ANNEALING BEHAVIOR OF RAFM ODS-EUROFER STEEL

Oxide-dispersion-strengthened (ODS) ferritic-martensitic steels are candidates for applications in fusion power plants where micro structural long-term stability at temperatures of 650 degrees C to 700 degrees C are required. The microstructural stability of 80% cold-rolled reduced-activation ferritic-martensitic 9% Cr ODS-Eurofer steel was investigated within a wide range of temperatures (300 degrees C to 1350 degrees C). Fine oxide dispersion is very effective to prevent recrystallization in the ferritic phase field. The low recrystallized volume fraction (<0.1) found in samples annealed at 800 degrees C is associated with the nuclei found at prior grain boundaries and around coarse M23C6 particles. The combination of retarding effects such as Zener drag and concurrent recovery decrease the local stored energy and impede further growth of the recrystallization nuclei. Above 90 degrees C, martensitic transformation takes place with consequent coarsening. Significant changes in crystallographic texture are also reported.

New measurement of the B-11(p,alpha(0))Be-8 bare-nucleus S(E) factor via the Trojan horse method

A new measurement of the B-11(p,alpha(0))Be-8 has been performed applying the Trojan horse method (THM) to the H-2(B-11,alpha Be-8(0))n quasi-free reaction induced at a laboratory energy of 27 MeV. The astrophysical S(E) factor has been extracted from similar to 600 keV down to zero energy by means of an improved data analysis technique and it has been compared with direct data available in the literature. The range investigated here overlaps with the energy region of the light element LiBeB stellar burning and with that of future aneutronic fusion power plants using the B-11+p fuel cycle. The new investigation described here confirms the preliminary results obtained in the recent TH works. The origin of the discrepancy between the direct estimate of the B-11(p,alpha(0))Be-8 S(E)-factor at zero energy and that from a previous THM investigation is quantitatively corroborated. The results obtained here support, within the experimental uncertainties, the low-energy S(E)-factor extrapolation and the value of the electron screening potential deduced from direct measurements.

Mitigazione sequestro e stoccaggio di diossido di carbonio

The main objective of my thesis was the technical-economic feasibility of a system of electricity generation integrated with CCS. The policy framework for development processing is part of the recent attention that at the political level has been directed towards the use of CCS technologies with the aim of addressing the problems of actual climate change. Several technological options have been proposed to stabilize and reduce the atmospheric concentrations of carbon dioxide (CO2) among which, the most promising for IPPC (Intergovernmental Panel on Climate Change)are the CCS technologies (Carbon Capture and Storage & Carbon Capture and Sequestration). The remedy proposed for large stationary CO2 sources as thermoelectric power plants is to separate the flue gas capturing CO2 and to store it into deep subsurface geological formations (more than 800 meters of depth). In order to support the identification of potential CO2 storage reservoirs in Italy and in Europe by Geo Capacity(an European database) new studies are developing. From the various literature data analyzed shows that most of the CO2 emitted from large stationary sources comes from the processes of electricity generation (78% of total emissions) and from (about 60%) those using coal especially. The CCS have the objective of return "to the sender" , the ground, the carbon in oxidized form (CO2) after it has been burned by man starting from its reduced form (CH4, oil and coal), then the carbon dioxide is not a "pollutant" if injected into the subsurface, CO2 is an acid reagent that interacts with the rock, with underground fluid and the characteristics of the host rock. The results showed that the CCS technology are very urgent, because unfortunately there are too many industrial sources of CO2 in assets (power plants, refineries, cement plants, steel mills) in the world who are carrying too quickly the CO2 atmospheric concentration levels to values that aren't acceptable for our dear planet.

