Potential for synthetic gas in Finnish industry

Finland, other Nordic countries and European Union aim to decarbonize their energy production by 2050. Decarbonization requires large scale implementation of non-emission energy sources, i.e. renewable energy and nuclear power. Stochastic renewable energy sources present a challenge to balance the supply and demand for energy. Energy storages, non-emissions fuels in mobility and industrial processes are required whenever electrification is not possible. Neo-Carbon project studies the decarbonizing the energy production and the role of synthetic gas in it. This thesis studies the industrial processes in steel production, oil refining, cement manufacturing and glass manufacturing, where natural gas is already used or fuel switch to SNG is possible. The technical potential for fuel switching is assessed, and economic potential is necessary after this. All studied processes have potential for fuel switching, but total decarbonization of steel production, oil refining requires implementation of other zero-emission technologies.

Review of water electrolysis technologies and design of renewable hydrogen production systems

An electric system based on renewable energy faces challenges concerning the storage and utilization of energy due to the intermittent and seasonal nature of renewable energy sources. Wind and solar photovoltaic power productions are variable and difficult to predict, and thus electricity storage will be needed in the case of basic power production. Hydrogen’s energetic potential lies in its ability and versatility to store chemical energy, to serve as an energy carrier and as feedstock for various industries. Hydrogen is also used e.g. in the production of biofuels. The amount of energy produced during hydrogen combustion is higher than any other fuel’s on a mass basis with a higher-heating-value of 39.4 kWh/kg. However, even though hydrogen is the most abundant element in the universe, on Earth most hydrogen exists in molecular forms such as water. Therefore, hydrogen must be produced and there are various methods to do so. Today, the majority hydrogen comes from fossil fuels, mainly from steam methane reforming, and only about 4 % of global hydrogen comes from water electrolysis. Combination of electrolytic production of hydrogen from water and supply of renewable energy is attracting more interest due to the sustainability and the increased flexibility of the resulting energy system. The preferred option for intermittent hydrogen storage is pressurization in tanks since at ambient conditions the volumetric energy density of hydrogen is low, and pressurized tanks are efficient and affordable when the cycling rate is high. Pressurized hydrogen enables energy storage in larger capacities compared to battery technologies and additionally the energy can be stored for longer periods of time, on a time scale of months. In this thesis, the thermodynamics and electrochemistry associated with water electrolysis are described. The main water electrolysis technologies are presented with state-of-the-art specifications. Finally, a Power-to-Hydrogen infrastructure design for Lappeenranta University of Technology is presented. Laboratory setup for water electrolysis is specified and factors affecting its commissioning in Finland are presented.

Intensification of hemicellulose hot-water extraction from spruce wood by parameter tuning

