The construction of sexpartite vaults in Europe

Sexpartite vaults constitute one of the most interesting chapters in European Gothic architecture. Originally, the use of the square cross-ribbed vault was limited to relatively small spaces, but when the need arose to cover spaces of considerable size, a new vault with very peculiar characteristics appeared. This new vault was a cross-ribbed vault that was reinforced in the centre by a rib that was parallel to the transverse ribs which effectively divided the vault in half. This configuration breaks the side arch into two fragments, creating a pair of windows on each side. The volumetrics of these vaults is extremely complex and the difficulties involved in their construction perhaps explain why they were abandoned in favour of the simple cross ribbed vault, now with rectangular sections. The existence of the sexpartite vault barely lasted more than fifty years, from the end of the XII century and the beginning of the XIII. Towards the end of the 19th century Viollet-le-Duc gave a succinct explanation of this type of vault. A. Choisy also, later, devotes some pages to the French sexpartite vault; since then, the subject has only been broached in a few references in later studies on Gothic architecture. However, despite its short period of existence, the sexpartite vault spread throughout Europe and was used to build important vaulting. Viollet-le-Duc's sexpartite vault could be considered to be the prototype of them all, while it is true that the studies that we have conducted so far lead us to affirm that there is a wide variety of vaults, with different volumetric spaces and different construction strategies. Therefore, we believe that this chapter of international Gothic deserves further study applying the knowledge and resources that are available today. This paper has been written to explore the most significant European sexpartite vaults. New measurement technology has led to a revolution in research into the history of construction, allowing studies to be conducted that were hitherto impossible. Thorough data collection using total station and photogrammetry has enabled us to identify the stereotomy of the voussoirs, tas-de-charges and keystones, as well as the bonding of the surfaces of the severies. A comparison of the construction techniques employed in the different vaults studied reveals common construction features and aspects that are specific to each country. Thus we are able to establish the relationship between sexpartite vaults in different European countries and their influence on each other.

