The behaviour of laminar stratified methane/air flames in counterflow

Flames propagating through a mixture with a gradient of equivalence ratio have been previously demonstrated to travel faster or slower than their equivalent premixed flames. The present study aims to numerically investigate the response of strained laminar methane-air flames to such gradients. The flames are simulated in a counterflow configuration where a premixed reactant stream at equivalence ratio φR opposes a hot equilibrium stream at equivalence ratio φP. Premixed and stratified flames are compared with respect to the equivalence ratio φ* and the corresponding gradient ∇φ* at the point of peak heat release rate, for three strain rates, a=50, 300 and 500s-1 and a range of φ*. The effect of different stratification levels is also investigated by varying the ratio of φP to φR, Θ. Results indicate that, as long as flames stabilize within the diffusion layer and Θ>1, increased heat release rate Q is seen throughout the progress variable space in comparison to the premixed state. In contrast, an attenuation of heat release rate is seen for Θ<1. The enhancement (or attenuation) of heat release varies monotonically with Θ. The effect of stratification on flame behavior becomes more pronounced as the strain rate increases. The present study reveals the mechanisms for the propagation of quasi-steady stratified flames under lean and rich conditions: stratified flames are primarily dominated by the diffusion of heat under lean conditions, and diffusion of H2 under rich conditions. Thanks to species and thermal support, stratified flames continue to burn beyond the premixed lean and rich flammability limits. Further investigation on the unsteady response of flames to the fluctuating equivalence ratio implies that the steady results represent the unsteady response well, as long as φ* and ∇φ* are similar in both steady and unsteady cases. © 2013 The Combustion Institute.

Experimental investigation of dynamic response of acoustically forced turbulent premixed CH4/CO2/air flames

Increasing demand for energy and continuing increase in environmental as well as financial cost of use of fossil fuels drive the need for utilization of fuels from sustainable sources for power generation. Development of fuel-flexible combustion systems is vital in enabling the use of sustainable fuels. It is also important that these sustainable combustion systems meet the strict governmental emission legislations. Biogas is considered as one of the viable sustainable fuels that can be used to power modern gas turbines: However, the change in chemical, thermal and transport properties as well as change in Wobbe index due to the variation of the fuel constituents can have a significant effect on the performance of the combustor. It is known that the fuel properties have strong influence on the dynamic flame response; however there is a lack of detailed information regarding the effect of fuel compositions on the sensitivity of the flames subjected to flow perturbations. In this study, we describe an experimental effort investigating the response of premixed biogas-air turbulent flames with varying proportions of CH4 and CO2 to velocity perturbations. The flame was stabilized using a centrally placed conical bluff body. Acoustic perturbations were imposed to the flow using loud speakers. The flame dynamics and the local heat release rate of these acoustically excited biogas flames were studied using simultaneous measurements of OH and H2CO planar laser induced fluorescence. OH* chemiluminescence along with acoustic pressure measurements were also recorded to estimate the total flame heat release modulation and the velocity fluctuations. The measurements were carried out by keeping the theoretical laminar flame speed constant while varying the bulk velocity and the fuel composition. The results indicate that the flame sensitivity to perturbations increased with increased dilution of CH4 by CO2 at low amplitude forcing, while at high amplitude forcing conditions the magnitude of the flame response was independent of dilution.

Analysis of fields in an air-cored superconducting synchronous motor with an HTS racetrack field winding

High temperature superconducting (HTS) synchronous motors can offer significant weight and size reductions, as well as improved efficiency, over conventional copper-wound machines due to the higher current density of high temperature superconducting (HTS) materials. In order to optimise the design parameters and performance of such a machine, this paper proposes a basic physical model of an air-cored HTS synchronous motor with a copper armature winding and HTS field winding. An analytical method for the field analysis in the synchronous motor is then presented, followed by a numerical finite element analysis (FEA) model to verify the analytical solution. The model is utilised to study the influence of the geometry of the HTS coils on the magnetic field at the armature winding, and geometrical parameter optimisation is carried out using this theoretical model to obtain a more sinusoidal magnetic field at the armature, which has a major influence on the performance of the motor.

A simple diesel engine air-path model to predict the cylinder charge during transients: Strategies for reducing transient emissions spikes

Simple air-path models for modern (VGT/EGR equipped) diesel engines are in common use, and have been reported in the literature. This paper addresses some of the shortcomings of control-oriented models to allow better prediction of the cylinder charge properties. A fast response CO2 analyzer is used to validate the model by comparing the recorded and predicted CO2 concentrations in both the intake port and exhaust manifold of one of the cylinders. Data showing the recorded NOx emissions and exhaust gas opacity during a step change in engine load illustrate the spikes in both NOx and smoke seen during transient conditions. The predicted cylinder charge properties from the model are examined and compared with the measured NOx and opacity. Together, the emissions data and charge properties paint a consistent picture of the phenomena occurring during the transient. Alternative strategies for the fueling and cylinder charge during these load transients are investigated and discussed. Experimental results are presented showing that spikes in both NOx and smoke can be avoided at the expense of some loss in torque response. Even if the torque response must be maintained, it is demonstrated that it is still possible to eliminate spikes in NOx emissions for the transient situation being examined. Copyright © 2006 SAE International.