Fibras de sisal (Agave sisalana) como isolante térmico de tubulações

In the last decades there was a significant increasing of the numbers of researchers that joint efforts to find alternatives to improve the development of low environmental impact technology. Materials based on renewable resources have enormous potentials of applications and are seen as alternatives for the sustainable development. Within other parameters, the sustainability depends on the energetic efficiency, which depends on the thermal insulation. Alternative materials, including vegetal fibers, can be applied to thermal insulation, where its first goal is to minimize the loss of energy. In the present research, it was experimentally analyzed the thermal behavior of fiber blankets of sisal (Agave sisalana) with and without surface treatment with oxide hidroxide (NaOH). Blankets with two densities (1100/1200 and 1300/1400 g/m2) were submitted to three rates of heat transfer (22.5 W, 40 W and 62.5 W). The analysis of the results allowed comparing the blankets treated and untreated in each situation. Others experiments were carried out to obtain the thermal conductivity (k), heat capacity (C) and the thermal diffusivity (α) of the blankets. Thermo gravimetric analyses were made to the verification of the thermal stability. Based on the results it was possible to relate qualitatively the effect of the heat transfer through the sisal blankets subjected to three heat transfer rates, corresponding to three temperature values (77 °C, 112 °C e 155 °C). To the first and second values of temperature it was verified a considerable reduction on the rate of heat transfer; nevertheless, to the third value of temperature, the surface of the blankets (treated and untreated) in contact with the heated surface of the tube were carbonized. It was also verified, through the analyses of the results of the measurements of k, C e α, that the blankets treated and untreated have values near to the conventional isolating materials, as glass wool and rock wool. It could be concluded that is technically possible the use of sisal blankets as constitutive material of thermal isolation systems in applications where the temperature do not reach values greater than 112 ºC

Pré-condicionamento das sementes de mamoneira para o teste de tetrazólio

Preconditioning of castor bean seeds for the tetrazolium test. This research had the objective of standardizing the methodology for preconditioning of castor bean (Ricinus communis L.) seeds for the evaluation of their physiological potential by the tetrazolium test. The evaluated seed preconditioning methods were: seeds with coat between moist paper towel at 30, 35 and 40 degrees C for 6, 8, 10, 12, 14, 16 and 18 hours; and seeds without coat between moist paper towel; and seeds with coat immersed in water, at 25, 30, 35 and 40 degrees C for 1, 2, 3, 4, 5 and 6 hours. After preconditioning, the seed coat was removed, the seeds were cut lengthwise, and immersed in tetrazolium solution at a concentration of 0.2% for 120 minutes at 35 degrees C. The seeds' germination percentage, moisture content before and after preconditioning, and staining uniformity after the tetrazolium were evaluated. The statistical design was completely randomized, and the means comparisons were accomplished by the Tukey test at 0.05 level of probability. It was concluded that castor bean seeds should be preconditioned with coat between moist paper towel at 35 degrees C for 12 hours, so that the results of the tetrazolium test will be similar to those obtained in the germination test.

Envelhecimento ambiental acelerado em PRF a base de tecidos híbridos kevlar/vidro: propriedades e instabilidade estrutural

There are a number of damaging mechanisms that various materials can suffer in service. However, when working with polymer composite materials, this is something that requires analysis, especially when exposed to adverse environmental conditions. Thus, the objective of the present thesis is the study of the direct influence of environmental aging and the form of hybridization of the reinforcement woven on the structural stability, surfacedegradation and fracture process of polymer composites laminates. For this, the development of two polymer composite laminates was necessary, where one of them was reinforced with a bi-directional woven with hybrid strandsofkevlar-49/glass-Efibers, and the other also with a bi-directionalwoven, however with weft and warpformed of alternating strandsof Kevlar-49 fibers and glass-E fiber The reinforcementwoven are industrially manufactured. Both laminates use a polyester resin as a matrixand are made up of four layers each. All laminates were industrially prepared by the hand lay-up method of manufacturing. To do this, test specimens were manufactured of the respective laminates and submitted to environmental aging accelerated through the aging chamber. They were exposed to alternating cycles of UV radiation and moisture (heated steam) for a standard defined period. At the end of the exposure period the specimens were subjected to mechanical tests of uniaxial tensile and bending in three points and to the characterizationsof the fracture and surface deterioration. In addition, they were submitted to a structural degradation assessment by the measurement of mass variation technique (MMVT) and the measurement of thickness variation technique (MTVT), this last technique being developed in this thesis. At the end of the analysis it was observed that the form of hybridization of the reinforcement woven and the aging process directly influence with losses or gain in mechanical properties, with losses in the structural degradation and in the formation and propagation of damage mechanism of the developedcomposite laminates

