Crystal growth, Raman scattering and optical properties of the superconductor Cd2Re2O7(16O, 18O)/

Using the Physical Vapor Transport method, single crystals of Cd2Re207 have been grown, and crystals of dimensions up to 8x6x2 mm have been achieved. X-ray diffraction from a single crystal of Cd2Re207 has showed the crystal growth in the (111) plane. Powder X-ray diffraction measurements were performed on ^^O and ^^O samples, however no difference was observed. Assigning the space group Fd3m to Cd2Re207 at room temperature and using structure factor analysis, the powder X-ray diffraction pattern of the sample was explained through systematic reflection absences. The temperatiure dependence of the resistivity measurement of ^^O has revealed two structural phase transitions at 120 and 200 K, and the superconducting transition at 1.0 K. Using Factor Group Analysis on three different structiures of Cd2Re207, the number of IR and Raman active phonon modes close to the Brillouin zone centre have been determined and the results have been compared to the temperature-dependence of the Raman shifts of ^^O and ^*0 samples. After scaling (via removing Bose-Einstein and Rayleigh scattering factors from the scattered light) all spectra, each spectrum was fitted with a number of Lorentzian peaks. The temperature-dependence of the FWHM and Raman shift of mode Eg, shows the effects of the two structurjil phase transitions above Tc. The absolute reflectance of Cd2Re207 - '^O single crystals in the far-infrared spectral region (7-700 cm~^) has been measured in the superconducting state (0.5 K), right above the superconducting state (1.5 K), and in the normal state (4.2 K). Thermal reflectance of the sample at 0.5 K and 1.5 K indicates a strong absorption feature close to 10 cm~^ in the superconducting state with a reference temperature of 4.2 K. By means of Kramers-Kronig analysis, the absolute reflectance was used to calculate the optical conductivity and dielectric function. The real part of optical conductivity shows five distinct active phonon modes at 44, 200, 300, 375, and 575 cm~' at all temperatures including a Drude-like behavior at low frequencies. The imaginary part of the calculated dielectric function indicates a mode softening of the mode 44 cm~' below Tc.

Sexual behavior and factors affecting female reproduction in house and field crickets

The objective of this investigation was to clarify the adaptive significance of female sexual behaviours in the house cricket, Acheta domesticus, and the Texas field cricket, Gryllus integer. Experiments were focussed primarily on: nutritional factors affecting female reproductive success; the ontogeny of female sexual behaviours; female mating frequency and progeny production; and the pattern of sperm competition. Reproduction of singly mated female A. domesticus assigned to 3 nutritional regimes was compared . Females fed a vitamin and protein-enriched mouse chow, cannibalistic females, and starved females produced on the average, 513 , 200 and 68 offspring, respectively. Cannibals probably could not obtain the same amounts of essential nutrients as females fed mouse chow. Reabsorption of oocytes was likely the major factor contributing to the decreased reproduction of starved females. In addition, female !. domesticus fed mouse chow, but allowed constant access to males produced 11 times as many offspring than did females fed corn meal. Females fed corn meal probably could not absorb or synthesize enough dietary lipids, thus resulting in poor ovariole growth. Female !. domesticus first mate at an average adult age of 7 days, closely corresponding to when they first exhibit positive phonotaxis. Females mate repeatedly and often consume the externally attached spermatophore. In ~. domesticus, females allowed constant access to males produced significantly more offspring than did single maters. Similarly, doubly mated G. integer females produced more offspring than did single maters. This difference resulted largely from the failure of many single maters to reproduce. Remating by female crickets partly functions in offsetting the possibility of a failed initial mating. Nymph production increased significantly with the time the spermatophore was attached in singly mated ~. domesticus. Spermatophore consumption by the female was not affected by male guarding behaviour, and the interval between mating and eating of the spermatophore may often be shorter than the time required for maximum insemination. Some degree of sperm depletion in singly mated !. domesticus and G. integer may have occurred. The patterns of daily offspring production of singly and multiplymated females suggests that a factor provided by a male during mating stimulates female oviposition and/or egg production. Female crickets also might acquire nutrition from spermatophore consumption, a benefit that is augmented by female multiple mating. The electrophoretic examination of various allozymes in ~. integer did not permit determination of a pattern of sperm competition. However, the possibility of last male sperm predominance is related to male guarding behaviour.

