Intensification of hemicellulose hot-water extraction from spruce wood by parameter tuning

The growing population on earth along with diminishing fossil deposits and the climate change debate calls out for a better utilization of renewable, bio-based materials. In a biorefinery perspective, the renewable biomass is converted into many different products such as fuels, chemicals, and materials, quite similar to the petroleum refinery industry. Since forests cover about one third of the land surface on earth, ligno-cellulosic biomass is the most abundant renewable resource available. The natural first step in a biorefinery is separation and isolation of the different compounds the biomass is comprised of. The major components in wood are cellulose, hemicellulose, and lignin, all of which can be made into various end-products. Today, focus normally lies on utilizing only one component, e.g., the cellulose in the Kraft pulping process. It would be highly desirable to utilize all the different compounds, both from an economical and environmental point of view. The separation process should therefore be optimized. Hemicelluloses can partly be extracted with hot-water prior to pulping. Depending in the severity of the extraction, the hemicelluloses are degraded to various degrees. In order to be able to choose from a variety of different end-products, the hemicelluloses should be as intact as possible after the extraction. The main focus of this work has been on preserving the hemicellulose molar mass throughout the extraction at a high yield by actively controlling the extraction pH at the high temperatures used. Since it has not been possible to measure pH during an extraction due to the high temperatures, the extraction pH has remained a “black box”. Therefore, a high-temperature in-line pH measuring system was developed, validated, and tested for hot-water wood extractions. One crucial step in the measurements is calibration, therefore extensive efforts was put on developing a reliable calibration procedure. Initial extractions with wood showed that the actual extraction pH was ~0.35 pH units higher than previously believed. The measuring system was also equipped with a controller connected to a pump. With this addition it was possible to control the extraction to any desired pH set point. When the pH dropped below the set point, the controller started pumping in alkali and by that the desired set point was maintained very accurately. Analyses of the extracted hemicelluloses showed that less hemicelluloses were extracted at higher pH but with a higher molar-mass. Monomer formation could, at a certain pH level, be completely inhibited. Increasing the temperature, but maintaining a specific pH set point, would speed up the extraction without degrading the molar-mass of the hemicelluloses and thereby intensifying the extraction. The diffusion of the dissolved hemicelluloses from the wood particle is a major part of the extraction process. Therefore, a particle size study ranging from 0.5 mm wood particles to industrial size wood chips was conducted to investigate the internal mass transfer of the hemicelluloses. Unsurprisingly, it showed that hemicelluloses were extracted faster from smaller wood particles than larger although it did not seem to have a substantial effect on the average molar mass of the extracted hemicelluloses. However, smaller particle sizes require more energy to manufacture and thus increases the economic cost. Since bark comprises 10 – 15 % of a tree, it is important to also consider it in a biorefinery concept. Spruce inner and outer bark was hot-water extracted separately to investigate the possibility to isolate the bark hemicelluloses. It was showed that the bark hemicelluloses comprised mostly of pectic material and differed considerably from the wood hemicelluloses. The bark hemicelluloses, or pectins, could be extracted at lower temperatures than the wood hemicelluloses. A chemical characterization, done separately on inner and outer bark, showed that inner bark contained over 10 % stilbene glucosides that could be extracted already at 100 °C with aqueous acetone.