Electro y dielectroforesis de nanopartículas por efecto fotovoltaico

El objetivo de esta tesis doctoral es la investigación del nuevo concepto de pinzas fotovoltaicas, es decir, del atrapamiento, ordenación y manipulación de partículas en las estructuras generadas en la superficie de materiales ferroeléctricos mediante campos fotovoltaicos o sus gradientes. Las pinzas fotovoltaicas son una herramienta prometedora para atrapar y mover las partículas en la superficie de un material fotovoltaico de una manera controlada. Para aprovechar esta nueva técnica es necesario conocer con precisión el campo eléctrico creado por una iluminación específica en la superficie del cristal y por encima de ella. Este objetivo se ha dividido en una serie de etapas que se describen a continuación. La primera etapa consistió en la modelización del campo fotovoltaico generado por iluminación no homogénea en substratos y guías de onda de acuerdo al modelo de un centro. En la segunda etapa se estudiaron los campos y fuerzas electroforéticas y dielectroforéticas que aparecen sobre la superficie de substratos iluminados inhomogéneamente. En la tercera etapa se estudiaron sus efectos sobre micropartículas y nanopartículas, en particular se estudió el atrapamiento superficial determinando las condiciones que permiten el aprovechamiento como pinzas fotovoltaicas. En la cuarta y última etapa se estudiaron las configuraciones más eficientes en cuanto a resolución espacial. Se trabajó con distintos patrones de iluminación inhomogénea, proponiéndose patrones de iluminación al equipo experimental. Para alcanzar estos objetivos se han desarrollado herramientas de cálculo con las cuales obtenemos temporalmente todas las magnitudes que intervienen en el problema. Con estas herramientas podemos abstraernos de los complicados mecanismos de atrapamiento y a partir de un patrón de luz obtener el atrapamiento. Todo el trabajo realizado se ha llevado a cabo en dos configuraciones del cristal, en corte X ( superficie de atrapamiento paralela al eje óptico) y corte Z ( superficie de atrapamiento perpendicular al eje óptico). Se ha profundizado en la interpretación de las diferencias en los resultados según la configuración del cristal. Todas las simulaciones y experimentos se han realizado utilizando como soporte un mismo material, el niobato de litio, LiNbO3, con el f n de facilitar la comparación de los resultados. Este hecho no ha supuesto una limitación en los resultados pues los modelos no se limitan a este material. Con respecto a la estructura del trabajo, este se divide en tres partes diferenciadas que son: la introducción (I), la modelización del atrapamiento electroforético y dielectroforético (II) y las simulaciones numéricas y comparación con experimentos (III). En la primera parte se fijan las bases sobre las que se sustentarán el resto de las partes. Se describen los efectos electromagnéticos y ópticos a los que se hará referencia en el resto de los capítulos, ya sea por ser necesarios para describir los experimentos o, en otros casos, para dejar constancia de la no aparición de estos efectos para el caso en que nos ocupa y justificar la simplificación que en muchos casos se hace del problema. En esta parte, se describe principalmente el atrapamiento electroforético y dielectroforético, el efecto fotovoltaico y las propiedades del niobato de litio por ser el material que utilizaremos en experimentos y simulaciones. Así mismo, como no debe faltar en ninguna investigación, se ha analizado el state of the art, revisando lo que otros científicos del campo en el que estamos trabajando han realizado y escrito con el fin de que nos sirva de cimiento a la investigación. Con el capítulo 3 finalizamos esta primera parte describiendo las técnicas experimentales que hoy en día se están utilizando en los laboratorios para realizar el atrapamiento de partículas mediante el efecto fotovoltaico, ya que obtendremos ligeras diferencias en los resultados según la técnica de atrapamiento que se utilice. En la parte I I , dedicada a la modelización del atrapamiento, empezaremos con el capítulo 4 donde modelizaremos el campo eléctrico interno de la muestra, para a continuación modelizar el campo eléctrico, los potenciales y las fuerzas externas a la muestra. En capítulo 5 presentaremos un modelo sencillo para comprender el problema que nos aborda, al que llamamos Modelo Estacionario de Separación de Carga. Este modelo da muy buenos resultados a pesar de su sencillez. Pasamos al capítulo 6 donde discretizaremos las ecuaciones que intervienen en la física interna de la muestra mediante el método de las diferencias finitas, desarrollando el Modelo de Distribución de Carga Espacial. Para terminar esta parte, en el capítulo 8 abordamos la programación de las modelizaciones presentadas en los anteriores capítulos con el fn de dotarnos de herramientas para realizar las simulaciones de una manera rápida. En la última parte, III, presentaremos los resultados de las simulaciones numéricas realizadas con las herramientas desarrolladas y comparemos sus resultados con los experimentales. Fácilmente podremos comparar los resultados en las dos configuraciones del cristal, en corte X y corte Z. Finalizaremos con un último capítulo dedicado a las conclusiones, donde resumiremos los resultados que se han ido obteniendo en cada apartado desarrollado y daremos una visión conjunta de la investigación realizada. ABSTRACT The aim of this thesis is the research of the new concept of photovoltaic or optoelectronic tweezers, i.e., trapping, management and manipulation of particles in structures generated by photovoltaic felds or gradients on the surface of ferroelectric materials. Photovoltaic tweezers are a promising tool to trap and move the particles on the surface of a photovoltaic material in a monitored way. To take advantage of this new technique is necessary to know accurately the electric field created by a specifc illumination in the crystal surface and above it. For this purpose, the work was divided into the stages described below. The first stage consisted of modeling the photovoltaic field generated by inhomogeneous illumination in substrates and waveguides according to the one-center model. In the second stage, electrophoretic and dielectrophoretic fields and forces appearing on the surface of substrates and waveguides illuminated inhomogeneously were studied. In the third stage, the study of its effects on microparticles and nanoparticles took place. In particular, the trapping surface was studied identifying the conditions that allow its use as photovoltaic tweezers. In the fourth and fnal stage the most efficient configurations in terms of spatial resolution were studied. Different patterns of inhomogeneous illumination were tested, proposing lightning patterns to the laboratory team. To achieve these objectives calculation tools were developed to get all magnitudes temporarily involved in the problem . With these tools, the complex mechanisms of trapping can be simplified, obtaining the trapping pattern from a light pattern. All research was carried out in two configurations of crystal; in X section (trapping surface parallel to the optical axis) and Z section (trapping surface perpendicular to the optical axis). The differences in the results depending on the configuration of the crystal were deeply studied. All simulations and experiments were made using the same material as support, lithium niobate, LiNbO3, to facilitate the comparison of results. This fact does not mean a limitation in the results since the models are not limited to this material. Regarding the structure of this work, it is divided into three clearly differentiated sections, namely: Introduction (I), Electrophoretic and Dielectrophoretic Capture Modeling (II) and Numerical Simulations and Comparison Experiments (III). The frst section sets the foundations on which the rest of the sections will be based on. Electromagnetic and optical effects that will be referred in the remaining chapters are described, either as being necessary to explain experiments or, in other cases, to note the non-appearance of these effects for the present case and justify the simplification of the problem that is made in many cases. This section mainly describes the electrophoretic and dielectrophoretic trapping, the photovoltaic effect and the properties of lithium niobate as the material to use in experiments and simulations. Likewise, as required in this kind of researches, the state of the art have been analyzed, reviewing what other scientists working in this field have made and written so that serve as a foundation for research. With chapter 3 the first section finalizes describing the experimental techniques that are currently being used in laboratories for trapping particles by the photovoltaic effect, because according to the trapping technique in use we will get slightly different results. The section I I , which is dedicated to the trapping modeling, begins with Chapter 4 where the internal electric field of the sample is modeled, to continue modeling the electric field, potential and forces that are external to the sample. Chapter 5 presents a simple model to understand the problem addressed by us, which is called Steady-State Charge Separation Model. This model gives very good results despite its simplicity. In chapter 6 the equations involved in the internal physics of the sample are discretized by the finite difference method, which is developed in the Spatial Charge Distribution Model. To end this section, chapter 8 is dedicated to program the models presented in the previous chapters in order to provide us with tools to perform simulations in a fast way. In the last section, III, the results of numerical simulations with the developed tools are presented and compared with the experimental results. We can easily compare outcomes in the two configurations of the crystal, in section X and section Z. The final chapter collects the conclusions, summarizing the results that were obtained in previous sections and giving an overview of the research.

