967 resultados para Layer-by-layer methods
Resumo:
Attempts have been made to attain satisfactory network structures in each of the phases of a rubber blend by minimising the cure rate imbalance by employing methods such as grafting of accelerators to the slow curing rubber, chemically bonding the crosslinking agents to the rubber in which it has lower solubility, functionalisation of the slow curing rubber, masterbatching of the curing agents to the slow curing rubber etc. Functionalisation of the slow curing constituents of NR/IIR and NR/EIPDM blends is tried using novel reagents as the first part of this study. However, the crux of the present study is a more direct approach to attaining a covulcanized state in NR/IIR and NR/EPDM blends: Precuring the slow curing rubber (IIR or EPDM) to a low level when it can still blend with NR and then to ck) the final curing after blending with NR. TNM3 precuring is also likely to minimise the viscosity mismatch. Since a low level of resmmal crosslink density is likely to be present lJ1 reclaimed rubbers, blending heat resistant reclaimed rubber such as butyl reclaim with NR may also have the same effect of precuring IIR, and then blending with NR. Hence use of IIR reclaim for developing blends with NR is also proposed to be investigated in this study
Resumo:
Zeolites have established themselves as industrial catalysts for over two decades for a variety of hydrocarbon processing reactions where acidity and shape selectivity are important factors. As solid catalysts, zeolites may be advantageous and superior compared to their homogenous counterparts due to their characteristic properties. It is only in recent years that the utility of zeolites for organic synthesis is recognized for producing specific organic intermediates and fine chemicals in high selectivity. In this thesis an attempt has been made to compare the catalytic activity of some medium and large pore zeolites in a few alkylation and acylation reactions. The work reported in the present study is basically centered around the following zeolites namely, ZSM-5, mordenite, zeolite Y and beta. The major reactions carried out were benzoylation of o-xylene, propionylation of toluene and anisole and benzylation of oxylene. . The programme involves the synthesis, modifications and characterization of the zeolite catalysts by various methods. The influence of various parameters such as non-framework cations, Si/Al ratio of zeolites, temperature of the reaction, catalyst concentration, molar ratio of the reactants and recycling of the catalysts were also examined upon the conversion of reactants and the formation of the desired products in the alkylation/ acylation reactions. The general conclusions drawn by us from the results obtained are summarized in the last chapter of the thesis. Zeolite beta ofi'ers interesting opportunities as a potential catalyst in alkylation reactions and the area of catalysis by medium and large pore zeolites is very fascinating and there is plenty of scope for further research in this field. Moreover, zeolite based catalysts are effective in meeting current industrial processing and more stringent environment pollution limits.
Resumo:
The objective of the study was to find out a natural way to fight white spot syndrome virus (WSSV) in cultured shrimps, as the present scenario necessitated an organic remedy for the devastating pathogen in crustaceans. Under this research programme seven mangrove plants were collected, identified and aqueous extracts screened for their protective effect on the giant tiger shrimp Penaeus monodon against WSSV. The experimental design consisted two modes of application, such as exposure of the virus to the extract and injection challenge, and oral administration of the extract coated feed followed by oral challenge. All experimental animals were monitored through a nested diagnostic PCR analysis. Of the seven mangrove extracts screened aqueous extract from Ceriops tagal imparted total protection to shrimp from WSSV when challenged by both methods. Shrimps administered with the aqueous extract from C. tagal were devoid of virions. The HPLC fingerprint of the aqueous extracts from C. tagal showed more than 25 peaks and 7 of them were larger and well separated. Preliminary phytochemical analysis revealed the presence of alkaloids, flavonoids, polyphenolics, cardiac glycosides, saponins and sterols. The study indicated suitability of the aqueous extract of C. tagal as a possible prophylaxis for WSSV infection in shrimp. This is the first report on the anti WSSV property of the mangrove plant C. tagal
Resumo:
Polyaniline and oligomeric cobalt phthalocyanine are blended in different proportions by chemical methods. These blends are characterised by spectroscopic methods and dielectric measurements. Dielectric studies on the conducting polymer blends are carried out in the frequency range of 100 kHz to 5MHz from room temperature (300 K) to 373 K. Dielectric permittivity and dielectric loss of these blends are explained on the basis of interfacial polarisation. From the dielectric permittivity studies, ac conductivity of the samples were calculated and the results are correlated. In order to understand the exact conduction mechanism of the samples, dc electrical conductivity of the blends is carried out in the temperature range of 70–300 K. By applying Mott’s theory, it is found that the conducting polymer composites obey a 3D variable range hopping mechanism. The values of Mott’s temperature (T0), density of states at the Fermi energy (N(EF)), range of hopping (R) and hopping energy (W) for the composites are calculated and presented
Resumo:
The objective of the study was to find out a natural way to fight white spot syndrome virus (WSSV) in cultured shrimps, as the present scenario necessitated an organic remedy for the devastating pathogen in crustaceans. Under this research programme seven mangrove plants were collected, identified and aqueous extracts screened for their protective effect on the giant tiger shrimp Penaeus monodon against WSSV. The experimental design consisted two modes of application, such as exposure of the virus to the extract and injection challenge, and oral administration of the extract coated feed followed by oral challenge. All experimental animals were monitored through a nested diagnostic PCR analysis. Of the seven mangrove extracts screened aqueous extract from Ceriops tagal imparted total protection to shrimp from WSSV when challenged by both methods. Shrimps administered with the aqueous extract from C. tagal were devoid of virions. The HPLC fingerprint of the aqueous extracts from C. tagal showed more than 25 peaks and 7 of them were larger and well separated. Preliminary phytochemical analysis revealed the presence of alkaloids, flavonoids, polyphenolics, cardiac glycosides, saponins and sterols. The study indicated suitability of the aqueous extract of C. tagal as a possible prophylaxis for WSSV infection in shrimp. This is the first report on the anti WSSV property of the mangrove plant C. tagal
Resumo:
The present study is the first attempt to understand population characteristics of the deep-sea pandalid shrimp, P. quasigrandis and to assess the status of these resources off Kerala coast.Total mortality coefficient (Z) of P. quasigrandis estimated by various methods.Natural mortality coefficient (M) calculated was 0.65 and 1.02 by Pauly‟sempirical formula and Srinaths‟s formula respectively The deep-sea shrimp P. quasigrandis exploited from the present fishing ground and their monetary return has started showing a declining trend. By observing the current yield and economic return, there is no further scope for increasing the catch from the present fishing ground. The study indicated that majority of the deep-sea shrimp trawlers, especially targeted for pandalid shrimps still concentrated off Kollam area (Quilon Bank). Even though researchers had located several potential deep-sea fishing grounds based on exploratory surveys in Indian EEZ , fishermen are unaware of these fishing grounds located and hence sharing the information about new potential deep-sea fishing grounds could avert the possible stock decline due to the intensive targeted deep-sea shrimp fishery in the Quilon Bank. Hence, the present study recommended that part of the effort from existing fishing grounds may be shifted to newly located deep-sea fishing grounds which will help in a sustainableexploitation of deep-sea resources off Kerala coast.