Structural and functional Studies of angucycline tailoring enzymes

Polyketides are a diverse group of natural products produced in many bacteria, fungi and plants. These metabolites have diverse biological activities and several members of this group are in clinical use as antibiotics, anticancer agents, antifungals and immunosuppressants. The different polyketides are produced by polyketide synthases, which catalyze the condensation of extender units into various polyketide scaffolds. After the biosynthesis of the polyketide backbone, more versatility is created to the molecule by tailoring enzymes catalyzing for instance hydroxylations, methylations and glycosylations. Flavoprotein monooxygenases (FPMO) and short-chain alcohol dehydrogenases/reductases (SDR) are two enzyme families that catalyze unusual tailoring reactions in the biosynthesis of natural products. In the experimental section, functions of homologous FPMO and SDR tailoring enzymes from five different angucycline pathways were studied in vitro. The results revealed how different angucyclinones are produced from a common intermediate and that FPMO JadH and SDR LanV are responsible for the divergence of jadomycins and landomycins, respectively, from other angucyclines. Structural studies of these tailoring enzymes revealed differences between homologous enzymes and enabled the use of structure-based protein engineering. Mutagenesis experiments gave important information about the enzymes behind the evolution of distinct angucycline metabolites. These experiments revealed a correlation between the substrate inhibition and bi-functionality in JadH homologue PgaE. In the case of LanV, analysis of mutagenesis results revealed that the difference between the stereospecificities of LanV and its homologues CabV and UrdMred is unexpectedly related to the conformation of the substrate rather than to the structure of the enzyme. Altogether, the results presented here have improved our knowledge about different steps of angucycline biosynthesis and the reaction mechanisms used by the tailoring enzymes behind these steps. This information can hopefully be used to modify these enzymes to produce novel metabolites, which have new biological targets or possess novel modes-of-action. The understanding of these unusual enzyme mechanisms is also interesting to enzymologists outside the field of natural product research.

CCN2/CTGF silencing blocks cell aggregation in embryonal carcinoma P19 cell

Connective tissue growth factor (CCN2/CTGF) is a matricellular-secreted protein involved in extracellular matrix remodeling. The P19 cell line is an embryonic carcinoma line widely used as a cellular model for differentiation and migration studies. In the present study, we employed an exogenous source of CCN2 and small interference RNA to address the role of CCN2 in the P19 cell aggregation phenomenon. Our data showed that increasing CCN2 protein concentrations from 0.1 to 20 nM decreased the number of cell clusters and dramatically increased cluster size without changing proliferation or cell survival, suggesting that CCN2 induced aggregation. In addition, CCN2 specific silencing inhibited typical P19 cell aggregation, which could be partially rescued by 20 nM CCN2. The present study demonstrates that CCN2 is a key molecule for cell aggregation of embryonic P19 cells.

A phthalide derivative isolated from endophytic fungiPestalotiopsis photiniae induces G1 cell cycle arrest and apoptosis in human HeLa cells

MP [4-(3′,3′-dimethylallyloxy)-5-methyl-6-methoxyphthalide] was obtained from liquid culture of Pestalotiopsis photiniaeisolated from the Chinese Podocarpaceae plant Podocarpus macrophyllus. MP significantly inhibited the proliferation of HeLa tumor cell lines. After treatment with MP, characteristic apoptotic features such as DNA fragmentation and chromatin condensation were observed in DAPI-stained HeLa cells. Flow cytometry showed that MP induced G1 cell cycle arrest and apoptosis in a dose-dependent manner. Western blotting and real-time reverse transcription-polymerase chain reaction were used to investigate protein and mRNA expression. MP caused significant cell cycle arrest by upregulating the cyclin-dependent kinase inhibitor p27KIP1 protein and p21CIP1 mRNA levels in HeLa cells. The expression of p73 protein was increased after treatment with various MP concentrations. mRNA expression of the cell cycle-related genes, p21CIP1, p16INK4a and Gadd45α, was significantly upregulated and mRNA levels demonstrated significantly increased translation ofp73, JunB, FKHR, andBim. The results indicate that MP may be a potential treatment for cervical cancer.

Development of an alternative technology for the oyster mushroom production using liquid inoculum

Pleurotus ostreatus, worldwide known as oyster mushroom, was cultivated in banana straw using inocula produced by two different processes - liquid inoculum and the traditionally used solid inoculum. Different ratios (5, 10, 15, and 20%) were tested. Biological efficiency, yield, productivity, organic matter loss, and moisture of fruiting bodies as well as physical-chemical characteristics of banana straw were studied. Significant differences were observed for cellulose, lignin, and hemicellulose content between one and two harvests for both solid and liquid inocula. It was observed that P. ostreatus growth promoted higher degradation of lignin (80.36%), followed by hemicellulose (78.64%) and cellulose (60.37%). Significant differences between one and two harvests were also observed for the production parameters (biological efficiency and yield) for both kinds of inocula, liquid and solid. However, significant differences in productivity between harvests were observed only for solid inoculum.