Influence of castration on growth performance and carcass and meat quality of heavy female pigs

The main objetive of this Doctoral Thesis was to study the influence of female castration and pig sex on growth performance and carcass and meat quality of white pigs slaughtered at different final weights. Three experiments (Exp.) were conducted. In Exp. 1, a total of 200 (Landrace * Large White dam x Pietrain * Large White sire) gilts of 50 ± 3 days of age (23.3 ± 1.47 kg BW) was used to investigate the effects of castration (intact females, IF vs. castrated feamles, CF) and slaughter weight (106 vs. 122 kg BW) on productive performance and carcass and meat quality. There were four experimental treatments arranged as a 2 x 2 factorial and 5 replicates of 10 pigs each per treatment. Half of the gilts were ovariectomized at 58 d of age (8 days after the beginning of the trial; 29.8 ± 1.64 kg BW) whereas the other half remained intact. Meat samples were taken at m. Longissimus thoracis at the level of the last rib and subcutaneous fat samples were taken at the tail insertion. For the entire experiment period, CF had higher BW gain (P<0.05) and backfat and m. Gluteus medius (GM) fat thickness (P<0.001) than IF. However, IF had higher loin and trimmed primal cut yields (P<0.05) than CF. Meat quality was similar for IF and CF but the proportion of linoleic acid in subcutaneous fat was higher (P<0.001) for IF. Pigs slaughtered at 122 kg BW had higher (P<0.001) feed intake and poorer feed efficiency than pigs slaughtered at 106 kg BW. An increase in slaughter weight (SW) improved (P<0.001) carcass yield but decreased (P<0.05) trimmed primal cut yield. Meat from females slaughtered at the heavier BW was redder (a*; P<0.001) and had more (P<0.01) intramuscular fat and less thawing (P<0.05) and cooking (P<0.10) loss than meat from females slaughtered at the lighter BW. Also, females slaughtered at 122 kg BW had less (P<0.01) linoleic acid content in the subcutaneous fat than pigs slaughtered at 106 kg BW. Castration of gilts and slaughtering at heavier BW might be useful practices for the production of heavy pigs destined to the dry cured industry in which a certain amount of fat in the carcass is required. In contrast, when the carcasses are destined to fresh meat production, IF slaughtered at 106 kg BW are a more efficient alternative. In Exp. 2, crossbred pigs (n=240) from Pietrain*Large White sires mated to Landrace*Large White dams with an average of 100 d of age (60.5 ± 2.3 kg) were used to investigate the effects of gender and slaughter weight (SW) on growth performance and carcass and meat quality characteristics. There were 6 treatments arranged factorially with 3 genders (IF vs. CF vs.castrated males, CM) and 2 SW (114 vs. 122 kg BW). Each of the 6 combinations of treatments was replicated 4 times and the experimental unit was a pen with 10 pigs. Castrated males and CF ate more feed, grew faster and had more carcass backfat depth and fat thickness at the GM muscle, but lower loin yield than IF (P<0.05). In addition, CF and CM had more intramuscular fat (P<0.05) and less linoleic acid content in the subcutaneous fat (P<0.01) than IF. Pigs slaughtered at 122 kg BW had lower ADG (P<0.05), poor gain-to-feed ratio (P<0.05), and more GM fat than pigs slaughtered at 114 kg BW (P < 0.05). It is concluded that CF and CM had similar productive performance and meat quality characteristics when slaughtered at the same age, and that the castration of females improved daily gains and increased weight and fat content of primal cuts with respect to IF. Therefore, castration of females is recommended in pigs destined to the dry-cured industry because of the beneficial effects on the quality of the primal cuts. In Exp. 3, the effects of gender and castration of females (IF vs. CF vs. CM) on performance and carcass and meat quality were studied in crossbred pigs (Landrace x Large White dams x Duroc sires) slaughtered at 119.2 (trial 1) or 131.6 (trial 2) kg BW. Intact females had better feed conversion and less carcass fat than CF and CM. Trimmed shoulder yield was higher for CM than for CF with IF being intermediate. Primal cut yield and meat quality, however were similar for all treatments. Proportion of linoleic acid in backfat was lower for CF than for IF or CM, and the differences were significant in pigs slaughtered witn 131.6 kg BW. The higher fat content and the fatty acid profile favour the use of CF and CM over IF for the production of heavy pigs destined to the dry-cured industry.

Aspectos formales y constructivos en la obra de Guillem Sagrera: el uso de las plantillas