Crystal Growth and Characterization of Li0.9Mo6O17

Purple bronze Li0.9Mo6O17 has attracted researchers for its low dimensionality and corresponding properties. Although it has been studied for nearly two decades, there are still some unsolved puzzles with this unique material. Single crystals of Li0.9Mo6O17 were grown using the temperature gradient flux technique in this research. The crystal growth was optimized by experimenting different conditions and good quality crystals were obtained. X-ray diffraction results have confirmed the right phase of the crystals. Resistivity measurements and magnetic susceptibility measurements were carried out, and anomalous electronic behaviors were found. All of the samples showed the metal-insulator transition near 20K, followed by behavior that differs from sample to sample: either superconducting, metallic or insulating behavior was observed below 2K. Li0.9Mo6O17 was considered as a quasi-one-dimensional crystal and also a superconducting crystal, which implies a dimensional crossover may occur at the metal-insulator transition. A two-band scenario of the Luttinger liquid model was used to fit the resistivity data and excellent results were achieved, suggesting that the Luttinger theory is a very good candidate for the explanation of the anomalous behavior of Li0.9Mo6O17. In addition, the susceptibility measurements showed Curie paramagnetism and some temperature independent paramagnetism at low temperature. The absence of any anomalous magnetic feature near 20K where the resistivity upturn takes place, suggests that a charge density wave mechanism, which has been proposed by some researchers, is not responsible for the unique properties of Li0.9Mo6O17.

The Co-occurrence of Depressive Symptoms and Alcohol Use for Adolescent Boys and Girls: An Investigation of the Role of Self-Regulation and Approach Behavior

While many studies have been conducted on adolescent depressive symptoms and alcohol use, much of the research has examined these behaviors separately rather than examining their co-occurrence within individuals. In the present study, adolescents (N = 4412; 49% female) were surveyed at four time points (grade 9, 10, 11, and 12) and growth mixture modeling was used to identify groups of individuals reporting various patterns of depressive symptoms and alcohol use across the high school years. Four groups were identified, including co-occurrence (higher depressive symptoms and higher alcohol use relative to peers, comprising 6.1 % of boys and 7.1 % of the girls in the sample), pure depressive symptoms (higher depressive symptoms and lower alcohol use; 12.7% of boys and 12.5% of girls), pure alcohol use (higher alcohol use and lower depressive symptoms; 20.9% of boys and 19.9% of girls), and low co-occurrence (lower depressive symptoms and alcohol use, 60.3% of boys and 60.5% of girls). Groups were compared on self-regulatory (i.e., delay of gratification) and approach behaviors. For both boys and girls, delay of gratification was the strongest predictor of group membership, with the co-occurrence group scoring the lowest and the low co-occurrence group the highest. This finding emphasizes the importance of assessing delay of gratification in the identification of high risk youth.

Growth factor activation of ErbB2/ErbB3 signaling pathways regulate the activity of Estrogen Receptors (ER)