Quality of minimally processed guava with different types of cut, sanification and packing

The purpose of this project was to evaluate the sanitization effect on the quality of minimally processed guava. Initially, research was carried out with consumers in a supermarket to verify preferences of packaging for guava. Following this, the guava cv. Paluma underwent two sanitization sequences using dehydrated sodium dichloroisocyanurate compound, in 50 ppm concentration, sanitization prior to (S1) and after (S2) being cut; removal of excess water; conditioning in PET packaging and PSPVC and storage at 3 ºC ± 1 ºC. Physicochemical analysis - [pH, total soluble solids (SST), total labeled acidity (ATT), ascorbic acid (AA), total sugars (AT) and reducers (AR)], textural sensorial and microbiological analyses were used to monitor the quality of the products. The consumers preferred the guava cut in halves with pulp and packed in PET, although this packaging promoted condensation of water vapor on the inner surface of the lid, compromising the appearance of the product. The two sanitization sequences and the two kinds of packaging did not significantly affect the pH, SST, ATT, SST/ATT, texture and AA values. The AT and AR tenors increased significantly in the MP guavas stored in the PSPVC package. Both sanitizations were efficient in the bacterial control of the indicators of the hygienicsanitary conditions, although the S1 sanitization proved to be more efficient in the control of autochthonous aerobic microbiota (aerobic mesophylic microorganisms). It can be concluded that guava cv. Paluma packed in PSPVC can be conserved for 6 days when stored at 3 ºC.

Survey of trace element and dietetic fiber composition of “Leblebi” which is a local snack food consumed in Turkey

Abstract In Turkey and several Middle East countries' people consume “leblebi” which is a traditional snack food made from chickpeas (Cicer arietinum L.). Chickpea products are highly nutritive and a cheap food for human consumption and have become an essential part of daily diets in the world. The present study aims to determine the chemical, nutritional and dietary composition of fifty leblebi samples marketed in Turkey. Protein values of the leblebi ranged from 19.4 to 23.9% dehulled and 20.3 to 20.8% for nondehulled leblebi while a value of 19.1% was recorded for chickpeas. Mineral results showed that Potassium (K) was the most abundant element in leblebi ranging from 6514 to 14431 mg/kg. The amount of dietary components neutral detergent fibre (NDF), acid detergent fibre (ADF), acid detergent lignin (ADL) and cellulose did not vary much between the samples analyzed.

Torrefioidun biohiilipelletin kirjallisuustutkimus ja koeajot pilottilaitoksessa

Tämä raportti käsittelee ”Torrefioidun biohiilipelletin laatu ja varastoitavuus” hankkeen tuloksia. Hankkeen tavoitteena oli tutkia torrefioidun biohiilipelletin prosessiteknologiaa, markkinoita ja tuotantokustannuksia kirjallisuustutkimusosiossa. Hankkeen päätutkimus keskittyi koeajoihin pilottilaitoksella, jossa valmistettiin biohiilipellettiä erilaisista puuraaka-aineista. Pilottilaitos oli perustettu Torrec Oy:n toimesta Etelä-Savon Energian Pursialan voimalaitoksen yhteyteen Mikkelissä ja sen tuotanto oli käynnistynyt kesällä 2014. Kaikki koe-erät valmistettiin vain käyttämällä sidonta-aineena lauhdevettä, jota oli tiivistynyt säiliön pohjalle torrefiointiprosessin aikana. Näin ollen erillistä lisäsidonta-aineita ei tarvittu, jolloin voidaan säästää tuotantokustannuksissa jatkossakin. Euroopan Unioni on asettanut 20 % tavoitteen uusiutuvien energioiden käytölle vuoteen 2020, josta biomassalla voidaan kattaa kaksi kolmannesta. Tutkimushankkeen tavoitteena oli metsään perustuvan bioenergiatuotannon lisääminen ja tuontienergian korvaaminen kotimaisella polttoaineella. Hankkeen tarkoituksena oli tutkimusanalyysien kautta kehittää uutta kilpailukykyistä teknologiavaihtoehtoa puupolttoaineiden hyödyntämiseksi. Torrefiointiteknologiaa ollaan kaupallistamassa ympäri Eurooppaa parasta aikaa ja uusia biohiilen tuotantolaitoksia on kehitteillä ja rakenteilla. Tutkimuksen tulokset osoittavat, että biohiilipelletillä on mahdollisuudet suurimittakaavaiseen energiantuotantoon laadun suhteen, kunhan sen käyttäminen tulee edullisemmaksi laitoksissa. Toisaalta, tämä kehitys vaatii tukimekanismeja valtion puolelta, jotta pelletit lähtisivät todella liikkeelle markkinoilla.