The growing population on earth along with diminishing fossil deposits and the climate change debate calls out for a better utilization of renewable, bio-based materials. In a biorefinery perspective, the renewable biomass is converted into many different products such as fuels, chemicals, and materials, quite similar to the petroleum refinery industry. Since forests cover about one third of the land surface on earth, ligno-cellulosic biomass is the most abundant renewable resource available. The natural first step in a biorefinery is separation and isolation of the different compounds the biomass is comprised of. The major components in wood are cellulose, hemicellulose, and lignin, all of which can be made into various end-products. Today, focus normally lies on utilizing only one component, e.g., the cellulose in the Kraft pulping process. It would be highly desirable to utilize all the different compounds, both from an economical and environmental point of view. The separation process should therefore be optimized. Hemicelluloses can partly be extracted with hot-water prior to pulping. Depending in the severity of the extraction, the hemicelluloses are degraded to various degrees. In order to be able to choose from a variety of different end-products, the hemicelluloses should be as intact as possible after the extraction. The main focus of this work has been on preserving the hemicellulose molar mass throughout the extraction at a high yield by actively controlling the extraction pH at the high temperatures used. Since it has not been possible to measure pH during an extraction due to the high temperatures, the extraction pH has remained a “black box”. Therefore, a high-temperature in-line pH measuring system was developed, validated, and tested for hot-water wood extractions. One crucial step in the measurements is calibration, therefore extensive efforts was put on developing a reliable calibration procedure. Initial extractions with wood showed that the actual extraction pH was ~0.35 pH units higher than previously believed. The measuring system was also equipped with a controller connected to a pump. With this addition it was possible to control the extraction to any desired pH set point. When the pH dropped below the set point, the controller started pumping in alkali and by that the desired set point was maintained very accurately. Analyses of the extracted hemicelluloses showed that less hemicelluloses were extracted at higher pH but with a higher molar-mass. Monomer formation could, at a certain pH level, be completely inhibited. Increasing the temperature, but maintaining a specific pH set point, would speed up the extraction without degrading the molar-mass of the hemicelluloses and thereby intensifying the extraction. The diffusion of the dissolved hemicelluloses from the wood particle is a major part of the extraction process. Therefore, a particle size study ranging from 0.5 mm wood particles to industrial size wood chips was conducted to investigate the internal mass transfer of the hemicelluloses. Unsurprisingly, it showed that hemicelluloses were extracted faster from smaller wood particles than larger although it did not seem to have a substantial effect on the average molar mass of the extracted hemicelluloses. However, smaller particle sizes require more energy to manufacture and thus increases the economic cost. Since bark comprises 10 – 15 % of a tree, it is important to also consider it in a biorefinery concept. Spruce inner and outer bark was hot-water extracted separately to investigate the possibility to isolate the bark hemicelluloses. It was showed that the bark hemicelluloses comprised mostly of pectic material and differed considerably from the wood hemicelluloses. The bark hemicelluloses, or pectins, could be extracted at lower temperatures than the wood hemicelluloses. A chemical characterization, done separately on inner and outer bark, showed that inner bark contained over 10 % stilbene glucosides that could be extracted already at 100 °C with aqueous acetone.

Advanced biofuel production: Engineering metabolic pathways for butanol and propane biosynthesis.

Greenhouse gases emitted from energy production and transportation are dramatically changing the climate of Planet Earth. As a consequence, global warming is affecting the living conditions of numerous plant and animal species, including ours. Thus the development of sustainable and renewable liquid fuels is an essential global challenge in order to combat the climate change. In the past decades many technologies have been developed as alternatives to currently used petroleum fuels, such as bioethanol and biodiesel. However, even with gradually increasing production, the market penetration of these first generation biofuels is still relatively small compared to fossil fuels. Researchers have long ago realized that there is a need for advanced biofuels with improved physical and chemical properties compared to bioethanol and with biomass raw materials not competing with food production. Several target molecules have been identified as potential fuel candidates, such as alkanes, fatty acids, long carbon‐chain alcohols and isoprenoids. The current study focuses on the biosynthesis of butanol and propane as possible biofuels. The scope of this research was to investigate novel heterologous metabolic pathways and to identify bottlenecks for alcohol and alkane generation using Escherichia coli as a model host microorganism. The first theme of the work studied the pathways generating butyraldehyde, the common denominator for butanol and propane biosynthesis. Two ways of generating butyraldehyde were described, one via the bacterial fatty acid elongation machinery and the other via partial overexpression of the acetone‐butanol‐ethanol fermentation pathway found in Clostridium acetobutylicum. The second theme of the experimental work studied the reduction of butyraldehyde to butanol catalysed by various bacterial aldehyde‐reductase enzymes, whereas the final part of the work investigated the in vivo kinetics of the cyanobacterial aldehyde deformylating oxygenase (ADO) for the generation of hydrocarbons. The results showed that the novel butanol pathway, based on fatty acid biosynthesis consisting of an acyl‐ACP thioesterase and a carboxylic acid reductase, is tolerant to oxygen, thus being an efficient alternative to the previous Clostridial pathways. It was also shown that butanol can be produced from acetyl‐CoA using acetoacetyl CoA synthase (NphT7) or acetyl‐CoA acetyltransferase (AtoB) enzymes. The study also demonstrated, for the first time, that bacterial biosynthesis of propane is possible. The efficiency of the system is clearly limited by the poor kinetic properties of the ADO enzyme, and for proper function in vivo, the catalytic machinery requires a coupled electron relay system.