La signalisation par l’estrogène a longtemps été considérée comme jouant un rôle critique dans le développement et la progression des cancers hormono-dépendants tel que le cancer du sein. Deux tiers des cancers du sein expriment le récepteur des estrogènes (ER) qui constitue un élément indiscutable dans cette pathologie. L’acquisition d’une résistance endocrinienne est cependant un obstacle majeur au traitement de cette forme de cancer. L’émergence de cancers hormono-indépendants peut est produite par l’activation de ER en absence d’estrogène, l’hypersensibilité du récepteur aux faibles concentrations plasmique d’estrogène ainsi que l’activation de ER par des modulateurs sélectifs. L’activité du ER est fortement influencée par l’environnement cellulaire tel que l’activation de voie de signalisation des facteurs de croissances, la disponibilité de protéines co-régulatrices et des séquences promotrices ciblées. Présentement, les études ont principalement considérées le rôle de ERα, cependant avec la découverte de ERβ, notre compréhension de la diversité des mécanismes potentiels impliquant des réponses ER-dépendantes s’est améliorée. L’activation des voies des kinases par les facteurs de croissance entraîne le développement d’un phénotype tumoral résistant aux traitements actuels. Nos connaissances des voies impliquées dans l’activation de ER sont restreintes. ERα est considéré comme le sous-type dominant et corrèle avec la plupart des facteurs de pronostic dans le cancer du sein. Le rôle de ERβ reste imprécis. Les résultats présentés dans cette thèse ont pour objectif de mieux comprendre l’implication de ERβ dans la prolifération cellulaire par l’étude du comportement de ERβ et ERα suite à l’activation des voies de signalisation par les facteurs de croissance. Nous démontrons que l’activation des récepteurs de surfaces de la famille ErbB, spécifiquement ErbB2/ErbB3, inhibe l’activité transcriptionnelle de ERβ, malgré la présence du coactivateur CBP, tout en activant ERα. De plus, l’inhibition de ERβ est attribuée à un résidu sérine (Ser-255) situé dans la région charnière, absente dans ERα. Des études supplémentaires de ErbB2/ErbB3 ont révélé qu’ils activent la voie PI3K/Akt ciblant à son tour la Ser-255. En effet, cette phosphorylation de ERβ par PI3K/Akt induit une augmentation de l’ubiquitination du récepteur qui promeut sa dégradation par le système ubiquitine-protéasome. Cette dégradation est spécifique pour ERβ. De façon intéressante, la dégradation par le protéasome requiert la présence du coactivateur CBP normalement requis pour l’activité transcriptionnelle des récepteurs nucléaires. Malgré le fait que l’activation de la voie PI3K/Akt corrèle avec une diminution de l’expression des gènes sous le contrôle de ERβ, on observe une augmentation de la prolifération des cellules cancéreuses. L’inhibition de la dégradation de ERβ réduit cette prolifération excessive causée par le traitement avec Hrgβ1, un ligand de ErbB3. Un nombre croissant d’évidences indique que les voies de signalisations des facteurs de croissance peuvent sélectivement réguler l’activité transcriptionnelle de sous-types de ER. De plus, le ratio ERα/ERβ dans les cancers du sein devient un outil de diagnostique populaire afin de déterminer la sévérité d’une tumeur. En conclusion, la caractérisation moléculaire du couplage entre la signalisation des facteurs de croissance et la fonction des ERs permettra le développement de nouveaux traitements afin de limiter l’apparition de cellules tumorales résistantes aux thérapies endocriniennes actuelles.

Soft Surveillance: The Growth of Mandatory Volunteerism in Collecting Personal Information “Hey Buddy Can You Spare a DNA?”

