Development of advanced cell/tissue culture systems, based on enhanced polymeric scaffolds and sophisticated bioreactors, for tissue engineering applications

Programa Doutoral em Engenharia Biomédica

Modelação, simulação e implementação de agitação acústica para aplicações em microfluídica

Tese de Doutoramento (Programa Doutoral em Engenharia Biomédica)

A bio-inspired computational model for motion detection

Tese de Doutoramento (Programa Doutoral em Engenharia Biomédica)

High performance screen printable lithium-ion battery cathode ink based on C-LiFePO4

Lithium-ion battery cathodes have been fabricated by screen-printing through the development of CLiFePO4 inks. It is shown that shear thinning polymer solutions in N-methyl-2-pyrrolidone (NMP) with Newtonian viscosity above 0.4 Pa s are the best binders for formulating a cathode paste with satisfactory film forming properties. The paste shows an elasticity of the order of 500 Pa and, after shear yielding, shows an apparent viscosity of the order of 3 Pa s for shear rates corresponding to those used during screen-printing. The screen-printed cathode produced with a thickness of 26 mm shows a homogeneous distribution of the active material, conductive additive and polymer binder. The total resistance and diffusion coefficient of the cathode are 450 V and 2.5 10 16cm2 s 1, respectively. The developed cathodes show an initial discharge capacity of 48.2 mAh g 1 at 5C and a discharge value of 39.8 mAh g 1 after 50 cycles. The capacity retention of 83% represents 23% of the theoretical value (charge and/or discharge process in twenty minutes), demonstrating the good performance of the battery. Thus, the developed C-LiFePO4 based inks allow to fabricate screen-printed cathodes suitable for printed lithium-ion batteries

Development of a novel aptamer-based multi-sensor device for the detection of osteopontin

Doctoral Dissertation for PhD degree in Chemical and Biological Engineering

Development of multifunctional coatings deposited on polymers based sensors for biomedical applications

Tese de Doutoramento (Programa Doutoral em Engenharia de Materiais)

Current approaches and future perspectives on strategies for the development of personalized tissue engineering therapies

Personalized tissue engineering and regenerative medicine (TERM) therapies propose patient-oriented effective solutions, considering individual needs. Cell-based therapies, for example, may benefit from cell sources that enable easier autologous set-ups or from recent developments on IPS cells technologies towards effective personalized therapeutics. Furthermore, the customization of scaffold materials to perfectly fit a patientâ s tissue defect through rapid prototyping technologies, also known as 3D printing, is now a reality. Nevertheless, the timing to expand cells or to obtain functional in vitrotissue substitutes prior to implantation prevents advancements towards routine use upon patient´s needs. Thus, personalized therapies also anticipate the importance of creating off-the-shelf solutions to enable immediately available tissue engineered products. This paper reviews the main recent developments and future challenges to enable personalized TERM approaches and to bring these technologies closer to clinical applications.

Influence of chitosan coating on protein-based nanohydrogels properties and in vitro gastric digestibility

Chitosan coating was applied in Lactoferrin (Lf)-Glycomacropeptide (GMP) nanohydrogels by layer-by-layer coating process. A volume ratio of 0.1 of Lf-GMP nanohydrogels (0.2 mg.mL-1, at pH 5.0) to chitosan (1 mg.mL-1, at pH 3) demonstrated to be the optimal condition to obtain stable nanohydrogels with size of 230 ± 12 nm, a PdI of 0.22 ± 0.02 and a -potential of 30.0 ± 0.15 mV. Transmission electron microscopy (TEM) images showed that the application of chitosan coating in Lf-GMP did not affect the spherical shape of nanohydrogels and confirmed the low aggregation of nanohydrogels in solution. The analysis of chemical interactions between chitosan and Lf-GMP nanohydrogels were performed by Fourier transform infrared spectroscopy (FTIR) and by circular dichroism (CD) that revealed that a specific chemical interaction occurring between functional groups of protein-based nanohydrogels and active groups of the chitosan was established. The effect of chitosan coating on release mechanisms of Lf-GMP nanohydrogels at acid conditions (pH 2, 37 ºC) was evaluated by the encapsulation of a model compound (caffeine) in these systems. Linear Superposition Model was used to fit the experimental data and revealed that Fick and relaxation mechanisms are involved in caffeine release. It was also observed that the Fick contribution increase with the application of chitosan coating. In vitro gastric digestion was performed with Lf-GMP nanohydrogels and Lf-GMP nanohydrogels with chitosan coating and it was observed that the presence of chitosan improve the stability of Lf and GMP (proteins were hydrolysed at a slower rate and were present in solution by longer time). Native electrophoreses revealed that the nanohydrogels without coating remained intact in solution until 15 min and with chitosan coating remained intact until 60 min, during gastric digestion.

