Obtenção e caracterização de suporte de regeneração óssea de dióxido de titânio

Due to complications caused by metallic implants in the replacement of bone tissue, the biological application of ceramics raised and became a viable alternative. The titania has the ability to promote bone tissue regeneration based on its structure, mechanical and biologically properties compatibility. The present work aims at obtaining and characterization of Titania (TiO2) porous ceramics produced by the polymeric sponge method (replica method). Polyurethane sponge with 10 ppi and 15 ppi (pores per linear inch) were used. The process differentiation is the air blower used to remove excess slurry. The ceramics sponges were dried in an oven, then pre-sintered at 1000 o C and sintered at 1450 o C. The effect of direct sintering at 1450 o C was also assessed. The percentage of solids used to prepare the slurry was 40 to 45% by weight. To increase the surface porosity of the sponge, 20% of starch was added. There was difficulty on controlling the thickness of the slurry layers on the sponge which resulted in the variation of samples mechanical resistance. Despite this, the results obtained are quite promising for the proposed use, indicating that it is possible to obtain titania sponges with an apparent porosity of around 60%, a bulk density ranging from 40 to 47% and a compressive strength resistance – that with better control of layers depositions – can vary from 1 to 4 MPa

Preparação e caracterização de vidros contendo nanopartículas de Ag

This work consists of preparation and characterization of glasses containing transition noble metals and the study of optical properties of such materials. The glasses were prepared by quenching of the glass melt followed by heat treatment and polishing of the monoliths. The structural characterization of glasses was made using differential thermal analysis, X-ray, Raman and infrared spectroscopies, while the optical properties were studied by UV-Vis and M-Lines spectroscopies. Preliminary results have shown that the color of the glasses is dependent on both concentration of silver and the melting temperature of the melt. Controlled heat treatments have been used to induce the crystallization of Ag nanoparticles within the glass. The study of crystallization was accompanied by electron microscopy and UV-Vis spectroscopy. Data from electron diffraction, as well as chemical analysis, EDX, were obtained using a transmission electron microscope. EDX data have shown that the atomic percentage of Ag is higher on the nanoparticle. X-ray diffraction was used in order to characterize the composition of the crystals and cubic AgCl was identified as the main crystallized nanophase obtained after annealing

Resistividade elétrica em aterro sanitário e relações com a produção de biogás

The landfill biogas can be an alternative energetic resource as a fuel to electrical energy generators, although, there are not too many techniques to prospect the gas. Usually, landfills receive home waste, which in most are constituted by organic matter whose degradation by anaerobic activity produces the biogas. Geophysics is an important tool in environmental studies and the electrorresistivity, an important method employed in contaminated areas by slurry or necroslurry, including a monitoring for each contaminator flow. The electrorresistivity has not too much application in finding biogas. For this work, two biogas drains in Rio Claro-SP landfill were selected: one whose waste disposition correspond to the initial activities in the landfill and another drain whose disposition started more recently. The result consists in a higher biogas production if compared to the biogas from the older drain. The present paper consists in a monitoring along one year, with dates collection in each fifteen days. These dates were tabled in Excel 2010 program and graphics of resistivity x depth were generated. Hereafter, most variable resistivity values depth were chosen, to further graphics pluviosity x resistivity generation in Grapher 8 program and the biogas output (m³/h) in monitoring period. The use of pluviosity parameter can be justified by its influence above resistivity. The results show that there is a horizon with possibly biogas accumulation. Lastly, the method was effective, although, for any application of geophysical methods, the knowledge about its limitations is necessary; in this case the influence of pluviosity and also that the measurements were made in one single point, it will not show any side variation

Preparação de substratos de carbeto de silício para fins aeroespaciais

This conclusion thesis has the objective of produce substrates of Silicon Carbide from the powder of SiC for aerospace use. The powder of SiC was pressed in cylindrical form by the process called “wet way”. For the inicial pressing process was used a uniaxial squeezer and after that was used a isostatic squeezer, after that the samples were synthesized. The next step was the machining and polishing to improve the features of the surface of the sample. Then the roughness was measured, as also the Arquimedes method and optical microscopy and scanning eletron microscopy. Some innovations were done, in one of the lots little vacancys were done with organic material or silicon to reduce the weight of the sample; and the other innovation were the use of a slip film of SiC on the surface of the sample, that were after synthesized with LASER to reduce the roughness, in this samples the roughness were reduce in 50 % if compared with the other samples

