potential ecotoxicological risk for aquatic organisms. Owing to a high consumption rate of ibuprofen among Portuguese population, as prescribed and nonprescribed medicine, the importance of hospitals, WWTPs, and landfills as sources of entrance of pharmaceuticals in the environment was pointed out. Landfill leachates showed the highest contribution for ibuprofen mass loading into surface waters. On the basis of our findings, more studies are needed as an attempt to assess more vulnerable areas.

Determination of ochratoxin A in bread: evaluation of microwave-assisted extraction using an orthogonal composite design coupled with response surface methodology

An analytical method using microwave-assisted extraction (MAE) and liquid chromatography (LC) with fluorescence detection (FD) for the determination of ochratoxin A (OTA) in bread samples is described. A 24 orthogonal composite design coupled with response surface methodology was used to study the influence of MAE parameters (extraction time, temperature, solvent volume, and stirring speed) in order to maximize OTA recovery. The optimized MAE conditions were the following: 25 mL of acetonitrile, 10 min of extraction, at 80 °C, and maximum stirring speed. Validation of the overall methodology was performed by spiking assays at five levels (0.1–3.00 ng/g). The quantification limit was 0.005 ng/g. The established method was then applied to 64 bread samples (wheat, maize, and wheat/maize bread) collected in Oporto region (Northern Portugal). OTAwas detected in 84 % of the samples with a maximum value of 2.87 ng/g below the European maximum limit established for OTA in cereal products of 3 ng/g.

Response surface methodology applied to SPE for the determination of ibuprofen in various types of water samples

Over the last few years, there has been a growing concern about the presence of pharmaceuticals in the environment. The main objective of this study was to develop and validate an SPE method using surface response methodology for the determination of ibuprofen in different types of water samples. The influence of sample pH and sample volume on the ibuprofen recovery was studied. The effect of each studied independent variable is pronounced on the dependent variable (ibuprofen recovery). Good selectivity, extraction efficiency, and precision were achieved using 600 mL of sample volume with the pH adjusted to 2.2. LC with fluorescence detection was employed. The optimized method was applied to 20 water samples from the North and South of Portugal.

Survey of hearing disorders in an urban population in Rondonia, Northern Brazil

OBJECTIVE: To identify the prevalence of hearing loss for the population in the urban area. METHODS: A cross-sectional household survey based on the World Health Organization Ear and Hearing Disorders Survey Protocol was conducted in 298 households in the urban area of Monte Negro, Rondonia, Northern Brazil, from 2005 to 2007. Ear examinations, behavioral audiometry and pure tone audiometry were conducted on 577 individuals. RESULTS: The results showed that 3.8% (95%CI 2.17;5.45) of population were classified in the disabling hearing impairment category. The prevalence of moderate hearing impairment was 3.4%; severe impairment was 0.4%; and profound hearing impairment was not found. CONCLUSIONS: The impairing hearing loss prevalence found in this study is within of the international prevalence for this level of hearing loss and smaller than observed in a previous study in the South region of Brazil.

Common mental disorders and intimate partner violence in pregnancy

OBJECTIVE : To investigate the association between common mental disorders and intimate partner violence during pregnancy. METHODS : A cross sectional study was carried out with 1,120 pregnant women aged 18-49 years old, who were registered in the Family Health Program in the city of Recife, Northeastern Brazil, between 2005 and 2006. Common mental disorders were assessed using the Self-Reporting Questionnaire (SRQ-20). Intimate partner violence was defined as psychologically, physically and sexually abusive acts committed against women by their partners. Crude and adjusted odds ratios were estimated for the association studied utilizing logistic regression analysis. RESULTS : The most common form of partner violence was psychological. The prevalence of common mental disorders was 71.0% among women who reported all form of violence in pregnancy and 33.8% among those who did not report intimate partner violence. Common mental disorders were associated with psychological violence (OR 2.49, 95%CI 1.8;3.5), even without physical or sexual violence. When psychological violence was combined with physical or sexual violence, the risk of common mental disorders was even higher (OR 3.45; 95%CI 2.3;5.2). CONCLUSIONS : Being assaulted by someone with whom you are emotionally involved can trigger feelings of helplessness, low self-esteem and depression. The pregnancy probably increased women`s vulnerability to common mental disorders

Occupational Musculoskeletal Disorders in Europe: Impact, Risk factors and Preventive Regulations

The aim of this article is to characterize musculoskeletal disorders (MSDs) in EU working population according to available Eurostat data, to identify relevant risk factors and to refer existing legislation and standards to prevent MSDs. The following questions will be answered: How often do MSDs occur in EU? What are the risk factors? Do legislation and standards exist to prevent these disorders?