Utilizing hemicelluloses – the first step : controlled extraction with hot water

Människor utnyttjar ofta kemi mångsidigt i sitt vardagliga liv utan att närmare tänka på detaljerna. Nuförtiden kan man framställa en ökande mängd av produkter ur förnybara råmaterial och en av de mest mångsidiga nybara råmaterialet i Norden är barrträd. Den lyriska lägerelden eller spiselden och möbler av ved samt papper är en väsentlig del av vardagen. Också livsmedel och läkemedel kan innehålla föreningar ur ved. Ved som råmaterial består av tre huvudkomponenten: cellulosa, som är uppbyggd av druvsockermolekyler är en långkedjad, oförgrenad polymer; lignin, som sammanhåller fibrerna i vedmaterialet som lim samt hemicellulosor, som ofta är uppbyggda av olika sockerarter och är en förgrenad polymer. Följaktligen består vedmaterialet av 70 % socker. I detta arbete har vi koncentrerat på i hemicellulosa och dess extraktion ur gran, samt bestämning av hemicellulosans egenskaper. Den slutliga målsättningen i forskningen var att skapa nya produkter ur gran. Forskning i extraktionens hemligheter eller hur hemicellulosa kan effektivt extraheras i den önskade formen kräver nya typers experimentellasanläggningar och experiment samt matematisk modellering. Den långkedjade hemicellulosan är lämplig för att användas t.ex. i skyddshinnor eller i livsmedel. Medel- och småmolekylär hemicellulosa kan användas som utgångsämne för framställning av bränslen, smörjmedel, sockersyror och alkoholer, av vilka xylitol är mest känd för alla pga hälsobefrämjande effekter. Det är utomordentligt viktigt ur miljöns och energiekonomins synvinkel att sträva efter effektivering av utnyttjandet av den värdefullaste och största naturtillgången, skogen i vårt land, med alla möjliga sätt. Resultaten av denna forskning utnyttjar avsevärt den växande, nya, på skogen baserande biobaseradeindustrin, som framställer nya spetsprodukter samt skapar nya arbetsplatser. ----------------------------------------------------- Ihmiset hyödyntävät usein huomaamattaan kemiaa monipuolisesti jokapäiväisessä elämässä. Nykyään kasvava määrä tuotteista kyetään valmistamaan uusiutuvista raaka-aineista ja yksi monipuolisimmista uusiutuvista luonnonvaroistamme pohjolassa ovat havupuut. Tunnelmallinen nuotio tai takkatuli ja puiset huonekalut sekä paperi ovat olennainen osa arkea. Myös elintarvikkeet ja lääkkeet voivat sisältää puusta peräisin olevia yhdisteitä. Puu materiaalina koostuu rakenteeltaan pääosin kolmesta osasta; selluloosasta, joka on rypälesokerista koostuva pitkäketjuinen haaroittumaton polymeeri, ligniinistä, joka toimii puun koossa pitävänä liima-aineena ja hemiselluloosasta, joka on useista eri sokereista rakentunut haaroittunut polymeeri. Näin ollen puusta 70 % on sokeria. Tässä työssä olemme keskittyneet hemiselluloosaan ja sen uuttamiseen kuusesta, sekä ominaisuuksien kartoittamiseen. Tutkimusaiheen lopullinen tavoite on luoda uusia tuotteita kuusesta. Uuton salojen tutkiminen eli miten hemiselluloosa saadaan tehokkaasti uutettua halutunlaisena vaatii uudenlaisia koelaitteistoja ja kokeita, sekä matemaattista mallintamista. Suurikokoinen hemiselluloosa on sopivaa käytettäväksi esimerkiksi suojakalvoissa tai elintarvikkeissa. Keskikokoista ja pienimolekyylistä hemiselluloosaa voidaan käyttää lähtöaineena valmistettaessa polttoaineita, voiteluaineita, sokerihappoja ja sokerialkoholeja, joista xylitoli on terveysvaikutustensa vuoksi kaikille tuttu. Niin ympäristömme kuin myös energiataloutemme kannalta on ensiarvoisen tärkeää pyrkiä kaikin keinoin tehostamaan maallemme arvokkaan, sekä luonnonvaroistamme yhden suurimman, metsän, vastuullista hyödyntämistä. Tämän tutkimuksen tulokset hyödyntävät merkittävästi maahamme nousevaa uutta metsään pohjautuvaa biojalostusteollisuutta, joka valmistaa uusia huipputuotteita sekä luo työpaikkoja.