Los enjarjes, jarjas o jarjamentos conforman el comienzo de la bóveda de crucería, el lugar en el que todos los nervios nacen reunidos. Permiten la transición entre el muro y las dovelas que constituyen nervios, resolviendo un encuentro de gran importancia constructiva. Están compuestos por piezas de lechos horizontales que traban con el muro y que, además de conformar el arranque de los nervios, han de proporcionar apoyo a las primeras dovelas. Al construirse a la vez que el muro y antes que el resto de la bóveda, se podría decir que son los encargados de portar su ADN: en ellos queda registrado el número de nervios que tendrá la bóveda, su curvatura, desde qué altura arrancará cada uno, su perfil, etc. El objetivo de este trabajo se centra en estudio de los enjarjes en la obra de Guillem Sagrera abordando su dimensión tecnológica, constructiva y de diseño. Dos características los distinguen de otras soluciones y justifican su interés: los nervios surgen directamente del muro, sin la intermediación de capiteles, ménsulas o pilastras; y se diseñan con la intención de facilitar la aparición de intersecciones entre las molduras de sus perfiles, en algunos casos mediante el cruce de los ejes de los nervios. Sagrera nos acerca a una innovación arquitectónica en la que el esfuerzo no se centra en realizar bóvedas con muchos nervios o con trazados en planta complejos, sino en la cuidada resolución de este encuentro de nervios. En ella se adivina el trabajo minucioso con las plantillas que controlan el trazado del contorno de los lechos de las piezas y la hábil mano de los canteros que son capaces de tallar intersecciones de gran complejidad. Se ha realizado un repaso de los primeros experimentos relativos al modo de relacionarse los nervios entre sí para ilustrar el contexto y origen de las soluciones realizadas por Guillem Sagrera. Mostramos que ante ciertas dificultades, consecuencia de la reunión de nervios, los constructores fueron capaces de desarrollar nuevas soluciones, mediante la experimentación con un sistema constructivo que conocían y manejaban con destreza. Para acercarnos a la comprensión de las estrategias de diseño que permiten el proyecto de estos enjarjes y los procedimientos técnicos y constructivos necesarios para su ejecución, nos vimos en la necesidad de adentrarnos en la problemática general de los enjarjes de la bóveda de crucería. De este modo, lo que empezó siendo una introducción para poder contextualizar la obra del mallorquín acabó convirtiéndose en la primera parte de la tesis, cuyo volumen prácticamente equipara a la segunda. En ella presentamos el proceso de diseño, trazado y talla de los cuatro enjarjes llevados a cabo en el taller de cantería de la ETSAM, en los que hemos podido experimentar de manera práctica los aspectos teóricos desarrollados. Estos ensayos nos han permitido contrastar hipótesis y baremar la dificultad de ciertos procedimientos o procesos, así como acercarnos realmente al elemento constructivo. El trabajo práctico nos ha enseñado a no fiarnos siempre de las hipótesis que se desarrollan modelando con el ordenador o dibujando; a valorar el pensar con las manos. En relación con la obra de Sagrera, la presente investigación realiza aportaciones al conocimiento del cambio proyectual y constructivo llevado a cabo en los arranques de las bóvedas entre los siglos XIII y XV, cuando los nervios comienzan a surgir directamente de los soportes y se dan los primeros cruzamientos. Mostramos que ya no solamente se construyen enjarjes fruto directo de la geometría general de la bóveda, sino que se llevan a cabo cambios deliberados en relación a su resultado, en los que se advierten decisiones proyectuales que, por supuesto, no serían viables sin las posibilidades que ofrece el trabajo con plantillas. ABSTRACT The solid blocks commonly known as tas-de-charge (in Spanish enjarjes, jarjas or jarjamentos) constitute the beginning of the ribbed vault – the place from which all the ribs spring together. They facilitate a transition between the wall and the rib voussoirs, and thus solve a junction of utmost constructive importance. They consist of blocks set in horizontal courses which interlock with the wall and which, as well as constituting the springing of the ribs, serve as a support for their first voussoirs. The tas-de-charge are built simultaneously with the wall and well before the remainder of the vault – thus, they arguably carry its ‘DNA’, since they register how many ribs the vault will have as well as their curvature, their springing height or their profile. This work is focused on the study of the tas-de-charge in the works of Guillem Sagrera, and will address their technological, constructive and design aspects. Two characteristics set these apart from other solutions and justify their relevance: these are that the ribs spring directly from the wall without the mediation of capitals, corbels or pilasters; and that they are deliberately designed to force the intersection of their mouldings, in some cases by crossing the rib axes. Sagrera’s work tells a story of architectural innovation – one where the effort is not centred on creating vaults with numerous ribs or a sophisticated ground plan, but on carefully solving the rib unions, which evidence a meticulous use of templates to control the tracing of the pieces’ profiles as well as the skill of the stonemasons, able to carve highly complex intersections. An overview of the first experiments with rib relationships will illustrate the context and origin of Guillem Sagrera’s solutions. We show how, faced with difficulties arising from the convergence of ribs into the tas-de-charge, builders were able to develop new solutions by experimenting with a construction system that they were already familiar with and could control easily. In order to gain a better insight into the design strategies behind his tas-de-charge and the technical and constructive procedures required for their execution, we found ourselves facing the need to address the general subject of tas-de-charge in ribbed vaults. This, which began as an introduction meant as context for Sagrera’s work, took on a life of its own and became the first half of the thesis, with a volume practically equal to that of the second. We have devoted a chapter to experimental archaeology. It comprises the design, tracing and carving processes for the four tas-de-charge executed at the ETSAM Stonecutting Workshop, in which we have tested experimentally the theories studied in the previous chapters. These tests have allowed us to contrast hypotheses, assess the difficulty of certain procedures or processes and understand the built element as a real entity. The practical work has taught us not to always trust the hypotheses proposed through computer modelling or drawing – and to recognise the importance of coordinating the hands and the mind. After studying Sagrera’s work and contrasting it with other related or previous tas-de-charge, our research will seek to make a contribution to the study of the shift in the design and construction of vault springers that took place between the 13th and 14th centuries, when ribs began to spring directly from their support and moulding crossings began to appear. We show that, from then on, tas-de-charge would not only depend on the general vault geometry – deliberate modifications would be carried out in order to achieve the desired result. This reveals design decisions that would have been unworkable if not for the effective use of template strategies.

Nuevo concepto de elementos estructurales horizontales de vidrio : placa autoportante y pretensada en forma de pi

