Obtenção de nanopartículas de hexaferrita de bário pelo método pechini

In this study barium hexaferrite was (general formulae BaFe12O19) was synthesized by the Pechini method under different conditions of heat treatment. Precursors like barium carbonate and iron nitrate were used. These magnetic ceramic, with magnetoplumbite type structure, are widely used as permanent magnet because of its excellent magnetic properties, such as: high Curie temperature, good magnetic anisotropy, high coercivity and corrosion resistance. The samples were characterized by thermal analysis (DTA and TG), X- ray Diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Scanning Electron Microscopy (SEM) end Vibrating sample Magnetometer (VSM). The results confirm the expected phase, which was reinforced according to our analysis. A single phase powder at relatively high temperatures with particle sizes around 100 nm was obtained. The characteristic magnetic behavior one of the phases has been noted (probably superparamagnetic material), while another phase was identified as a ferrimagnetic material. The ferrimagnetic phase showed vortex configuration with two central and slightly inclined plateaus. In general, increase of heat treatment temperature and time, directly influenced the technological properties of the samples

Sinterização de Ce1-XEuXO2-(X/2) para aplicação como eletrólito sólido em células a combustível de temperaturas intermediárias

Given the environmental concern over global warming that occurs mainly by emission of CO2 from the combustion of petroleum, coal and natural gas research focused on alternative and clean energy generation has been intensified. Among these, the highlight the solid oxide fuel cell intermediate temperature (IT-SOFC). For application as electrolyte of the devices doped based CeO2 with rare earth ions (TR+ 3) have been quite promising because they have good ionic conductivity and operate at relatively low temperatures (500-800 ° C). In this work, studied the Ce1-xEuxO2-δ (x = 0,1, 0,2 and 0,3), solid solutions synthesized by the polymeric precursor method to be used as solid electrolyte. It was also studied the processing steps of these powders (milling, compaction and two step sintering) in order to obtain dense sintered pellets with reduced grain size and homogeneous microstructure. For this, the powders were characterized by thermal analysis, X-ray diffraction, particle size distribution and scanning electrons microscopy, since the sintered samples were characterized by dilatometry, scanning electrons microscopy, density and grain size measurements. By x-ray diffraction, it was verified the formation of the solid solution for all compositions. Crystallites in the nanometric scale were found for both sintering routes but the two step sintering presented significant reduction in the average grain size

Estudo e desenvolvimento de um capacitor eletrolítico de nióbio

It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential substitute, since both belong to the same group of the periodic table and because of this have many similar physical and chemical properties. Niobium has several technologically important applications, and Brazil has the largest reserves, around 96%. There are including niobium in reserves of tantalite and columbite in Rio Grande do Norte. These electrolytic capacitors have high capacitance specifies, ie they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium powder supplied by EEL-USP was first characterized by XRD, SEM, XRF and laser particle size, to then be sieved into three particle size, 200, 400 e 635mesh. The powders were then compacted and sintered at 1350, 1450 and 1550°C using two sintering time 30 and 60min. Sintering is one of the most important parts of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. The sintered samples then underwent a process of anodic oxidation, which created a thin film of niobium pentóxido over the whole porous surface of the sample, this film is the dielectric capacitor. The oxidation process variables influence the performance of the film and therefore the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor, ESR, relative density, porosity and surface area. After the characterizations was made an annealing in air ate 260ºC for 60min. After this treatment were made again the electrical measurements. The particle size of powders and sintering affected the porosity and in turn the specific area of the samples. The larger de area of the capacitor, greater is the capacitance. The powder showed the highest capacitance was with the smallest particle size. Higher temperatures and times of sintering caused samples with smaller surface area, but on the other hand the cleaning surface impurities was higher for this cases. So a balance must be made between the gain that is achieved with the cleaning of impurities and the loss with the decreased in specific area. The best results were obtained for the temperature of 1450ºC/60min. The influence of annealing on the loss factor and ESR did not follow a well-defined pattern, because their values increased in some cases and decreased in others. The most interesting results due to heat treatment were with respect to capacitance, which showed an increase for all samples after treatment

Construção, caracterização e aplicação de eletrodos para descarga por arco de cátodo oco