Promoting Growth in the Use of Bioenergy in Europe by Converting Existing Coal-Fired Power Plants to Biomass

Repowering existing power plants by replacing coal with biomass might offer an interesting option to ease the transition from fossil fuels to renewable energy sources and promote a fur-ther expansion of bioenergy in Europe, on account of the potential to decrease greenhouse gas emissions, as well as other pollutants (SOx, NOx, etcetera). In addition, a great part of the appeal of repowering projects comes from the opportunity to reuse the vast existing invest-ment and infrastructure associated with coal-based power generation. Even so, only a limited number of experiences with repowering are found. Therefore, efforts are required to produce technical and scientific evidence to determine whether said technology might be considered feasible for its adoption within European conditions. A detailed evaluation of the technical and economic aspects of this technology constitutes a powerful tool for decision makers to define the energy future for Europe. To better illustrate this concept, a case study is analyzed. A Slovakian pulverized coal plant was used as the basis for determining the effects on perfor-mance, operation, maintenance and cost when fuel is shifted to biomass. It was found that biomass fuel properties play a crucial role in plant repowering. Furthermore, results demon-strate that this technology offers renewable energy with low pollutant emissions at the cost of reduced capacity, relatively high levelized cost of electricity and sometimes, a maintenance-intensive operation. Lastly, regardless of the fact that existing equipment can be reutilized for the most part, extensive additions/modifications may be required to ensure a safe operation and an acceptable performance.

Biomassan käsittely voimalaitoksissa

Tässä diplomityössä tutkitaan biomassan esikäsittelyä suurissa voimalaitoksissa. Työssä keskitytään puusta saataviin polttoaineisiin. Biomassan esikäsittely on tärkeä osa voimalaitoksen toimintaa. Sillä pyritään saamaan puulle halutut ominaisuudet loppukäyttöä, kuten polttoa tai kaasutusta varten. Puubiomassan tärkeimpiä ominaisuuksia ovat kosteus, palakoko ja tasalaatuisuus. Työ on jaettu neljään osaan. Ensimmäisessä osassa tutkitaan kiinteän biomassan ominaisuuksia ja ongelmia. Toisessa osassa esitellään erilaisia voimalaitoksissa käytettäviä puubiomassoja ja niiden erityisominaisuuksia ja -vaatimuksia. Kolmannessa osassa esitellään biomassan käsittelyä voimalaitoksella. Käsittely jaotellaan vastaanottoon, esikäsittelyyn, varastointiin ja käsittelylaitteistoihin. Kolmannessa osassa tutkitaan myös käsittelyn erityisvaatimuksia ja esitellään esimerkkejä biomassan kokonaiskäsittelystä laitoksella. Työn neljäs osa paneutuu biomassan käsittelyn turvallisuus- ja ympäristöasioihin. Puubiomassan esikäsittely on suunniteltava käytettävien puulaatujen ja -määrien mukaan. Biomassan kosteuden ollessa korkea, on tutkittava onko kuivurien käyttö kannattavaa ja perusteltua. Jos voimalaitokselle tuleva puu on epätasalaatuista tai sisältää epäpuhtauksia, on käytettävä erilaisia puhdistus- ja murskainlaitteistoja. Biomassan käsittelyssä syntyy melua ja päästöjä. Ympäristö- ja terveyshaittojen ehkäisemiseksi käsittelylaitteistoihin on suunniteltava tarpeelliset suojat ja varojärjestelmät.