Riconversione degli impianti saccariferi per la valorizzazione della filiera agro-energetica: analisi di impatto sul comprensorio agricolo

Il presente lavoro trae origine dagli obiettivi e dalle relative misure applicative della riforma dell’OCM zucchero del 2006 e nello specifico dal Piano nazionale per la razionalizzazione e riconversione della produzione bieticolo-saccarifera approvato dal MIPAF nel 2007. Lo studio riguarda la riconversione dello zuccherificio di Finale Emilia (MO), di appartenenza del Gruppo bieticolo-saccarifero Co.Pro.B, in un impianto di generazione di energia elettrica e termica che utilizza biomassa di origine agricola per la combustione diretta. L'alimentazione avviene principalmente dalla coltivazione dedicata del sorgo da fibra (Sorghum bicolor), integrata con risorse agro-forestali. Lo studio mostra la necessità di coltivazione di 4.400 ettari di sorgo da fibra con una produzione annua di circa 97.000 t di prodotto al 75% di sostanza secca necessari per l’alimentazione della centrale a biomassa. L’obiettivo é quello di valutare l’impatto della nuova coltura energetica sul comprensorio agricolo e sulla economia dell’impresa agricola. La metodologia adottata si basa sulla simulazione di modelli aziendali di programmazione lineare che prevedono l’inserimento del sorgo da fibra come coltura energetica nel piano ottimo delle aziende considerate. I modelli predisposti sono stati calibrati su aziende RICA al fine di riprodurre riparti medi reali su tre tipologie dimensionali rappresentative: azienda piccola entro i 20 ha, media da 20 a 50 ha e grande oltre i 50 ha. La superficie di entrata a livello aziendale, se rapportata alla rappresentatività delle aziende dell’area di studio, risulta insufficiente per soddisfare la richiesta di approvvigionamento dell’impianto a biomassa. Infatti con tale incremento la superficie di coltivazione nel comprensorio si attesta sui 2.500 ettari circa contro i 4.400 necessari alla centrale. Lo studio mostra pertanto che occorre un incentivo superiore, di circa 80-90 €/ha, per soddisfare la richiesta della superficie colturale a livello di territorio. A questi livelli, la disponibilità della coltura energetica sul comprensorio risulta circa 9.500 ettari.

Whole ship energy optimization: the case study of a chemical tanker

La presente dissertazione investiga la possibilità di ottimizzare l’uso di energia a bordo di una nave per trasporto di prodotti chimici e petrolchimici. Il software sviluppato per questo studio può essere adattato a qualsiasi tipo di nave. Tale foglio di calcolo fornisce la metodologia per stimare vantaggi e miglioramenti energetici, con accuratezza direttamente proporzionale ai dati disponibili sulla configurazione del sistema energetico e sui dispositivi installati a bordo. Lo studio si basa su differenti fasi che permettono la semplificazione del lavoro; nell’introduzione sono indicati i dati necessari per svolgere un’accurata analisi ed è presentata la metodologia adottata. Inizialmente è fornita una spiegazione sul layout dell’impianto, sulle sue caratteristiche e sui principali dispositivi installati a bordo. Vengono dunque trattati separatamente i principali carichi, meccanico, elettrico e termico. In seguito si procede con una selezione delle principali fasi operative della nave: è seguito tale approccio in modo da comprendere meglio la ripartizione della richiesta di potenza a bordo della nave e il suo sfruttamento. Successivamente è svolto un controllo sul dimensionamento del sistema elettrico: ciò aiuta a comprendere se la potenza stimata dai progettisti sia assimilabile a quella effettivamente richiesta sulla nave. Si ottengono in seguito curve di carico meccanico, elettrico e termico in funzione del tempo per tutte le fasi operative considerate: tramite l’uso del software Visual Basic Application (VBA) vengono creati i profili di carico che possono essere gestiti nella successiva fase di ottimizzazione. L’ottimizzazione rappresenta il cuore di questo studio; i profili di potenza ottenuti dalla precedente fase sono gestiti in modo da conseguire un sistema che sia in grado di fornire potenza alla nave nel miglior modo possibile da un punto di vista energetico. Il sistema energetico della nave è modellato e ottimizzato mantenendo lo status quo dei dispositivi di bordo, per i quali sono considerate le configurazioni di “Load following”, “two shifts” e “minimal”. Una successiva investigazione riguarda l’installazione a bordo di un sistema di accumulo di energia termica, così da migliorare lo sfruttamento dell’energia disponibile. Infine, nella conclusione, sono messi a confronto i reali consumi della nave con i risultati ottenuti con e senza l’introduzione del sistema di accumulo termico. Attraverso la configurazione “minimal” è possibile risparmiare circa l’1,49% dell’energia totale consumata durante un anno di attività; tale risparmio è completamente gratuito poiché può essere raggiunto seguendo alcune semplici regole nella gestione dell’energia a bordo. L’introduzione di un sistema di accumulo termico incrementa il risparmio totale fino al 4,67% con un serbatoio in grado di accumulare 110000 kWh di energia termica; tuttavia, in questo caso, è necessario sostenere il costo di installazione del serbatoio. Vengono quindi dibattuti aspetti economici e ambientali in modo da spiegare e rendere chiari i vantaggi che si possono ottenere con l’applicazione di questo studio, in termini di denaro e riduzione di emissioni in atmosfera.