Resumo:
Cochin estuarine system is among the most productive aquatic environment along the Southwest coast of India, exhibits unique ecological features and possess greater socioeconomic relevance. Serious investigations carried out during the past decades on the hydro biogeochemical variables pointed out variations in the health and ecological functioning of this ecosystem. Characterisation of organic matter in the estuary has been attempted in many investigations. But detailed studies covering the degradation state of organic matter using molecular level approach is not attempted. The thesis entitled Provenance, Isolation and Characterisation of Organic Matter in the Cochin Estuarine Sediment-“ A Diagenetic Amino Acid Marker Scenario” is an integrated approach to evaluate the source, quantity, quality, and degradation state of the organic matter in the surface sediments of Cochin estuarine system with the combined application of bulk and molecular level tools. Sediment and water samples from nine stations situated at Cochin estuary were collected in five seasonal sampling campaigns, for the biogeochemical assessment and their distribution pattern of sedimentary organic matter. The sampling seasons were described and abbreviated as follows: April- 2009 (pre monsoon: PRM09), August-2009 (monsoon: MON09), January-2010 (post monsoon: POM09), April-2010 (pre monsoon: PRM10) and September- 2012 (monsoon: MON12). In order to evaluate the general environmental conditions of the estuary, water samples were analysed for water quality parameters, chlorophyll pigments and nutrients by standard methods. Investigations suggested the fact that hydrographical variables and nutrients in Cochin estuary supports diverse species of flora and fauna. Moreover the sedimentary variables such as pH, Eh, texture, TOC, fractions of nitrogen and phosphorous were determined to assess the general geochemical setting as well as redox status. The periodically fluctuating oxic/ anoxic conditions and texture serve as the most significant variables controlling other variables of the aquatic environment. The organic matter in estuary comprise of a complex mixture of autochthonous as well as allochthonous materials. Autochthonous input is limited or enhanced by the nutrient elements like N and P (in their various fractions), used as a tool to evaluate their bioavailability. Bulk parameter approach like biochemical composition, stoichiometric elemental ratios and stable carbon isotope ratio was also employed to assess the quality and quantity of sedimentary organic matter in the study area. Molecular level charactersation of free sugars and amino acids were carried out by liquid chromatographic techniques. Carbohydrates are the products of primary production and their occurrence in sediments as free sugars can provide information on the estuarine productivity. Amino acid biogeochemistry provided implications on the system productivity, nature of organic matter as well as degradation status of the sedimentary organic matter in the study area. The predominance of carbohydrates over protein indicated faster mineralisation of proteinaceous organic matter in sediments and the estuary behaves as a detrital trap for the accumulation of aged organic matter. The higher lipid content and LPD/CHO ratio pointed towards the better food quality that supports benthic fauna and better accumulation of lipid compounds in the sedimentary environment. Allochthonous addition of carbohydrates via terrestrial run off was responsible for the lower PRT/CHO ratio estimated in thesediments and the lower ratios also denoted a detrital heterotrophic environment. Biopolymeric carbon and the algal contribution to BPC provided important information on the better understanding the trophic state of the estuarine system and the higher values of chlorophyll-a to phaeophytin ratio indicated deposition of phytoplankton to sediment at a rapid rate. The estimated TOC/TN ratios implied the combined input of both terrestrial and autochthonous organic matter to sedimentsAmong the free sugars, depleted levels of glucose in sediments in most of the stations and abundance of mannose at station S5 was observed during the present investigation. Among aldohexoses, concentration of galactose was found to be higher in most of the stationsRelative abundance of AAs in the estuarine sediments based on seasons followed the trend: PRM09-Leucine > Phenylalanine > Argine > Lysine, MON09-Lysine > Aspartic acid > Histidine > Tyrosine > Phenylalanine, POM09-Lysine > Histadine > Phenyalanine > Leucine > Methionine > Serine > Proline > Aspartic acid, PRM10-Valine > Aspartic acid > Histidine > Phenylalanine > Serine > Proline, MON12-Lysine > Phenylalanine > Aspartic acid > Histidine > Valine > Tyrsine > MethionineThe classification of study area into three zones based on salinity was employed in the present study for the sake of simplicity and generalized interpretations. The distribution of AAs in the three zones followed the trend: Fresh water zone (S1, S2):- Phenylalanine > Lysine > Aspartic acid > Methionine > Valine ῀ Leucine > Proline > Histidine > Glycine > Serine > Glutamic acid > Tyrosine > Arginine > Alanine > Threonine > Cysteine > Isoleucine. Estuarine zone (S3, S4, S5, S6):- Lysine > Aspartic acid > Phenylalanine > Leucine > Valine > Histidine > Methionine > Tyrosine > Serine > Glutamic acid > Proline > Glycine > Arginine > Alanine > Isoleucine > Cysteine > Threonine. Riverine /Industrial zone (S7, S8, S9):- Phenylalanine > Lysine > Aspartic acid > Histidine > Serine > Arginine > Tyrosine > Leucine > Methionine > Glutamic acid > Alanine > Glycine > Cysteine > Proline > Isoleucine > Threonine > Valine. The abundance of AAs like glutamic acid, aspartic acid, isoleucine, valine, tyrosine, and phenylalanine in sediments of the study area indicated freshly derived organic matter.