Leijukerroslämmönsiirtimien tukkeutuminen biovoimalaitoksessa

Leijukerroslämmönsiirtimien, eli hiekanpalautuspolvessa sijaitsevien tulistimien tukkeutuminen on ollut Kaukaan Voima Oy:n biovoimalaitoksen suunnittelemattomien seisokkien suurin syy vuodesta 2012 lähtien. Tulistimet tukkeutuvat kahdella tavalla. Nopeassa tukkeutumisessa tulistinkammion seinien kuonakerrostumat romahtavat yhtäkkiä tulistimen päälle tukkien sen. Tämä johtaa aina koko laitoksen alasajoon. Hitaassa tukkeutumisessa tulistinputkien pinnalle muodostuu vähitellen kerrostuma sekä tulistinputkien väliin jää suurempia kappaleita, jotka tukkivat tulistinta. Nopea tukkeutuminen johtuu tuhkassa olevien alkali-, eli kalium- ja natriumyhdisteiden synnyttämistä kerrostumista lämmönsiirrinkammion seinille. Hidas tukkeutuminen johtuu osittain myös alkaliyhdisteistä, mutta merkittävämpi aine tulistinputkien pinnalla olevassa kerrostumissa näyttää olevan kalsiumsulfaatti, joka tukkii tulistinta. Palavan aineen pääsy tulistinkammioon ilmanjakoasetuksista ja tulistinkammion rakenteesta johtuen aiheuttaa kerrostumien syntymisen. Kerrostumien syntymiseen johtavat syyt johtuvat monesta tekijästä ja yksiselitteistä aiheuttajaa on vaikea määritellä. Selvin yhteys on lietteen epätasaisessa poltossa ja turpeen käytössä. Nykyisillä lietteenkäsittelylaitteilla lietteen tasainen syöttö on vaikeaa ja se aiheuttaa ongelmia. Turpeen poltto biopolttoaineiden rinnalla pitää tulistimet puhtaampina. Muita todennäköisiä kerrostumia lisääviä syitä ovat puhtaan hiekan vähäinen syöttömäärä ja usean huonomman polttoaineen yhtäaikainen poltto.

Metsäteollisuuden ympäristöstrategia hallinnon näkökulmasta: Metsäteollisuuden kehitysskenaariot vuoteen 2020

Suomen metsäteollisuus elää voimakasta uusiutumis- ja murrosvaihetta, joka ilmenee muutoksina yksittäisten tehtaiden ja tehdasintegraattien toiminnassa. Monia yksikköjä on poistunut tuotannosta ja tuotannon painotusta on muutettu. Toisaalta metsäteollisuus on suuntaamassa uusille aloille, jolloin tuotteina voivat olla esimerkiksi erilaiset biopolttoaineet, kemianteollisuuden raaka-aineet ja uuden sukupolven paperi- ja kartonkituotteet. Metsäteollisuuden muuttuminen ja laitosten monimutkaistuminen sekä jatkuvasti lisääntyvä tiedontarve asettavat yhä suurempia vaatimuksia sekä toiminnanharjoittajien ympäristövastaaville että viranomaisille. Hallinnon jatkuva muutos ja niukkenevat voimavarat voivat johtaa siihen, että käytännön lupa- ja valvontatyöhön jää yhä vähemmän aikaa. Kaakkois-Suomen ELY-keskuksen koordinoima hanke ”Metsäteollisuuden ympäristöstrategia vuoteen 2020 - hallinnon näkökulma” pyrkii vastaamaan edellä mainittuihin haasteisiin strategiatyön avulla. Hankkeen tarkoituksena oli tarkastella metsäteollisuuden ympäristönäkökohtia niistä lähtökohdista, joihin yritys voi vaikuttaa raaka-aineen tulosta tehtaalle ja tuotteen lähdöstä tehtaalta sekä tehtaan perustamisesta sulkemiseen ja jälkihoitoon asti. Tavoitteena oli määritellä toiminnoille toimiva ympäristöstrategia. Strategiassa pyrittiin löytämään yhteisymmärrys toiminnanharjoittajan ja viranomaisen kanssa mm. siitä, miten otetaan käyttöön parhaat käytännöt niin teollisuudessa kuin hallinnossakin, toimitaan uusien BAT-, IED- ja vesienhoitoperiaatteiden mukaisesti sekä edistetään kestävän kehityksen mukaisten tuotteiden markkinoille tuloa ja otetaan ennakointi tavaksi -lähtökohta käyttöön kaikessa toiminnassa. Hanketyössä esille nousseet haasteet ryhmiteltiin aihelueittain kolmeksi pääkohdaksi tärkeysjärjestyksessä: viranomaisen ja teollisuuden tiedonkulun ja tietämyksen parantaminen, lupa-, valvonta- ja hallintoprosessien parantaminen sekä uusien haasteiden kartoittaminen ja niihin reagointi. Haasteiden ratkaisukeinoiksi etsittiin käytännön toimenpiteitä sekä määriteltiin niille vastuutahot. Toimenpiteiksi esitettiin mm. viranomaisen ja teollisuuden yhteisiä koulutuspäiviä, asiantuntijapaneelin perustamista sekä lupamääräysten antamista myös tehtaan tai tuotantoyksikön sulkemisen tai muuttamisen varalle. Riittävien resurssien ja tietotaidon turvaaminen niin hallinnossa kuin teollisuudessa on ehdoton edellytys toimenpiteiden onnistumiselle

