Calibration uncertainty estimation for internal aerodynamic balance

Aerodynamic balances are employed in wind tunnels to estimate the forces and moments acting on the model under test. This paper proposes a methodology for the assessment of uncertainty in the calibration of an internal multi-component aerodynamic balance. In order to obtain a suitable model to provide aerodynamic loads from the balance sensor responses, a calibration is performed prior to the tests by applying known weights to the balance. A multivariate polynomial fitting by the least squares method is used to interpolate the calibration data points. The uncertainties of both the applied loads and the readings of the sensors are considered in the regression. The data reduction includes the estimation of the calibration coefficients, the predicted values of the load components and their corresponding uncertainties, as well as the goodness of fit.

Modeling approach based on experimental results for prediction of measurement errors in energy meters

This paper presents a general modeling approach to investigate and to predict measurement errors in active energy meters both induction and electronic types. The measurement error modeling is based on Generalized Additive Model (GAM), Ridge Regression method and experimental results of meter provided by a measurement system. The measurement system provides a database of 26 pairs of test waveforms captured in a real electrical distribution system, with different load characteristics (industrial, commercial, agricultural, and residential), covering different harmonic distortions, and balanced and unbalanced voltage conditions. In order to illustrate the proposed approach, the measurement error models are discussed and several results, which are derived from experimental tests, are presented in the form of three-dimensional graphs, and generalized as error equations. © 2009 IEEE.

Design of a CMOS voltage reference using current-model approach

A voltage reference with low sensibility to temperature and power-supply that can generate flexible reference values (from milivolts to several volts) is proposed. Designed for AMS 0.35μm CMOS process, the circuit provides a stable output voltage working in the temperature range of -40-150°C. The proposed reference provides a nominal output voltage of 1.358V with a power-supply of 3.3V. © 2011 IEEE.

Optimal phasor measurement units placement for fault location on overhead electric power distribution feeders

This paper proposes a new approach for optimal phasor measurement units placement for fault location on electric power distribution systems using Greedy Randomized Adaptive Search Procedure metaheuristic and Monte Carlo simulation. The optimized placement model herein proposed is a general methodology that can be used to place devices aiming to record the voltage sag magnitudes for any fault location algorithm that uses voltage information measured at a limited set of nodes along the feeder. An overhead, three-phase, three-wire, 13.8 kV, 134-node, real-life feeder model is used to evaluate the algorithm. Tests show that the results of the fault location methodology were improved thanks to the new optimized allocation of the meters pinpointed using this methodology. © 2011 IEEE.

Chemometric analysis of Hymenoptera toxins and defensins: A model for predicting the biological activity of novel peptides from venoms and hemolymph

When searching for prospective novel peptides, it is difficult to determine the biological activity of a peptide based only on its sequence. The trial and error approach is generally laborious, expensive and time consuming due to the large number of different experimental setups required to cover a reasonable number of biological assays. To simulate a virtual model for Hymenoptera insects, 166 peptides were selected from the venoms and hemolymphs of wasps, bees and ants and applied to a mathematical model of multivariate analysis, with nine different chemometric components: GRAVY, aliphaticity index, number of disulfide bonds, total residues, net charge, pI value, Boman index, percentage of alpha helix, and flexibility prediction. Principal component analysis (PCA) with non-linear iterative projections by alternating least-squares (NIPALS) algorithm was performed, without including any information about the biological activity of the peptides. This analysis permitted the grouping of peptides in a way that strongly correlated to the biological function of the peptides. Six different groupings were observed, which seemed to correspond to the following groups: chemotactic peptides, mastoparans, tachykinins, kinins, antibiotic peptides, and a group of long peptides with one or two disulfide bonds and with biological activities that are not yet clearly defined. The partial overlap between the mastoparans group and the chemotactic peptides, tachykinins, kinins and antibiotic peptides in the PCA score plot may be used to explain the frequent reports in the literature about the multifunctionality of some of these peptides. The mathematical model used in the present investigation can be used to predict the biological activities of novel peptides in this system, and it may also be easily applied to other biological systems. © 2011 Elsevier Inc.

Specialist tool for monitoring the measurement degradation process of induction active energy meters

This paper presents a methodology and a specialist tool for failure probability analysis of induction type watt-hour meters, considering the main variables related to their measurement degradation processes. The database of the metering park of a distribution company, named Elektro Electricity and Services Co., was used for determining the most relevant variables and to feed the data in the software. The modeling developed to calculate the watt-hour meters probability of failure was implemented in a tool through a user friendly platform, written in Delphi language. Among the main features of this tool are: analysis of probability of failure by risk range; geographical localization of the meters in the metering park, and automatic sampling of induction type watt-hour meters, based on a risk classification expert system, in order to obtain information to aid the management of these meters. The main goals of the specialist tool are following and managing the measurement degradation, maintenance and replacement processes for induction watt-hour meters. © 2011 IEEE.