The system built to characterize electrodes and, consequently, deposited fine films are constituted by a hollow cathode that works to discharges and low pressures (approximately 10-3 to 5 mbar), a source DC (0 to 1200 V), a cylindrical camera of closed borossilicato for flanges of stainless steel with an association of vacuum bombs mechanical and spread. In the upper flange it is connected the system of hollow cathode, which possesses an entrance of gas and two entrances for its refrigeration, the same is electrically isolated of the rest of the equipment and it is polarized negatively. In front of the system of hollow cathode there is a movable sample in stainless steel with possibility of moving in the horizontal and vertical. In the vertical, the sample can vary its distance between 0 and 70 mm and, in the horizontal, can leave completely from the front of the hollow cathode. The sample and also the cathode hollow are equipped with cromel-alumel termopares with simultaneous reading of the temperatures during the time of treatment. In this work copper electrodes, bronze, titanium, iron, stainless steel, powder of titanium, powder of titanium and silício, glass and ceramic were used. The electrodes were investigated relating their geometry change and behavior of the plasma of the cavity of hollow cathode and channel of the gas. As the cavity of hollow cathode, the analyzed aspects were the diameter and depth. With the channel of the gas, we verified the diameter. In the two situations, we investigated parameters as flow of the gas, pressure, current and applied tension in the electrode, temperature, loss of mass of the electrode with relationship at the time of use. The flow of gas investigated in the electrodes it was fastened in a work strip from 15 to 6 sccm, the constant pressure of work was among 2.7 to 8 x 10-2 mbar. The applied current was among a strip of work from 0,8 to 0,4 A, and their respective tensions were in a strip from 400 to 220 V. Fixing the value of the current, it was possible to lift the curve of the behavior of the tension with the time of use. That curves esteem in that time of use of the electrode to its efficiency is maximum. The temperatures of the electrodes were in the dependence of that curves showing a maximum temperature when the tension was maximum, yet the measured temperatures in the samples showed to be sensitive the variation of the temperature in the electrodes. An accompaniment of the loss of mass of the electrode relating to its time of use showed that the electrodes that appeared the spherical cavities lost more mass in comparison with the electrodes in that didn't appear. That phenomenon is only seen for pressures of 10-2 mbar, in these conditions a plasma column is formed inside of the channel of the gas and in certain points it is concentrated in form of spheres. Those spherical cavities develop inside of the channel of the gas spreading during the whole extension of the channel of the gas. The used electrodes were cut after they could not be more used, however among those electrodes, films that were deposited in alternate times and the electrodes that were used to deposit films in same times, those films were deposited in the glass substrata, alumina, stainless steel 420, stainless steel 316, silício and steel M2. As the eletros used to deposit films in alternate time as the ones that they were used to deposit in same times, the behavior of the thickness of the film obeyed the curve of the tension with relationship the time of use of the electrode, that is, when the tension was maximum, the thickness of the film was also maximum and when the tension was minimum, the thickness was minimum and in the case where the value of the tension was constant, the thickness of the film tends to be constant. The fine films that were produced they had applications with nano stick, bio-compatibility, cellular growth, inhibition of bacterias, cut tool, metallic leagues, brasagem, pineapple fiber and ornamental. In those films it was investigated the thickness, the adherence and the uniformity characterized by sweeping electronic microscopy. Another technique developed to assist the production and characterization of the films produced in that work was the caloteste. It uses a sphere and abrasive to mark the sample with a cap impression, with that cap form it is possible to calculate the thickness of the film. Through the time of life of the cathode, it was possible to evaluate the rate of waste of its material for the different work conditions. Values of waste rate up to 3,2 x 10-6 g/s were verified. For a distance of the substratum of 11 mm, the deposited film was limited to a circular area of 22 mm diameter mm for high pressures and a circular area of 75 mm for pressure strip. The obtained films presented thickness around 2,1 µm, showing that the discharge of arch of hollow cathode in argon obeys a curve characteristic of the tension with the time of life of the eletrodo. The deposition rate obtained in this system it is of approximately 0,18 µm/min