Deinking sludge utilization possibilities: technical, economic, and environmental assessments

This report introduces the ENPI project called “EMIR - Exploitation of Municipal and Industrial Residues” which was executed in a co-operation between Lappeenranta University of Technology (LUT), Saint Petersburg State University of Economics (SPbSUE), Saint Petersburg State Technical University of Plant Polymers (SPbSTUPP) and industrial partners from both Leningrad Region (LR), Russia and Finland. The main targets of the research were to identify the possibilities for deinking sludge management scenarios in co-operation with partner companies, to compare the sustainability of the alternatives, and to provide recommendations for the companies in the Leningrad Region on how to best manage deinking sludge. During the literature review, 24 deinking sludge utilization possibilities were identified, the majority falling under material recovery. Furthermore, 11 potential utilizers of deinking sludge were found within the search area determined by the transportation cost. Each potential utilizer was directly contacted in order to establish cooperation for deinking sludge utilization. Finally, four companies, namely, “Finnsementti” – a cement plant in Finland (S1), “St.Gobian Weber” – a light-weight aggregate plant in Finland (S2), “LSR-Cement” – a cement plant in LR (S3), and “Rockwool” – a stone wool plant in LR (S4) were seen as the most promising partners and were included in the economic and environmental assessments. Economic assessment using cost-benefit analysis (CBA) indicated that substitution of heavy fuel oil with dry deinking sludge in S2 was the most feasible option with a benefit/cost ratio (BCR) of 3.6 when all the sludge was utilized. At the same time, the use of 15% of the total sludge amount (the amount that could potentially be treated in the scenario) resulted in a BCR of only 0.16. The use of dry deinking sludge in the production of cement (S3) is a slightly more feasible option with a BCR of 1.1. The use of sludge in stone wool production is feasible only when all the deinking sludge is used and burned in an existing incineration plant. The least economically feasible utilization possibility is the use of sludge in cement production in Finland (S1) due to the high gate fee charged. Environmental assessment was performed applying internationally recognized life cycle assessment (LCA) methodologies: ISO 14040 and ISO 14044. The results of a consequential LCA stated that only S1 and S2 lead to a reduction of all environmental impacts within the impact categories chosen compared to the baseline scenario where deinking sludge is landfilled. Considering S1, the largest reduction of 13% was achieved for the global warming potential (GWP), whereas for S2, the largest decrease of abiotic depletion potential (ADP) was by 1.7%, the eutrophication potential (EP) by 1.8%, and a GWP of 2.1% was documented. In S3, the most notable increase of ADP and acidification potential (AP) by 2.6 and 1.5% was indicated, while the GWP was reduced by 12%, the largest out of all the impact categories. In S4, ADP and AP increased by 2.3 and 2.1% respectively, whereas ODP was reduced by 25%. During LCA, it was noticed that substitution of fuels causes a greater reduction of environmental impact (S1 and S2) than substitution of raw materials (S3 and S4). Despite a number of economically and environmentally acceptable deinking sludge utilization methods being assessed in the research, evaluation of bottlenecks and communications with companies’ representatives uncovered the fact that the availability of the raw materials consumed, and the risks associated with technological problems resulting from the sludge utilization, limited the willingness of industrial partners to start deinking sludge utilization. The research results are of high value for decision-makers at already existing paper mills since the result provide insights regarding alternatives to the deinking sludge utilization possibilities already applied. Thus, the research results support the maximum economic and environmental value recovery from waste paper utilization.