Le développement accéléré des technologies de communication, de saisie et de traitement de l’information durant les dernières années décennies ouvre la voie à de nouveaux moyens de contrôle social. Selon l’auteur Gary Marx ceux-ci sont de nature non coercitive et permettent à des acteurs privés ou publics d’obtenir des informations personnelles sur des individus sans que ceux-ci y consentent ou mêmes sans qu’ils en soient conscients. Ces moyens de contrôle social se fondent sur certaines valeurs sociales qui sont susceptibles de modifier le comportement des individus comme le patriotisme, la notion de bon citoyen ou le volontarisme. Tout comme les moyens coercitifs, elles amènent les individus à adopter certains comportements et à divulguer des informations précises. Toutefois, ces moyens se fondent soit sur le consentement des individus, consentement qui est souvent factice et imposée, soit l’absence de connaissance du processus de contrôle par les individus. Ainsi, l’auteur illustre comment des organisations privées et publiques obtiennent des informations privilégiées sur la population sans que celle-ci en soit réellement consciente. Les partisans de tels moyens soulignent leur importance pour la sécurité et le bien publique. Le discours qui justifie leur utilisation soutient qu’ils constituent des limites nécessaires et acceptables aux droits individuels. L’emploi de telles méthodes est justifié par le concept de l’intérêt public tout en minimisant leur impact sur les droits des individus. Ainsi, ces méthodes sont plus facilement acceptées et moins susceptibles d’être contestées. Toutefois, l’auteur souligne l’importance de reconnaître qu’une méthode de contrôle empiète toujours sur les droits des individus. Ces moyens de contrôle sont progressivement intégrés à la culture et aux modes de comportement. En conséquence, ils sont plus facilement justifiables et certains groupes en font même la promotion. Cette réalité rend encore plus difficile leur encadrement afin de protéger les droits individuels. L’auteur conclut en soulignant l’important décalage moral derrière l’emploi de ces méthodes non-coercitives de contrôle social et soutient que seul le consentement éclairé des individus peut justifier leur utilisation. À ce sujet, il fait certaines propositions afin d’encadrer et de rendre plus transparente l’utilisation de ces moyens de contrôle social.