In vivo imaging of glycol chitosan-based nanogel biodistribution

The preclinical development of nanomedicines raises several challenges and requires a comprehensive characterization. Among them is the evaluation of the biodistribution following systemic administration. In previous work, the biocompatibility and in vitro targeting ability of a glycol chitosan (GC) based nanogel have been validated. In the present study, its biodistribution in the mice is assessed, using near-infrared (NIR) fluorescence imaging as a tool to track the nanogel over time, after intravenous administration. Rapid whole body biodistribution of both Cy5.5 labeled GC nanogel and free polymer is found at early times. It remains widespreadly distributed in the body at least up to 6 h postinjection and its concentration then decreases drastically after 24 h. Nanogel blood circulation half-life lies around 2 h with the free linear GC polymer presenting lower blood clearance rate. After 24 h, the blood NIR fluorescence intensity associated with both samples decreases to insignificant values. NIR imaging of the organs shows that the nanogel had a body clearance time of 48 h, because at this time point a weak signal of NIR fluorescence is observed only in the kidneys. Hereupon it can be concluded that the engineered GC nanogel has a fairly long blood circulation time, suitable for biomedical applications, namely, drug delivery, simultaneously allowing efficient and quick body clearance.

Development of a poly(L-Lactic acid) based drug release system

Dissertação de mestrado em Biofísica e Bionanossistemas

Effect of different carbon materials as electron shuttles in the anaerobic biotransformation of nitroanilines

Aromatic amines resulted from azo dyes biotransformation under anaerobic conditions are generally recalcitrant to further anaerobic degradation. The catalytic effect of carbon materials (CM) on the reduction of azo dyes is known and has been confirmed in this work by increasing 3-fold the biological reduction rate of Mordant Yellow 1 (MY1). The resulting m-nitroaniline (m-NoA) was further degraded to m-phenylenediamine (m-Phe) only in the presence of CM. The use of CM to degraded anaerobically aromatic amines resulted from azo dye reduction was never reported before. In the sequence, we studied the effect of different CM on the bioreduction of o-, m- and p-NoA. Three microporous activated carbons with different surface chemistry, original (AC0), chemical oxidized with HNO3 (ACHNO3) and thermal treated (ACH2), and three mesoporous carbons, xerogels (CXA and CXB) and nanotubes (CNT) were assessed. In the absence of CM, NoA were only partially reduced to the corresponding Phe, whereas in the presence of CM, more than 90% was converted to the corresponding Phe. ACH2 and AC0 were the best electron shuttles, increasing the rates up to 8-fold. In 24h, the biological treatment of NoA and MY1 with AC0, decreased up to 88% the toxicity towards a methanogenic consortium, as compared to the non-treated solutions. This article is protected by copyright. All rights reserved

Vermiculite bio-barriers for Cu and Zn remediation: an eco-friendly approach for freshwater and sediments protection