Lämmöntuotannon energiatehokkuuden parantaminen Sotek-säätiön rakennuksissa

Diplomityössä tarkastellaan lämmöntuotannon energiatehokkuuden parantamista neljässä Sotek- säätiön rakennuksessa. Työssä oli tarkoitus selvittää, minkälainen lämmitysjärjestelmä on juuri kyseiseen kiinteistöön järkevin ja investointikustannuksiltaan kannattava. Työssä käydään läpi polttoaineita, lämmöntuotanto- ja lämmönjakotapoja, sekä mietitään kannattaako rakennuksia lisäeristää. Työssä verrataan vanhojen järjestelmien hiilidioksidipäästöjä valittujen uusien järjestelmien hiilidioksidipäästöihin. Kiinteistöjen lämmitys tuottaa Suomessa noin 30 % kaikista hiilidioksidipäästöistä. Se on siis merkittävä alue, josta päästöjä voitaisiin vähentää. Tehtävänä oli laskea kaikille kiinteistöille tarkat lämmitystarpeet ja lämmitystehontarpeet käyttäen apuna Suomen rakennusmääräyskokoelmaa. Työn perusteella lämmöntuotannon energiatehokkuuden parantaminen kohteissa on järkevää ja taloudellisesti kannattavaa muuttamalla lämmöntuotanto pääosin lämpöpumpuille. Täystehoiset järjestelmät eivät tulleet investoinnillisesti kannattavaksi, eikä se ilmalämpöpumpuissa ollut edes mahdollista. Tulosten perusteella lämmitysenergian kustannuksia saatiin vähennettyä parhaiten mitoittamalla kohteisiin osatehoiset lämpöpumput. Lisälämmöneristäminen kohteissa ei taloudellisesti tullut kannattavaksi, vaikka lämmitystarve väheni. Lämmöntuotannon hiilidioksidipäästöt vähenisivät kohteissa keskimäärin noin 50 %.

Three-dimensional modeling of biomass fuel flow in a circulating fluidized bed furnace

The reduction of greenhouse gas emissions in the European Union promotes the combustion of biomass rather than fossil fuels in energy production. Circulating fluidized bed (CFB) combustion offers a simple, flexible and efficient way to utilize untreated biomass in a large scale. CFB furnaces are modeled in order to understand their operation better and to help in the design of new furnaces. Therefore, physically accurate models are needed to describe the heavily coupled multiphase flow, reactions and heat transfer inside the furnace. This thesis presents a new model for the fuel flow inside the CFB furnace, which acknowledges the physical properties of the fuel and the multiphase flow phenomena inside the furnace. This model is applied with special interest in the firing of untreated biomass. An experimental method is utilized to characterize gas-fuel drag force relations. This characteristic drag force approach is developed into a gas-fuel drag force model suitable for irregular, non-spherical biomass particles and applied together with the new fuel flow model in the modeling of a large-scale CFB furnace. The model results are physically valid and achieve very good correspondence with the measurement results from large-scale CFB furnace firing biomass. With the methods and models presented in this work, the fuel flow field inside a circulating fluidized bed furnace can be modeled with better accuracy and more efficiently than in previous studies with a three-dimensional holistic model frame.

Simultaneous allergen inactivation and detoxification of castor bean cake by treatment with calcium compounds

Ricinus communis L. is of great economic importance due to the oil extracted from its seeds. Castor oil has been used for pharmaceutical and industrial applications, as a lubricant or coating agent, as a component of plastic products, as a fungicide or in the synthesis of biodiesel fuels. After oil extraction, a castor cake with a large amount of protein is obtained. However, this by-product cannot be used as animal feed due to the presence of toxic (ricin) and allergenic (2S albumin) proteins. Here, we propose two processes for detoxification and allergen inactivation of the castor cake. In addition, we establish a biological test to detect ricin and validate these detoxification processes. In this test, Vero cells were treated with ricin, and cell death was assessed by cell counting and measurement of lactate dehydrogenase activity. The limit of detection of the Vero cell assay was 10 ng/mL using a concentration of 1.6 x 10(5) cells/well. Solid-state fermentation (SSF) and treatment with calcium compounds were used as cake detoxification processes. For SSF, Aspergillus niger was grown using a castor cake as a substrate, and this cake was analyzed after 24, 48, 72, and 96 h of SSF. Ricin was eliminated after 24 h of SSF treatment. The cake was treated with 4 or 8% Ca(OH)2 or CaO, and both the toxicity and the allergenic properties were entirely abolished. A by-product free of toxicity and allergens was obtained.