En los últimos años, podemos darnos cuenta de la importancia que tienen las nuevas aplicaciones de vidrio especialmente en edificios turísticos donde el vértigo juega un papel importante en la visita. Sin embargo los sistemas constructivos no tienen un especial interés porque el vidrio laminado está siempre soportado por otro elemento de acero o incluso vidrio en forma de retícula. En la presente tesis voy a desarrollar una nueva solución de elemento autoportante de vidrio de gran tamaño haciendo seguro el uso del elemento para andar en el aire. El sueño de muchos arquitectos ha sido diseñar un edificio completamente transparente y a mí me gustaría contribuir a este sueño empezando a estudiar un forjado de vidrio como elemento estructural horizontal y para ello debemos cumplir requerimientos de seguridad. Uno de los objetivos es lograr un elemento lo más transparente y esbelto posible para el uso de pasarelas en vestíbulos de edificios. Las referencias construidas son bien conocidas, pero por otro lado Universidades europeas estudian continua estudiando el comportamiento del vidrio con diferentes láminas, adhesivos, apilados, insertos, sistemas de laminado, pretensado, pandeo lateral, seguridad post-rotura y muchos más aspectos necesarios. La metodología llevada a cabo en esta tesis ha sido primeramente diseñar un elemento industrial prefabricado horizontal de vidrio teniendo en cuenta todos los conceptos aprendidos en el estado del arte y la investigación para poder predimensionar el elemento. El siguiente paso será verificar el modelo por medio de cálculo analítico, simulación de elementos finitos y ensayos físicos. Para realizar los ensayos hay un paso intermedio teniendo que cambiar la hipótesis de carga uniforme a carga puntal para realizar el ensayo de flexión a 4 puntos normalizado y además cambiar a escala 1:2 para adaptarse al espacio de ensayo y ser viable económicamente. Finalmente compararé los resultados de tensión y deformación obtenidos por los tres métodos para extraer conclusiones. Sin embargo el problema de la seguridad no ha concluido, tendré que demostrar que el sistema es seguro después de que se produzca la rotura y para ello sólo dispongo de los ensayos como medio de demostración. El diseño es el resultado de la evolución de una viga tipo “I”; cuando es pretensada para obtener más resistencia, aparece el problema de pandeo lateral y éste es solucionado con una viga con sección en “T” cuya unión es resuelta con un cajeado longitudinal en la parte inferior del elemento horizontal. Las alas de éste crecen para recoger las cargas superficiales creando a su vez un punto débil en la unión que a su vez se soluciona duplicando la sección “TT” y haciendo trabajar dicho tablero de forma tan óptima como una viga continua. Dicha sección en vidrio como un único elemento pretensado es algo inédito. Además he diseñado unas escuadras metálicas en los extremos de los nervios como apoyo y placa de pretensión, así como una hendidura curva en el centro de los nervios para alojar los tirantes de acero de modo que al pretensar el tirante la placa corrija al menos la deformación por peso propio. Realizados los cambios geométricos de escala y las simplificaciones en el laminado y el adhesivo se programan la extracción de resultados desde 3 estadios diferentes: Sin pretensión y con pretensión de 750 Kg y de 1000Kg en cada nervio. Por cada estadio y por cada uno de los métodos, cálculo, simulación y ensayos, se extraen los datos de deformación y tensión en el punto medio de un nervio con el objetivo de hacer una comparación de resultados para obtener unas conclusiones, siempre en el campo de la elasticidad. Posteriormente incrementaré la carga hasta el momento de la rotura de la placa y después hasta el colapso teniendo en cuenta el tiempo y demostrando una rotura segura. El vidrio no tendrá un comportamiento plástico pero habrá sido controlado su comportamiento frágil manteniendo una carga y una deformación aceptable. ABSTRACT Over the past few years we have realized the importance of the new technologies regarding the application of glass in new buildings, especially those touristic places were the views and the heights are the reason of the visit. However, the construction systems of these glass platforms are not usually as interesting, because the laminated glass is always held by another steel substructure or even a grid-formed glass element. Throughout this thesis I am going to develop a new solution of a self-bearing element with big dimensions made out of glass, ensuring a safe solution to use as an element to walk on the air. The dream of many architects has been to create a building completely transparent, and I would like to contribute to this idea by making a glass slab as a horizontal structural element, for which we have to meet the security requirements. One of the goals is to achieve an element as transparent and slim as possible for the use in walkways of building lobbies. The glass buildings references are well known, but on the other hand the European Universities study the behaviour of the glass with different interlayers, adhesives, laminating systems, stacking, prestressed, buckling, safety, breakage and post-breakage capacity; and many other necessary aspects. The methodology followed in this thesis has been to first create a horizontal industrial prefabricated horizontal element of glass, taking into account all the concepts learned in the state of art and the investigation to be able to predimension this element. The next step will be to verify this model with an analytic calculus, a finite element modelling simulation and physical tests. To fulfil these tests there is an intermediate step, having to change the load hypothesis from a punctual one to make the test with a four points normalized deflexion, and also the scale of the sample was changed to 1:2 to adapt to the space of the test and make it economically possible. Finally, the results of tension and deformation obtained from the three methods have been compared to make the conclusions. However, the problem with safety has not concluded yet, for I will have to demonstrate that this system is safe even after its breakage, for which I can only use physical tests as a way of demonstration. The design is the result of the evolution of a typical “I” beam, which when it is prestressed to achieve more resistance, the effect of buckling overcomes, and this is solved with a “T” shaped beam, where the union is solved with a longitudinal groove on the inferior part of the horizontal element. The boards of this beam grow to cover the superficial loads, creating at the same time a weak point, which is solved by duplicating the section “TT” and therefore making this board work as optimal as a continuous beam. This glass section as a single prestressed element is unique. After the final design of the “π” glass plate was obtained and the composition of the laminated glass and interlayers has been predimensioned, the last connection elements must be contemplated. I have also designed a square steel shoe at the end of the beams, which will be the base and the prestressed board, as well as a curved slot in the centre of the nerves to accommodate the steel braces so that when this brace prestresses the board, at least the deformation due to its self-weight will be amended. Once I made the geometric changes of the scale and the simplifications on the laminating and the adhesive, the extraction on results overcomes from three different stages: without any pretension, with a pretension of 750 kg and with a pretension of 1000 kg on each rib. For each stage and for each one of the methods, calculus, simulation and tests, the deformation datum were extracted to obtain the conclusions, always in the field of the elasticity. Afterwards, I will increase the load until the moment of breakage of this board, and then until the collapse of the element, taking into account the time spent and demonstrating a safe breakage. The glass will not have a plastic behaviour, but its brittle behaviour has been controlled, keeping an acceptable load and deflection.