The inflammatory role of angiogenic growth factors : a neutrophil perspective

De par sa présence dans tous les vaisseaux sanguins, l'endothélium joue un rôle clef dans le processus d’hémostase, tant par sa libération de facteurs anticoagulants que par ses changements protéiques qui permettent à l’organisme de déclencher la réparation tissulaire. La fonction anticoagulante de l’endothélium peut être mise en défaut en cas d’atteinte de son intégrité, entrainant la formation de thrombus, le rejet précoce de greffes ou encore l’induction de l’athérosclérose. L’intégrité de l’endothélium est donc capitale pour la prévention de nombreuses maladies cardiovasculaires. Chez l’adulte, les cellules endothéliales (CE), normalement quiescentes, sont rapidement activées en cas d’hypoxie ou d’inflammation, leur permettant ainsi d’amorcer le processus angiogénique comme suit: Tout d’abord, l’induction de l’hyperperméabilité vasculaire permet l’extravasation des protéines plasmatiques. Ensuite, la dégradation de la lame basale par des métalloprotéases permet aux CE de se détacher, de proliférer, de migrer et de s’organiser pour former l’ébauche du futur vaisseau. La dernière étape consiste en la maturation du vaisseau, c’est-à-dire son recouvrement par des cellules murales, telles que les cellules musculaires lisses et les péricytes. Ces processus sont régulés par de nombreux facteurs angiogéniques tels que les membres de la famille Notch, du vascular endothelial growth factor (VEGF), du fibroblast growth factor (FGF), des angiopoïétines, et des matrix metalloproteases (MMP). L’angiogenèse pathologique, soit une insuffisance ou un excès de vascularisation, est impliquée dans les blessures chroniques, les accidents cardiovasculaires, les pathologies coronariennes artérielles, les pathologies tumorales, l’arthrite rhumatoïde, la rétinopathie diabétique, l’athérosclérose, le psoriasis et l’asthme. Ces pathologies sont souvent issues d’une dérégulation de l’activité endothéliale, fréquemment observée conjointement à l’expression continue de molécules d’adhésion leucocytaires, à l’augmentation de la perméabilité vasculaire, et aux anomalies de la vasoréactivité. L’activation non-contrôlée de l’endothélium entraîne ainsi une inflammation chronique et la formation de structures vasculaires anarchiques. Les premiers leucocytes à répondre à l’appel inflammatoire sont les neutrophiles. Equippées d’une panoplie de produits antibactériens puissants mais aussi nocifs pour les tissus qui les entourent, ces cellules polylobées participent à chaque étape du processus inflammatoire, depuis l’induction de l’hyperperméabilité vasculaire jusqu’à la résolution. En effet, grâce à leurs récepteurs, les neutrophiles détectent et interprètent les signaux biochimiques présents dans la circulation et à la surface de l’endothélium, et libèrent aussi leurs propres médiateurs tels le VEGF, les MMP, et l’interleukine-8 (IL-8), dont les effets sont à la fois paracrines et autocrines. Existent-ils d’autres modulateurs typiques de la fonction endothéliale capables d’influencer le comportement des neutrophiles? En effet, notre laboratoire a démontré que chez l’humain, une stimulation directe aux angiopoïétines incitait les neutrophiles à adhérer aux CE, à migrer, à synthétiser et à relâcher l’IL-8, voire même à vivre plus longtemps. La présence du récepteur des angiopoïétines, Tie2, à la surface des neutrophiles laisse présager que la famille possèderait d’autres fonctions leucocytaires encore non-identifiées. Par ailleurs, dans un modèle classique de l’angiogenèse in vivo (matrigel), nous avons observé que sous l’effet du FGF1 et 2, les ébauches des nouveaux vaisseaux étaient parfois accompagnées d’une infiltration de cellules granulocytaires. Ainsi, en partant de ces observations, l’objectif de nos études (présentées ci-après) était d’approfondir nos connaissances sur la relation entre neutrophiles et facteurs angiogéniques, notamment les FGF et les angiopoïétines. Par tests in vitro, nous avons confirmé que les neutrophiles humains exprimaient plusieurs récepteurs du FGF (FGFR1-4) d’une façon hétérogène, et qu’ils migraient vers un gradient des ligands FGF1 et 2. Par ailleurs, nous nous sommes intéressés aux voies de signalisation inflammatoires activées par les ligands FGF1, FGF2, Ang1 et Ang2. Grâce à une stratégie génique ciblant 84 gènes inflammatoires, nous avons identifié plusieurs cibles d’intérêt touchées par Ang1, dont certains membres de la famille de l’IL-1, alors qu’aucun des gènes testés n’avait changé de façon significative sous l’effet des FGF ou d’Ang2. Suite à des cinétiques approfondies, nous avons démontré qu’Ang1 stimulait la transcription de l’ARN messager de l’IL-1β, et augmentait simultanément la quantité de protéine immature (pro-IL-1β; inactive) et clivée (IL-1β « mature »; active). En parallèle, Ang1 augmentait la sécrétion de l’antagoniste naturel de l’IL-1β, l’IL-1RA, sans pour autant stimuler la relâche de l’IL-1β. A l’instar des endotoxines bactériennes dont les effets liés à l’IL-1 dépendaient de la kinase p38, ceux d’Ang1 découlaient presque entièrement des voies de signalisation du p42/44.

Vacancy-assisted domain-growth in asymmetric binary alloys: A Monte Carlo Study

A Monte Carlo simulation study of the vacancy-assisted domain growth in asymmetric binary alloys is presented. The system is modeled using a three-state ABV Hamiltonian which includes an asymmetry term. Our simulated system is a stoichiometric two-dimensional binary alloy with a single vacancy which evolves according to the vacancy-atom exchange mechanism. We obtain that, compared to the symmetric case, the ordering process slows down dramatically. Concerning the asymptotic behavior it is algebraic and characterized by the Allen-Cahn growth exponent x51/2. The late stages of the evolution are preceded by a transient regime strongly affected by both the temperature and the degree of asymmetry of the alloy. The results are discussed and compared to those obtained for the symmetric case.