Efeitos da radiação uv, temperatura e vapor aquecido nos compósitos poliméricos: monitoramento, instabilidade estrutural e fratura

The application of composite materials and in particular the fiber-reinforced plastics (FRP) has gradually conquered space from the so called conventional materials. However, challenges have arisen when their application occurs in equipment and mechanical structures which will be exposed to harsh environmental conditions, especially when there is the influence of environmental degradation due to temperature, UV radiation and moisture in the mechanical performance of these structures, causing irreversible structural damage such as loss of dimensional stability, interfacial degradation, loss of mass, loss of structural properties and changes in the damage mechanism. In this context, the objective of this thesis is the development of a process for monitoring and modeling structural degradation, and the study of the physical and mechanical properties in FRP when in the presence of adverse environmental conditions (ageing). The mechanism of ageing is characterized by controlled environmental conditions of heated steam and ultraviolet radiation. For the research, it was necessary to develop three polymer composites. The first was a lamina of polyester resin reinforced with a short glass-E fiber mat (representing the layer exposed to ageing), and the other two were laminates, both of seven layers of reinforcement, one being made up only of short fibers of glass-E, and the other a hybrid type reinforced with fibers of glass-E/ fibers of curaua. It should be noted that the two laminates have the lamina of short glass-E fibers as a layer of the ageing process incidence. The specimens were removed from the composites mentioned and submitted to environmental ageing accelerated by an ageing chamber. To study the monitoring and modeling of degradation, the ageing cycles to which the lamina was exposed were: alternating cycles of UV radiation and heated steam, a cycle only of UV radiation and a cycle only of heated steam, for a period defined by norm. The laminates have already undergone only the alternating cycle of UV and heated steam. At the end of the exposure period the specimens were subjected to a structural stability assessment by means of the developed measurement of thickness variation technique (MTVT) and the measurement of mass variation technique (MMVT). Then they were subjected to the mechanical tests of uniaxial tension for the lamina and all the laminates, besides the bending test on three points for the laminates. This study was followed by characterization of the fracture and the surface degradation. Finally, a model was developed for the composites called Ageing Zone Diagram (AZD) for monitoring and predicting the tensile strength after the ageing processes. From the results it was observed that the process of degradation occurs Abstract Raimundo Nonato Barbosa Felipe xiv differently for each composite studied, although all were affected in certain way and that the most aggressive ageing process was that of UV radiation, and that the hybrid laminated fibers of glass-E/curaua composite was most affected in its mechanical properties

Análise da eficiência de aquecedor solar espiral com e sem efeito estufa para piscinas

The technical and economic viability of solar heating for swimming pools is unquestionable, besides there it replaces the high costs and environmental impacts of conventional supply of energy, and it improves an optimization in the pool heating uses. This work applies the principles of the greenhouse effect: advanced thermodynamics, heat retention and equalization of temperature, to optimize the solar heating equipment, reducing the area required by collectors as much as 40% (still estimated value) for commercial collectors, with minor architectural and aesthetic impacts on the environment. It features a solar heating alternative in pools, whose main characteristics: low cost, simplicity in manufacturing and assembly and a faster heating. The system consists of two collectors spiral hoses made of polyethylene with a hundred meters each, and working on a forced flow, with only one pass of the working fluid inside the coils, and is used to pump itself treatment of pool water to obtain the desired flow. One of the collectors will be exposed to direct solar radiation, and the other will be covered by a glass slide and closed laterally, so providing the greenhouse effect. The equipment will be installed in parallel and simultaneously exposed to the sun in order to obtain comparative data on their effectiveness. Will be presented results of thermal tests for this the two cases, with and without transparent cover. Will be demonstrated, by comparison, the thermal, economic and material feasibility of these systems for heating swimming pools.

Desenvolvimento de têxteis técnicos para reforço de compósitos poliméricos

Materials denominated technical textiles can be defined as structures designed and developed with function to fulfill specific functional requirements of various industrial sectors as are the cases of the automotive and aerospace industries. In this aspect the technical textiles are distinguished from conventional textile materials, in which the aesthetic and of comfort needs are of primordial importance. Based on these considerations, the subject of this dissertation was established having as its main focus the study of development of textile structures from aramid and glass fibers and acting in order to develop the manufacture of composite materials that combine properties of two different structures, manufactured in an identical operation, where each structure contributes to improving the properties of the resulting composite material. Therefore were created in laboratory scale, textile structures with low weight and different composition: aramid (100%), glass (100%) and aramid /glass (65/35%), in order to use them as a reinforcing element in composite materials with polyester matrix. These composites were tested in tension and its fracture surface, evaluated by MEV. Based on the analysis of mechanical properties of the developed composites, the efficiency of the structures prepared as reinforcing element were testified by reason of that the resistance values of the composites are far superior to the polyester matrix. It was also observed that hybridization in tissue structure was efficient, since the best results obtained were for hybrid composites, where strength to the rupture was similar to the steel 1020, reaching values on the order of 340 MPa