Obtenção de filtro cerâmico a partir da diatomita e casca de arroz carbonizada visando tratamento de efluente têxtil

The effluents released by the textile industry have high concentrations of alkali, carbohydrates, proteins, in addition to colors containing heavy metals. Therefore, a filter was prepared aiming primarily to the removal of color. In order to prepare this filter, rice hulls and diatomite were used, which have in their structure, basically amorphous hydrated silica. The silica exists in three crystalline forms: quartz, tridymite and cristobalite. In accordance with the above considerations, this study was divided into two stages; the first corresponds to the preparation of the filter and the second to carry out the tests in the effluent/filter in order to verify the efficiency of the color removal. First, the raw material was subjected to a chemical analysis and XRD, and then the diatomite was mixed, via humid, with a planetarium windmill with 20 %, 40 %, 60 % and 80 % of rice husk ash. To the mixture, 5 % carboxymethylcellulose (CMC) was added as a binder at room temperature. The samples were uniaxially compacted into metallic matrix of 0.3 x 0.1 cm² of area at a pressure of 167 MPa by means of hydraulic press and then sintered at temperatures of 1,000 °C, 1,200 °C and 1,400 °C for 1 h and submitted to granulometry test using laser, linear retraction, water absorption, apparent porosity and resistance to bending, DTA, TMA and XRD. To examine the pore structure of the samples scanning electron microscope (SEM) was used. Also tests were carried out in a mercury porosimeter to verify the average size of the pores and real density of the samples. In the second stage, samples of the effluent were collected from a local industry, whose name will be preserved, located in Igapó, in the State of Rio Grande do Norte - RN. The effluent was first pretreated before filtration and then subjected to a treatment of flotation. The effluent was then characterized before and after filtration, with parameters of color, turbidity, suspended solids, pH, chemical and biochemical oxygen demand (COD and BOD). Thus, through the XRD analysis the formation of cristobalite α in all samples was observed. The best average size of pore was found to be 1.75 μm with 61.04 % apparent porosity, thus obtaining an average 97.9 % color removal and 99.8 % removal of suspended solid

Comportamento da adição do carbeto de nióbio (nBC) na matriz metálica do aço ferrítico 15kH2mfa

The 15Kh2MFA steel is a kind of Cr-Mo-V family steels and can be used in turbines for energy generation, pressure vessels, nuclear reactors or applications where the range of temperature that the material works is between 250 to 450°C. To improve the properties of these steels increasing the service temperature and the thermal stability is add a second particle phase. These particles can be oxides, carbides, nitrites or even solid solution of some chemical elements. On this way, this work aim to study the effect of addition of 3wt% of niobium carbide in the metallic matrix of 15Kh2MFA steel. Powder metallurgy was the route employed to produce this metallic matrix composite. Two different milling conditions were performed. Condition 1: milling of pure 15Kh2MFA steel and condition 2: milling of 15Kh2MFA steel with addition of niobium carbide. A high energy milling was carried out during 5 hours. Then, these two powders were sintered in a vacuum furnace (10-4torr) at 1150 and 1250°C during 60 minutes. After sintering the samples were normalized at 950°C per 3 minutes followed by air cooling to obtain a desired microstructure. Results show that the addition of niobium carbide helps to mill faster the particles during the milling when compared with that steel without carbide. At the sintering, the niobium carbide helps to sinter increasing the density of the samples reaching a maximum density of 7.86g/cm³, better than the melted steel as received that was 7,81g/cm³. In spite this good densification, after normalizing, the niobium carbide don t contributed to increase the microhardness. The best microhardness obtained to the steel with niobium carbide was 156HV and to pure 15Kh2MFA steel was 212HV. It happened due when the niobium carbide is added to the steel a pearlitic structure was formed, and the steel without niobium carbide submitted to the same conditions reached a bainitic structure

Desenvolvimento e caracterização de um compósito matriz metálica (CMM): aço EUROFER97 reforçado com Carbeto de Tântalo - TaC