Chemical changes in biomass during torrefaction

Torrefaction is moderate thermal treatment (~200-300 °C) of biomass in an inert atmosphere. The torrefied fuel offers advantages to traditional biomass, such as higher heating value, reduced hydrophilic nature, increased its resistance to biological decay, and improved grindability. These factors could, for instance, lead to better handling and storage of biomass and increased use of biomass in pulverized combustors. In this work, we look at several aspects of changes in the biomass during torrefaction. We investigate the fate of carboxylic groups during torrefaction and its dependency to equilibrium moisture content. The changes in the wood components including carbohydrates, lignin, extractable materials and ashforming matters are also studied. And at last, the effect of K on torrefaction is investigated and then modeled. In biomass, carboxylic sites are partially responsible for its hydrophilic characteristic. These sites are degraded to varying extents during torrefaction. In this work, methylene blue sorption and potentiometric titration were applied to measure the concentration of carboxylic groups in torrefied spruce wood. The results from both methods were applicable and the values agreed well. A decrease in the equilibrium moisture content at different humidity was also measured for the torrefied wood samples, which is in good agreement with the decrease in carboxylic group contents. Thus, both methods offer a means of directly measuring the decomposition of carboxylic groups in biomass during torrefaction as a valuable parameter in evaluating the extent of torrefaction. This provides new information to the chemical changes occurring during torrefaction. The effect of torrefaction temperature on the chemistry of birch wood was investigated. The samples were from a pilot plant at Energy research Center of the Netherlands (ECN). And in that way they were representative of industrially produced samples. Sugar analysis was applied to analyze the hemicellulose and cellulose content during torrefaction. The results show a significant degradation of hemicellulose already at 240 °C, while cellulose degradation becomes significant above 270 °C torrefaction. Several methods including Klason lignin method, solid state NMR and Py-GC-MS analyses were applied to measure the changes in lignin during torrefaction. The changes in the ratio of phenyl, guaiacyl and syringyl units show that lignin degrades already at 240 °C to a small extent. To investigate the changes in the extractives from acetone extraction during torrefaction, gravimetric method, HP-SEC and GC-FID followed by GC-MS analysis were performed. The content of acetone-extractable material increases already at 240 °C torrefaction through the degradation of carbohydrate and lignin. The molecular weight of the acetone-extractable material decreases with increasing the torrefaction temperature. The formation of some valuable materials like syringaresinol or vanillin is also observed which is important from biorefinery perspective. To investigate the change in the chemical association of ash-forming elements in birch wood during torrefaction, chemical fractionation was performed on the original and torrefied birch samples. These results give a first understanding of the changes in the association of ashforming elements during torrefaction. The most significant changes can be seen in the distribution of calcium, magnesium and manganese, with some change in water solubility seen in potassium. These changes may in part be due to the destruction of carboxylic groups. In addition to some changes in water and acid solubility of phosphorous, a clear decrease in the concentration of both chlorine and sulfur was observed. This would be a significant additional benefit for the combustion of torrefied biomass. Another objective of this work is studying the impact of organically bound K, Na, Ca and Mn on mass loss of biomass during torrefaction. These elements were of interest because they have been shown to be catalytically active in solid fuels during pyrolysis and/or gasification. The biomasses were first acid washed to remove the ash-forming matters and then organic sites were doped with K, Na, Ca or Mn. The results show that K and Na bound to organic sites can significantly increase the mass loss during torrefaction. It is also seen that Mn bound to organic sites increases the mass loss and Ca addition does not influence the mass loss rate on torrefaction. This increase in mass loss during torrefaction with alkali addition is unlike what has been found in the case of pyrolysis where alkali addition resulted in a reduced mass loss. These results are important for the future operation of torrefaction plants, which will likely be designed to handle various biomasses with significantly different contents of K. The results imply that shorter retention times are possible for high K-containing biomasses. The mass loss of spruce wood with different content of K was modeled using a two-step reaction model based on four kinetic rate constants. The results show that it is possible to model the mass loss of spruce wood doped with different levels of K using the same activation energies but different pre-exponential factors for the rate constants. Three of the pre-exponential factors increased linearly with increasing K content, while one of the preexponential factors decreased with increasing K content. Therefore, a new torrefaction model was formulated using the hemicellulose and cellulose content and K content. The new torrefaction model was validated against the mass loss during the torrefaction of aspen, miscanthus, straw and bark. There is good agreement between the model and the experimental data for the other biomasses, except bark. For bark, the mass loss of acetone extractable material is also needed to be taken into account. The new model can describe the kinetics of mass loss during torrefaction of different types of biomass. This is important for considering fuel flexibility in torrefaction plants.