Studio, simulazione e verifica sperimentale di tecniche di controllo per convertitori multilivello modulari

L’evoluzione dei componenti elettronici di potenza ed il conseguente sviluppo dei convertitori statici dell’energia elettrica hanno consentito di ottenere un’elevata efficienza energetica, sia nell’ambito degli azionamenti elettrici, sia nell’ambito della trasmissione e distribuzione dell’energia elettrica. L’efficienza energetica è una questione molto importante nell’attuale contesto storico, in quanto si sta facendo fronte ad una elevatissima richiesta di energia, sfruttando prevalentemente fonti di energia non rinnovabili. L’introduzione dei convertitori statici ha reso possibile un notevolissimo incremento dello sfruttamento delle fonti di energia rinnovabili: si pensi ad esempio agli inverter per impianti fotovoltaici o ai convertitori back to back per applicazioni eoliche. All’aumentare della potenza di un convertitore aumenta la sua tensione di esercizio: le limitazioni della tensione sopportabile dagli IGBT, che sono i componenti elettronici di potenza di più largo impiego nei convertitori statici, rendono necessarie modifiche strutturali per i convertitori nei casi in cui la tensione superi determinati valori. Tipicamente in media ed alta tensione si impiegano strutture multilivello. Esistono più tipi di configurazioni multilivello: nel presente lavoro è stato fatto un confronto tra le varie strutture esistenti e sono state valutate le possibilità offerte dall’architettura innovativa Modular Multilevel Converter, nota come MMC. Attualmente le strutture più diffuse sono la Diode Clamped e la Cascaded. La prima non è modulare, in quanto richiede un’apposita progettazione in relazione al numero di livelli di tensione. La seconda è modulare, ma richiede alimentazioni separate e indipendenti per ogni modulo. La struttura MMC è modulare e necessita di un’unica alimentazione per il bus DC, ma la presenza dei condensatori richiede particolare attenzione in fase di progettazione della tecnica di controllo, analogamente al caso del Diode Clamped. Un esempio di possibile utilizzo del convertitore MMC riguarda le trasmissioni HVDC, alle quali si sta dedicando un crescente interesse negli ultimi anni.

Development of a microgrid with renewable energy sources and electrochemical storage system integration