Evidence for associated production of a single top quark and W Boson in pp collisions at √s=7 TeV

Evidence is presented for the associated production of a single top quark and W boson in pp collisions at √s=7 TeV with the CMS experiment at the LHC. The analyzed data correspond to an integrated luminosity of 4.9 fb -1. The measurement is performed using events with two leptons and a jet originated from a b quark. A multivariate analysis based on kinematic properties is utilized to separate the tt̄ background from the signal. The observed signal has a significance of 4.0σ and corresponds to a cross section of 16-4+5 pb, in agreement with the standard model expectation of 15.6±0.4-1.2+1.0 pb. © 2013 CERN, for the CMS Collaboration Published by the American Physical Society under the terms of the http://creativecommons.org/licenses/by/3.0/ Creative Commons Attribution 3.0 License. Further distribution of this work must maintain attribution to the author(s) and the published article's title, journal citation, and DOI.

Measurement of the sum of WW and WZ production with W+dijet events in pp collisions at √s = 7 TeV

A measurement of the inclusive WW+WZ diboson production cross section in proton-proton collisions is reported, based on events containing a leptonically decaying W boson and exactly two jets. The data sample, collected at √s = 7 TeV with the CMS detector at the LHC, corresponds to an integrated luminosity of 5. 0 fb-1. The measured value of the sum of the inclusive WW and WZ cross sections is σ(pp→WW+WZ)=68. 9±8. 7 (stat.)±9. 7 (syst.)±1. 5 (lum.) pb, consistent with the standard model prediction of 65. 6±2. 2 pb. This is the first measurement of WW+WZ production in pp collisions using this signature. No evidence for anomalous triple gauge couplings is found and upper limits are set on their magnitudes. © 2013 CERN for the benefit of the CMS collaboration.

Determination of disease biomarkers in Eucalyptus by comprehensive two-dimensional gas chromatography and multivariate data analysis

In this paper is reported the use of the chromatographic profiles of volatiles to determine disease markers in plants - in this case, leaves of Eucalyptus globulus contaminated by the necrotroph fungus Teratosphaeria nubilosa. The volatile fraction was isolated by headspace solid phase microextraction (HS-SPME) and analyzed by comprehensive two-dimensional gas chromatography-fast quadrupole mass spectrometry (GC. ×. GC-qMS). For the correlation between the metabolic profile described by the chromatograms and the presence of the infection, unfolded-partial least squares discriminant analysis (U-PLS-DA) with orthogonal signal correction (OSC) were employed. The proposed method was checked to be independent of factors such as the age of the harvested plants. The manipulation of the mathematical model obtained also resulted in graphic representations similar to real chromatograms, which allowed the tentative identification of more than 40 compounds potentially useful as disease biomarkers for this plant/pathogen pair. The proposed methodology can be considered as highly reliable, since the diagnosis is based on the whole chromatographic profile rather than in the detection of a single analyte. © 2013 Elsevier B.V..

Measurement of differential top-quark-pair production cross sections in pp collisions at √s = 7TeV

Normalised differential top-quark-pair production cross sections are measured in pp collisions at a centre-of-mass energy of 7 TeVat the LHC with the CMS detector using data recorded in 2011 corresponding to an integrated luminosity of 5. 0 fb-1. The measurements are performed in the lepton+jets decay channels (e+jets and μ+jets) and the dilepton decay channels (e+}e-, μ+μ-, and μ±e∓). The tt̄ differential cross section is measured as a function of kinematic properties of the final-state charged leptons and jets associated to b quarks, as well as those of the top quarks and the tt̄ system. The data are compared with several predictions from perturbative QCD calculations up to approximate next-to-next-to-leading-order precision. No significant deviations from the standard model are observed. © 2013 CERN for the benefit of the CMS collaboration.

Measurement of the tt̄ production cross section in the τ+jets channel in pp collisions at √s = 7 TeV

The top-quark pair production cross section in 7 TeV center-of-mass energy proton-proton collisions is measured using data collected by the CMS detector at the LHC. The measurement uses events with one jet identified as a hadronically decaying τ lepton and at least four additional energetic jets, at least one of which is identified as coming from a b quark. The analyzed data sample corresponds to an integrated luminosity of 3.9 fb-1 recorded by a dedicated multijet plus hadronically decaying τ trigger. A neural network has been developed to separate the top-quark pairs from the W+jets and multijet backgrounds. The measured value of σtt̄= 152 ± 12,(stat.) ± 32,(syst.) ±,(lum.) pb is consistent with the standard model predictions. © 2013 CERN for the benefit of the CMS collaboration.