Fragile-glass behavior of a short-range p-spin model

We propose a short-range generalization of the p-spin interaction spin-glass model. The model is well suited to test the idea that an entropy collapse is at the bottom line of the dynamical singularity encountered in structural glasses. The model is studied in three dimensions through Monte Carlo simulations, which put in evidence fragile glass behavior with stretched exponential relaxation and super-Arrhenius behavior of the relaxation time. Our data are in favor of a Vogel-Fulcher behavior of the relaxation time, related to an entropy collapse at the Kauzmann temperature. We, however, encounter difficulties analogous to those found in experimental systems when extrapolating thermodynamical data at low temperatures. We study the spin-glass susceptibility, investigating the behavior of the correlation length in the system. We find that the increase of the relaxation time is accompanied by a very slow growth of the correlation length. We discuss the scaling properties of off-equilibrium dynamics in the glassy regime, finding qualitative agreement with the mean-field theory.

Mn2þ-induced room-temperature ferromagnetism and spin-glass behavior in hydrothermally grown Mn-doped ZnO nanorods

The magnetic properties of Mn-doped ZnO (ZnO:Mn) nanorods grown by hydrothermal process at a temperature of 200 8C and a growth time of 3 h have been studied. The samples were characterized by using powder X-ray diffraction with Rietveld refinement, scanning electron microscopy, energy-dispersive X-ray analysis and SQUID magnetometry. Mn (3 wt%) and (5 wt%)-doped ZnO samples exhibit paramagnetic and ferromagnetic behavior, respectively, at room temperature. The spin-glass behavior is observed from the samples with respect to the decrease of temperature. At 10 K, both samples exhibit a hysteresis loop with relatively low coercivity. The room-temperature ferromagnetism in 5 wt% Mn-doped ZnO nanorods is attributed to the increase in the specific area of grain boundaries, interaction between dopant Mn2þ ions substituted at Zn2þ site and the interaction between Mn2þ ions and Zn2þ ions from the ZnO host lattice