Répartition des foraminifères benthiques dans les gisements de surface du Miocène d'Aquitaine (SW de la France)

The Aquitaine Basin (southwestern France) is known since long ago for its richness in marine miocene deposits of various facies. A few stratotypes concerning this period have been described in the investigated area. The stratigraphical framework has been recently revised and the study of new exposures completes our knowledge on these levels. In the present work, the authors produce a biostratigraphical distribution of about 160 species (larger and smaller foraminifera), found in the surface exposures of Aquitaine, from the topmost Oligocene (Chattian) through to Middle Miocene (including Serravallian). As a rule, the common species without significant ranges have not bcen mentioned. The microfaunas of several exposures have been thoroughly revised, which has allowed to precise the distribution of many species and induced a few modifications of the results previously produced. Synonymy problems and new taxonomical revisions have been taken into account. Of course, this work will be probably submitted to some changes according to new research on the already known exposures or other more recently discovered.

Analysis of the nano-surface of a modified glassy carbon electrode by pseudo phase plane method

This paper presents the Pseudo phase plane (PPP) method for detecting the existence of a nanofilm on the nitroazobenzene-modified glassy carbon electrode (NAB-GC) system. This modified electrode systems and nitroazobenze-nanofilm were prepared by the electrochemical reduction of diazonium salt of NAB at the glassy carbon electrodes (GCE) in nonaqueous media. The IR spectra of the bare glassy carbon electrodes (GCE), the NAB-GC electrode system and the organic NAB film were recorded. The IR data of the bare GC, NAB-GC and NAB film were categorized into five series consisting of FILM1, GC-NAB1, GC1; FILM2, GC-NAB2, GC2; FILM3, GC-NAB3, GC3 and FILM4, GC-NAB4, GC4 respectively. The PPP approach was applied to each group of the data of unmodified and modified electrode systems with nanofilm. The results provided by PPP method show the existence of the NAB film on the modified GC electrode.

Shear strength of adhesively bonded polyolefins with minimal surface preparation

Interest in polyethylene and polypropylene bonding has increased in the last years. However, adhesive joints with adherends which are of low surface energy and which are chemically inert present several difficulties. Generally, their high degree of chemical resistance to solvents and dissimilar solubility parameters limit the usefulness of solvent bonding as a viable assembly technique. One successful approach to adhesive bonding of these materials involves proper selection of surface pre-treatment prior to bonding. With the correct pre-treatment it is possible to glue these materials with one or more of several adhesives required by the applications involved. A second approach is the use of adhesives without surface pre-treatment, such as hot melts, high tack pressure-sensitive adhesives, solvent-based specialty adhesives and, more recently, structural acrylic adhesives as such 3M DP-8005® and Loctite 3030®. In this paper, the shear strengths of two acrylic adhesives were evaluated using the lap shear test method ASTM D3163 and the block shear test method ASTM D4501. Two different industrial polyolefins (polyethylene and polypropylene) were used for adherends. However, the focus of this study was to measure the shear strength of polyethylene joints with acrylic adhesives. The effect of abrasion was also studied. Some test specimens were manually abraded using 180 and 320 grade abrasive paper. An additional goal of this work was to examine the effect of temperature and moisture on mechanical strength of adhesive joints.

Surface morphology and phase transformations of femtosecond laser-processed saphire

The morphological and structural modifications induced in sapphire by surface treatment with femtosecond laser radiation were studied. Single-crystal sapphire wafers cut parallel to the (0 1 2) planes were treated with 560 fs, 1030 nm wavelength laser radiation using wide ranges of pulse energy and repetition rate. Self-ordered periodic structures with an average spatial periodicity of similar to 300 nm were observed for fluences slightly higher than the ablation threshold. For higher fluences the interaction was more disruptive and extensive fracture, exfoliation, and ejection of ablation debris occurred. Four types of particles were found in the ablation debris: (a) spherical nanoparticles about 50 nm in diameter; (b) composite particles between 150 and 400 nm in size; (c) rounded resolidified particles about 100-500 nm in size; and (d) angular particles presenting a lamellar structure and deformation twins. The study of those particles by selected area electron diffraction showed that the spherical nanoparticles and the composite particles are amorphous, while the resolidified droplets and the angular particles, present a crystalline a-alumina structure, the same of the original material. Taking into consideration the existing ablation theories, it is proposed that the spherical nanoparticles are directly emitted from the surface in the ablation plume, while resolidified droplets are emitted as a result of the ablation process, in the liquid phase, in the low intensity regime, and by exfoliation, in the high intensity regime. Nanoparticle clusters are formed by nanoparticle coalescence in the cooling ablation plume. (C) 2013 Elsevier B.V. All rights reserved.