Influência da umidade nas propriedades mecânicas dos compósitos poliméricos híbridos (sisal/ vidro)

This study aims to evaluate the mechanical properties of polymer matrix composites reinforced with sisal fabric bidirectional tissue (Agave sisalana,) and E-glass fibers, containing the following configuration: a polymer matrix hybrid composite (Polyester Resin orthophalic) reinforced with three (3) layers of glass fibers and alternating-2 (two) layers of bidirectional sisal fabric, and finally a composite of polymer matrix reinforced with five (5) layers of glass fiber mat-type E. For this purpose as first step, the preparation of by sisal, since they are not on the market. The composites were made by manual lamination (Hand lay-up) and evaluated for tensile properties and three point bending both in the dry, and wet conditions aswele as immersed in oil. Macroscopic and microscopic characteristics of the materialsweve awalysed, after the completion of the mechanical tests. After the studies, it was proven that the sisal fiber decreases the tensile stiffness of the material above 50% for both situations studied the tensile strength of the material decreases by approximately 40% for the cases mentioned, and when compared to the specific strength stiffness values drop to 14.6% and 29.02% respectively for the dry state only. Constants for bending the values were are to approximately 50% to 25% for strength and stiffness of the material for the cases dry, wet and immersed in oil. Under the influence of tension fluids do not interfere in the stiffness of the material for the bending tests, the same does not occur with the resistance, and these values are modified only in the cases stiffness and flexural strength

Tubulações de PRFV com adição de areia quartzosa visando sua aplicação na indústria do petróleo

Fillers are often added in composites to enhance performance and/or to reduce cost. Fiberglass pipes must meet performance requirements and industrial sand is frequently added for the pipe to be cost competitive. The sand is added to increase pipe wall thickness, thus increase pipe stiffness. The main goal of the present work is to conduct an experimental investigation between pipes fabricated with and without de addition of sand, to be used in the petroleum industry. Pipes were built using E-glass fibers, polyester resin and siliceous sand. The fabrication process used hand lay up and filament winding and was divided in two different parts: the liner and the structural wall. All tested pipes had the same liner, but different structural wall composition, which is the layer where siliceous sand may be added or not. The comparative investigation was developed considering the results of longitudinal tensile tests, hoop tensile tests, hydrostatic pressure leak tests and parallel-plate loading stiffness tests. SEM was used to analyze if the sand caused any damage to the glass fibers, during the fabrication process, because of the fiber-sand contact. The procedure was also used to verify the composite conditions after the hydrostatic pressure leak test. The results proved that the addition of siliceous sand reduced the leak pressure in about 17 %. In the other hand, this loss in pressure was compensated by a stiffness increment of more than 380 %. MEV analyses show that it is possible to find damage on the fiber-sand contact, but on a very small amount. On most cases, the contact occurs without damage evidences. In summary, the addition of sand filler represented a 27.8 % of cost reduction, when compared to a pipe designed with glass fiber and resin only. This cost reduction combined to the good mechanical tests results make siliceous sand filler suitable for fiberglass pressure pipes

Concentração da solução de tetrazólio e período de coloração do teste para sementes de mamoneira

O objetivo do trabalho foi estudar a concentração da solução de tetrazólio e o período de coloração do teste para a avaliação do potencial fisiológico de sementes de mamoneira (Ricinus communis L.), padronizando a nomenclatura das cores observadas nas sementes após a coloração. Os tratamentos de concentração da solução de tetrazólio e períodos de coloração estudados foram: 0,075% e 0,1% por 120, 180 e 240 minutos, 0,2% por 60, 120 e 180 minutos, 0,5% por 60, 90 e 120 minutos e 1,0% por 30, 60 e 90 minutos. Os resultados foram comparados com os obtidos nos testes de germinação. A coloração das sementes após o teste de tetrazólio, em cada tratamento, foi avaliada mediante comparação com as fichas de cor do catálogo de Munsell, determinando-se a porcentagem de sementes observada em cada cor. O delineamento experimental foi o inteiramente casualizado e a comparação de médias realizada pelo teste de Tukey a 5% de probabilidade. Para avaliar o potencial fisiológico pelo teste de tetrazólio, as sementes de mamoneira devem ser imersas na solução de tetrazólio na concentração de 0,2% por 120 minutos, a 35ºC. Nesse tratamento, as sementes viáveis após a coloração na solução de tetrazólio apresentaram predominantemente as cores rosa e rosa-escuro em suas estruturas essenciais, portanto essas podem ser consideradas como as cores características para o teste de tetrazólio em sementes de mamoneira.

