Tapered bow-tie lasers for high energy Q-switched pulse generation

A new kind of Q switched laser, the bow tie laser is introduced. This type of laser permits large area facets at both ends so that generation of high optical powers involve low optical intensities to prevent optical damage. The incorporation of doubled tapered waveguide structure to the Q switched multicontact laser has increased the optical pulse energies and peak powers of the laser.

Demonstration of multi wavelength picosecond pulse generation with resonant RF drive using an monolithically integrated multi-grating cavity (MGC) laser

Multiwavelength pulses were generated using a monolithically integrated device. The device used is an integrated InGaAs/InGaAsP/InP multi-wavelength laser fabricated by selective area regrowth. The device self pulsated on all of the four wavelength channels. 48 ps pulses were obtained which were measured by a 50GHz oscilloscope and 32GHz photodiode which was not bandwidth limited. Simultaneous multi-wavelength pulse generation was also achieved.

Nonlinear pulse switching and compression in a dispersion-imbalanced loop mirror

The results of the high-quality nonlinear pulse compression of gain-switched laser diode pulses using a two-cascade compression scheme are presented. The scheme incorporates a dispersive delay line and a nonlinear pulse compressor based on a dispersion-imbalanced fiber loop mirror (DILM). It is demonstrated that the DILM can be also used for the pulse compression with a compression ratio of 10 or higher.

Multi-wavelength picosecond pulse generation using a monolithically integrated Multi-wavelength Grating Cavity (MGC) laser

Multi-wavelength picosecond pulses are demonstrated using a single monolithically integrated Multi-wavelength Grating Cavity (MGC) laser. This is achieved on two WDM wavelength channels at a repetition rate of 7.63 GHz.

High-power and picosecond pulse generation from a passively Q-switched tapered InGaAs/GaAs laser

Tapered waveguides have been used for enhancing pulse powers in Q-switched AlGaAs and InGaAsP lasers. This paper reports on passively Q-switched pulses with 1.53 W peak power and 41-ps FWHM from an InGaAs/GasAs (970 nm) double-contact tapered semiconductor laser in a well defined single-lobed far-field.

Blind frequency synchronisation for OFDM systems with pulse shaping

In multi-carrier systems, small carrier frequency offsets result in significant degradation of performance and this offset should be compensated before demodulation can be performed. In this paper, we consider a generic multi-carrier system with pulse shaping and estimate the frequency offset by exploiting the cyclostationarity of the received signal. By transforming the time domain signal to the cyclic correlation domain we are able to estimate the frequency offset without the aid of pilot symbols or the cyclic prefix. The Bayesian framework is used to obtain the estimate and we show how we can simplify the estimation process. © 1999 IEEE.

Analysis and performance assessment of 6-pulse inverter-fed 3-phase and 6-phase induction machines

The paper describes a model for a 6-phase induction motor driven by an inverter operating in a 6-pulse (square wave) mode. The model is implemented and performance, in terms of torque, current, efficiency and pulsating torque, compared to the performance of a 3-phase motor (both sine and 6-pulse supplied). The models are verified experimentally, in particular the efficiency performance, and it is illustrated that the improvement in inverter efficiency when in 6-pulse operating mode may improve the performance of the overall system. © 2005 IEEE.

A comparison of losses in small (<1 kW) drives using sine and space vector pulse width modulation schemes

this paper quantifies effects of using three different pulse width modulation (PWM) schemes on the losses in the inverter and induction motor of a 1 kW drive. Direct measurements of losses have been made with a calorimeter. Results show that for the inverter, discontinuous PWM excitation reduces losses by up to 15% compared to sine and symmetrical space vector PWM methods. However, at a low modulation index the greater harmonic content with discontinuous PWM increased motor losses by nearly 20%. This study demonstrates the importance of careful choice of modulation scheme to achieve high overall drive efficiency. © 2005 IEEE.

Waveguide lasers in Er:Yb-doped phosphate glass fabricated by femtosecond laser writing

Advanced waveguide lasers, operating both in continuous wave and pulsed regimes, have been realized in an active phosphate glass by direct writing with femtosecond laser pulses. Stable single mode operation was obtained; the laser provided more than 50 m W in single longitudinal and transverse mode operation with 21% slope efficiency. Furthermore, by combining a high gain waveguide and an innovated fiber-pigtailed saturable absorber based on carbon nanotubes, a mode-locked ring laser providing transform limited 1.6 ps pulses was demonstrated. © 2007 IEEE.

High-quality pulse compressor for WDM/OTDM applications

The paper reports the results of a high-quality pulse source incorporating a gain-switched laser diode followed by a novel compact two-cascade fibre compression scheme. The pulse compression scheme incorporates a dispersive delay line and a nonlinear pulse compressor based on a dispersion-imbalanced fibre loop mirror (DILM). We analyse and demonstrate for the first time significant improvement of the loop performance by means of the chirped pulse switching. As a result, the DILM provides high-quality nonlinear pulse compression as well as rejection of the nonsoliton component. In the experiment, 20ps pulses from a gain switched laser diode are compressed to a duration of 300fs at a repetition rate in range 70MHz-10GHz. The pulses are pedestal free and transform-limited. Spectral filtering of the output signal by means of a bandpass filter results in generation of wavelength-tuneable picosecond pulses with a duration defined by the filter bandwidth. Alternatively, signal filtering by an arrayed waveguide grating (AWG) results in multichannel picosecond pulse generation for WDM and OTDM applications. The pulse source is built of standard components and is of compact and potentially robust design.

Fluid mechanics of pulse pressure-gain combustors

The fluid dynamic operation of a valveless pulse combustor has been studied experimentally and numerically. Through phase-locked chemiluminescence and pressure measurements it is shown that mechanical energy is created periodically in the flame surface, with an efficiency of 1.6%. This mechanical energy leaves the pulse combustor through unsteady jets at the aerovalve inlet and the tailpipe exit stations. Two thermodynamically distinct flows are identified: a flow that is transported from inlet to exit and participates in combustion along the way, and a flow that is ingested and then ejected from the combustor without undergoing combustion. It is the latter of these two flows which has the greatest quantity of net work done on it. Copyright © 2008 by the American Institute of Aeronautics and Astronautics, Inc.