Photocatalysis on Fine Powders of Perovskite Oxides

Fine powders of semiconductor oxides have been widely used as photocatalysts for many reactions. Among the various photocatalytic reactions, water splitting has been given much importance, since it is a promising chemical route for solar energy conversion. Perovskite oxides, in particular SrTiO, have been commonly used as photocatalysts because some of them can decompose H,O into H, and 0, without an external bias potential (1). In turn, this is because the conduction band (CB) edges of some of the perovskite oxides are more negative than the H+/H, energy level. Since the catalytic activity is related to the surface properties of the solids, fine powders rather than single crystals are used. Photocatalysis on fine powers can be conveniently discussed in three parts, viz. preparation, characterization and their catalytic activity. Presently, photo-decomposition of water using SrTiO, fine powders is discussed in greater detail, although other photocatalytic reactions on various perovskite oxides are also briefly dealt with.

Interaction analysis of strip footing resting on a non-homogeneous elastic medium

In this paper, a plane stress solution for the interaction analysis of strip footing resting on (i) a non-homogeneous elastic half-plane and (ii) a non-homogeneous elastic layer resting on a rigid stratum has been presented. The analysis has been done using a combined analytical and FEM method in which the discretization of the half-plane is not required and thereby minimizes the computational efforts considerably. The contact pressure distribution and the settlement profile for the selected cases of varying modulus half-plane, which has more relevance to foundation engineering, have been given. Experimental verification through a photoelastic method of stress analysis has been carried out for the case of footing on Gibson elastic half-plane, and the contact pressure distribution thus obtained has been compared with the theoretical results. Copyright (C) 1996 Elsevier Science Ltd

Microwave-assisted selective deoxygenation of layer- and chain-containing oxides

Very rapid (within 5 min), selective, single-step deoxygenation of layer- and chain-containing oxides, MoO3, CrO3, V2O5, alpha-VOPO4 . 2H(2)O and Ag6Mo10O33 has been accomplished using graphitic carbon in a microwave-assisted reaction. The products were found to be MoO2, Cr2O3, VO2, VPO4 and a mixture of (Ag + MoO2), respectively. Products were characterised by X-ray diffraction (XRD), differential scanning calorimetry (DSC), IR and electron paramagnetic resonance (EPR) spectroscopies. Although conventional methods of preparing these materials are tedious, the present method is simple, fast and yields very homogeneous products of good crystallinity. Our results reveal that while layer- and chain-containing oxides undergo rapid microwave-assisted carbothermal reduction, the non-layered materials do not. The high structural selectivity of these reactions is suggestive of the topochemical nature of the fast reduction process.

New uniform solid catalyst for the low-temperature oxidation of carbon monoxide: A triple-layered rare earth perovskite containing Co and Cu ions

Oxygen reactivity and catalytic activity of the cobalt-containing layered defect perovskites, YBa2Cu2CoO7+delta and LaBa2Cu2CoO7+delta, in comparison with LaBa2Cu3O7-delta have been investigated employing temperature-programmed desorption (TPD) and temperature-programmed surface reactions (TPSR) in the stoichiometric and catalytic mode using carbon monoxide as a probe molecule. TPD studies showed evidence for the presence of two distinct labile oxygen species, one at (0 0 1/2) sites and the other at (0 1/2 0) sites in LaBa2Cu2CoO7+delta against a single labile species at (0 1/2 0) in the case of two other oxides. The activation energies for the catalytic oxidation of carbon monoxide by oxygen over LaBa2Cu3O7-delta, YBa2Cu2CoO7+delta, and LaBa2Cu2CoO7+delta have been estimated to be 24.2, 15.9, and 13.6 kcal/mol, respectively. The reactivity and catalytic activity of the oxide systems have been interpreted in terms of the structural changes brought about by substituents, guided by a directing effect of the larger rare earth cation. TPSR profiles, structural analysis, and infrared spectroscopic investigations suggest that the oxygen present at (0 0 1/2) sites in the case of LaBa2Cu2CoO7+delta is accessible to catalytic oxidation of CO through a Mars-Van Krevelen pathway. Catalytic conversion of CO to CO2 over LaBa2Cu2CoO7+delta occurs at 200 degrees C. The enhanced reactivity is explained in terms of changes brought about in the coordination polyhedra around transition metals, enhanced basal plane oxygen diffusivity, and redox potentials of the different transition metal cations.