Behavior of geopolymer concrete exposed to elevated temperatures

The research in the area of geopolymer is gaining momentum during the past 20 years. Studies confirm that geopolymer concrete has good compressive strength, tensile strength, flexural strength, modulus of elasticity and durability. These properties are comparable with OPC concrete.There are many occasions where concrete is exposed to elevated temperatures like fire exposure from thermal processor, exposure from furnaces, nuclear exposure, etc.. In such cases, understanding of the behaviour of concrete and structural members exposed to elevated temperatures is vital. Even though many research reports are available about the behaviour of OPC concrete at elevated temperatures, there is limited information available about the behaviour of geopolymer concrete after exposure to elevated temperatures. A preliminary study was carried out for the selection of a mix proportion. The important variable considered in the present study include alkali/fly ash ratio, percentage of total aggregate content, fine aggregate to total aggregate ratio, molarity of sodium hydroxide, sodium silicate to sodium hydroxide ratio, curing temperature and curing period. Influence of different variables on engineering properties of geopolymer concrete was investigated. The study on interface shear strength of reinforced and unreinforced geopolymer concrete as well as OPC concrete was also carried out. Engineering properties of fly ash based geopolymer concrete after exposure to elevated temperatures (ambient to 800 °C) were studied and the corresponding results were compared with those of conventional concrete. Scanning Electron Microscope analysis, Fourier Transform Infrared analysis, X-ray powder Diffractometer analysis and Thermogravimetric analysis of geopolymer mortar or paste at ambient temperature and after exposure to elevated temperature were also carried out in the present research work. Experimental study was conducted on geopolymer concrete beams after exposure to elevated temperatures (ambient to 800 °C). Load deflection characteristics, ductility and moment-curvature behaviour of the geopolymer concrete beams after exposure to elevated temperatures were investigated. Based on the present study, major conclusions derived could be summarized as follows. There is a definite proportion for various ingredients to achieve maximum strength properties. Geopolymer concrete with total aggregate content of 70% by volume, ratio of fine aggregate to total aggregate of 0.35, NaOH molarity 10, Na2SiO3/NaOH ratio of 2.5 and alkali to fly ash ratio of 0.55 gave maximum compressive strength in the present study. An early strength development in geopolymer concrete could be achieved by the proper selection of curing temperature and the period of curing. With 24 hours of curing at 100 °C, 96.4% of the 28th day cube compressive strength could be achieved in 7 days in the present study. The interface shear strength of geopolymer concrete is lower to that of OPC concrete. Compared to OPC concrete, a reduction in the interface shear strength by 33% and 29% was observed for unreinforced and reinforced geopolymer specimens respectively. The interface shear strength of geopolymer concrete is lower than ordinary Portland cement concrete. The interface shear strength of geopolymer concrete can be approximately estimated as 50% of the value obtained based on the available equations for the calculation of interface shear strength of ordinary portland cement concrete (method used in Mattock and ACI). Fly ash based geopolymer concrete undergoes a high rate of strength loss (compressive strength, tensile strength and modulus of elasticity) during its early heating period (up to 200 °C) compared to OPC concrete. At a temperature exposure beyond 600 °C, the unreacted crystalline materials in geopolymer concrete get transformed into amorphous state and undergo polymerization. As a result, there is no further strength loss (compressive strength, tensile strength and modulus of elasticity) in geopolymer concrete, whereas, OPC concrete continues to lose its strength properties at a faster rate beyond a temperature exposure of 600 °C. At present no equation is available to predict the strength properties of geopolymer concrete after exposure to elevated temperatures. Based on the study carried out, new equations have been proposed to predict the residual strengths (cube compressive strength, split tensile strength and modulus of elasticity) of geopolymer concrete after exposure to elevated temperatures (upto 800 °C). These equations could be used for material modelling until better refined equations are available. Compared to OPC concrete, geopolymer concrete shows better resistance against surface cracking when exposed to elevated temperatures. In the present study, while OPC concrete started developing cracks at 400 °C, geopolymer concrete did not show any visible cracks up to 600 °C and developed only minor cracks at an exposure temperatureof 800 °C. Geopolymer concrete beams develop crack at an early load stages if they are exposed to elevated temperatures. Even though the material strength of the geopolymer concrete does not decrease beyond 600 °C, the flexural strength of corresponding beam reduces rapidly after 600 °C temperature exposure, primarily due to the rapid loss of the strength of steel. With increase in temperature, the curvature at yield point of geopolymer concrete beam increases and thereby the ductility reduces. In the present study, compared to the ductility at ambient temperature, the ductility of geopolymer concrete beams reduces by 63.8% at 800 °C temperature exposure. Appropriate equations have been proposed to predict the service load crack width of geopolymer concrete beam exposed to elevated temperatures. These equations could be used to limit the service load on geopolymer concrete beams exposed to elevated temperatures (up to 800 °C) for a predefined crack width (between 0.1mm and 0.3 mm) or vice versa. The moment-curvature relationship of geopolymer concrete beams at ambient temperature is similar to that of RCC beams and this could be predicted using strain compatibility approach Once exposed to an elevated temperature, the strain compatibility approach underestimates the curvature of geopolymer concrete beams between the first cracking and yielding point.

A crack on the interface of piezo-electric bodies

Singularities of elastic and electric fields are investigated at the tip of a crack on the interface of two anisotropic piezo-electric media under various boundary conditions on the crack surfaces. The Griffith formulae are obtained for increments of energy functionals due to growth of the crack and the notion of the energy release matrix is introduced. Normalization conditions for bases of singular solution are proposed to adapt them to the energy, stress, and deformation fracture criteria. Connections between these bases are determined and additional properties of the deformation basis related to the notion of electric surface enthalpy are established.