Resumo:
Pollution of water with pesticides has become a threat to the man, material and environment. The pesticides released to the environment reach the water bodies through run off. Industrial wastewater from pesticide manufacturing industries contains pesticides at higher concentration and hence a major source of water pollution. Pesticides create a lot of health and environmental hazards which include diseases like cancer, liver and kidney disorders, reproductive disorders, fatal death, birth defects etc. Conventional wastewater treatment plants based on biological treatment are not efficient to remove these compounds to the desired level. Most of the pesticides are phyto-toxic i.e., they kill the microorganism responsible for the degradation and are recalcitrant in nature. Advanced oxidation process (AOP) is a class of oxidation techniques where hydroxyl radicals are employed for oxidation of pollutants. AOPs have the ability to totally mineralise the organic pollutants to CO2 and water. Different methods are employed for the generation of hydroxyl radicals in AOP systems. Acetamiprid is a neonicotinoid insecticide widely used to control sucking type insects on crops such as leafy vegetables, citrus fruits, pome fruits, grapes, cotton, ornamental flowers. It is now recommended as a substitute for organophosphorous pesticides. Since its use is increasing, its presence is increasingly found in the environment. It has high water solubility and is not easily biodegradable. It has the potential to pollute surface and ground waters. Here, the use of AOPs for the removal of acetamiprid from wastewater has been investigated. Five methods were selected for the study based on literature survey and preliminary experiments conducted. Fenton process, UV treatment, UV/ H2O2 process, photo-Fenton and photocatalysis using TiO2 were selected for study. Undoped TiO2 and TiO2 doped with Cu and Fe were prepared by sol-gel method. Characterisation of the prepared catalysts was done by X-ray diffraction, scanning electron microscope, differential thermal analysis and thermogravimetric analysis. Influence of major operating parameters on the removal of acetamiprid has been investigated. All the experiments were designed using central compoiste design (CCD) of response surface methodology (RSM). Model equations were developed for Fenton, UV/ H2O2, photo-Fenton and photocatalysis for predicting acetamiprid removal and total organic carbon (TOC) removal for different operating conditions. Quality of the models were analysed by statistical methods. Experimental validations were also done to confirm the quality of the models. Optimum conditions obtained by experiment were verified with that obtained using response optimiser. Fenton Process is the simplest and oldest AOP where hydrogen peroxide and iron are employed for the generation of hydroxyl radicals. Influence of H2O2 and Fe2+ on the acetamiprid removal and TOC removal by Fenton process were investigated and it was found that removal increases with increase in H2O2 and Fe2+ concentration. At an initial concentration of 50 mg/L acetamiprid, 200 mg/L H2O2 and 20 mg/L Fe2+ at pH 3 was found to be optimum for acetamiprid removal. For UV treatment effect of pH was studied and it was found that pH has not much effect on the removal rate. Addition of H2O2 to UV process increased the removal rate because of the hydroxyl radical formation due to photolyis of H2O2. An H2O2 concentration of 110 mg/L at pH 6 was found to be optimum for acetamiprid removal. With photo-Fenton drastic reduction in the treatment time was observed with 10 times reduction in the amount of reagents required. H2O2 concentration of 20 mg/L and Fe2+ concentration of 2 mg/L was found to be optimum at pH 3. With TiO2 photocatalysis improvement in the removal rate was noticed compared to UV treatment. Effect of Cu and Fe doping on the photocatalytic activity under UV light was studied and it was observed that Cu doping enhanced the removal rate slightly while Fe doping has decreased the removal rate. Maximum acetamiprid removal was observed for an optimum catalyst loading of 1000 mg/L and Cu concentration of 1 wt%. It was noticed that mineralisation efficiency of the processes is low compared to acetamiprid removal efficiency. This may be due to the presence of stable intermediate compounds formed during degradation Kinetic studies were conducted for all the treatment processes and it was found that all processes follow pseudo-first order kinetics. Kinetic constants were found out from the experimental data for all the processes and half lives were calculated. The rate of reaction was in the order, photo- Fenton>UV/ H2O2>Fenton> TiO2 photocatalysis>UV. Operating cost was calculated for the processes and it was found that photo-Fenton removes the acetamiprid at lowest operating cost in lesser time. A kinetic model was developed for photo-Fenton process using the elementary reaction data and mass balance equations for the species involved in the process. Variation of acetamiprid concentration with time for different H2O2 and Fe2+ concentration at pH 3 can be found out using this model. The model was validated by comparing the simulated concentration profiles with that obtained from experiments. This study established the viability of the selected AOPs for the removal of acetamiprid from wastewater. Of the studied AOPs photo- Fenton gives the highest removal efficiency with lowest operating cost within shortest time.
Resumo:
Salient pole brushless alternators coupled to IC engines are extensively used as stand-by power supply units for meeting in- dustrial power demands. Design of such generators demands high power to weight ratio, high e ciency and low cost per KVA out- put. Moreover, the performance characteristics of such machines like voltage regulation and short circuit ratio (SCR) are critical when these machines are put into parallel operation and alterna- tors for critical applications like defence and aerospace demand very low harmonic content in the output voltage. While designing such alternators, accurate prediction of machine characteristics, including total harmonic distortion (THD) is essential to mini- mize development cost and time. Total harmonic distortion in the output voltage of alternators should be as low as possible especially when powering very sophis- ticated and critical applications. The output voltage waveform of a practical AC generator is replica of the space distribution of the ux density in the air gap and several factors such as shape of the rotor pole face, core saturation, slotting and style of coil disposition make the realization of a sinusoidal air gap ux wave impossible. These ux harmonics introduce undesirable e ects on the alternator performance like high neutral current due to triplen harmonics, voltage distortion, noise, vibration, excessive heating and also extra losses resulting in poor e ciency, which in turn necessitate de-rating of the machine especially when connected to non-linear loads. As an important control unit of brushless alternator, the excitation system and its dynamic performance has a direct impact on alternator's stability and reliability. The thesis explores design and implementation of an excitation i system utilizing third harmonic ux in the air gap of brushless al- ternators, using an additional auxiliary winding, wound for 1=3rd pole pitch, embedded into the stator slots and electrically iso- lated from the main winding. In the third harmonic excitation system, the combined e ect of two auxiliary windings, one with 2=3rd pitch and another third harmonic winding with 1=3rd pitch, are used to ensure good voltage regulation without an electronic automatic voltage regulator (AVR) and also reduces the total harmonic content in the output voltage, cost e ectively. The design of the third harmonic winding by analytic methods demands accurate calculation of third harmonic ux density in the air gap of the machine. However, precise estimation of the amplitude of third harmonic ux in the air gap of a machine by conventional design procedures is di cult due to complex geome- try of the machine and non-linear characteristics of the magnetic materials. As such, prediction of the eld parameters by conven- tional design methods is unreliable and hence virtual prototyping of the machine is done to enable accurate design of the third har- monic excitation system. In the design and development cycle of electrical machines, it is recognized that the use of analytical and experimental methods followed by expensive and in exible prototyping is time consum- ing and no longer cost e ective. Due to advancements in com- putational capabilities over recent years, nite element method (FEM) based virtual prototyping has become an attractive al- ternative to well established semi-analytical and empirical design methods as well as to the still popular trial and error approach followed by the costly and time consuming prototyping. Hence, by virtually prototyping the alternator using FEM, the important performance characteristics of the machine are predicted. Design of third harmonic excitation system is done with the help of results obtained from virtual prototype of the machine. Third harmonic excitation (THE) system is implemented in a 45 KVA ii experimental machine and experiments are conducted to validate the simulation results. Simulation and experimental results show that by utilizing third harmonic ux in the air gap of the ma- chine for excitation purposes during loaded conditions, triplen harmonic content in the output phase voltage is signi cantly re- duced. The prototype machine with third harmonic excitation system designed and developed based on FEM analysis proved to be economical due to its simplicity and has the added advan- tage of reduced harmonics in the output phase voltage.