Role of free valences and spin densities on the migrating atom in location of saddle points in radical-exchange reactions

The principle of the conservation of bond orders during radical-exchange reactions is examined using Mayer's definition of bond orders. This simple intuitive approximation is not valid in a quantitative sense. Ab initio results reveal that free valences (or spin densities) develop on the migrating atom during reactions. For several examples of hydrogen-transfer reactions, the sum of the reaction coordinate bond orders in the transition state was found to be 0.92 +/- 0.04 instead of the theoretical 1.00 because free valences (or spin densities) develop on the migrating atom during reactions. It is shown that free valence is almost equal to the square of the spin density on the migrating hydrogen atom and the maxima in the free valence (or spin density) profiles coincide (or nearly coincide) with the saddle points in the corresponding energy profiles.

Synthesis and catalytic properties of cobalt- and molybdenum-containing mesoporous MCM-41 molecular sieves

Mesoporous MCM-41 type silicas containing molybdenum and cobalt have been prepared with pore sizes in the range 30-38 Angstrom and 54-59 Angstrom. Catalytic properties of these materials have been examined with respect to the oxidation of cyclooctene and aniline.

Enhanced sensitivity for the differential pulse polarographic determination of molybdenum(VI) based on adsorption catalytic current

A differential pulse polarographic (DPP) method based on the adsorption catalytic current in a medium containing chlorate and 8-hydroxyquinoline (oxine) is suggested for the determination of molybdenum(VI). Experimental conditions such as pH and the composition of supporting electrolyte have been optimized to get a linear calibration graph at trace levels of Mo(VI). The sensitivity for molybdenum can be considerably enhanced by this method. The influence of possible interferences on the catalytic current has been investigated. The sensitivity of the method is compared with those obtained for other DPP methods for molybdenum. A detection limit of 1.0 x 10(-8) mol/L has been found.

Further studies on Norrish type II reactions including a reaction in the first excited singlet state and cyclization of 1:4 biradicals

The Norrish type II processes of methyl-2,2-dimethyl- cyclopropyl ketone, alpha-alkoxy acetones and alkyl pyruvates have been examined using the AM1 semi-empirical molecular orbital method with complete geometry optimization at the partial configuration interaction level in the restricted Hartree-Fock (RHF) frame. The results reveal that the methyl-substituted cyclopropyl ketone has a constrained geometry favourable for hydrogen abstraction from the gamma-position relative to the carbonyl group in the excited singlet state. The presence of the ether oxygen atom in the beta-position relative to the carbonyl group in alkoxy acetones and alkyl pyruvates leads to increased reactivity relative to alkyl monoketones and diketones respectively. The cyclization of 1:4 biradicals has been studied in the unrestricted Hartree-Fock (UHF) frame, and the results reveal that the 1:4 biradical derived from alkoxy acetones readily cyclizes to form oxetanols. On the other hand, in the 1:4 biradicals derived from methyl-substituted cyclopropyl ketone, the three-membered ring breaks readily to form an enol intermediate. Delocalization of an odd electron in 1:4 biradicals derived from alkyl pyruvates is thought to make cyclization difficult.

Organometallic Chemistry of Diphosphazanes. 11. Reactions of fac-[Mo(CO)3(MeCN){.eta.2-Ph2PN(Pri)PPh(DMP)}] (DMP = 3,5-Dimethyl-1-Pyrazolyl) with Diphosphazanes and Diphosphinoalkanes and Oxidative Addition with Iodine