Animal performance and meat characteristics in steers reared in intensive conditions fed with different vegetable oils

Enhancing the quality of beef meat is an important goal in terms of improving both the nutritional value for the consumer and the commercial value for producers. The aim of this work was to study the effects of different vegetable oil supplements on growth performance, carcass quality and meat quality in beef steers reared under intensive conditions. A total of 240 Blonde D? Aquitaine steers (average BW = 293.7 ± 38.88 kg) were grouped into 24 batches (10 steers/batch) and were randomly assigned to one of the three dietary treatments (eight batches per treatment), each supplemented with either 4% hydrogenated palm oil (PALM) or fatty acids (FAs) from olive oil (OLI) or soybean oil (SOY). No differences in growth performance or carcass quality were observed. For the meat quality analysis, a steer was randomly selected from each batch and the 6th rib on the left half of the carcass was dissected. PALM meat had the highest percentage of 16:0 ( P< 0.05) and the lowest n-6/n-3 polyunsaturated fatty acids (PUFA) ratio ( P< 0.05), OLI had the highest content of t 11-18:1 ( P< 0.01) and c 9,t 11-18:2 ( P< 0.05) and SOY showed the lowest value of monounsaturated fatty acids (MUFA) ( P< 0.001), the highest percentage of PUFA ( P< 0.01) and a lower index of atherogenicity ( P = 0.07) than PALM. No significant differences in the sensory characteristics of the meat were noted. However, the results of the principal component analysis of meat characteristics enabled meat from those steers that consumed fatty acids from olive oil to be differentiated from that of steers that consumed soybean oil.

Desenvolvimento de materiais nanoestruturados à base de SiO2-Nb2O5 preparados por uma nova rota sol-gel com aplicações em fotônica

Este trabalho concentra-se na preparação e caracterizações estrutural e espectroscópica de materiais nanoestruturados à base de SiO2-Nb2O5 dopados e codopados com íons Er3+, Yb3+ e Eu3+ na forma de pós e guias de onda planares. Os nanocompósitos foram preparados através de uma nova rota sol-gel utilizando óxido de nióbio como precursor em substituição ao alcóxido de nióbio. A correlação estrutura propriedades luminescentes foi estudada por difração de raios X, microscopia eletrônica de transmissão, espectroscopia vibracional de absorção no infravermelho, espectroscopia vibracional de espalhamento Raman, análise térmica, reflectância difusa e especular, espectroscopia de fotoluminescência e acoplamento M-line. Inicialmente foi avaliado a influência da concentração de nióbio nas propriedades estruturais e luminescentes de nanocompósitos (100-x)Si-xNb dopados e codopados com íons Er3+, Yb3+ e Eu3+ tratados termicamente a 900 °C por 3h. A cristalização do Nb2O5 foi dependente da concentração de Nb na matriz, com a distribuição dos íons lantanídeos preferencialmente no Nb2O5, afetando as propriedades luminescentes. Para os nanocompósitos codopados com íons Er3+ e Yb3+ foram obtidos valores de largura de banda a meia altura (FWHM) da ordem de 70 nm na região de 1550 nm e tempos de vida de até 5,2 ms. A emissão na região do visível, decorrente de processos de conversão ascendente, revelou-se dependente da concentração de nióbio. Foi verificada emissão preferencial na região do verde para menores concentrações de Nb. Enquanto que, para as maiores concentrações, processos de relaxação cruzada levaram a um aumento relativo na intensidade de emissão na região do vermelho. A eficiência quântica de emissão dos nanocompósitos (100-x)Si-xNb dopados com Eu3+ variou com o comprimento de onda de excitação, refletindo os diferentes sítios de simetria ocupados por este íons nesta estrutura complexa. A influência da temperatura de tratamento térmico no processo de cristalização do Nb2O5 em nanocompósitos 70Si:30Nb codopados com íons Er3+ e Yb3+ foi avaliada. Material amorfo foi obtido a 700 °C enquanto que a 900 e 1100 °C foram identificas as fases ortorrômbica (fase T) e monoclínica (fase M) do Nb2O5. Intensa emissão na região de 1550 nm com valores de FWHM de 52 e 67 nm e tempos de vida de 5,6 e 5,4 ms foram verificados a 700 e 900 °C sob excitação em 977 nm, respectivamente. Por fim, foram obtidos guias de onda planares com excelentes propriedades ópticas e com grande potencial de aplicação em dispositivos de amplificação óptica. Especificamente, materiais fotônicos com banda larga de emissão na região do infravermelho foram preparados, indicando fortemente a potencialidade para a aplicação em telecomunicações envolvendo não somente a banda C como também as bandas L e S em materiais contendo somente íons Er3+ como centros emissores.

Método da propagação de feixe de ângulo largo para análise de guias de ondas ópticos não-lineares