Punching Shear Behavior of UHPC Flat Slabs

At the Institute of Structural Engineering of the Faculty of Civil Engineering, Kassel University, series tests of slab-column connection were carried out, subjected to concentrated punching load. The effects of steel fiber content, concrete compressive strength, tension reinforcement ratio, size effect, and yield stress of tension reinforcement were studied by testing a total of six UHPC slabs and one normal strength concrete slab. Based on experimental results; all the tested slabs failed in punching shear as a type of failure, except the UHPC slab without steel fiber which failed due to splitting of concrete cover. The post ultimate load-deformation behavior of UHPC slabs subjected to punching load shows harmonic behavior of three stages; first, drop of load-deflection curve after reaching maximum load, second, resistance of both steel fibers and tension reinforcement, and third, pure tension reinforcement resistance. The first shear crack of UHPC slabs starts to open at a load higher than that of normal strength concrete slabs. Typically, the diameter of the punching cone for UHPC slabs on the tension surface is larger than that of NSC slabs and the location of critical shear crack is far away from the face of the column. The angle of punching cone for NSC slabs is larger than that of UHPC slabs. For UHPC slabs, the critical perimeter is proposed and located at 2.5d from the face of the column. The final shape of the punching cone is completed after the tension reinforcement starts to yield and the column stub starts to penetrate through the slab. A numerical model using Finite Element Analysis (FEA) for UHPC slabs is presented. Also some variables effect on punching shear is demonstrated by a parametric study. A design equation for UHPC slabs under punching load is presented and shown to be applicable for a wide range of parametric variations; in the ranges between 40 mm to 300 mm in slab thickness, 0.1 % to 2.9 % in tension reinforcement ratio, 150 MPa to 250 MPa in compressive strength of concrete and 0.1 % to 2 % steel fiber content. The proposed design equation of UHPC slabs is modified to include HSC and NSC slabs without steel fiber, and it is checked with the test results from earlier researches.

Does interpersonal behavior of psychotherapy trainees differ in private and professional relationships?

• Aim: The present study aimed to evaluate the effect of trainees’ interpersonal behavior on work involvement (WI) and compared their social behavior within professional and private relationships as well as between different psychotherapeutic orientations. • Methods: The interpersonal scales of the Intrex short-form questionnaire and the Work Involvement Scale (WIS) were used to evaluate two samples of German psychotherapy trainees in psychoanalytic, psychodynamic, and cognitive behavioral therapy training. Trainees from Sample 1 (N = 184) were asked to describe their interpersonal behavior in relation to their patients when filling out the Intrex, whereas trainees from Sample 2 (N = 135) were asked to describe the private relationship with a significant other. • Results: Interpersonal affiliation in professional relationships significantly predicted the level of healing involvement, while stress involvement was predicted by interpersonal affiliation and interdependence in trainees’ relationships with their patients. Social behavior within professional relationships provided higher correlations with WI than private interpersonal behavior. Significant differences were found between private and professional relation settings in trainees’ interpersonal behavior with higher levels of affiliation and interdependence with significant others. Differences between therapeutic orientation and social behavior could only be found when comparing trainees’ level of interdependence with the particular relationship setting. • Conclusion: Trainees’ interpersonal level of affiliation in professional relationships is a predictor for a successful psychotherapeutic development. Vice versa, controlling behavior in professional settings can be understood as a risk factor against psychotherapeutic growth. Both results strengthen an evidence-based approach for competence development during psychotherapy training.

Simulation of delamination in composites under quasi-static and fatigue loading using cohesive zone models

Es desenvolupa una eina de disseny per l'anàlisi de la tolerància al dany en composites. L'eina pot predir el inici i la propagació de fisures interlaminars. També pot ser utilitzada per avaluar i planificar la necessitat de reparar o reemplaçar components durant la seva vida útil. El model desenvolupat pot ser utilitzat tan per simular càrregues estàtiques com de fatiga. El model proposat és un model de dany termodinàmicament consistent que permet simular la delaminació en composites sota càrregues variables. El model es formula dins el context de la Mecànica del Dany, fent ús dels models de zona cohesiva. Es presenta un metodologia per determinar els paràmetres del model constitutiu que permet utilitzar malles d'elements finits més bastes de les que es poden usar típicament. Finalment, el model és també capaç de simular la delaminació produïda per càrregues de fatiga.