The use of fac-[Mo(CO)(3)(MeCN)(eta(2)-L(1))] (1a) {L(1) = Ph(2)PN(Pr-i)PPh(DMP)}(2) as a precursor to metalloligands and bimetallic, heterotrimetallic, and heptacoordinated complexes is reported. The reaction of 1a with diphosphazane, dppa, or a diphosphinoalkane such as dppm or dppe yields the fac-eta(1)-diphosphine substituted metalloligands, fac-[Mo(CO)(3)(eta(2)-L(1))(eta(1)-PXP)] {PXP = dppa (2), dppm (3), and dppe (4)}. These undergo isomerization to yield the corresponding mer-diphosphine complexes (5-7). Oxidation of the uncoordinated phosphorus atom of the mer-eta(1)-dppm-substituted complex eventually provides mer-[Mo(CO)(3)-(eta(2)-L(1)){eta(1)-Ph(2)PCH(2)P(O)Ph(2)}](8). The structure of the latter complex has been confirmed by single crystal X-ray diffraction {triclinic system, P ($) over bar 1; a = 11.994(3), b = 14.807(2), c = 15.855(3) Angstrom; alpha = 114.24(1), beta = 91.35(2), and gamma = 98.95(1)degrees; Z = 2, 4014 data (F-0 > 5 sigma(F-0)), R = 0.066, R(W) = 0.069}. Treatment of the dppe metalloligand 7 with [PtCl2(COD)] yields the heterotrimetallic complex cis-[PtCl2{mer-[Mo(CO)(3)(eta(2)-L(1))(eta(1)-dppe]}(2)] (9). Attempts to prepare a related trimetallic complex with the dppm-containing metalloligand were unsuccessful; only the tetracarbonyl complex cis-[Mo(CO)(4)(eta(2)-L(1))] (1b) and cis-[PtCl2(eta(2)-dppm)] were obtained. Reaction of la with dppe in the ratio 2:1 yields the mer-mer dinuclear complex [{mer-[Mo(CO)(3)(eta(2)-L(1))]}(2)(mu-dppe)] (10) bridged by dppe. Oxidation of 1a with iodine yields the Mo(II) heptacoordinated complex [MoI2(CO)(2)(eta(3)-L(1))] (11) with tridentate PPN coordination. The same Mo(II) complex 11 is also obtained by the direct oxidation of the tetracarbonyl complex cis-[Mo(CO)(4)(eta(2)-L(1))] (1b) with iodine. The structure of 11 has been confirmed by X-ray diffraction studies {monoclinic system, Cc; a = 10.471(2), b = 19.305(3), c = 17.325(3) Angstrom; beta = 95.47(2)degrees; Z = 4, 3153 data (F-0 > 5 sigma(F-0)), R = 0.049, R(W) = 0.051}. This complex exhibits an unusual capped-trigonal prismatic geometry around the metal. A similar heptacoordinated complex 12 with a chiral diphosphazane ligand {L(3) = (S,R)-P(h)2PN-(*CHMePh)*PPh(DMP)} has also been synthesized.

Reactions of cyanogen radical with alkanes and an explanation for negative temperature dependence of rate constants

Reactions of cyanide radicals with alkanes have been investigated by ab initio methods. It is found that the potential energy surface for reaction of CN with a primary C-H bond in methane has a small positive barrier while reactions of CN with a secondary and a tertiary C-H bond in alkanes are barrierless at the correlated level. A simple explanation for the obtained negative temperature dependence of rate constants for reactions of CN with a secondary and a tertiary C-H bond in alkanes are given in terms of the collision theory of bimolecular reactions. It is shown that for barrierless reactions the negative temperature dependence of the rate constants is attributed to the variation of the pre-exponential factor with temperature.

Study of the reactions of pyridinium poly(hydrogen fluoride) with some ternary oxides

The products of the reaction of pyridinium poly(hydrogen fluoride), PPHF, with KIO3, Na2SnO3, NaBiO3, K2CrO4, Na2MoO4 and Na2WO4 were KIO2F2; Na2SnF6; NaHF2, BiF3; K3CrF6, KHF2, (PyH)(3)CrF6; NaHF2, (PyH)(2)MoO2F4.2NaHF(2); and (PyH)(2)WO2F4.2NaHF(2), respectively, while KClO3, KBrO3 and KlO(4) react with complete decomposition to form KHF2 as the fluorinated product. This differential reactivity and mode of reaction has been discussed in terms of the oxidation state of the central atom, the nature and strength of the bonds and the complex behaviour of the formed intermediate or fluorinated products that undergo complexation or solvation with pyridine and/or hydrogen fluoride.

Synthesis and esterolytic chemistry of some (dialkylamino) pyridine-functionalized micellar aggregates. Evidence of catalytic turnover