Resumo:
For the theoretical investigation of local phenomena (adsorption at surfaces, defects or impurities within a crystal, etc.) one can assume that the effects caused by the local disturbance are only limited to the neighbouring particles. With this model, that is well-known as cluster-approximation, an infinite system can be simulated by a much smaller segment of the surface (Cluster). The size of this segment varies strongly for different systems. Calculations to the convergence of bond distance and binding energy of an adsorbed aluminum atom on an Al(100)-surface showed that more than 100 atoms are necessary to get a sufficient description of surface properties. However with a full-quantummechanical approach these system sizes cannot be calculated because of the effort in computer memory and processor speed. Therefore we developed an embedding procedure for the simulation of surfaces and solids, where the whole system is partitioned in several parts which itsself are treated differently: the internal part (cluster), which is located near the place of the adsorbate, is calculated completely self-consistently and is embedded into an environment, whereas the influence of the environment on the cluster enters as an additional, external potential to the relativistic Kohn-Sham-equations. The basis of the procedure represents the density functional theory. However this means that the choice of the electronic density of the environment constitutes the quality of the embedding procedure. The environment density was modelled in three different ways: atomic densities; of a large prepended calculation without embedding transferred densities; bulk-densities (copied). The embedding procedure was tested on the atomic adsorptions of 'Al on Al(100) and Cu on Cu(100). The result was that if the environment is choices appropriately for the Al-system one needs only 9 embedded atoms to reproduce the results of exact slab-calculations. For the Cu-system first calculations without embedding procedures were accomplished, with the result that already 60 atoms are sufficient as a surface-cluster. Using the embedding procedure the same values with only 25 atoms were obtained. This means a substantial improvement if one takes into consideration that the calculation time increased cubically with the number of atoms. With the embedding method Infinite systems can be treated by molecular methods. Additionally the program code was extended by the possibility to make molecular-dynamic simulations. Now it is possible apart from the past calculations of fixed cores to investigate also structures of small clusters and surfaces. A first application we made with the adsorption of Cu on Cu(100). We calculated the relaxed positions of the atoms that were located close to the adsorption site and afterwards made the full-quantummechanical calculation of this system. We did that procedure for different distances to the surface. Thus a realistic adsorption process could be examined for the first time. It should be remarked that when doing the Cu reference-calculations (without embedding) we begun to parallelize the entire program code. Only because of this aspect the investigations for the 100 atomic Cu surface-clusters were possible. Due to the good efficiency of both the parallelization and the developed embedding procedure we will be able to apply the combination in future. This will help to work on more these areas it will be possible to bring in results of full-relativistic molecular calculations, what will be very interesting especially for the regime of heavy systems.
Resumo:
Land use is a crucial link between human activities and the natural environment and one of the main driving forces of global environmental change. Large parts of the terrestrial land surface are used for agriculture, forestry, settlements and infrastructure. Given the importance of land use, it is essential to understand the multitude of influential factors and resulting land use patterns. An essential methodology to study and quantify such interactions is provided by the adoption of land-use models. By the application of land-use models, it is possible to analyze the complex structure of linkages and feedbacks and to also determine the relevance of driving forces. Modeling land use and land use changes has a long-term tradition. In particular on the regional scale, a variety of models for different regions and research questions has been created. Modeling capabilities grow with steady advances in computer technology, which on the one hand are driven by increasing computing power on the other hand by new methods in software development, e.g. object- and component-oriented architectures. In this thesis, SITE (Simulation of Terrestrial Environments), a novel framework for integrated regional sland-use modeling, will be introduced and discussed. Particular features of SITE are the notably extended capability to integrate models and the strict separation of application and implementation. These features enable efficient development, test and usage of integrated land-use models. On its system side, SITE provides generic data structures (grid, grid cells, attributes etc.) and takes over the responsibility for their administration. By means of a scripting language (Python) that has been extended by language features specific for land-use modeling, these data structures can be utilized and manipulated by modeling applications. The scripting language interpreter is embedded in SITE. The integration of sub models can be achieved via the scripting language or by usage of a generic interface provided by SITE. Furthermore, functionalities important for land-use modeling like model calibration, model tests and analysis support of simulation results have been integrated into the generic framework. During the implementation of SITE, specific emphasis was laid on expandability, maintainability and usability. Along with the modeling framework a land use model for the analysis of the stability of tropical rainforest margins was developed in the context of the collaborative research project STORMA (SFB 552). In a research area in Central Sulawesi, Indonesia, socio-environmental impacts of land-use changes were examined. SITE was used to simulate land-use dynamics in the historical period of 1981 to 2002. Analogous to that, a scenario that did not consider migration in the population dynamics, was analyzed. For the calculation of crop yields and trace gas emissions, the DAYCENT agro-ecosystem model was integrated. In this case study, it could be shown that land-use changes in the Indonesian research area could mainly be characterized by the expansion of agricultural areas at the expense of natural forest. For this reason, the situation had to be interpreted as unsustainable even though increased agricultural use implied economic improvements and higher