Beside the traditional paradigm of "centralized" power generation, a new concept of "distributed" generation is emerging, in which the same user becomes pro-sumer. During this transition, the Energy Storage Systems (ESS) can provide multiple services and features, which are necessary for a higher quality of the electrical system and for the optimization of non-programmable Renewable Energy Source (RES) power plants. A ESS prototype was designed, developed and integrated into a renewable energy production system in order to create a smart microgrid and consequently manage in an efficient and intelligent way the energy flow as a function of the power demand. The produced energy can be introduced into the grid, supplied to the load directly or stored in batteries. The microgrid is composed by a 7 kW wind turbine (WT) and a 17 kW photovoltaic (PV) plant are part of. The load is given by electrical utilities of a cheese factory. The ESS is composed by the following two subsystems, a Battery Energy Storage System (BESS) and a Power Control System (PCS). With the aim of sizing the ESS, a Remote Grid Analyzer (RGA) was designed, realized and connected to the wind turbine, photovoltaic plant and the switchboard. Afterwards, different electrochemical storage technologies were studied, and taking into account the load requirements present in the cheese factory, the most suitable solution was identified in the high temperatures salt Na-NiCl2 battery technology. The data acquisition from all electrical utilities provided a detailed load analysis, indicating the optimal storage size equal to a 30 kW battery system. Moreover a container was designed and realized to locate the BESS and PCS, meeting all the requirements and safety conditions. Furthermore, a smart control system was implemented in order to handle the different applications of the ESS, such as peak shaving or load levelling.

Mikrobielle Prozesskontrolle in Biogasanlagen durch Monitoring der Kohlenstoff-Isotopenverhältnisse im Gasbereich

Der zunehmende Anteil von Strom aus erneuerbaren Energiequellen erfordert ein dynamisches Konzept, um Spitzenlastzeiten und Versorgungslücken aus der Wind- und Solarenergie ausgleichen zu können. Biogasanlagen können aufgrund ihrer hohen energetischen Verfügbarkeit und der Speicherbarkeit von Biogas eine flexible Energiebereitstellung ermöglichen und darüber hinaus über ein „Power-to-Gas“-Verfahren bei einem kurzzeitigen Überschuss von Strom eine Überlastung des Stromnetzes verhindern. Ein nachfrageorientierter Betrieb von Biogasanlagen stellt jedoch hohe Anforderungen an die Mikrobiologie im Reaktor, die sich an die häufig wechselnden Prozessbedingungen wie der Raumbelastung im Reaktor anpassen muss. Eine Überwachung des Fermentationsprozesses in Echtzeit ist daher unabdingbar, um Störungen in den mikrobiellen Gärungswegen frühzeitig erkennen und adäquat entgegenwirken zu können. rnBisherige mikrobielle Populationsanalysen beschränken sich auf aufwendige, molekularbiologische Untersuchungen des Gärsubstrates, deren Ergebnisse dem Betreiber daher nur zeitversetzt zur Verfügung stehen. Im Rahmen dieser Arbeit wurde erstmalig ein Laser-Absorptionsspektrometer zur kontinuierlichen Messung der Kohlenstoff-Isotopenverhältnisse des Methans an einer Forschungsbiogasanlage erprobt. Dabei konnten, in Abhängigkeit der Raumbelastung und Prozessbedingungen variierende Isotopenverhältnisse gemessen werden. Anhand von Isolaten aus dem untersuchten Reaktor konnte zunächst gezeigt werden, dass für jeden Methanogenesepfad (hydrogeno-troph, aceto¬klastisch sowie methylotroph) eine charakteristische, natürliche Isotopensignatur im Biogas nachgewiesen werden kann, sodass eine Identifizierung der aktuell dominierenden methanogenen Reaktionen anhand der Isotopen-verhältnisse im Biogas möglich ist. rnDurch den Einsatz von 13C- und 2H-isotopen¬markierten Substraten in Rein- und Mischkulturen und Batchreaktoren, sowie HPLC- und GC-Unter¬suchungen der Stoffwechselprodukte konnten einige bislang unbekannte C-Flüsse in Bioreaktoren festgestellt werden, die sich wiederum auf die gemessenen Isotopenverhältnisse im Biogas auswirken können. So konnte die Entstehung von Methanol sowie dessen mikrobieller Abbauprodukte bis zur finalen CH4-Bildung anhand von fünf Isolaten erstmalig in einer landwirtschaftlichen Biogasanlage rekonstruiert und das Vorkommen methylotropher Methanogenesewege nachgewiesen werden. Mithilfe molekularbiologischer Methoden wurden darüber hinaus methanoxidierende Bakterien zahlreicher, unbekannter Arten im Reaktor detektiert, deren Vorkommen aufgrund des geringen O2-Gehaltes in Biogasanlagen bislang nicht erwartet wurde. rnDurch die Konstruktion eines synthetischen DNA-Stranges mit den Bindesequenzen für elf spezifische Primerpaare konnte eine neue Methode etabliert werden, anhand derer eine Vielzahl mikrobieller Zielorganismen durch die Verwendung eines einheitlichen Kopienstandards in einer real-time PCR quantifiziert werden können. Eine über 70 Tage durchgeführte, wöchentliche qPCR-Analyse von Fermenterproben zeigte, dass die Isotopenverhältnisse im Biogas signifikant von der Zusammensetzung der Reaktormikrobiota beeinflusst sind. Neben den aktuell dominierenden Methanogenesewegen war es auch möglich, einige bakterielle Reaktionen wie eine syntrophe Acetatoxidation, Acetogenese oder Sulfatreduktion anhand der δ13C (CH4)-Werte zu identifizieren, sodass das hohe Potential einer kontinuierlichen Isotopenmessung zur Prozessanalytik in Biogasanlagen aufgezeigt werden konnte.rn

