String-averaging expectation-maximization for maximum likelihood estimation in emission tomography

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Mechanical behavior of dental implants in different positions in the rehabilitation of the anterior maxilla

Statement of problem. In dental rehabilitations that involve implants, the number of implants is sometimes smaller than the number of lost teeth. This fact can affect the biomechanical behavior and success of the implants.Purpose. The purpose of this study was to investigate the mechanical behavior of different implant positions in the rehabilitation of the anterior maxilla.Material and methods. Three-dimensional models of the maxilla were created based on computed tomography images for 3 different anterior prosthetic rehabilitations. In group IL, the implants were placed in the lateral incisor positions with pontics in the central incisor positions; in group IC, the implants were in the central incisor positions with cantilevers in the lateral incisor positions; and, in group ILIC, one implant was in a lateral incisor position and one was in a central incisor position, with a pontic and a cantilever in the remaining positions. A 150 N load was distributed and applied at the center of the palatal surface of each tooth at a 45-degree angle to the long axis of the tooth. The resulting stress-strain distribution was analyzed for each group.Results. The lowest displacement of the prosthetic structure was observed in group IC, although the same group exhibited the largest displacement of the bone tissue. In the bone tissue, the von Mises stress was mainly observed in the cortical bone in all groups. The maximum value of the von Mises stress shown in the cortical tissue was 35 MPa in the implant that neighbors the cantilever in group ILIC. The maximum von Mises stress in the trabecular bone was 3.5 MPa.Conclusion. The prosthetic configuration of group IC limited the displacement of the prosthetic structure but led to greater displacement of the bone structure. The use of a cantilever increased the stress concentration in the implant and in the bone structure adjacent to the cantilever under the conditions studied here.

Application of passive control to energy harvester efficiency using a nonideal portal frame structural support system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Wide dynamic range homodyne interferometry method and its application for piezoactuator displacement measurements

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The influence of the use of stabilizer bracelet in a child with choreoathetoid cerebral palsy

Introduction: The use of stabilizer bracelet is a frequent treatment for movement disorders to strengthen muscles and adjust coordination. Still questions remain regarding the benefi t of using loads to decrease involuntary movements and the best load and placement. Objective: To measure the infl uence of the stabilizer bracelet on the kinematics and spatiotemporal parameters in planar movements performed by the upper limb. Method: One child, who has the spastic diplegy type of cerebral palsy with choreoathetoid component, and a control child without cerebral palsy, both female and 7 years old, were subjected to analysis of movements in relation to displacement, velocity, linear acceleration, and the calculation of mean square error (MSE) with and without use of stabilizer bracelet with loads of 25, 50, and 75% of the supported maximum load. Results: After comparing data between subjects, a difference was found between patient and control in all situations and variables. An inter-individual comparison using 25% of the maximum load showed the smallest difference with the NDE. Discussion and Conclusion: This therapeutic option is low cost, easy to apply, and does not signifi cantly interfere in the aesthetic of the individual. Therefore, physiotherapists may prescribe this for activities that require greater control of the upper limb because for the case studied the upper limb movement was more effi cient with the use of the stabilizer bracelet.

Sólitons e Oscillons em cenários com violações da simetria de Lorentz

Pós-graduação em Física - FEG

Análise dinâmica de mecanismo articulado de suspensão com não-linearidade na rigidez devido à geometria e à excitação por desbalanceamento rotativo na condição não ideal

Pós-graduação em Engenharia Mecânica - FEB

Zero, minimum and maximum relative radial acceleration for planar formation flight dynamics near triangular libration points in the Earth-Moon system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Modelling the maximum potential of nitrogen deposition and requirements of lysine for broilers

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Reliability of one-repetition maximum test in untrained young adult men and women

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da tenacidade à fratura em juntas soldadas circunferenciais de tubulações de processo

This work aims to analyze the toughness of a welded joint in the presence of a crack through the analysis of maximum tension the material can withstand the presence of this type of defect, since a discontinuity is likely to occur in this type of joint and its detection and its design is simple, using non-destructive testing techniques. The study will be conducted through the CTOD test - Crack-Tip Opening Displacement, with type specimens SE (B) - Single Edge Bend taken from a weld in the L-C position in relation to the length (longitudinal axis) of a test tube. The main idea is to simulate the welding conditions for the manufacture of industrial pipes, made in boiler shops (pipe-shop) within petrochemical plants. These pipes are often subject to operation with flammable and toxic subjected to high pressures and temperatures, where one can break the line can cause irreparable damage to the plant, the environment and the health of surrounding communities. With this study we evaluate whether the weld metal has the same properties as fracture toughness of the base material. This study shows the importance of using a qualified welding procedure for performing quality welds while maintaining the properties of the fracture toughness of the base metal. It was found from the results of tests using a welding procedure described for carrying out welding ensures mechanical properties very close to the base metal, which in terms of design is great, since one can ensure that the weld will the same characteristics of the base metal specified for the assembly of the pipe

Variabilidade entre materiais genéticos de eucalyptus spp quanto à distribuição de raízes finas em latossolos profundos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aplicação de biofertilizante, composto e uréia na produção de capim tanzânia (Panicum maximum, Jacq.) sob irrigação

Pós-graduação em Zootecnia - FCAV

Influence of CAD-CAM diamond bur deterioration on surface roughness and maximum failure load of Y-TZP-based restorations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)