Four new (dialkylamino)pyridine-functionalized surfactants have been synthesized. Micelles were generated either from the surfactant alone in aqueous buffer (pH 8.5 or 9.0) or by comicellization in 1 x 10(-3)-1 x 10(-4) M aqueous micellar cetyltrimethylammonium bromide (CTABr) solution at pH 8.5 or 9.0. Such aggregates were used to cleave p-nitrophenyl alkanoates or p-nitrophenyl diphenylphosphate. The nucleophilic reagents and the second-order ''catalytic'' rate constants toward esterolysis of the substrate p-nitrophenyl octanoate (at 25 degrees C, pH 9.0) were [cat.] = 1 x 10(-4) M, [CTABr] = 1 x 10(-3) M, and k(cat.) = 440.13 M(-1) s(-1) for 1b, [cat.] = 5 x 10(-4) M, [CTABr] = 5 x 10(-4) M, and k(cat.) = 30.8 M(-1) s(-1) for 1c, [cat.] = 5 x 10(-4) M, [CTABr] = 5 x 10(-3) M, and k(cat.) = 183.64 M(-1) s(-1) for 2a, and [cat.] = 3 x 10(-4) M and k(cat.) = 54.1 M(-1) s(-1) for 2b. The catalytic systems, especially 1b/CTABr and 2a/CTABr, also conferred significantly greater reactivity toward the esters derived from alkanoic acids of moderate chain length (C-6-C-10) during hydrolytic cleavages relative to their shorter and longer counterparts. Importantly, the catalytic systems comprising the coaggregates of either neutral 1b and CTABr (1:10) or anionic 2a and CTABr (1:10) conformed to the Michaelis-Menten kinetic scheme and demonstrated turnover behavior in the presence of excess substrate.

Mutations in the Res subunit of the EcoPI restriction enzyme that affect ATP-dependent reactions

The Res subunits of the type III restriction-modification enzymes share a statistically significant amino acid sequence similarity with several RNA and DNA helicases of the so-called DEAD family. It was postulated that in type III restriction enzymes a DNA helicase activity may be required for local unwinding at the cleavage site. The members of this family share seven conserved motifs, all of which are found in the Res subunit of the type III restriction enzymes. To determine the contribution, if any, of these motifs in DNA cleavage by EcoPI, a type III restriction enzyme, we have made changes in motifs I and II. While mutations in motif I (GTGKT) clearly affected ATP hydrolysis and resulted in loss of DNA cleavage activity, mutation in motif II (DEPH) significantly decreased ATP hydrolysis but had no effect on DNA cleavage. The double mutant R.EcoPIK90R-H229K showed no significant ATPase or DNA restriction activity though ATP binding was not affected. These results imply that there are at least two ATPase reaction centres in EcoPI restriction enzyme. Motif I appears to be involved in coupling DNA restriction to ATP hydrolysis. Our results indicate that EcoPI restriction enzyme does not have a strand separation activity. We suggest that these motifs play a role in the ATP-dependent translocation that has been proposed to occur in the type III restriction enzymes. (C) 1997 Academic Press Limited.

Oxidation of aqueous sulphur dioxide catalysed by poly-4-vinylpyridine-Cu(II) complex .2. Combined homogeneous and heterogeneous phase oxidation

Aqueous phase oxidation of sulphur dioxide at low concentrations catalysed by a PVP-Cu complex in the solid phase and dissolved Cu(II) in the liquid phase is studied in a rotating catalyst basket reactor (RCBR). The equilibrium adsorption of Cu(II) and S(VI) on PVP particles is found to be of the Langmuir-type. The diffusional effects of S(IV) species in PVP-Cu resin are found to be insignificant whereas that of product S(VI) are found to be significant. The intraparticle diffusivity of S(VI) is obtained from independent tracer experiments. In the oxidation reaction HSO3- is the reactive species. Both the S(IV) species in the solution, namely SO2(aq) and HSO3- get adsorbed onto the active PVP-Cu sites of the catalyst, but only HSO3- undergoes oxidation. A kinetic mechanism is proposed based on this feature which shows that SO2(aq) has a deactivating effect on the catalyst. A rate model is developed for the three-phase reaction system incorporating these factors along with the effect of concentration of H2SO4 on the solubility of SO2 in the dilute aqueous solutions of Cu(II). Transient oxidation experiments are conducted at different conditions of concentration of SO2 and O-2 in the gas phase and catalyst concentration, and the rate parameters are estimated from the data. The observed and calculated profiles are in very good agreement. This confirms the deactivating effect of nonreactive SO2(aq) on the heterogeneous catalysis.

Some recent advances in the theory of homogeneous isotropic turbulence

We review some advances in the theory of homogeneous, isotropic turbulence. Our emphasis is on the new insights that have been gained from recent numerical studies of the three-dimensional Navier Stokes equation and simpler shell models for turbulence. In particular, we examine the status of multiscaling corrections to Kolmogorov scaling, extended self similarity, generalized extended self similarity, and non-Gaussian probability distributions for velocity differences and related quantities. We recount our recent proposal of a wave-vector-space version of generalized extended self similarity and show how it allows us to explore an intriguing and apparently universal crossover from inertial- to dissipation-range asymptotics.