Mäntyöljyn tislauksen esikäsittely

Raakamäntyöljy on selluteollisuuden sivutuote. Suopa erotetaan mustalipeästä ja palstoitetaan tuottaen siten raakamäntyöljyä. Raakamäntyöljy tislataan tavanomaisesti viiteen pääjakeeseen: rasvahapot, hartsihapot, mäntyöljytisle, esiöljy ja mäntyöljypiki. Näiden jakeiden lisäksi raakamäntyöljyssä on erityisesti mustalipeästä siihen erottuneita epäpuhtauksia, jotka haittaavat raakamäntyöljyn prosessointia. Epäpuhtauksia ovat orgaaniset ja epäorgaaniset yhdisteet, kuten metallit, suolat ja ligniini. Nämä epäpuhtaudet aiheuttavat haitallisia reaktioita prosessissa huonontaen siten lopputuotejakeiden laatua. Tämän lisäksi epäpuhtaudet aiheuttavat saostumia prosessilaitteissa alentaen siten prosessointitehokkuutta. Raakamäntyöljyn esikäsittelyllä tehostetaan tislauksen toimintaa. Työssä esitetään esikäsittelymenetelmistä mm. degumming-menetelmä, laimea happopesu, hiilidioksidikäsittely, valkaisu ja lämpökäsittely. Menetelmien pohjalta valitaan tätä työtä varten yksi menetelmä, jonka pohjalta suunnitellaan kokeellisessa osassa suoritettavat kokeet. Kokeellinen osuus koostuu esikokeista, varsinaisista kokeista ja lisäkokeista. Menetelmän tarkoituksena on saavuttaa epäpuhtauksille 90–95 % reduktioaste. Kokeiden onnistumista tutkitaan analysoimalla alkuperäinen raakamäntyöljy, sekä jokaisen kokeen jälkeen erotetut faasit. Työssä saavutettiin hyvä erotustehokkuus. Alkuperäisen tavoitteen mukaista reduktioastetta ei pystytty määrittämään eri analyysimenetelmien ja niiden analyysituloksissa ilmenneiden eroavaisuuksien vuoksi, mutta lisäkokeiden ansiosta pystyttiin vahvistamaan kyseisen koejärjestelmän optimaalinen poistoaste. Lisäksi työssä havaittiin että esikäsittelytulos on hyvin riippuvainen käsiteltävän raaka-aineen koostumuksesta.