farmers' incomes. Due to the importance of model calibration, it was explicitly addressed in the SITE architecture through the introduction of a specific component. The calibration functionality can be used by all SITE applications and enables largely automated model calibration. Calibration in SITE is understood as a process that finds an optimal or at least adequate solution for a set of arbitrarily selectable model parameters with respect to an objective function. In SITE, an objective function typically is a map comparison algorithm capable of comparing a simulation result to a reference map. Several map optimization and map comparison methodologies are available and can be combined. The STORMA land-use model was calibrated using a genetic algorithm for optimization and the figure of merit map comparison measure as objective function. The time period for the calibration ranged from 1981 to 2002. For this period, respective reference land-use maps were compiled. It could be shown, that an efficient automated model calibration with SITE is possible. Nevertheless, the selection of the calibration parameters required detailed knowledge about the underlying land-use model and cannot be automated. In another case study decreases in crop yields and resulting losses in income from coffee cultivation were analyzed and quantified under the assumption of four different deforestation scenarios. For this task, an empirical model, describing the dependence of bee pollination and resulting coffee fruit set from the distance to the closest natural forest, was integrated. Land-use simulations showed, that depending on the magnitude and location of ongoing forest conversion, pollination services are expected to decline continuously. This results in a reduction of coffee yields of up to 18% and a loss of net revenues per hectare of up to 14%. However, the study also showed that ecological and economic values can be preserved if patches of natural vegetation are conservated in the agricultural landscape. -----------------------------------------------------------------------
Resumo:
Im Rahmen der Fallstudie Harz sollte an der Schnittstelle zwischen Grundlagenforschung und angewandter Forschung ein Beitrag zur Klärung der Frage geleistet werden, inwieweit zwei Zuläufe der Sösetalsperre im Westharz versauert bzw. versauerungsgefährdet sind; aus diesem Stausee wird Trinkwasser für mehrere Gemeinden in Norddeutschland gewonnen. Die Belastung des fast vollständig bewaldeten Einzugsgebiets der Sösetalsperre mit luftbürtigen Schadstoffen (Saurer Regen) zählte zu den höchsten in Mitteleuropa. An jeweils drei Untersuchungsstellen der beiden Bäche Alte Riefensbeek (R1 bis R3) und Große Söse (S1 bis S3) wurden zwischen März 1987 und November 1988 Proben aus Moospolstern und dem hyporheischen Interstitial entnommen und physikalisch, chemisch und biologisch untersucht. Ergänzend wurden Wasserproben zwischen März 1986 und Oktober 1991 sowie vom April 1998 ebenso wie qualitative Fänge von Makroinvertebraten zwischen November 1986 und Juli 1990 sowie vom April 1998 ausgewertet. Die Analyse der tierischen Besiedlung der Moos- und Interstitialproben beschränkte sich auf die taxonomischen Gruppen Turbellaria (Strudelwürmer), Mollusca (Weichtiere), Amphipoda (Flohkrebse), Ephemeroptera (Eintagsfliegen), Plecoptera (Steinfliegen), Heteroptera (Wanzen), Megaloptera (Schlammfliegen), Coleoptera (Käfer), Trichoptera (Köcherfliegen) und Diptera (Zweiflügler). Der Grundsatz, daß normalverteilte und nicht normalverteilte Daten statistisch unterschiedlich behandelt werden müssen, wurde konsequent angewandt. Am Beispiel der Choriotopstruktur wurde gezeigt, daß die Auswahl des Analyseverfahrens das Ergebnis der ökologischen Interpretation multivariater statistischer Auswertung beeinflußt. Die Daten der Korngrößen-Verteilung wurden vergleichend einer univariaten und einer multivariaten statistischen Analyse unterworfen. Mit dem univariaten Verfahren wurden die Gradienten der ökologisch relevanten Korngrößen-Parameter eher erkannt als mit dem multivariaten Verfahren. Die Auswirkungen von Gewässerversauerung sowie anderer Umweltfaktoren (insgesamt 42 Faktoren) auf die Lebensgemeinschaften wurden anhand der Parameter Artenzahl, Besiedlungsdichte, Körpergröße und Biomasse untersucht. Abundanz, Biomasse und Körpergröße sowie die Umweltfaktoren wurden auf einem horizontalen Gradienten, d.h. im Längslauf der Bäche, und auf einem vertikalen Gradienten, d.h. fließende Welle / Bryorheon / Benthon versus Hyporheon, untersucht. Es wurde ein terminologisches System für die Kompartimente in der Fließgewässer-Aue vorgeschlagen, das in sich einheitlich ist. Es wurde ein neuer Moos-Vitalitätsindex für die Moospolster vorgestellt. Es wurden Bestimmungsschlüssel für die Larven der Chloroperlidae (Steinfliegen-Familie) und der Empididae (Tanzfliegen) in den beiden Harzbächen entwickelt. Die untersuchten Bachstrecken waren frei von Abwasserbelastung. An zwei Stellen wurde Wasser für einen Forellenteich ausgeleitet. Abgesehen von zwei meterhohen Abstürzen in der Großen Söse waren wasserbauliche Veränderungen ohne große Bedeutung. Das Abfluß-Regime war insofern nicht mehr natürlich, als beide Bäche in das System der bergbaulichen Bewässerungsgräben des Oberharzes eingebunden sind. Die Söse hatte ein F-nivopluviales Abfluß-Regime, der abflußreichste Doppelmonat war der März / April, die Unregelmäßigkeit des Abfluß-Regimes war sehr hoch, die Vorhersagbarkeit sehr niedrig, die monatlichen Abfluß-Maxima wiesen eine sehr geringe Konstanz auf. Der Zeitraum der biologischen Probenahme wurde von überdurchschnittlich vielen Tagen mit mäßig erhöhten Abflüssen geprägt, sehr große Hochwasser-Wellen fehlten aber. Die Abfluß-Dynamik wurde statistisch beschrieben. Das hydraulische Regime wurde anhand der Meßgrößen Fließgeschwindigkeit, Fließkraft und FROUDE-Zahl dargestellt. Der Zusammenhang zwischen Abfluß und Fließgeschwindigkeit auf der einen Seite und der Korngrößen-Verteilung auf der anderen Seite wurde statistisch untersucht, ebenfalls zwischen dem Abfluß und dem Kohlenstoff- und Stickstoff-Gehalt der Feinstpartikel sowie dem Wasserchemismus. In den Phasen ohne Hochwasser hatte das Hyporheal die Funktion einer Senke für Feinstkörner. Das Bachbett der Alten Riefensbeek war stabiler als das der Großen Söse. Insgesamt gesehen war das hyporheische Sediment in den quellnahen Abschnitten grobkörniger und auf den quellfernen Strecken feinkörniger. Der prozentuale Anteil der Feinstkörner im Hyporheal und Benthal nahm aber im Längslauf der Bäche ab. Dies ist ungewöhnlich, konnte aber nicht plausibel mit geologischen und hydrologischen Meßgrößen erklärt werden. Beide Bäche waren sommerkalt. Der Einfluß der Wassertemperatur auf die Larvalentwicklung wurde beispielhaft an den Taxa Baetis spp. und Leuctra gr. inermis untersucht. Es gab eine Tendenz, daß der Kohlenstoff- und