Steel is an alloy EUROFER promising for use in nuclear reactors, or in applications where the material is subjected to temperatures up to 550 ° C due to their lower creep resistance under. One way to increase this property, so that the steel work at higher temperatures it is necessary to prevent sliding of its grain boundaries. Factors that influence this slip contours are the morphology of the grains, the angle and speed of the grain boundaries. This speed can be decreased in the presence of a dispersed phase in the material, provided it is fine and homogeneously distributed. In this context, this paper presents the development of a new material metal matrix composite (MMC) which has as starting materials as stainless steel EUROFER 97, and two different kinds of tantalum carbide - TaC, one with average crystallite sizes 13.78 nm synthesized in UFRN and another with 40.66 nm supplied by Aldrich. In order to improve the mechanical properties of metal matrix was added by powder metallurgy, nano-sized particles of the two types of TaC. This paper discusses the effect of dispersion of carbides in the microstructure of sintered parts. Pure steel powders with the addition of 3% TaC UFRN and 3% TaC commercial respectively, were ground in grinding times following: a) 5 hours in the planetary mill for all post b) 8 hours of grinding in the mill Planetary only for steel TaC powders of commercial and c) 24 hours in the conventional ball mill mixing the pure steel milled for 5 hours in the planetary mill with 3% TaC commercial. Each of the resulting particulate samples were cold compacted under a uniaxial pressure of 600MPa, on a cylindrical matrix of 5 mm diameter. Subsequently, the compressed were sintered in a vacuum furnace at temperatures of 1150 to 1250 ° C with an increment of 20 ° C and 10 ° C per minute and maintained at these isotherms for 30, 60 and 120 minutes and cooled to room temperature. The distribution, size and dispersion of steel and composite particles were determined by x-ray diffraction, scanning electron microscopy followed by chemical analysis (EDS). The structures of the sintered bodies were observed by optical microscopy and scanning electron accompanied by EDS beyond the x-ray diffraction. Initial studies sintering the obtained steel EUROFER 97 a positive reply in relation to improvement of the mechanical properties independent of the processing, because it is obtained with sintered microhardness values close to and even greater than 100% of the value obtained for the HV 333.2 pure steel as received in the form of a bar

Redução da morbi-mortalidade na síndrome de hellp completa com o uso de altas doses de dexametasona

Objective: To determine the clinical maternal and neonatal outcomes in HELLP syndrome patients treated with dexamethasone who either developed renal injury or renal insufficiency and to identify predictive values of urea and creatinine for the identification of subjects with HELLP syndrome at risk of developing renal insufficiency. Methods: Non-radomized intervention study of dexamethasone use in HELLP syndrome. A total of 62 patients were enrolled at Maternidade Escola Januário Cicco (MEJC). Patients received a total of 30 mg of dexamethasone IV, in three doses of 10 mg every 12 hours. A clinical and laboratory follow up were performed at 24, 48 and 72 hours. Patients were followed up to 6 months after delivery. Patients were grouped in accordance to renal function, i.e, normal and some type of renal lesion. Renal lesion was considered when creatinine was equal or greater than 1.3 mg/dl and diuresis less than 100 ml in 4 hours period and renal insufficiency was defined when dialysis was needed. Results: A total of 1230 patients with preeclampsia were admitted at MEJC. Of those 62 (5%) developed HELLP syndrome. There was no statistical difference in the groups with renal involvement or normal renal function with respect to the demographics, type of anesthesia used and delivery, and weight of the newborn. An improvement in the AST, ALT, LDH, haptoglobine, antithrombine, fibrinogenen and platelets was observed within 72 hours after dexamethosone use. There was a significant increase in the diuresis within the interval of 6 hours before the delivery and 24 hours after it. Of the 62 patients, 46 (74. 2%) had normal renal function and 16 (25.8%) evolved with renal lesion, with 5 (8.1%) needing dialysis. These 5 patients who received dialysis recovered the xi renal function. The delay in administering dexamethasone increased in 4.6% the risk of development of renal insufficiency. Patients with renal insufficiency had received significantly more blood products than subjects without renal lesion (p=0.03). Diuresis, leukocytes, uric acid, urea, creatinine were significantly different between the groups with normal renal function, renal lesion and renal insufficiency. The levels of creatinine 1.2mg/dl and uric acid 51mg/dl, at admission are predictive of subjects who will evolve with renal lesion (p<0.001). Maternal mortality was 3.2%. None of the subjects with renal insufficiency evolved with chronic renal disease. Conclusions: Dexamethasone in patients with HELLP syndrome seems to reduce significantly the hepatic microthrombosis and normalize hemostasis as seen by improvement of liver function. Renal injury can be considered, in HELLP syndrome, when creatinine levels are greater than 1.3 mg/dl and diuresis less than 100 ml/h in interval of 4 hours. The level of creatinine greater than 1.2 mg/dl and urea greater than 51mg/dl are predictive of subjects with HELLP syndrome who will develop renal injury. Patients who receive more red cell packs develop renal insufficiency. Finally, the delay in administering dexamethasone increases the risk of developing renal insufficiency