Este trabalho propõe uma extensão do método de propagação de feixe (BPM - Beam Propagation Method) para a análise de guias de ondas ópticos e acopladores baseados em materiais não-lineares do tipo Kerr. Este método se destina à investigação de estruturas onde a utilização da equação escalar de Helmholtz (EEH) em seu limite paraxial não mais se aplica. Os métodos desenvolvidos para este fim são denominados na literatura como métodos de propagação de feixe de ângulo largo. O formalismo aqui desenvolvido é baseado na técnica das diferenças finitas e nos esquemas de Crank-Nicholson (CN) e Douglas generalizado (GD). Estes esquemas apresentam como característica o fato de apresentarem um erro de truncamento em relação ao passo de discretização transversal, Δx, proporcional a O(Δx2) para o primeiro e O(Δx4). A convergência do método em ambos esquemas é otimizada pela utilização de um algoritmo interativo para a correção do campo no meio não-linear. O formalismo de ângulo largo é obtido pela expansão da EEH para os esquemas CN e GD em termos de polinômios aproximantes de Padé de ordem (1,0) e (1,1) para CN e GD, e (2,2) e (3,3) para CN. Os aproximantes de ordem superior a (1,1) apresentam sérios problemas de estabilidade. Este problema é eliminado pela rotação dos aproximantes no plano complexo. Duas condições de contorno nos extremos da janela computacional são também investigadas: 1) (TBC - Transparent Boundary Condition) e 2) condição de contorno absorvente (TAB - Transparent Absorbing Boundary). Estas condições de contorno possuem a facilidade de evitar que reflexões indesejáveis sejam transmitidas para dentro da janela computacional. Um estudo comparativo da influência destas condições de contorno na solução de guias de ondas ópticos não-lineares é também abordada neste trabalho.

Produção e caracterização de guias de onda dopados com terras-raras contendo nanopartículas semicondutoras.

O presente trabalho tem como objetivo estudar a produção e caracterização de filmes finos do tipo GeO2-Bi2O3 (BGO) produzidos por sputtering-RF com e sem nanopartículas (NPs) semicondutoras, dopados e codopados com íons de Er3+ ou Er3+/Yb3+ para a produção de amplificadores ópticos. A produção de guias de onda do tipo pedestal baseados nos filmes BGO foi realizada a partir de litografia óptica seguida por processo de corrosão por plasma e deposição física a vapor. A incorporação dos íons de terras-raras (TRs) foi verificada a partir dos espectros de emissão. Análises de espectroscopia e microscopia foram indispensáveis para otimizar os parâmetros dos processos para a construção dos guias de onda. Foi observado aumento significativo da luminescência do Er3+ (região do visível e do infravermelho), em filmes finos codopados com Er3+/Yb3+ na presença de nanopartículas de Si. As perdas por propagação mínimas observadas foram de ~1,75 dB/cm para os guias pedestal em 1068 nm. Para os guias dopados com Er3+ foi observado aumento significativo do ganho na presença de NPs de silício (1,8 dB/cm). O ganho óptico nos guias de onda amplificadores codopados com Er3+/Yb3+ e dopados com Er3+ com e sem NPs de silício também foi medido. Ganho de ~8dB/cm em 1542 nm, sob excitação em 980 nm, foi observado para os guias pedestal codopados com Er3+/Yb3+ (Er = 4,64.1019 átomos/cm3, Yb = 3,60.1020 átomos/cm3) com largura de 80 µm; para os guias codopados com concentração superior de Er3+/Yb3+ (Er = 1,34.1021 átomos/cm3, Yb = 3,90.1021 átomos/cm3) e com NPs de Si, foi observado aumento do ganho óptico de 50% para guia com largura de 100 µm. Os resultados apresentados demonstram que guias de onda baseados em germanatos, com ou sem NPs semicondutoras, são promissores para aplicações em dispositivos fotônicos.

Estudo e aplicação de guias de ondas integrados ao substrato em frequências de micro-ondas.

Esse trabalho de pesquisa apresenta um estudo detalhado sobre guias de ondas integrados ao substrato (SIW) operando em frequências de micro-ondas com base na teoria de guias de ondas retangulares (RWG). O estudo sobre guias SIW associa equações apresentadas na literatura e utiliza simulações eletromagnéticas para desenvolver um procedimento de projeto bem definido. É considerada a integração entre guias SIW e linhas de transmissão de microfita, projetando-se transições entre essas duas estruturas com o propósito de prover casamento de impedância e de viabilizar a caracterização em frequências de micro-ondas. São apresentadas considerações sobre processos de fabricação de circuitos SIW em substratos constituídos por laminados de alta frequência. Uma vez estabelecidos os procedimentos de fabricação e os critérios de projeto, a tecnologia SIW é aplicada ao projeto de três guias de ondas SIW nas bandas S e X, que foram fabricados empregando laminados de alta-frequência. Foram projetados dois filtros SIW passa-faixa empregando cavidades ressonantes e postes metálicos indutivos. Os dois filtros operam na frequência central de 10,61 GHz, sendo que um deles tem banda de passagem de 7,5%e é de 3ª ordem e o outro filtro tem banda de passagem de 15%, sendo de 5ª ordem. Foram realizadas comparações entre o desempenho simulado e experimental das estruturas SIW projetadas. Os resultados de simulações eletromagnéticas e experimentais demonstraram boa concordância. Os projetos em tecnologia SIW apresentados neste trabalho de pesquisa possuem perdas de retorno melhores que 10 dB na banda de operação e perdas por inserção de 1,0 dB a 1,5 dB. É apresentada a análise da sensibilidade do desempenho dos guias de ondas e filtros SIW projetados a desvios dimensionais típicos do processo de fabricação por microfresagem mecânica. Com os resultados experimentais e de simulação foi possível validar os procedimentos de projeto e de fabricação de circuitos SIW operando em frequências de micro-ondas.

Espiritualidad y defensa al servicio de la comunidad musulmana de al-Andalus: las rábitas en Portugal

Se analizan los conceptos de guerra y paz en los orígenes del islam, y se repasan los acontecimientos y justificación inicial de la guerra como necesaria para el sustento de la nueva comunidad de fieles y cómo se llega a institucionalizar el ŷihād como precepto. Cuando no es posible realizar este, como sustituto del ŷihād se desarrolla el espíritu del ribāṭ. Se explica la evolución hacia una espiritualización de este precepto, desarrollada inicialmente en «lugares de ribāṭ» y luego en las rábitas. Finalmente, se resumen los datos toponímicos y arqueológicos que conocemos sobre las rábitas en Portugal.