Hemiselluloosien talteenotto paineistetulla kuumavesiuutolla tuotetuista puu-uutteista

Puunjalostusteollisuus keskittyy tällä hetkellä lähinnä sellun ja paperin tuotantoon. Sellun tuotannossa käytetään puun komponenteista vain selluloosa. Puun muita pääkomponentteja ovat hemiselluloosa ja ligniini. Nämä yhdisteet ovat mahdollisia tulevaisuuden biomateriaalien lähtöaineita, mutta tähän mennessä ne on jätetty käyttämättä hyödyksi. Paineistettu kuumavesiuutto on menetelmä, jolla hemiselluloosat ja ligniinit olisi mahdollista erottaa puumateriaalista ennen sellunkeittoa, ja sen jälkeen fraktioida uutteesta erilleen jatkojalostusta varten. Fraktioinnista on tehty tutkimusta monella erilaisella menetelmällä ja eri menetelmiä yhdistelemällä. Tämä kandidaatin työ on kirjallinen työ, jossa käsitellään paineistettua kuumavesiuuttoa, sekä eri yksikköoperaatioita ja niiden mahdollisuuksia hemiselluloosan erotukseen puu-uutteista. Membraanisuodatus on menetelmä, jolla puu-uutteesta saadaan erotettua konsentroitu hemiselluloosafraktio. Membraanisuodatuksessa on kuitenkin puu-uutteiden tapauksessa havaittu ongelmia muun muassa kalvon likaantumisen kanssa. Yhdistämällä muutamia eri yksikköoperaatioita, saadaan parannettua membraanisuodatuksen tehoa, sekä hemiselluloosan puhtautta ja saantoa. Näitä mahdollisia yksikköoperaatioita ovat adsorptio, hapetus, saostus, kromatografiset menetelmät ja neste-nesteuutto.

Droplet Deposition in the Last Stage of Steam Turbine

During the expansion of steam in turbine, the steam crosses the saturation line and hence subsequent turbine stages run under wet condition. The stages under wet condition run with low efficiency as compared to stages running with supersaturated steam and the life of the last stage cascade is reduced due to erosion. After the steam crosses the saturation line it does not condense immediately but instead it becomes supersaturated which is a meta-stable state and reversion of equilibrium results in the formation of large number of small droplets in the range of 0.05 - 1 μm. Although these droplets are small enough to follow the stream lines of vapor however some of the fog droplets are deposited on the blade surface. After deposition they coagulate into films and rivulets which are then drawn towards the trailing edge of the blade due to viscous drag of the steam. These large droplets in the range of radius 100 μm are accelerated by steam until they impact on the next blade row causing erosion. The two phenomenon responsible for deposition are inertial impaction and turbulent-diffusion. This work shall discuss the deposition mechanism in steam turbine in detail and numerically model and validate with practical data.

An aryne route to aporphine alkaloids and related topics / |nIjaz Ahmad Chanda. -- 260 St. Catharines, Ont. : [s. n.],