Alcoolemia em vítimas fatais de acidentes de trânsito no Rio Grande do Norte empregando cromatografia em fase gasosa - head space

Alcohol is one of the few psychotropic drugs that their consumption has admitted legally and sometimes encouraged by the society. Studies show alcohol as the highest consumption of drugs among young people and society in general, probably because of its availability and easy access. The abuse causes public health problems, which was closely related to the violence, socioeconomic problems and the high number of automobile accidents. Transit is one of the main sectors affected by the effects of alcohol, observing a high incidence in the studies. About half of automobile accidents occurs after the consumption of alcoholic beverage, and the vast majority of cases related to high concentrations of alcohol in the bloodstream. The relationship of drunk with traffic accidents is in fact evident everywhere in the world, including Brazil, where studies have shown a high relationship between alcohol consumption and traffic accidents. This study determined the alcohol in fatal victims of traffic accidents in the state of Rio Grande do Norte and established the profile of this population compared with those found in Brazil and other countries. Samples of blood of ethanol added to fulfillment of the standardization of chromatographic conditions and procedures for the analysis, being employed in the determination of alcohol in blood samples of 277 victims of traffic accidents, collected at the Institute of Scientific Technical Police of Rio Grande do North (ITEP) in the year 2007. The blood alcohol level was determined in these samples correlated with the sex, age and marital status of the victim and the location, day of week and month when the accident occurred, is doing a statistical analysis and outlining a profile of the victims of an accident at transit in the state of Rio Grande do Norte. The parameters of standardization studied ensured the quality of the analytical method and, consequently, to obtain reliable laboratory results. Being given the best temperature for injector (150 ºC), detector (250 ºC) and column (50 ºC) with a flow of gas in the column of 2mL/minutos and analysis of time of 12 minutes. The method was linear in the range of 0.01 to 3.2 g / L (r2 = 0.9989) with average recovery of 100.2% and precision with coefficient of variation less than 15%. The analysis carried out on victims of fatal road traffic accidents, ethanol detected in the blood in 66.43% of the victims and these, 96% showed concentration ≥ 0.2 g / L, 87.73% of victims were male, while 12.27% female. The younger age group (1535 years) was the most involved (52,35%) and most single (55.60%). The accidents occurred with greater prevalence in the day on Monday (27%) followed by Sunday (24,19%) and Saturday (15,52%) and it was found that the prevalence of injuries varied between the different months of the year, and in February (14.4%) and April (10.47%) the months that had a higher number of accidents, however this oscillation showed no statistically significant difference. Also no significant difference was observed between the tracks of concentration found in men and women. The standardized method showed to be efficient, given satisfactorily to the goals of this work, and the high levels of alcohol found in victims of fatal road traffic accidents are consistent with several studies of literature, and the profile of the victim also supported by presenting in its most young adults, male and single