Recovery of pulmonary structure and exercise capacity by treatment with granulocyte-colony stimulating factor (G-CSF) in a mouse model of emphysema

Emphysema is a chronic obstructive pulmonary disease characterized abnormal dilatation of alveolar spaces, which impairs alveolar gas exchange, compromising the physical capacity of a patient due to airflow limitations. Here we tested the effects of G-CSF administration in pulmonary tissue and exercise capacity in emphysematous mice. C57Bl/6 female mice were treated with elastase intratracheally to induce emphysema. Their exercise capacities were evaluated in a treadmill. Lung histological sections were prepared to evaluate mean linear intercept measurement. Emphysematous mice were treated with G-CSF (3 cycles of 200 μg/kg/day for 5 consecutive days, with 7-day intervals) or saline and submitted to a third evaluation 8 weeks after treatment. Values of run distance and linear intercept measurement were expressed as mean ± SD and compared applying a paired t-test. Effects of treatment on these parameters were analyzed applying a Repeated Measures ANOVA, followed by Tukey's post hoc analysis. p < 0.05 was considered statistically significant. Twenty eight days later, animals ran significantly less in a treadmill compared to normal mice (549.7 ± 181.2 m and 821.7 ± 131.3 m, respectively; p < 0.01). Treatment with G-CSF significantly increased the exercise capacity of emphysematous mice (719.6 ± 200.5 m), whereas saline treatment had no effect on distance run (595.8 ± 178.5 m). The PCR cytokines genes analysis did not detect difference between experimental groups. Morphometric analyses in the lung showed that saline-treated mice had a mean linear intercept significantly higher (p < 0.01) when compared to mice treated with G-CSF, which did not significantly differ from that of normal mice. Treatment with G-CSF promoted the recovery of exercise capacity and regeneration of alveolar structural alterations in emphysematous mice. © 2013.

Measurement of the t̄t production cross section in the all-jet final state in pp collisions at √s=7 TeV

A measurement is presented of the t̄t production cross section σt̄t in proton-proton collisions at a centre-of-mass energy of 7 TeV, in the all-jet final state that contains at least six jets, two of which are tagged as originating from b quarks. The data correspond to an integrated luminosity of 3.54 fb-1, collected with the CMS detector at the LHC. The cross section is determined through an unbinned maximum likelihood fit of background and t̄t signal to the reconstructed mass spectrum of t̄t candidates in the data, in which events are subjected to a kinematic fit assuming a t̄t → W+bW-̄b → 6 jets hypothesis. The measurement yields σt̄t = 139±10(stat.)±26(syst.)±3(lum.)pb, a result consistent with those obtained in other t̄t decay channels, as well as with predictions of the standard model. © 2013 CERN for the benefit of the CMS collaboration.

Influence of risk behavior aggregation in different categories of physical activity on the occurrence of cardiovascular risk factors

Background: We aimed to verify the association of risk behavior aggregation in different categories of physical activity (PA) with the presence of cardiovascular risk factors (RF) employees at a public university. Method. We analyzed data of 376 employees, which were visited in their workplace for measurement of weight, height and questionnaires to identify the risk behaviors and risk factors. Chi-square test was used to analyze the association between the dependent and independent variables and binary logistic regression was used to construct a multivariate model for the observed associations. Results: Associations were found between the aggregation of following risk behaviors: smoking, alcohol consumption and physical inactivity, considered in different categories of PA, and the increase in RF, except for the presence of hypertriglyceridemia. Individuals with two or more risk behaviors in occupational PA category are more likely to be hypertensive (3.04 times) and diabetes (3.44 times). For the free time PA category, these individuals were 3.18 times more likely to have hypercholesterolemia and for locomotion PA, more likely to be hypertensive (2.42 times) and obese (2.51 times). Conclusion: There are association between the aggregation of two or more risk behaviors and the presence of cardiovascular RF. © 2013 Bernardo et al.; licensee BioMed Central Ltd.

Measurement of masses in the tt̄ system by kinematic endpoints in pp collisions at √s = 7 TeV

A simultaneous measurement of the top-quark, W-boson, and neutrino masses is reported for tt̄ events selected in the dilepton final state from a data sample corresponding to an integrated luminosity of 5.0 fb-1 collected by the CMS experiment in pp collisions at √s = 7 TeV. The analysis is based on endpoint determinations in kinematic distributions. When the neutrino and W-boson masses are constrained to their world-average values, a top-quark mass value of Mt = 173.9 ± 0.9 (stat)+1.7 -2.1(syst.) GeV is obtained. When such constraints are not used, the three particle masses are obtained in a simultaneous fit. In this unconstrained mode the study serves as a test of mass determination methods that may be used in beyond standard model physics scenarios where several masses in a decay chain may be unknown and undetected particles lead to underconstrained kinematics. © 2013 CERN for the benefit of the CMS collaboration.