Alternância no uso dos modos indicativo e subjuntivo em orações subordinadas substantivas: uma comparação entre o português do Brasil e o francês do Canadá

The purpose of this work is to analyze the use of the indicative mood, instead of the subjunctive prescribed by the normative grammar, in complement clauses introduced by the conjunction que in Brazilian Portuguese. Contexts of use of the subjunctive according to grammatical prescription, and contexts of fluctuation on the use of that verbal mood were analyzed, in an attempt to investigate what interferes on the choice of the mood by the user of the language. This study is based on North-American Functional Linguistics theoretical perspective, oriented to analyzing language in use, in the light of the principles of grammaticalization and markedness. The results obtained support that the contexts that favor the indicative over the subjunctive are those composed by a complement clause functioning as a direct object the unmarked clause of all complement clauses and by a verb on the main sentence that belongs to the semantic field of low certainty, corresponding to the epistemic sub-mode the unmarked category of the deontic sub-mode. The results indicate that pragmatics and semantics factors influence the language user on the choice of the verbal mood. This research also presents comparative data on the use of the indicative mood in place of the subjunctive in Brazilian Portuguese and Canadian French, aiming to providing suggestions on language teaching

Analysis of the Al-PANI interfaces by complex impedance spectroscopy

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Contribution to the laboratory diagnosis of human cryptosporidiosis

A criptosporidiose humana é uma infecção causada pelo Cryptosporidium sp, um protozoário coccídio de patogenicidade emergente e responsável por severa e prostrante diarréia aquosa em humanos, principalmente em indivíduos imunodeprimidos. O diagnóstico, feito através da utilização de esfregaços de fezes submetidos a técnicas de concentração e coloração específica pela fucsina-carbólica tem oferecido bons resultados em nosso laboratório. Tendo em vista o longo tempo despendido para a observação dos esfregaços considerando-se a pequenez das formas e o contraste da coloração, realizamos modificações no procedimento técnico da coloração ácido-resistente que resultaram em sensível melhoria das preparações: a fucsina-carbólica passou a ser deixada sobre o esfregaço por período de 3 minutos (LENNETTE et al., 1985) e procedeu-se a substituição da solução de álcool-ácido sulfúrico a 5% (HENRIKSEN & POHLENZ, 1981) por solução de ácido clorídrico a 0,5% em álcool etílico 70%, por cerca de 2 minutos (contribuição original). Estas alterações promoveram melhor remoção do excesso de fucsina-carbólica, aumentando a eficiência da etapa de descoloração e consequentemente otimizando o contraste do processo de coloração. Nestas condições, as lâminas examinadas em microscópio óptico em aumentos de 250x e 1000x tiveram a visualização dos oocistos do protozoário facilitada, sendo os mesmos observados em contraste destacado com pigmentação intensa de cor rosa-avermelhada contra coloração de fundo azulada. Vale destacar que estas modificações oferecem vantagens de rápido processamento do material e facilidade de visualização do protozoário, diminuindo o tempo de microscopia, tornando a análise das lâminas mais rápida e menos cansativa, agilizando o diagnóstico.

Bottled mineral water as a potential source of antibiotic resistant bacteria

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Preparação de vidros e vitrocerâmicas de óxidos de metais pesados contendo prata: propriedades ópticas, estruturais e eletroquímicas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A imanência como lugar do ensino de filosofia

A intenção do presente artigo é pensar a problemática do ensino de filosofia a partir da obra de Deleuze e Guattari. Esses autores criaram uma série de conceitos, em seu fazer filosófico, para entender o que seria fazer filosofia, ou seja, para entender a atividade filosófica que se distanciasse de uma reflexão sobre alguma coisa e se fundasse em um ato de criação filosófica. Segundo os autores, existem quatro conceitos que corroboram para entender esse fazer filosófico, quais sejam: conceito, plano de imanência, personagem conceitual e problema. Tem-se como hipótese que tais conceitos podem contribuir para se pensar o ensino de filosofia na contemporaneidade de modo diferenciado do qual vem sendo tratado. Foi dada especial atenção a um desses conceitos: plano de imanência, engendrado na última obra conjunta desses autores, O que é a filosofia? (1997). Buscou-se, na obra desses autores, a caracterização de imanência e, consecutivamente, de plano de imanência para entender como se pode pensar o ensino de filosofia de forma diferenciada e de modo tal a distanciá-lo de uma adequação conceitual a um transcendente ou a um transcendental, a qual, no entender dos autores trabalhados, levaria o conceito de ensino a um dogmatismo conceitual. A proposta deste artigo é buscar uma saída para o problema, pensando o ensino de filosofia a partir da imanência mesma na qual este se produz.