Astrophysical parameters of LS 2883 and implications for the PSR B1259-63 gamma-ray binary

Only a few binary systems with compact objects display TeV emission. The physical properties of the companion stars represent basic input for understanding the physical mechanisms behind the particle acceleration, emission, and absorption processes in these so-called gamma-ray binaries. Here we present high-resolution and high signal-to-noise optical spectra of LS 2883, the Be star forming a gamma-ray binary with the young non-accreting pulsar PSR B1259-63, showing it to rotate faster and be significantly earlier and more luminous than previously thought. Analysis of the interstellar lines suggests that the system is located at the same distance as (and thus is likely a member of) Cen OB1. Taking the distance to the association, d = 2.3 kpc, and a color excess of E(B – V) = 0.85 for LS 2883 results in MV ≈ –4.4. Because of fast rotation, LS 2883 is oblate (R eq sime 9.7 R ☉ and R pole sime 8.1 R ☉) and presents a temperature gradient (T eq≈ 27,500 K, log g eq = 3.7; T pole≈ 34,000 K, log g pole = 4.1). If the star did not rotate, it would have parameters corresponding to a late O-type star. We estimate its luminosity at log(L */L ☉) sime 4.79 and its mass at M * ≈ 30 M ☉. The mass function then implies an inclination of the binary system i orb ≈ 23°, slightly smaller than previous estimates. We discuss the implications of these new astrophysical parameters of LS 2883 for the production of high-energy and very high-energy gamma rays in the PSR B1259-63/LS 2883 gamma-ray binary system. In particular, the stellar properties are very important for prediction of the line-like bulk Comptonization component from the unshocked ultrarelativistic pulsar wind.

A Be-type star with a black-hole companion

Stellar-mass black holes have all been discovered through X-ray emission, which arises from the accretion of gas from their binary companions (this gas is either stripped from low-mass stars or supplied as winds from massive ones). Binary evolution models also predict the existence of black holes accreting from the equatorial envelope of rapidly spinning Be-type stars1, 2, 3 (stars of the Be type are hot blue irregular variables showing characteristic spectral emission lines of hydrogen). Of the approximately 80 Be X-ray binaries known in the Galaxy, however, only pulsating neutron stars have been found as companions2, 3, 4. A black hole was formally allowed as a solution for the companion to the Be star MWC 656 (ref. 5; also known as HD 215227), although that conclusion was based on a single radial velocity curve of the Be star, a mistaken spectral classification6 and rough estimates of the inclination angle. Here we report observations of an accretion disk line mirroring the orbit of MWC 656. This, together with an improved radial velocity curve of the Be star through fitting sharp Fe ii profiles from the equatorial disk, and a refined Be classification (to that of a B1.5–B2 III star), indicates that a black hole of 3.8 to 6.9 solar masses orbits MWC 656, the candidate counterpart of the γ-ray source AGL J2241+4454 (refs 5, 6). The black hole is X-ray quiescent and fed by a radiatively inefficient accretion flow giving a luminosity less than 1.6 × 10−7 times the Eddington luminosity. This implies that Be binaries with black-hole companions are difficult to detect in conventional X-ray surveys.

On the formation and evolution of the first Be star in a black hole binary MWC 656

We find that the formation of MWC 656 (the first Be binary containing a black hole) involves a common envelope phase and a supernova explosion. This result supports the idea that a rapidly rotating Be star can emerge out of a common envelope phase, which is very intriguing because this evolutionary stage is thought to be too fast to lead to significant accretion and spin up of the B star. We predict ∼10–100 of B-BH binaries to currently reside in the Galactic disc, among which around 1/3 contain a Be star, but there is only a small chance to observe a system with parameters resembling MWC 656. If MWC 656 is representative of intrinsic Galactic Be-BH binary population, it may indicate that standard evolutionary theory needs to be revised. This would pose another evolutionary problem in understanding black hole (BH) binaries, with BH X-ray novae formation issue being the prime example. Future evolution of MWC 656 with an ∼5 M⊙ BH and with an ∼13 M⊙ main-sequence companion on an ∼60 d orbit may lead to the formation of a coalescing BH–NS (neutron star) system. The estimated Advanced LIGO/Virgo detection rate of such systems is up to ∼0.2 yr−1. This empirical estimate is a lower limit as it is obtained with only one particular evolutionary scenario, the MWC 656 binary. This is only a third such estimate available (after Cyg X-1 and Cyg X-3), and it lends additional support to the existence of so far undetected BH–NS binaries.

Almonastires y rábitas: espiritualidad islámica individual y defensa colectiva de la comunidad. Espiritualidad y geopolítica en los orígenes de Almonaster la Real

Primeramente se describe el ŷihād, su origen coránico, la escatología asociada y el derecho musulmán asociado al mismo, para acabar explicando cómo el espíritu colectivo y estatal del ŷihād evolucionó hacia la espiritualidad individual del ribāṭ en Al-Andalus. En la segunda parte se enumeran los topónimos al-Munastīr en la península Ibérica, asociados a construcciones eclesiásticas visigodas precedentes, y se explica la geopolítica de Almonaster la Real: en la vía romana que comunicaba Sevilla y Huelva por la montaña onubense con Beja, esta vía de origen romano se usó hasta fin del s. X. La vigilancia en época omeya de este itinerario esencial de comunicación con Portugal dio origen a este “lugar de ribāṭ” que fue Almonaster, fundado sobre restos tardorromanos precedentes.