Qualidade de frutos de cajá-manga armazenados sob diferentes temperaturas

O presente trabalho teve como objetivo determinar o efeito de diferentes temperaturas de armazenamento na qualidade de frutos de cajá-manga. Os frutos de cajá-manga foram obtidos junto ao CEAGESP - Companhia de Entrepostos e Armazéns Gerais de São Paulo, e transportados em caixas isotérmicas para o Laboratório onde foram selecionados quanto à aparência, estádio de maturação, ausência de danos físicos, depois sanitizados em solução de 50 ppm de cloro livre e acondicionados em bandejas de poliestireno expandido, envolto por filme de policloreto de vinila (PVC). O delineamento experimental utilizado foi o inteiramente casualizado, com três tratamentos (4ºC, 8ºC e 25ºC) e 5 épocas de avaliação (0; 3; 6; 9 e 12 dias após a instalação do experimento). em cada coleta, foram avaliadas a firmeza, a acidez titulável, os sólidos solúveis, o teor de ácido ascórbico, a cor da casca e, também, a liberação de CO2 pelos frutos ao longo do tempo. Foi observado que baixas temperaturas prolongam a vida útil dos frutos e que a temperatura de armazenamento influencia nas características avaliadas, sendo a temperatura de 8ºC a mais adequada para o armazenamento dos frutos de cajá-manga.

Predação de Diaspididae por larvas de Coccidophilus citricola em diferentes temperaturas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeitos da restrição alimentar protéica ou energética sobre o crescimento de frangos de corte criados em diferentes temperaturas ambiente

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeitos de substratos e temperaturas na germinação de sementes de tamareira-anã (Phoenix roebelenii O'Brien)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento de Oligonychus ilicis em Coffea canephora sob diferentes temperaturas

Oligonychus ilicis (McGregor) (Acari) (Tetranychidae) é uma das principais pragas de Coffea canephora Pierre & Froehner. Neste trabalho, avaliou-se o efeito de diferentes temperaturas no desenvolvimento desse ácaro-vermelho em folhas de C. canephora, em laboratório. Confinaram-se 80 fêmeas em 40 arenas, constituídas de disco foliar de 4 cm, para oviposição nas temperaturas de 21, 24, 27, 30 e 33 ºC. Foram selecionados ao acaso pelo menos dois ovos para avaliar o desenvolvimento embrionário. Após a eclosão da larva, foram realizadas avaliações a cada 12 horas para obtenção da duração e sobrevivência larval. Para avaliar a longevidade foi transferido um ácaro macho da criação para as arenas com uma fêmea para acasalamento. O limite térmico de desenvolvimento inferior e a constante térmica foram determinados para a duração do desenvolvimento de ovo a adulto. O tempo de desenvolvimento das fases imaturas diminuiu com o aumento da temperatura. As fases de ovo, larva, protocrisálida, protoninfa, deutocrisálida, deutoninfa e teleiocrisálida variaram, respectivamente, de 10,4 a 4,3; 2,4 a 1,2; 2,0 a 1,0; 2,3 a 1,2; 1,9 a 1,0; 3,0 a 1,5 e 2,3 a 1,0 dias. O aumento da temperatura afetou o período de desenvolvimento, reduzindo a duração de ovo-adulto e a longevidade. O limite térmico inferior foi de 9,0 ºC para o período de ovo-adulto e constante térmica de 256,4 graus-dias. em condições de laboratório, a faixa de temperatura que favorece o desenvolvimento do ácaro em C. canephora foi de 24 a 30 ºC. O limite térmico inferior não é limitante para ocorrência de O. ilicis em áreas cultivadas com C. canephora no estado do Espírito Santo.

Efeito de temperaturas de armazenamento e de genótipos de feijoeiro sobre a resistência a Acanthoscelides obtectus (Say) (Coleoptera: Bruchidae)

Visando avaliar os efeitos de diferentes temperaturas de armazenamento e de genótipos de feijoeiro, Phaseolus vulgaris L., sobre a expressão da resistência ao caruncho, Acanthoscelides obtectus (Say), realizaram-se ensaios com os genótipos Arc.1S, Arc.1, Arc.2, Arc.4 e Carioca Pitoco. Os grãos de Arc.1S e Arc.2 expressaram resistência a A. obtectus nas temperaturas de 20ºC, 25ºC e 30°C; a resistência do genótipo Arc.1 diminuiu à medida que a temperatura de armazenamento foi elevada de 25ºC para 30ºC. A interação genótipos x temperaturas foi significativa, indicando que a elevação da temperatura afeta a expressão da resistência. A temperatura de 20ºC foi a mais adequada para discriminar os genótipos de feijoeiro, quanto a resistência.