The increase in heavy metal contamination in freshwater systems causes serious environmental problems in most industrialized countries, and the effort to find ecofriendly techniques for reducing water and sediment contamination is fundamental for environmental protection. Permeable barriers made of natural clays can be used as low-cost and eco-friendly materials for adsorbing heavy metals from water solution and thus reducing the sediment contamination. This study discusses the application of permeable barriers made of vermiculite clay for heavy metals remediation at the interface between water and sediments and investigates the possibility to increase their efficiency by loading the vermiculite surface with a microbial biofilm of Pseudomonas putida, which is well known to be a heavy metal accumulator. Some batch assays were performed to verify the uptake capacity of two systems and their adsorption kinetics, and the results indicated that the vermiculite bio-barrier system had a higher removal capacity than the vermiculite barrier (?34.4 and 22.8 % for Cu and Zn, respectively). Moreover, the presence of P. putida biofilm strongly contributed to fasten the kinetics of metals adsorption onto vermiculite sheets. In open-system conditions, the presence of a vermiculite barrier at the interface between water and sediment could reduce the sediment contamination up to 20 and 23 % for Cu and Zn, respectively, highlighting the efficiency of these eco-friendly materials for environmental applications. Nevertheless, the contribution of microbial biofilm in open-system setup should be optimized, and some important considerations about biofilm attachment in a continuous-flow system have been discussed.

Production of whey protein-based aggregates under ohmic heating

Formation of whey protein isolate protein aggregates under the influence of moderate electric fields upon ohmic heating (OH) has been monitored through evaluation of molecular protein unfolding, loss of its solubility, and aggregation. To shed more light on the microstructure of the protein aggregates produced by OH, samples were assayed by transmission electron microscopy (TEM). Results show that during early steps of an OH thermal treatment, aggregation of whey proteins can be reduced with a concomitant reduction of the heating chargeby reducing the come-up time (CUT) needed to reach a target temperatureand increase of the electric field applied (from 6 to 12 V cm1). Exposure of reactive free thiol groups involved in molecular unfolding of -lactoglobulin (-lg) can be reduced from 10 to 20 %, when a CUT of 10 s is combined with an electric field of 12 V cm1. Kinetic and multivariate analysis evidenced that the presence of an electric field during heating contributes to a change in the amplitude of aggregation, as well as in the shape of the produced aggregates. TEM discloses the appearance of small fibrillar aggregates upon the influence of OH, which have recognized potential in the functionalization of food protein networks. This study demonstrated that OH technology can be used to tailor denaturation and aggregation behavior of whey proteins due to the presence of a constant electric field together with the ability to provide a very fast heating, thus overcoming heat transfer limitations that naturally occur during conventional thermal treatments.

Mejoramiento del comportamiento térmico de sistemas de calentamiento de agua solares termosifónicos hechos con materiales no convencionales y con tanques de almacenamiento verticales y horizontales Performance improvement of solar thermosyphonic systems for water heating made of non conventional materials and using horizontal and vertical storage tanks