Stickstoff-Gehalt der Feinstpartikel vom Benthal in das Hyporheal anstieg. Dies war ein weiterer Hinweis darauf, daß das Hyporheal die Funktion einer Senke und Vorratskammer für Nährstoffe hat. Der Zusammenhang zwischen partikulärer und gelöster Kohlenstoff-Fraktion wurde diskutiert. Im Hyporheon war die Nitrifikation nicht stärker als in der fließenden Welle. Es gab Hinweise, daß die sauren pH-Werte in der Großen Söse die Nitrifikation hemmten. Die Valenzen der Moos- und Tier-Taxa bezüglich Fließgeschwindigkeit, pH-Wert, Alkalinität sowie der Gehalte von Sauerstoff, Calcium, Magnesium, Kalium und Natrium wurden zusammengestellt. Das hyporheische Sediment war sehr grob und hatte eine hohe Porosität. Der Austausch zwischen fließender Welle und hyporheischem Wasser konnte deshalb sehr schnell erfolgen, es gab keine intergranulare Sprungschicht, die physikalischen und chemischen Tiefengradienten waren in den meisten Fällen gar nicht ausgeprägt oder nur sehr flach. Die Wassertemperatur des Freiwassers unterschied sich nicht signifikant von derjenigen im hyporheischen Wasser. Es gab -- von wenigen Ausnahmen bei pH-Wert, Leitfähigkeit und Sauerstoffgehalt abgesehen -- keine signifikanten Unterschiede zwischen dem Wasserchemismus der fließenden Welle und dem des Hyporheals. Die physikalischen und chemischen Voraussetzungen für die Refugialfunktion des Hyporheons waren deshalb für versauerungsempfindliche Taxa nicht gegeben. In der Tiefenverteilung der untersuchten Tiergruppen im Hyporheal lag das Maximum der Abundanz bzw. Biomasse häufiger in 10 cm als in 30 cm Tiefe. Daraus läßt sich aber keine allgemeine Gesetzmäßigkeit ableiten. Es wurde durchgehend die Definition angewendet, daß die Gewässerversauerung durch den Verlust an Pufferkapazität charakterisiert ist. Saure Gewässer können, müssen aber nicht versauert sein; versauerte Gewässer können, müssen aber nicht saures Wasser haben. Maßstab für das Pufferungsvermögen eines Gewässers ist nicht der pH-Wert, sondern sind die Alkalinität und andere chemische Versauerungsparameter. Der pH-Wert war auch operativ nicht als Indikator für Gewässerversauerung anwendbar. Die chemische Qualität des Bachwassers der Großen Söse entsprach aufgrund der Versauerung nicht den umweltrechtlichen Vorgaben bezüglich der Parameter pH-Wert, Aluminium, Eisen und Mangan, bzgl. Zink galt dies nur an S1. In der Alten Riefensbeek genügte das Hyporheal-Wasser in 30 cm Tiefe an R2 bzgl. des Sauerstoff-Gehalts nicht den umweltrechtlichen Anforderungen. Nur im Freiwasser an R1 genügten die Ammonium-Werte den Vorgaben der EG-Fischgewässer-Richtlinie, der Grenzwert wurde an allen anderen Meßstellen und Entnahmetiefen überschritten. Das BSB-Regime in allen Entnahmetiefen an R2, im Freiwasser an R3 und S1, im Hyporheal an R1 sowie in 30 cm Tiefe an R3 genügte nicht den Anforderungen der Fischgewässer-Richtlinie. Der Grenzwert für Gesamt-Phosphor wurde an S3 überschritten. In der Großen Söse war der Aluminium-Gehalt so hoch, daß anorganisches und organisches Aluminium unterschieden werden konnten. Besonders hohe Gehalte an toxischem anorganischen Aluminium wurden an Tagen mit Spitzen-Abflüssen und Versauerungsschüben gemessen. Erst die Ermittlung verschiedener chemischer Versauerungsparameter zeigte, daß auch die alkalischen Probestellen R2 und R3 mindestens versauerungsempfindlich waren. Die Messung bzw. Berechnung von chemischen Versauerungsparametern sollte deshalb zum Routineprogramm bei der Untersuchung von Gewässerversauerung gehören. Zu Beginn des Untersuchungsprogramms war angenommen worden, daß die mittleren und unteren Abschnitte der Alten Riefensbeek unversauert sind. Dieser Ansatz des Untersuchungsprogramms, einen unversauerten Referenzbach (Alte Riefensbeek) mit einem versauerten Bach (Große Söse) zu vergleichen, mußte nach der Berechnung von chemischen Versauerungsindikatoren sowie der Analyse der Abundanz- und Biomasse-Werte modifiziert werden. Es gab einen Versauerungsgradienten entlang der Probestellen: R1 (unversauert) R2 und R3 (versauerungsempfindlich bis episodisch leicht versauert) S2 und S3 (dauerhaft versauert) S1 (dauerhaft stark versauert). An S1 war das Hydrogencarbonat-Puffersystem vollständig, an S2 und S3 zeitweise ausgefallen. Die Versauerungslage an R2 und R3 war also schlechter als vorausgesehen. Unterschiede im Versauerungsgrad zwischen den Meßstellen waren nicht so sehr in unterschiedlichen Eintragsraten von versauernden Stoffen aus der Luft begründet, sondern in unterschiedlichen Grundgesteinen mit unterschiedlichem Puffervermögen. Der Anteil der verschiedenen sauren Anionen an der Versauerung wurde untersucht, die chemischen Versauerungsmechanismen wurden mit Hilfe von Ionenbilanzen und verschiedenen Versauerungsquotienten analysiert. Die beiden untersuchten Bäche waren von anthropogener Versauerung betroffen. Dabei spielte die Schwefel-Deposition (Sulfat) eine größere Rolle als die Stickstoff-Deposition (Nitrat). Die Probestelle S1 war immer schon in unbekanntem Maß natürlich sauer. Dieser natürlich saure Zustand wurde von der hinzugekommenen anthropogenen Versauerung bei weitem überragt. Die wenigen gewässerökologischen Daten, die im Wassereinzugsgebiet der Söse vor 1986 gewonnen wurden, deuten darauf hin, daß die Versauerung in den 70er und in der ersten Hälfte der 80er Jahre vom Boden und Gestein in die Bäche durchgeschlagen war. Dieser Versauerungsprozeß begann vermutlich vor 1973 in den Quellen auf dem Acker-Bruchberg und bewegte sich im Laufe der Jahre immer weiter talwärts in Richtung Trinkwasser-Talsperre. Der Mangel an (historischen) freilandökologischen Grundlagendaten war nicht nur im Untersuchungsgebiet, sondern ist allgemein in der Versauerungsforschung ein Problem. Wenn sich das Vorkommen von nah verwandten Arten (weitgehend) ausschließt, kann dies an der Versauerung liegen, z.B. war die Alte Riefensbeek ein Gammarus-Bach, die Große Söse ein Niphargus-Bach; dieses muß aber nicht an der Versauerung liegen, z.B. fehlte Habroleptoides confusa im Hyporheos an R3, Habrophlebia lauta hatte dagegen ihr Abundanz- und Biomasse-Maximum an R3. Zugleich lag das Maximum des prozentualen Anteils von Grobsand an R3, eine mögliche Ursache für diese interspezifische Konkurrenz. Die biologische Indikation von Gewässerversauerung mit Hilfe der Säurezustandsklassen funktionierte nicht in den beiden Harzbächen. Es wurde deshalb ein biologischer Versauerungsindex vorgeschlagen; dieser wurde nicht am pH-Wert kalibriert, sondern an der chemischen Versauerungslage, gekennzeichnet durch die Alkalinität und andere chemische Meßgrößen der Versauerung. Dafür wurden aufgrund der qualitativen und quantitativen Daten die häufigeren Taxa in die vier Klassen deutlich versauerungsempfindlich, mäßig versauerungsempfindlich, mäßig versauerungstolerant und deutlich versauerungstolerant eingeteilt. Es reicht nicht aus, die biologischen Folgen von