This research was directed towards the investigation and development of an aryne route to the syntheses of aporphi ne and dibenzopyrrocolinium (dibenzoindolizinium) alkaloids and to the stability of the latter under the conditions used for aryne formation. The work c an be divided into three main sections . i) - Synthesis of Glaucine 6-Bromo-3,4-dimethoxyphenylacetic acid, prepared by the action of bromine i n acetic acid on3,4-dimethoxyphenylacetic a cid, was converted into its acid chloride by t he action of thionyl chloride. This on treatment with 3,4- dimethoxyphenylethylamine pr ovided N-(3, 4-dimethoxyphenylethyl)- 2-(2-bromo-4,S-dimethoxyphenyl)-acetamide which on dehydration with phosphoryl chloride (Bischler Napieralski reaction) in dry benzene afforded l -(2-bromo-4,S-dimethoxybenzyl)- 3,4-dihydro-6,7-dimethoxyisoquinoline, isolated as hydrochl oride. A new method o f destroying the excess of phosphoryl chloride was developed which proved to be quite useful. Methylation of the dihydroisoquinoline'with methyl iodide in methanol , and subsequent reduction with sodium borohydride provided (±)-6-bromolaudanosine. Act ion of potassamide or sodamide in anhydrous liquid ammonia on (±)-6-bromolaudanosine yielded the corresponding amino derivative along with other products. Diazotization and ring closure of (±)-6-aminolaudanosine then a f forded (±)-glaucine which was isolated as methiodide. ii) - Intramolecular Capture of Aryne During Glaucine Synthesis, and Subsequent Reactions . This section deals with the by-products formed under the conditions of the aryne stage of t he glaucine synthesis. The crude product, obtained in the reaction of potassamide or sodamide in liquid ammonia on (±)-6-bromolaudanosine, was s eparated by chromatography, Three products were separated and identified. a ) - 5,6-Dimethoxy-2-( 3,4-dimethoxy-6-ethylphenyl)-lmethylindole. Two mechanisms are proposed for the formation of this interesting product. This compound also was prepared by the action of potassamide in l,iquid ammonia on 5,6 ,l2,l2atetrahydro- 2,3,9,lO-tetramethoxy-7-methyldibenz[b,g]indolizinium i odide . b) - 5,6-Dimethoxy-2-(3,4-dimethoxy-6-vinylphenyl)-lmethylindoline. Its formation represented a new method of Hofmann degradation . Further confirmation of structure was done by performing the normal Hofmann reaction on 5, 6,12,12a-tetrahydro -2/3,9,lO-tetramethoxy ~7-methyldibe nz[ b,g]indolizinium iodide. The indoline prepared i n this way was identical in all respects with that prepared above . c) - 1- (2-amino-4,5-dimethoxybenzyl ) -l,2,3,4-tetrahydro-2- methyl-6,7-dimethoxyisoquinoline, was converted t o glaucine as stated in section 1 . iii) - Attempt:,ed Sxnthesis of Liriodenine Piperonal was converted into 3,4-methylenedioxyinitrostyrene which on reduction with lithium aluminium hydride provided 3,4-methylenedioxyphenylethylamine. The method of extraction after the reduction was improved t o some extent. The amine on condensation with m-chlorophenylacetyl chloride, prepared by the action of oxalyl chloride on 3,4-methylenedioxyphenylacetic acid, provided N-[ ~ -(3,4-methylenedioxyphenyl)- e thyl)-3-chlorophenylacetamide. This on dehydration with phosphoryl chloride in dry benzene followed by air oxidation afforded l-(3-chlorobenzoyl)-6,7-methylenedioxyi soquinoline. This compound on r eaction with potassamide in liquid ammonia afforded a crude product from which. one product was separated by chromatography i n a pure condition . This yellow compound analysed as,c17Hl ON2021 and was t he main product i n the reaction ; a t entative structure is proposed. A second compound, not obtained in pure condition, was submitted to Pschorr reaction in the hope of obtaining liriodenine, but without success.

Some aspects of the chemistry of Reissert compounds / |nDurga Prasad Aysola. -- 260 St. Catharines [Ont. : s. n.],

1-(0- and m-Ohlorobenzoyl)isoquinolines have been synthesized by two routes involving Reissert compounds. One route involves condensation of 2-benzoyl-l,2-dihydroisoquinaldonitrile with the appropriate chlorobenzaldehyde and the second involves rearrangement of the appropriate Z-(chlorobenzoyl)-l,Z-dihydroisoquinaldonitrile under basic conditions. The action of potassamide in anhydrous liquid ammonia on both ketones gave unexpectedly N-(l-isoquinolyl)benzamide (67) as the major product and the use of dibenzo-18-crown-6-ether 98% substantially improved the yd..e.ld in the case of l-chloroketone. This amide (67) exhibits unusual hydrogen bonding. 1-(o-chlorobenzoyl)-6,7-dimethoxyisoquinoline (79) was prepared in very s,amll quantities by the route involving condensation of 2-benzoyll, Z-dihydro-6,7-dimethoxyisoquinaldonitrile with o-chlorobenzaldehyde. The poor yields are due to the instability of the anion of 2-benzoyl1, Z-dihydro-6,7-dimethoxyisoquinaldonitrile. Attempted preparation of the ketone (79) by rearrangement of 2-(o-chlorobenzoyl)-l,2-dihydro6,7- dimethoxyisoquinaldonitrile under basic conditions yielded the start~ng material (Reissert compound) and 6,7-dimethoxyisoquinoline. The action of potassamide in anhydrous liquid ammonia on l-(o-bromo-4,5-dimethoxybenzoyl)isoquinoline (85), which was prepared by the route involving the condensation of 2-benzoyl-l,4-dihydroisoquinaldonitrile with o-bromo-4,5-dimethoxybenzaldehyde, gave two products, which have not yet been identified. The ketone (85) and its precursors are interest~ng in that their 20 eV and 70 eV mass spectra do not show molecular ions.