El objeto de estudio de este proyecto son los sistemas de calentamiento de agua mediante energía solar que funcionan termosifónicamente. En particular se tratará con dos diseños particulares generados por fabricantes de la Provincia de Córdoba y que han solicitado el asesoramiento del Grupo de Energía Solar (GES) para el mejoramiento de la performance térmica de dichos equipos. Se trata de dos sistemas que tienen materiales no tradicionales y se diferencian además por tener una distinta disposición del tanque de almacenamiento: uno es en forma vertical y el otro en forma horizontal. Basados en los resultados de un ensayo bajo norma internacional, donde se detectaron algunas puntos factibles de mejora, se propone en este proyecto el análisis en detalle de los equipos, para lo cual se les debe desarmar completos, para realizar un estudio analítico y experimental de los mismos con el objeto de hacer un planteo teórico-analítico del comportamiento de los mismos, con la implementación de propuestas de mejora y chequeo de los resultados. Se propone entonces como objetivo lograr un mejoramiento de la performance térmica de los citados equipos a partir de un estudio experimental y analítico. Asumiendo esta posibilidad de mejora, se plantea la hipótesis de que es posible representar el funcionamiento de estos equipos mediante modelos físico-matemáticos desarrollados a partir de ecuaciones y correlaciones conocidas y procesos a interpretar mediante resoluciones numéricas y softwares específicos de simulación. De esta manera, se plantea el despieze completo de los equipos para estudiar en detalle su estructura y conexiones internas y a partir de la geometría, dimensiones y propiedades termofísicas de materiales constructivos y fluidos de trabajo, realizar modelos físico-matemáticos que permitan realizar variaciones de propiedades y geometría y así buscar las mejores combinaciones que produzcan equipos más eficientes térmicamente. Los modelos físico-matemáticos serán codificados en lenguajes de alto nivel para poder luego de una validación de los modelos, correr simulaciones en un software de reconocimiento internacional que permite sumar dichos modelos mediante un protocolo de comunicación, haciendo que las poderosas prestaciones del software se puedan aplicar a nuestros modelos. Se complementará el estudio con un análisis exergético para identificar los puntos críticos en que se producen las pérdidas de oportunidad de aprovechar la energía disponible, para así analizar cómo solucionar los problemas en dichos puntos. Los materiales a utilizar serán los propios equipos provistos por los fabricantes, que serán modificados convenientemente para operarlos como prototipos Se espera obtener un conocimiento acabado de los procesos y principios de funcionamiento de los equipos, que permita plantear las mejoras, las cuales se implementarán en los prototipos, realizándose una medición mediante norma igual a la inicial para ver en que magnitud se logran las mejoras esperadas. Se pretende además que las mejoras a implementar, en la etapa de transferencia a las empresas involucradas, redunden no sólo en un beneficio técnico, sino que también los sea desde el punto de vista económico. Para ello se trabajará también sobre los procesos y métodos de fabricación para que los equipos mejorados no sean mas caros que los originales y de ser posible sean aún más económicos, todo esto apuntando a la difusión de la energía solar térmica y poner al alcance de todos estos equipos tan convenientes para la propagación de las energías limpias. El proyecto redundará también en un importante beneficio para el conocimiento de la comunidad científica en general, con el aporte de nuevos resultados en diseños novedosos y con nuevos materiales. Además, la institución se beneficiará con la formación que obtendrán los integrantes del proyecto, muchos de ellos en etapa de realización de sus estudios de posgrado y en una etapa importante de su vida como investigadores. The main goal of this project is the improvement of two thermosyphonic solar water heating systems, made of non conventional materials and with different arrangement of their storage tanks: one is vertical and the other one horizontal. The thermosyphonic systems are provided by manufacturers of the Córdoba Province, who came to the Solar Energy Group (GES) of the National University of Río Cuarto looking for help for the design of their products. In an agreement with these manufacturers, it was proposed this project in order to work analytically and experimentally in order to obtain physical-mathematical models of these two systems, which allow for changes to look by means of simulations the best changes to implement on the equipments for the improvement of their thermal performance. Then, the materials to be used are the proper systems provided by the manufacturers, which will be disarmed to be studied in detail. After the analytical study the proposals of improvement will be implemented in a high level language of programming to perform simulations in the environment of a well-known software for energy simulations (TRNSYS). After the simulations, the best modifications will be physically implemented in the prototypes to perform finally the same normalized test of the beginning and check the magnitude of the implemented improvements. The importance of this project is based on the offer of better systems the companies would make, which would benefit the deployment of the thermal solar energy. Another relevant point is to make the new equipments at the same cost of the previous ones or cheaper, in order to achieve a good deployment of the solar water heating systems; then, the manufacture processes and methods must be studied to obtain not only good technical solutions, but also economical equipments. In addition, this project will contribute to the increasing of the knowledge in the area of thermosyphonic solar systems and the training of postgraduate students.

Biological materials in colorectal surgery: current applications and potential for the future.

Biological materials are increasingly used in abdominal surgery for ventral, pelvic and perineal reconstructions, especially in contaminated fields. Future applications are multi-fold and include prevention and one-step closure of infected areas. This includes prevention of abdominal, parastomal and pelvic hernia, but could also include prevention of separation of multiple anastomoses, suture- or staple-lines. Further indications could be a containment of infected and/or inflammatory areas and protection of vital implants such as vascular grafts. Reinforcement patches of high-risk anastomoses or unresectable perforation sites are possibilities at least. Current applications are based mostly on case series and better data is urgently needed. Clinical benefits need to be assessed in prospective studies to provide reliable proof of efficacy with a sufficient follow-up. Only superior results compared with standard treatment will justify the higher costs of these materials. To date, the use of biological materials is not standard and applications should be limited to case-by-case decision.