Design and implementation of the ESEO spacecraft simulator

The thesis work is developed under the European Student Earth Orbiter (ESEO) project supported by the European Space Agency (ESA) in order to help prepare a well-qualified space-engineering workforce for Europe's future. In the following chapters we are going to analyse how to simulate some ESEO subsystem. First of all, the Thermal Subsystem that evaluates the temperature evolution of on-board instruments. For this purpose, simulating also the orbital and attitude dynamics of the spacecraft, it is necessary in order to evaluate external environmental fluxes. The Power Subsystem will be the following step and it models the ability of a spacecraft to produce and store electrical energy. Finally, we will integrate in our software a block capable of simulating the communication link between the satellite and the Ground Station (GS). This last step is designed and validated during the thesis preparation.

Review of assessment, design, and mitigation of multiple hazards

Large parts of the world are subjected to one or more natural hazards, such as earthquakes, tsunamis, landslides, tropical storms (hurricanes, cyclones and typhoons), costal inundation and flooding. Virtually the entire world is at risk of man-made hazards. In recent decades, rapid population growth and economic development in hazard-prone areas have greatly increased the potential of multiple hazards to cause damage and destruction of buildings, bridges, power plants, and other infrastructure; thus posing a grave danger to the community and disruption of economic and societal activities. Although an individual hazard is significant in many parts of the United States (U.S.), in certain areas more than one hazard may pose a threat to the constructed environment. In such areas, structural design and construction practices should address multiple hazards in an integrated manner to achieve structural performance that is consistent with owner expectations and general societal objectives. The growing interest and importance of multiple-hazard engineering has been recognized recently. This has spurred the evolution of multiple-hazard risk-assessment frameworks and development of design approaches which have paved way for future research towards sustainable construction of new and improved structures and retrofitting of the existing structures. This report provides a review of literature and the current state of practice for assessment, design and mitigation of the impact of multiple hazards on structural infrastructure. It also presents an overview of future research needs related to multiple-hazard performance of constructed facilities.

Will Whole-Tree Harvest of Jack Pine (Pinus banksiana) deplete soil nutrients in low-productivity sand soils?