Gewässerversauerung sowie Veränderungen in der Nährstoff-Verfügbarkeit und im sonstigen Wasserchemismus nur anhand der Artenzahl oder des Artenspektrums abzuschätzen. Vielmehr müssen quantitative Methoden wie die Ermittlung der Abundanzen angewandt werden, um anthropogene und natürliche Störungen des Ökosystems zu erfassen. Es wurde eine Strategie für die behördliche Gewässergüteüberwachung von Bachoberläufen vorgeschlagen, die flächendeckend die Versauerungsgefährdung erfassen kann. Die Auswirkungen der zeitlichen Dynamik des Versauerungschemismus wurden am Beispiel des versauerungsempfindlichen Taxons Baetis spp. (Eintagsfliegen) dargestellt. An S2 und S3 kam es zu starken Versauerungsschüben. Baetis konnte sich nicht ganzjährig halten, sondern nur in versauerungsarmen Phasen im Sommer und im Herbst; es gab einen Besiedlungskreislauf aus Ausrottungs- und Wiederbesiedlungsphasen. Die temporäre Population von Baetis an S2 und S3 bestand nur aus ersten Larvenstadien. Die Probestellen wurden auf horizontalen Gradienten der Umweltfaktoren angeordnet. Bei einigen Parametern gab es keinen Gradienten (z.B. Sauerstoff-Gehalt), bei anderen Parametern waren die Meßstellen auf sehr flachen Gradienten angeordnet (z.B. C:N-Quotient der Feinstkörner), bei den restlichen Meßgrößen waren die Gradienten sehr deutlich (z.B. Alkalinität). Bei den Längsgradienten von Abundanz und Biomasse waren alle Möglichkeiten vertreten: Zunahme (z.B. Leuctra pseudosignifera), Abnahme (z.B. Gammarus pulex), Maximum an der mittleren Probestelle (z.B. Leuctra pseudocingulata) und kein signifikanter Trend (z.B. Nemoura spp.). Abundanz und Biomasse zahlreicher taxonomischer Einheiten hatten ihr Maximum im Längslauf an den quellnächsten Probestellen R1 und S1, z.B. Protonemura spp. und Plectrocnemia spp. Die Lebensgemeinschaften an R1 und S1 waren allerdings völlig unterschiedlich zusammengesetzt. Die häufig vertretene Annahme, versauerte Gewässer seien biologisch tot, ist falsch. Unter Anwendung des 3. biozönotischen Grundprinzips wurde das Maximum von Abundanz und Biomasse in den quellnahen Abschnitten mit dem eustatistischen (stabilen) Regime von Wassertemperatur, Abfluß und Protonen-Gehalt, in der Alten Riefensbeek auch von Alkalinität und ALMER-Relation erklärt. Aufgrund der natürlichen und anthropogenen Störungen war im Längslauf der untersuchten Bäche keine natürliche biozönotische Gliederung des Artenbestands erkennbar. Die Korrelationsberechnungen zwischen den Umweltfaktoren und der Taxazahl ergaben, daß in erster Linie versauerungsrelevante Parameter -- Gehalte saurer Anionen, basischer Kationen und von Metallen, Alkalinität usw. -- die höchsten Korrelationskoeffizienten mit der Taxa-Zahl hatten; unter den natürlichen Meßgrößen zählten nur die Gehalte von DOC und TIC sowie der Anteil der Sande zu der Gruppe mit den höchsten Korrelationskoeffizienten. Die Korrelationsberechnungen zwischen den Umweltfaktoren und den Abundanzen ergab dagegen, daß die quantitative Zusammensetzung der Lebensgemeinschaft nicht nur durch die anthropogene Gewässerversauerung, sondern mindestens genauso durch einige natürliche Meßgrößen beeinflußt wurde. Es gab in den Harzbächen keinen ökologischen Superfaktor, der die quantitative Zusammensetzung der Lebensgemeinschaft überwiegend bestimmte. Auch die Meßgrößen der anthropogenen Gewässerversauerung waren nicht solch ein Superfaktor. Einen ähnlich hohen Einfluß auf die quantitative Zusammensetzung der Lebensgemeinschaft hatten die geologisch bestimmten Umweltfaktoren Leitfähigkeit und TIC-Gehalt, der von der Landnutzung bestimmte DOC-Gehalt sowie der Chlorid-Gehalt, der geologisch, möglicherweise aber auch durch den Eintrag von Straßensalz bestimmt wird. Die Mischung von anthropogenen und natürlichen Faktoren wurde in einem Modell der Wirkung von abiotischen Faktoren auf Bryorheos und Hyporheos dargestellt. Als Beispiel für die zeitliche Nutzung ökologischer Nischen wurde die Verteilung der Larven und Adulten der Dryopidae (Hakenkäfer) im Hyporheos und Bryorheos untersucht. Die Larven wurden vorzugsweise im Hyporheon, die Adulten im Bryorheon angetroffen. Die untersuchten Taxa wurden in die Varianten bryorheobiont, bryorheophil, bryorheotolerant, bryorheoxen und bryorheophob bzw. hyporheobiont, hyporheophil, hyporheotolerant, hyporheoxen und hyporheophob eingeteilt, um ihre räumliche Nutzung ökologischer Nischen zu beschreiben. Die gängige Lehrmeinung, daß das Hyporheon die Kinderstube benthaler Makroinvertebraten ist, konnte für zahlreiche Taxa bestätigt werden (z.B. Habrophlebia lauta). Für die bryorheophilen Taxa (z.B. Gammarus pulex und Baetis spp.) trifft diese Lehrmeinung in den beiden Harzbächen nicht zu. Vielmehr übernimmt das Bryorheon die Funktion einer Kinderstube. Die Larven von Plectrocnemia conspersa / geniculata sowie von Baetis spp. und Amphinemura spp. / Protonemura spp. neben Gammarus pulex zeigten eine Habitatbindung, die erstgenannte Gattung an das Hyporheal, die letztgenannten 3 Taxa an untergetauchte Moospolster (Bryorheal). Die Idee von der Funktion des Hyporheals als Kinderstube der Larven und Jungtiere, als Schutzraum gegen die Verdriftung durch Strömung und vor Fraßdruck durch Räuber sowie als Ort hohen Nahrungsangebots mußte für die letztgenannten 3 Taxa abgelehnt werden. Für sie übernahm das Bryorheal diese Aufgaben. Zwar waren die beiden Bäche oligotroph und die Nahrungsqualität der Feinstkörner im Hyporheal war niedrig. Die Abundanz- und Biomasse-Werte im Bryorheos und Hyporheos gehörten aber zu den weltweit höchsten. Es wurde das Paradoxon diskutiert, daß im Hyporheon der beiden Bäche Diatomeen-Rasen gefunden wurden, obwohl das Hyporheon lichtlos sein soll. Das Hyporheon wurde als ein Ökoton zwischen Benthon / Rheon und Stygon angesehen. Es wurden vier Haupttypen des Hyporheons beschrieben. Wegen des sehr unterschiedlichen Charakters des Hyporheons in verschiedenen Fließgewässern gibt es keinen einheitlichen Satz von abiotischen und biotischen Faktoren, mit denen das Hyporheon vom Benthon und Stygon abgegrenzt werden kann. In den beiden Harzbächen ähnelte das Hyporheon mehr dem Benthon als dem Stygon. Es konnte nicht anhand der chemischen Meßgrößen vom Benthon abgegrenzt werden, sondern anhand der physikalischen Meßgrößen Trübung und der Anteile von Feinsand und Schluffe/Tone sowie anhand der biologischen Parameter Summen-Abundanz und Summen-Biomasse. Aus der Typologie des Hyporheons folgt, daß ein bestimmtes Hyporheon nicht alle in der Literatur beschriebenen Funktionen innerhalb der Fließgewässer-Aue übernehmen kann. Es wurde ein Schema entwickelt, mit dem sich die optimale Liste der Parameter für die Untersuchung eines bestimmten Hyporheons auswählen läßt. Der Tendenz in der Fließgewässer-Ökologie, immer neue Konzepte zu entwickeln, die allgemeingültig sein sollen, wurde das Konzept vom individuellen Charakter von Fließgewässer-Ökosystemen entgegengestellt.
