An evaluation of mark and recapture techniques for estimating tigerfish biomass in Lake Kariba

The effectiveness of 2 mark and recapture techniques was evaluated using tiger fish, Hydrocynus vittatus. The 2 techniques used were: tagging with a plastic tag and fluorescent spray marking. While the tagging method resulted as the logical method to use within the constraints of the tiger fish study, it cannot be considered completely reliable for the estimation of population size in Lake Kariba.

Advanced techniques for diagnostics and control applied to particle accelerators

201 p.

Influence of oxygen plasma treatment on properties of ZrO2 films prepared by e-beam evaporation techniques

Zirconia films were prepared by e-beam evaporation, and oxygen plasma treatment was used to modify film properties. Spectrophotometry, x-ray diffractometry (XRD), and atomic force microscopy were used to characterize refractive index, extinction coefficient, rnicrostructure, and surface roughness, respectively. The experimental results indicate that both refractive index and extinction coefficient of the films were reduced slightly after oxygen plasma treatment, with the decrease of intrinsic stress and surface roughness. From XRD spectra, the intensity decrease of the T(110) diffraction peak was clearly observed after the treatment, which was caused by the restructuring of the film atoms. (C) 2008 Elsevier Ltd. All rights reserved.

Techniques for fabrication of large-size graded reflectivity mirrors

According to the parameter requirements of a graded reflectivity mirror with a Gaussian profile, the layer structure and the mask pattern are designed using a graded-thickness middle layer. The mask and the automatic mask-switchover equipment are designed considering the actual requirement of the thin films and the specific deposit facility. The uniformity of the layer thickness is analyzed. The measurement results indicate that samples prepared with this technique are basically in accordance with the design parameter. The scattering effect between the material molecules and the mask, thickness errors, and the alignment error between the mask and the substrate are the main factors that influence the deposit result. (c) 2008 Society of Photo-Optical Instrumentation Engineers. [DOI: 10.1117/1.3027595]

Hot-pressed translucent aluminum oxynitride (AlON) ceramics

AlON with a composition of Al23O27N5 was prepared by hot pressing at temperatures lower than 1900°C. The microstructures and final properties, including both mechanical properties and optical properties, of the sintered specimens were studied. The results showed that sintering temperature had a great influence on the densification of specimens and could lead to very different properties, especially the optical transmittance and the maximum infrared transmission.

Description of NRA tracking studies: tracking techniques and fish counter technology

The study began on the 7th January 1991 and was completed in June 1991. Two reports have been produced. This report published as R&D Note 33 describes NRA tracking studies, tracking techniques and fish counter technology. The second report published as R&D Note 34 evaluates NRA tracking studies and recommends future research. The latter will be used solely for NRA management purposes. This report briefly outlines the programme of the NRA, placing the Fisheries programme in the context of the work of the NRA as a whole, and viewing the tracking work against the broader requirements of the NRA Fisheries research programme. Two techniques currently exist for studying the detailed timing and extent of movements of adult salmon: tracking of individually identifiable fish, and counting the numbers of fish moving past a fixed point in the river. Further details of these techniques and their development are given in Sections 2 and 3. Section 4 summarises and assesses completed and current NRA tracking Studies. Complete project descriptions for the studies are contained in Appendix A. Section 5 discusses the scientific content of these studies in relation to similar work carried out elsewhere in the UK. Section 6 details the future development of tracking techniques. Tracking work on migratory salmonids has tended to concentrate largely upon the movements of adult salmon. Much of this report will therefore be concerned with salmon tracking studies. NRA studies involving sea trout are referred to where appropriate. The methodological problems of sea trout tracking studies are summarised in Section 2.1.3.

Lionfish dissection: techniques and applications

Dissection can provide unique information on the physiology, biology and ecology of organisms. This document describes protocols for dissecting lionfish (Pterois volitans and P. miles). Protocols were developed to provide guidance to trained research personnel. Lionfish are native to the Indo-Pacific, but have become established in marine habitats within the Western Atlantic, Gulf of Mexico and Caribbean. The protocols described within this document were designed to help standardize handling and dissection methodologies for these species, with the goal of improving the coordination of research (e.g., Lionfish Tissue Repository; Appendix V). We focus on dissection methods, which yield data that contribute to our understanding of lionfish biology and ecology. By pairing dissection information with environmental and biotic data, researchers and managers can better understand lionfish population structure and dynamics, age and growth, reproductive biology, and food web ecology on various temporal and spatial scales.