ERICA: prevalence of common mental disorders in Brazilian adolescents

ABSTRACT OBJECTIVE To describe the prevalence of common mental disorders in Brazilian adolescent students, according to geographical macro-regions, school type, sex, and age. METHODS We evaluated 74,589 adolescents who participated in the Cardiovascular Risk Study in Adolescents (ERICA), a cross-sectional, national, school-based study conducted in 2013-2014 in cities with more than 100,000 inhabitants. A self-administered questionnaire and an electronic data collector were employed. The presence of common mental disorders was assessed using the General Health Questionnaire (GHQ-12). We estimated prevalence and 95% confidence intervals of common mental disorders by sex, age, and school type, in Brazil and in the macro-regions, considering the sample design. RESULTS The prevalence of common mental disorders was of 30.0% (95%CI 29.2-30.8), being higher among girls (38.4%; 95%CI 37.1-39.7) when compared to boys (21.6%; 95%CI 20.5-22.8), and among adolescents who were from 15 to 17 years old (33.6%; 95%CI 32.2-35.0) compared to those aged between 12 and 14 years (26.7%; 95%CI 25.8-27.6). The prevalence of common mental disorders increased with age for both sexes, always higher in girls (ranging from 28.1% at 12 years to 44.1% at 17 years) than in boys (ranging from 18.5% at 12 years to 27.7% at 17 years). We did not observe any significant difference by macro-region or school type. Stratified analyses showed higher prevalence of common mental disorders among girls aged from 15 to 17 years of private schools in the North region (53.1; 95%CI 46.8-59.4). CONCLUSIONS The high prevalence of common mental disorders among adolescents and the fact that the symptoms are often vague mean these disorders are not so easily identified by school administrators or even by health services. The results of this study can help the proposition of more specific prevention and control measures, focused on highest risk subgroups.

Comparison of deposited surface area of airbone ultrafine particles generated from two welding processes

This article describes work performed on the assessment of the levels of airborne ultrafine particles emitted in two welding processes metal-active gas (MAG) of carbon steel and friction-stir welding (FSW) of aluminium in terms of deposited area in alveolar tract of the lung using a nanoparticle surface area monitor analyser. The obtained results showed the dependence from process parameters on emitted ultrafine particles and clearly demonstrated the presence of ultrafine particles, when compared with background levels. The obtained results showed that the process that results on the lower levels of alveolar-deposited surface area is FSW, unlike MAG. Nevertheless, all the tested processes resulted in important doses of ultrafine particles that are to be deposited in the human lung of exposed workers.

Properties of patchy colloidal particles close to a surface: a Monte Carlo and density functional study

We investigate the behavior of a patchy particle model close to a hard-wall via Monte Carlo simulation and density functional theory (DFT). Two DFT approaches, based on the homogeneous and inhomogeneous versions of Wertheim's first order perturbation theory for the association free energy are used. We evaluate, by simulation and theory, the equilibrium bulk phase diagram of the fluid and analyze the surface properties for two isochores, one of which is close to the liquid side of the gas-liquid coexistence curve. We find that the density profile near the wall crosses over from a typical high-temperature adsorption profile to a low-temperature desorption one, for the isochore close to coexistence. We relate this behavior to the properties of the bulk network liquid and find that the theoretical descriptions are reasonably accurate in this regime. At very low temperatures, however, an almost fully bonded network is formed, and the simulations reveal a second adsorption regime which is not captured by DFT. We trace this failure to the neglect of orientational correlations of the particles, which are found to exhibit surface induced orientational order in this regime.

Acute Hepatitis B in a patient previously positive for antibody to surface antigen (anti-HBs) determined by radioimmunoassay: case report and review of the literature

The determination of anti-HBs as a screening test before vaccination has been advisable in order to encounter immune individuals that don't need to receive vaccine protection. A case-report is presented and three other cases are reviewed from the literature. Anti-HBs was positive in these health-care personnels that developped typical acute B hepatitis. Different subtyping involving the d/y determinants were found in the first case, but false-positive anti-HBs even with high titres, determined by RIA, were found in the other cases. Concomitant determination of anti-HBc or absence of screening tests seem to be more reasonable policies until a low-cost and risk-free vaccine is produced.

Paracoccidioidomicose ocular: relato de um caso com coriorretinite posterior

É descrito um caso de paracoccidioidomicose com envolvimento ocular. Pela primeira vez descreve-se a presença do fungo em lesão granulomatosa de coróide. Os Autores revêm os casos de paracoccidioidomicose com acometimento do trato uveal já descritos na literatura e analisam os achados clínicos e anátomo-patológicos destes e do presente relato.