Redução de empeno em barra trefiladas do aço SAE 9254

In this paper we study the process of manufacture of wire drawn steel bars 9254, from rolled wire rod. These bars are used in the automotive industry for the manufacture of coil springs, which make up the system damping of several vehicles. The wire drawing process consists of the steps of pre-straightening, shot peening, drawing, cutting and polishing. The study aims to search for the configuration of process variables, which present the best result with respect to bending. To this were maintained settings prestraightening and mechanical stripping and varied angles and stringer polish being studied to replace the spinneret with a working angle, for a string with two working angles. To assist in the analysis of the results was the tool used DOE Software Minitab, which assesses the variation in results according to each parameter and the interaction parameters. It was thus possible to determine the best condition for wire drawing

Um estudo sobre a preparação metalográfica da liga de aluminio AA7075-T6

The increasing technological innovation and demand for materials with better properties boosts research into new materials and new alloys. To do so, aluminum alloys are being developed, among them the AA7075-T6, having many applications in aerospace and military industries, machinery and equipment, molds for plastic injection and structures. To study and understand the properties, characteristics and especially the microstructure of the material, the metallographic preparation is essential. This paper presents new methodologies to achieve the metallography of samples of scrap alloy AA7075-T6, with emphasis on methods of polishing. For the five samples, the best results were those with specific grinding, the samples only going down on the sander. For polishing, the most effective method so far has been using the polishing cloth 16.3, of ATM enterprise, solution of diamond 3 μm, solution of diamond 1 μm, and colloidal solution of OP-S. For the etching, the reactive agent used was phosphoric acid (H3PO4) 85% P.A., as 90% in the proportion of distilled water to 10% acid. The best results were obtained in the attacks of 300 and 240 seconds, revealing the grain boundaries in most areas. Methodologies need more studies and more tests, but the results have proved to be satisfactory

Condições mínimas para o encerramento de áreas que abrigaram resíduos sólidos domiciliares

In 2010 Brazil produced about 60.8 million of municipal solid waste, an amount 6.8% higher than in 2009 and six times the rate of urban population growth recorded in the same period. According to a study by the Brazilian Association of Companies of Special Wasteand Public Cleansing (Abrelpe), the average waste generated per person in the same period the country was 378 Kilograms, an amount 5.3% higher to 2009 (359 Kg). The total reached 60.8 milion tons of waste, 6.5 million tons were collected and not end up inrivers, streams and vacant lots. Of this total production, 42.4% or 22.9 million Tons, did not receive proper destination and destiny had dumps and landfills. The data show that the country is in upward trend in waste generation, but did not advance the appropriate destination at the same pace. The waste thus throw open cause public helth problems, such as proliferation of disease vectors (flies, mosquitoes, cockroaches, rats, and others). Generation of odors and especially the pollution of soil, surface water and groundwater through slurry ( liquid black, smelly and high pollution potential produced by the decomposition of organic matter contained in waste), affecting the water. This Study shows the popper closure of the areas, wich long has been degrading our natural resources, not to cause damage to nature and therefore society

Desenvolvimento de métodos analíticos para determinação de fósforo e selênio em amostras biológicas

A determinação de fósforo em amostras de rações e fezes de peixes por espectrometria no visível e de selênio em amostras vegetais de cultura orgânica por espectrometria de absorção atômica em forno de grafite (GFAAS) representa o foco principal do trabalho desenvolvido. O fósforo e o selênio são macro e micronutrientes importantes para a nutrição vegetal e animal, no entanto, se utilizados sem um controle adequado podem poluir o solo e os recursos hídricos, atingindo todo o meio ambiente. Dessa forma, foram desenvolvidos métodos para extração dos analitos que diminuíram significativamente os resíduos químicos produzidos nas determinações de rotina feitas na área de nutrição de plantas e de piscicultura. No caso do fósforo foram otimizados parâmetros físico-químicos para extração desse elemento por ultra-som e posterior quantificação por espectrofotometria no visível. No caso do selênio foram otimizados parâmetros físico-químicos para amostragem em suspensão (slurry) e determinação direta por GFAAS. Os principais parâmetros físico-químicos avaliados e otimizados foram: granulometria da amostra sólida, tempo e potência de sonificação, soluções extratoras, agentes surfactantes para estabilização do slurry; temperatura de pirólise e atomização, tipos de modificadores químicos e volume de amostragem nas determinações de selênio por GFAAS e tempo de reação e relação ao agente cromogênico/volume de amostra nas determinações espectrofotométricas de fósforo. O método de extração por ultra-som foi aplicado na determinação de fósforo biodisponível em amostras de rações de peixes e o método de amostragem em suspensão para a determinação de selênio em amostras de vegetais orgânicos