Resumo:
Am Fachgebiet Massivbau (Institut für Konstruktiven Ingenieurbau – IKI) des Fachbereichs Bauingenieurwesen der Universität Kassel wurden Bauteilversuche an zweiaxial auf Druck-Zug belasteten, faserfreien und faserverstärkten Stahlbetonscheiben durchgeführt. Dabei wurden die Auswirkungen der Querzugbeanspruchung und der Rissbildung auf die Druckfestigkeit, auf die Stauchung bei Erreichen der Höchstlast sowie auf die Drucksteifigkeit des stabstahl- und faserbewehrten Betons an insgesamt 56 faserfreien und faserverstärkten Beton- und Stahlbetonscheiben untersucht. Auf der Grundlage der experimentell erhaltenen Ergebnisse wird ein Vorschlag zur Abminderung der Druckfestigkeit des gerissenen faserfreien und faserbewehrten Stahlbetons in Abhängigkeit der aufgebrachten Zugdehnung formuliert. Die Ergebnisse werden den in DIN 1045-1 [D4], Eurocode 2 [E3, E4], CEB-FIP Model Code 1990 [C1] und ACI Standard 318-05 [A1] angegebenen Bemessungsregeln für die Druckstrebenfestigkeit des gerissenen Stahlbetons gegenübergestellt und mit den Untersuchungen anderer Wissenschaftler verglichen. Die bekannten Widersprüche zwischen den Versuchsergebnissen, den vorgeschlagenen Modellen und den Regelwerken aus U.S.A., Kanada und Europa können dabei weitgehend aufgeklärt werden. Für nichtlineare Verfahren der Schnittgrößenermittlung und für Verformungsberechnungen wird ein Materialmodell des gerissenen faserfreien und faserbewehrten Stahlbetons abgeleitet. Hierzu wird die für einaxiale Beanspruchungszustände gültige Spannungs-Dehnungs-Linie nach Bild 22 der DIN 1045-1 auf den Fall der zweiaxialen Druck-Zug-Beanspruchung erweitert.
Resumo:
The ongoing growth of the World Wide Web, catalyzed by the increasing possibility of ubiquitous access via a variety of devices, continues to strengthen its role as our prevalent information and commmunication medium. However, although tools like search engines facilitate retrieval, the task of finally making sense of Web content is still often left to human interpretation. The vision of supporting both humans and machines in such knowledge-based activities led to the development of different systems which allow to structure Web resources by metadata annotations. Interestingly, two major approaches which gained a considerable amount of attention are addressing the problem from nearly opposite directions: On the one hand, the idea of the Semantic Web suggests to formalize the knowledge within a particular domain by means of the "top-down" approach of defining ontologies. On the other hand, Social Annotation Systems as part of the so-called Web 2.0 movement implement a "bottom-up" style of categorization using arbitrary keywords. Experience as well as research in the characteristics of both systems has shown that their strengths and weaknesses seem to be inverse: While Social Annotation suffers from problems like, e. g., ambiguity or lack or precision, ontologies were especially designed to eliminate those. On the contrary, the latter suffer from a knowledge acquisition bottleneck, which is successfully overcome by the large user populations of Social Annotation Systems. Instead of being regarded as competing paradigms, the obvious potential synergies from a combination of both motivated approaches to "bridge the gap" between them. These were fostered by the evidence of emergent semantics, i. e., the self-organized evolution of implicit conceptual structures, within Social Annotation data. While several techniques to exploit the emergent patterns were proposed, a systematic analysis - especially regarding paradigms from the field of ontology learning - is still largely missing. This also includes a deeper understanding of the circumstances which affect the evolution processes. This work aims to address this gap by providing an in-depth study of methods and influencing factors to capture emergent semantics from Social Annotation Systems. We focus hereby on the acquisition of lexical semantics from the underlying networks of keywords, users and resources. Structured along different ontology learning tasks, we use a methodology of semantic grounding to characterize and evaluate the semantic relations captured by different methods. In all cases, our studies are based on datasets from several Social Annotation Systems. Specifically, we first analyze semantic relatedness among keywords, and identify measures which detect different notions of relatedness. These constitute the input of concept learning algorithms, which focus then on the discovery of synonymous and ambiguous keywords. Hereby, we assess the usefulness of various clustering techniques. As a prerequisite to induce hierarchical relationships, our next step is to study measures which quantify the level of generality of a particular keyword. We find that comparatively simple measures can approximate the generality information encoded in reference taxonomies. These insights are used to inform the final task, namely the creation of concept hierarchies. For this purpose, generality-based algorithms exhibit advantages compared to clustering approaches. In order to complement the identification of suitable methods to capture semantic structures, we analyze as a next step several factors which influence their emergence. Empirical evidence is provided that the amount of available data plays a crucial role for determining keyword meanings. From a different perspective, we examine pragmatic aspects by considering different annotation patterns among users. Based on a broad distinction between "categorizers" and "describers", we find that the latter produce more accurate results. This suggests a causal link between pragmatic and semantic aspects of keyword annotation. As a special kind of usage pattern, we then have a look at system abuse and spam. While observing a mixed picture, we suggest that an individual decision should be taken instead of disregarding spammers as a matter of principle. Finally, we discuss a set of applications which operationalize the results of our studies for enhancing both Social Annotation and semantic systems. These comprise on the one hand tools which foster the emergence of semantics, and on the one hand applications which exploit the socially induced relations to improve, e. g., searching, browsing, or user profiling facilities. In summary, the contributions of this work highlight viable methods and crucial aspects for designing enhanced knowledge-based services of a Social Semantic Web.
Resumo:
I have designed and implemented a system for the multilevel verification of synchronous MOS VLSI circuits. The system, called Silica Pithecus, accepts the schematic of an MOS circuit and a specification of the circuit's intended digital behavior. Silica Pithecus determines if the circuit meets its specification. If the circuit fails to meet its specification Silica Pithecus returns to the designer the reason for the failure. Unlike earlier verifiers which modelled primitives (e.g., transistors) as unidirectional digital devices, Silica Pithecus models primitives more realistically. Transistors are modelled as bidirectional devices of varying resistances, and nodes are modelled as capacitors. Silica Pithecus operates hierarchically, interactively, and incrementally. Major contributions of this research include a formal understanding of the relationship between different behavioral descriptions (e.g., signal, boolean, and arithmetic descriptions) of the same device, and a formalization of the relationship between the structure, behavior, and context of device. Given these formal structures my methods find sufficient conditions on the inputs of circuits which guarantee the correct operation of the circuit in the desired descriptive domain. These methods are algorithmic and complete. They also handle complex phenomena such as races and charge sharing. Informal notions such as races and hazards are shown to be derivable from the correctness conditions used by my methods.