In 2009 and 2010 a study was conducted on the Hiawatha National Forest (HNF) to determine if whole-tree harvest (WTH) of jack pine would deplete the soil nutrients in the very coarse-textured Rubicon soil. WTH is restricted on Rubicon sand in order to preserve the soil fertility, but the increasing construction of biomass-fueled power plants is expected to increase the demand for forest biomass. The specific objectives of this study were to estimate biomass and nutrient content of above- and below-ground tree components in mature jack pine (Pinus banksiana) stands growing on a coarse-textured, low-productivity soil, determine pools of total C and N and exchangeable soil cations in Rubicon sand, and to compare the possible impacts of conventional stem-only harvest (CH) and WTH on soil nutrient pools and the implications for productivity of subsequent rotations. Four even-aged jack pine stands on Rubicon soil were studied. Allometric equations were used to estimate above-ground biomass and nutrients, and soil samples from each stand were taken for physical and chemical analysis. Results indicate that WTH will result in cation deficits in all stands, with exceptionally large Ca deficits occurring in two stands. Where a deficit does not occur, the cation surplus is small and, chemical weathering and atmospheric deposition is not anticipated to replace the removed cations. CH will result in a surplus of cations, and will likely not result in productivity declines during the first rotation. However even under CH, the surplus is small, and chemical weathering and atmospheric deposition will not supply enough cations for the second rotation.

Development of an optimization model for biofuel facility size and location and a simulation model for design of a biofuel supply chain

To mitigate greenhouse gas (GHG) emissions and reduce U.S. dependence on imported oil, the United States (U.S.) is pursuing several options to create biofuels from renewable woody biomass (hereafter referred to as “biomass”). Because of the distributed nature of biomass feedstock, the cost and complexity of biomass recovery operations has significant challenges that hinder increased biomass utilization for energy production. To facilitate the exploration of a wide variety of conditions that promise profitable biomass utilization and tapping unused forest residues, it is proposed to develop biofuel supply chain models based on optimization and simulation approaches. The biofuel supply chain is structured around four components: biofuel facility locations and sizes, biomass harvesting/forwarding, transportation, and storage. A Geographic Information System (GIS) based approach is proposed as a first step for selecting potential facility locations for biofuel production from forest biomass based on a set of evaluation criteria, such as accessibility to biomass, railway/road transportation network, water body and workforce. The development of optimization and simulation models is also proposed. The results of the models will be used to determine (1) the number, location, and size of the biofuel facilities, and (2) the amounts of biomass to be transported between the harvesting areas and the biofuel facilities over a 20-year timeframe. The multi-criteria objective is to minimize the weighted sum of the delivered feedstock cost, energy consumption, and GHG emissions simultaneously. Finally, a series of sensitivity analyses will be conducted to identify the sensitivity of the decisions, such as the optimal site selected for the biofuel facility, to changes in influential parameters, such as biomass availability and transportation fuel price. Intellectual Merit The proposed research will facilitate the exploration of a wide variety of conditions that promise profitable biomass utilization in the renewable biofuel industry. The GIS-based facility location analysis considers a series of factors which have not been considered simultaneously in previous research. Location analysis is critical to the financial success of producing biofuel. The modeling of woody biomass supply chains using both optimization and simulation, combing with the GIS-based approach as a precursor, have not been done to date. The optimization and simulation models can help to ensure the economic and environmental viability and sustainability of the entire biofuel supply chain at both the strategic design level and the operational planning level. Broader Impacts The proposed models for biorefineries can be applied to other types of manufacturing or processing operations using biomass. This is because the biomass feedstock supply chain is similar, if not the same, for biorefineries, biomass fired or co-fired power plants, or torrefaction/pelletization operations. Additionally, the research results of this research will continue to be disseminated internationally through publications in journals, such as Biomass and Bioenergy, and Renewable Energy, and presentations at conferences, such as the 2011 Industrial Engineering Research Conference. For example, part of the research work related to biofuel facility identification has been published: Zhang, Johnson and Sutherland [2011] (see Appendix A). There will also be opportunities for the Michigan Tech campus community to learn about the research through the Sustainable Future Institute.