Efeito do Estrôncio (Sr) no tratamento de modificação do eutético da liga Al-1%Si

This study aimed to analyze the cooling curves, micro and macrograph alloy Al-1 %Si without the addition of strontium modifier and with the addition of the same. One of the ways of improving mechanical properties of alloy Al -Si is through the modification process. For the experiments two billets of the alloy Al-1%Si cast iron mold in a billet with addition of 0.02% strontium by weight, and the other billet without the addition of modifier were fused. In the solidification process of billet temperature was monitored and recorded every second for later plotting in Origin 8 program and analyzes the cooling curves obtained. The billets were cut and passed by grinding and polishing to perform the macrograph and micrographs. The results concerning the macrograph indicated that billet without the addition of Strontium particle size obtained was more refined than the billet where the strontium modifier was added. Regarding the micrograph, photos stemmed from the optical microscope didn´t show the expected modification effect by the addition of Strontium. This suggests that the low amount of silicon (1 %) present in the alloy used in this study interfered in the change process, because according to the literature review, Strontium 0.022 % by weight is sufficient to fully modify an alloy with 7% Silicon. The results from the cooling curve showed that both the eutectic temperature and the solidification time remained unchanged with the addition of strontium

Processo de esmerilhamento, polimento e caracterização de um Shear Plate

Shearplate is an optical glass plate having two flat surfaces and a small angle between them. The use of a high quality shear plate is essential to implement shear interferometric technique . The shear interferometry is a technique used to evaluate the light beam collimation. In order to guarantee the shearplate quality , the complete manufacturing process must be thoroughly monitored. In the manufacturing process, the first step consisted of the glass selection. The selected glass has been submitted to the process of cutting, gluing, chamfering, grinding and polishing. Each phase has been strictly monitored. The quality of the final result depends extremely on an appropriate starting condition, which arises from the grinding process, as the polishing process only recovers the brightness of the part, acting on a small scale on the wearing off of the part, as well as not changing the structured obtained in the grinding process. Respecting all stages of the manufacturing process, the quality of the part has evolved to a good result. The best result obtained showed PV distance of 162 nm, slightly less than λ / 4. This result is significant because the dimensions of the piece with respect to the dimensions of the polisher what interferes directly in the results. The closer are the dimensions of piece and the dimensions of the polisher, the greater the difficulty in controlling the propagation of errors

Estudos das condições da disposição final de resíduos sólidos domiciliares no aterro sanitário de Cachoeira Paulista – SP

In this assignment, will be assessed the conditions of operation for the final disposal of household solid waste landfill in the city of Cachoeira Paulista-SP. The theme chosen for research is of great social importance therefore is directly related to the well-being of the people, sustainable development, environmental protection and public health. Everyone should be aware of the problems related to improper final disposal of solid waste of any kind. The objectives of the study were: analyse the conditions of operation of the landfill; verify the treatment technology of percolating liquids (slurry) generated in the landfill; examine whether the landfill obey the rules; which cities in the region depend on the disposal system, verify that there are flaws in the final destination of solid waste in the municipality and in the cities of the region. The research is primarily a bibliographic review, obtained by querying the database and virtual libraries. Technical visits were also held at the study site, to check spot the methodology employed in the operation of landfill This work concluded that for the period under study, the landfill was as a landfill site, therefore, in accordance with the rules of operation

Análise do comportamento do desgaste de dressadores de ponta única confeccionados com diamantes naturais e sintético piramidais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo eletroquímico do sistema microestruturado montmorilonita-8- hidroxiquinolina na presença de íons metálicos

Pós-graduação em Química - IBILCE

Disponibilidade de fósforo em solo tratado com resíduos urbanos e industriais sob sistema de plantio direto cultivado com soja

Pós-graduação em Agronomia (Agricultura) - FCA

Avaliação de lagoas de lemnáceas no polimento de esgoto doméstico e produção de biomassa

Pós-graduação em Engenharia Civil - FEIS