Association between NOx exposure and deaths caused by respiratory diseases in a medium-sized Brazilian city

Exposure to nitrogen oxides (NOx) emitted by burning fossil fuels has been associated with respiratory diseases. We aimed to estimate the effects of NOx exposure on mortality owing to respiratory diseases in residents of Taubaté, São Paulo, Brazil, of all ages and both sexes. This time-series ecological study from August 1, 2011 to July 31, 2012 used information on deaths caused by respiratory diseases obtained from the Health Department of Taubaté. Estimated daily levels of pollutants (NOx, particulate matter, ozone, carbon monoxide) were obtained from the Centro de Previsão de Tempo e Estudos Climáticos Coupled Aerosol and Tracer Transport model to the Brazilian developments on the Regional Atmospheric Modeling System. These environmental variables were used to adjust the multipollutant model for apparent temperature. To estimate association between hospitalizations owing to asthma and air pollutants, generalized additive Poisson regression models were developed, with lags as much as 5 days. There were 385 deaths with a daily mean (±SD) of 1.05±1.03 (range: 0-5). Exposure to NOx was significantly associated with mortality owing to respiratory diseases: relative risk (RR)=1.035 (95% confidence interval [CI]: 1.008-1.063) for lag 2, RR=1.064 (95%CI: 1.017-1.112) lag 3, RR=1.055 (95%CI: 1.025-1.085) lag 4, and RR=1.042 (95%CI: 1.010-1.076) lag 5. A 3 µg/m3 reduction in NOx concentration resulted in a decrease of 10-18 percentage points in risk of death caused by respiratory diseases. Even at NOx concentrations below the acceptable standard, there is association with deaths caused by respiratory diseases.

Kraft recovery boilers – Principles and practice

This book was created as postgraduate lecture notes for Lappeenranta University of Technology's special course of steam power plants. But as with anything ever written the ideas shown have nurtured for a long time. Parts of these chapters have appeared elsewhere as individual papers or work documents. One of the most helpful episodes have been presentations and discussions during Pohto Operator training seminars. Input from those sessions can be seen in chapter firing. You who run recovery boilers, I salute you. The purpose of this text is to give the reader an overview of recovery boiler operation. Most parts of the recovery boiler operation are common to boilers burning other fuels. The furnace operation differs significantly from operation of other boiler furnaces. Oxygen rich atmosphere is needed to burn fuel efficiently. But the main function of recovery boiler is to reduce spent cooking chemicals. Reduction reactions happen best in oxygen deficient atmosphere. This dual, conflicting nature of recovery furnace makes understanding it so challenging. To understand the processes happening in the recovery furnace one must try to understand the detailed processes that might occur and their limitations. Therefore chapters on materials, corrosion and fouling have been added.

Replacement of mechanically deboned chicken meat with its protein hydrolysate in mortadella-type sausages

Mortadella-type sausage manufactured using mechanically deboned chicken meat were reformulated replacing MDCM with increasing amounts of MDCM protein hydrolysates (10%, 20%, and 30%), and their physicochemical, microbiological, and sensorial characteristics were evaluated for 60 days of storage at 4 °C. The higher substitutions resulted in sausages more susceptible to lipid oxidation with higher TBARS values during storage; however, these values were lower than the organoleptic perception threshold. The sausages were darker and less red, with lower lightness (L*) and redness (a*) values than those of the control treatment. They had soft texture, which was evidenced by both the instrumental and sensory analysis. Therefore, the formulation containing 10% of MDCM protein hydrolysates proved to be the most suitable for mortadella-type sausage elaboration.