Porosity and sound velocity measured in sediment core CIROS-1

The CIROS-1 drillhole, which in 1986 reached a depth of 700 m below the seafloor, is still the only deep hole that can provide information on the velocity structure of the upper crust in McMurdo Sound and the Ross Sea, Antarctica. A careful review and quality control of the downhole logging data of CIROS-1 resulted in a new porosity depth function that is consistent with porosity data from the MSSTS-1 and CRP-1 drillholes. Using existing porosity-velocity equations, it was possible for the first time to obtain reliable velocity information for the upper 700 m of strata off the Victoria Land coast. The calculated synthetic seismograms, based on downhole velocity and density data, fit very well with the existing seismic lines IT90A-71, PD90-12, and NBP9601-89. The quality of the correlation confirms that the average velocity of the top 700 m of strata is about 2 000-2 300 m/s, and not 2 800-3 000 m/s, as was previously assumed. In consequence, these distinctly lower velocities result in shallower depths for the seismic unconformities V3/V4 andV4/V5 and thus may have important implications for further drilling off Cape Roberts.

(Table 1) Summary of basalt unit thickness, vesicularity, number of flow units, and average porosity at ODP Site 135-839

An inflatable drill-string packer was used at Site 839 to measure the bulk in-situ permeability within basalts cored in Hole 839B. The packer was inflated at two depths, 398.2 and 326.9 mbsf; all on-board information indicated that the packer mechanically closed off the borehole, although apparently the packer hydraulically sealed the borehole only at 398.2 mbsf. Two pulse tests were run at each depth, two constant-rate injection tests were run at the first set, and four were run at the second. Of these, only the constant-rate injection tests at the first set yielded a permeability, calculated as ranging from 1 to 5 * 10**-12 m**2. Pulse tests and constant-rate injection tests for the second set did not yield valid data. The measured permeability is an upper limit; if the packer leaked during the experiments, the basalt would be less permeable. In comparison, permeabilities measured at other Deep Sea Drilling Project and Ocean Drilling Program sites in pillow basalts and flows similar to those measured in Hole 839B are mainly about 10**-13 to 10**-14 m**2. Thus, if our results are valid, the basalts at Site 839 are more permeable than ocean-floor basalts investigated elsewhere. Based on other supporting evidence, we consider these results to be a valid measure of the permeability of the basalts. Temperature data and the geochemical and geotechnical properties of the drilled sediments all indicate that the site is strongly affected by fluid flow. The heat flow is very much less than expected in young oceanic basalts, probably a result of rapid fluid circulation through the crust. The geochemistry of pore fluids is similar to that of seawater, indicating seawater flow through the sediments, and sediments are uniformly underconsolidated for their burial depth, again indicating probable fluid flow. The basalts are highly vesicular. However, the vesicularity can only account for part of the average porosity measured on the neutron porosity well log; the remainder of the measured porosity is likely present as voids and fractures within and between thin-bedded basalts. Core samples, together with porosity, density, and resistivity well-log data show locations where the basalt section is thin bedded and probably has from 15% to 35% void and fracture porosity. Thus, the measured permeability seems reasonable with respect to the high measured porosity. Much of the fluid flow at Site 839 could be directed through highly porous and permeable zones within and between the basalt flows and in the sediment layer just above the basalt. Thus, the permeability measurements give an indication of where and how fluid flow may occur within the oceanic crust of the Lau Basin.

Short-term guidelines to improve crumb rubber modified asphalt concrete pavements. Final report.

Texas Department of Transportation, Austin

Design and construction of asphalt paving materials with crumb rubber modifier : state of the practice /

"May 1992."

Eutectic solidification and its role in casting porosity formation

Understanding and controlling the eutectic solidification process in Al-Si alloys permits prediction of the formation of casting porosity, eventually leading to methods for its control and elimination. In addition, it enables control of eutectic structure, silicon morphology, and eutectic grain size to further improve the alloy properties. This paper presents the current understanding of eutectic solidification in hypoeutectic Al-Si foundry alloys and the relationship between eutectic solidification and porosity formation. New concepts in engineering eutectic solidification are also explored.