Cladophora, mass transport, and the nearshore phosphorus shunt

Excessive Cladophora growth in the Great Lakes has led to beach fouling and the temporary closure of nuclear power plants and has been associated with avian botulism and the persistence of human pathogens. As the growth-limiting nutrient for Cladophora, phosphorus is the appropriate target for management efforts. Dreissenids (zebra and quagga mussels) have the ability to capture particulate phase phosphorus (otherwise unavailable to Cladophora) and release it in a soluble, available form. The significance of this potential nutrient source is, in part, influenced by the interplay between phosphorus flux from the mussel bed and turbulent mixing in establishing the phosphorus levels to which Cladophora is exposed. It is hypothesized that under quiescent conditions phosphorus will accumulate near the sediment-water interface, setting up vertical phosphorus gradients and favorable conditions for resource delivery to Cladophora. These gradients would be eliminated under conditions of wind mixing, reducing the significance of the dreissenid-mediated nutrient contribution. Soluble reactive phosphorus (SRP) levels were monitored over dreissenid beds (densities on the order of 350•m-2 and 3000∙m-2) at a site 8 m deep in Lake Michigan. Monitoring was based on the deployment of Modified Hesslein Samplers which collected samples for SRP analysis over a distance of 34 cm above the bottom in 2.5 cm intervals. Deployment intervals were established to capture a wind regime (calm, windy) that persisted for an interval consistent with the sampler equilibration time of 7 hours. Results indicate that increased mussel density leads to an increased concentration boundary layer; increased wind speed leads to entrainment of the concentration boundary layer; and increased duration of quiescent periods leads to an increased concentration boundary layer. This concentration boundary layer is of ecological significance and forms in the region inhabited by Cladophora

DEVELOPMENT OF AN OPTIMIZATION MODEL FOR BIOFUEL FACILITY SIZE AND LOCATION AND A SIMULATION MODEL FOR DESIGN OF A BIOFUEL SUPPLY CHAIN

A range of societal issues have been caused by fossil fuel consumption in the transportation sector in the United States (U.S.), including health related air pollution, climate change, the dependence on imported oil, and other oil related national security concerns. Biofuels production from various lignocellulosic biomass types such as wood, forest residues, and agriculture residues have the potential to replace a substantial portion of the total fossil fuel consumption. This research focuses on locating biofuel facilities and designing the biofuel supply chain to minimize the overall cost. For this purpose an integrated methodology was proposed by combining the GIS technology with simulation and optimization modeling methods. The GIS based methodology was used as a precursor for selecting biofuel facility locations by employing a series of decision factors. The resulted candidate sites for biofuel production served as inputs for simulation and optimization modeling. As a precursor to simulation or optimization modeling, the GIS-based methodology was used to preselect potential biofuel facility locations for biofuel production from forest biomass. Candidate locations were selected based on a set of evaluation criteria, including: county boundaries, a railroad transportation network, a state/federal road transportation network, water body (rivers, lakes, etc.) dispersion, city and village dispersion, a population census, biomass production, and no co-location with co-fired power plants. The simulation and optimization models were built around key supply activities including biomass harvesting/forwarding, transportation and storage. The built onsite storage served for spring breakup period where road restrictions were in place and truck transportation on certain roads was limited. Both models were evaluated using multiple performance indicators, including cost (consisting of the delivered feedstock cost, and inventory holding cost), energy consumption, and GHG emissions. The impact of energy consumption and GHG emissions were expressed in monetary terms to keep consistent with cost. Compared with the optimization model, the simulation model represents a more dynamic look at a 20-year operation by considering the impacts associated with building inventory at the biorefinery to address the limited availability of biomass feedstock during the spring breakup period. The number of trucks required per day was estimated and the inventory level all year around was tracked. Through the exchange of information across different procedures (harvesting, transportation, and biomass feedstock processing procedures), a smooth flow of biomass from harvesting areas to a biofuel facility was implemented. The optimization model was developed to address issues related to locating multiple biofuel facilities simultaneously. The size of the potential biofuel facility is set up with an upper bound of 50 MGY and a lower bound of 30 MGY. The optimization model is a static, Mathematical Programming Language (MPL)-based application which allows for sensitivity analysis by changing inputs to evaluate different scenarios. It was found that annual biofuel demand and biomass availability impacts the optimal results of biofuel facility locations and sizes.