Evaluation of bioelectrical impedance analysis and Fulton’s condition factor as nonlethal techniques for estimating short-term responses in postsmolt Atlantic salmon (Salmo salar) to food availabili

We evaluated measures of bioelectrical impedance analysis (BIA) and Fulton’s condition factor (K) as potential nonlethal indices for detecting short-term changes in nutritional condition of postsmolt Atlantic salmon (Salmo salar). Fish reared in the laboratory for 27 days were fed, fasted, or fasted and then refed. Growth rates and proximate body composition (protein, fat, water) were measured in each fish to evaluate nutritional status and condition. Growth rates of fish responded rapidly to the absence or reintroduction of food, whereas body composition (% wet weight) remained relatively stable owing to isometric growth in fed fish and little loss of body constituents in fasted fish, resulting in nonsignificant differences in body composition among feeding treatments. The utility of BIA and Fulton’s K as condition indices requires differences in body composition. In our study, BIA measures were not significantly different among the three feeding treatments, and only on the final day of sampling was K of fasted vs. fed fish significantly different. BIA measures were correlated with body composition content; however, wet weight was a better predictor of body composition on both a content and concentration (% wet weight) basis. Because fish were growing isometrically, neither BIA nor K was well correlated with growth rate. For immature fish, where growth rate, rather than energy reserves, is a more important indicator of fish condition, a nonlethal index that reflects shortterm changes in growth rate or the potential for growth would be more suitable as a condition index than either BIA measures or Fulton�

The use of multibeam sonar mapping techniques to refine population estimates of the endangered white abalone (Haliotis sorenseni)

Multibeam sonar mapping techniques provide detailed benthic habitat information that can be combined with the data on species-specific habitat preferences to provide highly accurate calculations of populations in a particular area. The amount of suitable habitat available for the endangered white abalone (Haliotis sorenseni) was quantified to aid in obtaining an accurate estimate of the number of remaining individuals at two offshore banks and one island site off the coast of southern California. Habitat was mapped by using multibeam sonar survey techniques and categorized by using rugosity and topographic position analysis. Abalone densities were evaluated by using a remotely operated vehicle and video transect methods. The total amount of suitable habitat at these three sites was far greater than that previously estimated. Therefore, although present estimates of white abalone densities are several orders of magnitude lower than historic estimates, the total population is likely larger than previously reported because of the additional amount of habitat surveyed in this study.

Identificação da formação de titanato de bário a partir de mistura reacional calcinada em diferentes temperaturas via difração de raios X, espectroscopia fotoacústica e análise térmica

Os materiais ferroelétricos têm sido utilizados em muitas áreas da tecnologia e da ciência, pois possuem um grande número de aplicações, como: sensores; transdutores; capacitores; dispositivos ópticos; dentre outras. A busca por novos materiais cerâmicos ferroelétricos tem sido grande. Um dos materiais cerâmicos ferroelétricos mais estudados é o titanato de bário (BT). São vários os métodos de produção e caracterização do titanato de bário. Neste trabalho, pós cerâmicos de titanato de bário foram obtidos por reação do estado sólido a partir de misturas reacionais calcinadas em diferentes temperaturas entre 400C e 900C. Foram três as misturas reacionais: não dopadas; dopadas com 1%; e dopadas com 5% de dióxido de cério (CeO2). A identificação da formação do BT, nos pós cerâmicos produzidos, foi feita a partir de três técnicas de caracterização: difração de raios X (DRX); espectroscopia fotoacústica (PAS); e técnicas de análise térmica. Com a técnica DRX, difratogramas mostraram que a plena formação do titanato de bário ocorreu a partir da temperatura de calcinação de 700C. Para a amostra não dopada com cério e calcinada a 800C, houve deslocamento de todos os picos de difração. Nas amostras dopadas com dióxido de cério houve deslocamento de todos os picos de difração, em relação as amostras não dopadas. Observou-se também que nas amostras dopadas com 5% de CeO2, e calcinadas a 700C e 800C, resíduos de dióxido de cério foram observados nos difratogramas. Com a técnica PAS, espectros de absorção foram obtidos. Foi possível observar uma grande diferença de absorção da amostra calcinada a 600 e 630C, indicando a formação do titanato de bário a partir da temperatura de 630C, nas amostras sem a dopagem dióxido de cério. Houve um alargamento nas bandas de absorção a partir da temperatura de 600C, quando o dióxido de cério entrou na matriz. Foi também possível determinar as energias de band-gap das amostras utilizando o método de Tauc. Com as técnicas de análise térmica, em especial através da técnica termogravimétrica (TG/DTG), foi comprovado que até 400C não havia formação de titanato de bário. Visto que nesta temperatura de calcinação houve a maior perda de massa durante a rampa de aquecimento. O início da formação do titanato de bário foi observado a partir da temperatura de calcinação de 500C, assim como nas técnicas DRX e PAS. Portanto, com os resultados apresentados, foi demonstrada a identificação da formação do titanato de bário nas misturas reacionais calcinadas, com auxílio das potencialidades das três técnicas utilizadas.