Multipacket reception in the presence of in-band full-duplex communication

In-Band Full-DupleX (IB-FDX) is defined as the ability for nodes to transmit and receive signals simultaneously on the same channel. Conventional digital wireless networks do not implement it, since a node’s own transmission signal causes interference to the signal it is trying to receive. However, recent studies attempt to overcome this obstacle, since it can potentially double the spectral efficiency of current wireless networks. Different mechanisms exist today that are able to reduce a significant part of the Self- Interference (SI), although specially tuned Medium Access Control (MAC) protocols are required to optimize its use. One of IB-FDX’s biggest problems is that the nodes’ interference range is extended, meaning the unusable space for other transmissions and receptions is broader. This dissertation proposes using MultiPacket Reception (MPR) to address this issue and adapts an already existing Single-Carrier with Frequency-Domain Equalization (SC-FDE) receiver to IB-FDX. The performance analysis suggests that MPR and IB-FDX have a strong synergy and are able to achieve higher data rates, when used together. Using analytical models, the optimal transmission patterns and transmission power were identified, which maximize the channel capacity with the minimal energy consumption. This was used to define a new MAC protocol, named Full-duplex Multipacket reception Medium Access Control (FM-MAC). FM-MAC was designed for a single-hop cellular infrastructure, where the Access Point (AP) and the terminals implement both IB-FDX and MPR. It divides the coverage range of the AP into a closer Full-DupleX (FDX) zone and a farther Half-DupleX (HDX) zone and adds a tunable fairness mechanism to avoid terminal starvation. Simulation results show that this protocol provides efficient support for both HDX and FDX terminals, maximizing its capacity when more FDX terminals are used.

Leptospirosis in animals and human contacts in Egypt: broad range surveillance

INTRODUCTION: Leptospirosis is a re-emerging zoonotic disease of humans and animals worldwide. The disease is caused by pathogenic species of the genus Leptospira. These organisms are maintained in nature via chronic renal infection of carrier animals, which excrete the organisms in their urine. Humans become infected through direct or indirect exposure to infected animals and their urine or through contact with contaminated water and soil. This study was conducted to investigate Leptospira infections as a re-emerging zoonosis that has been neglected in Egypt. METHODS: Samples from 1,250 animals (270 rats, 168 dogs, 625 cows, 26 buffaloes, 99 sheep, 14 horses, 26 donkeys and 22 camels), 175 human contacts and 45 water sources were collected from different governorates in Egypt. The samples were collected from different body sites and prepared for culture, PCR and the microscopic agglutination test (MAT). RESULTS: The isolation rates of Leptospira serovars were 6.9%, 11.3% and 1.1% for rats, dogs and cows, respectively, whereas the PCR results revealed respective detection rates of 24%, 11.3% and 1.1% for rats, dogs and cows. Neither the other examined animal species nor humans yielded positive results via these two techniques. Only six Leptospira serovars (Icterohaemorrhagiae, Pomona, Canicola, Grippotyphosa, Celledoni and Pyrogenes) could be isolated from rats, dogs and cows. Moreover, the seroprevalence of leptospiral antibodies among the examined humans determined using MAT was 49.7%. CONCLUSIONS: The obtained results revealed that rats, dogs and cows were the most important animal reservoirs for leptospirosis in Egypt, and the high seroprevalence among human contacts highlights the public health implications of this neglected zoonosis.

Epidemiological study of hepatitis B and C in a municipality with rural characteristics: Cássia dos Coqueiros, State of São Paulo, Brazil

Abstract: INTRODUCTION: Hepatitis B and C viral infections remain an important cause of global morbidity and mortality. Studies have been conducted in population groups of large cities, leaving gaps in the knowledge regarding the situation in small municipalities. We aimed to measure the prevalence of hepatitis B and C markers and presence of infection-associated factors. METHODS: All inhabitants of Cássia dos Coqueiros aged ≥18 years who agreed to participate in the research were included. We collected blood as well as information via a questionnaire between March 2011 and December 2013. Univariate and multivariate analyses were conducted. RESULTS: Among the 1,001 participants, 41 (4.1%) participants had a serological profile of hepatitis B viral exposure, and only one (0.1%) participant was considered a virus carrier. The frequency of isolated antibody to hepatitis B virus surface antigen (anti-HBs) markers was 17.8% for the overall population. In the multivariate analysis, hepatitis B virus (HBV) infection was associated with age, birth outside the State of São Paulo, history of hepatitis, ≥2 sexual partners in the last 6 months, and tattoos. Four (0.4%) participants had a serological profile of hepatitis C viral exposure. However, after confirmation using viral ribonucleic acid (RNA) evaluation, only one (0.1%) individual remained positive. CONCLUSIONS: The positivity rates for hepatitis B and C were low, despite greater sexual freedom and the recent emergence of illicit drugs, as observed by the health personnel working in Cássia dos Coqueiros.

Distribution of hepatitis B infection in Brazil: the epidemiological situation at the beginning of the 21 st century

Abstract Brazil was formerly considered a country with intermediate hepatitis B endemicity, with large heterogeneity between Brazilian regions and areas of high prevalence, especially in the Amazon basin. Systematic vaccination of children was initiated in 1998. Between 2004 and 2009, a large population-based study reported decreased prevalence in all regions of Brazil. This review analyzed the current hepatitis B epidemiological situation in Brazil through a systematic search of the scientific literature in MEDLINE, LILACS, and CAPES thesis database, as well as disease notifications to the Information System for Notifiable Diseases. The search strategy identified 87 articles and 13 theses, resulting in 100 total publications. The most recent results indicate reduced hepatitis B prevalence nationwide, classifying Brazil as having low endemicity. Most studies showed HBV carrier prevalence less than 1%. However, there are still isolated regions with increased prevalence, particularly the Amazon, as well as specific groups, such as homeless people in large cities and isolated Afro-descendant communities in the center of the country. This review alsao detected successful vaccination coverage reported in a few studies around the country. The prevalence of anti-HBs alone ranged from 50% to 90%. However, isolated and distant localities still have low coverage rates. This review reinforces the downward trend of hepatitis B prevalence in Brazil and the need to intensify vaccination strategies for young people and adults in specific regions with persisting higher HBV infection prevalence.

Cellulose-based composites as functional conductive materials for printed electronics

In this work, cellulose-based electro and ionic conductive composites were developed for application in cellulose based printed electronics. Electroconductive inks were successfully formulated for screen-printing using carbon fibers (CFs) and multi-walled carbon nanotubes (MWCNTs) as conductive functional material and cellulose derivatives working as binder. The formulated inks were used to fabricate conductive flexible and disposable electrodes on paper-based substrates. Interesting results were obtained after 10 printing passes and drying at RT of the ink with 10 % wt. of pristine CFs and 3% wt. of carboxymethyl cellulose (CMC), exhibiting a resistivity of 1.03 Ωcm and a resolution of 400 μm. Also, a resistivity of 0.57 Ωcm was obtained for only one printing pass using an ink based on 0.5 % wt. MWCNTs and 3 % wt. CMC. It was also demonstrated that ionic conductive cellulose matrix hydrogel can be used in electrolyte-gated transistors (EGTs). The electrolytes revealed a double layer capacitance of 12.10 μFcm-2 and ionic conductivity of 3.56x10-7 Scm-1. EGTs with a planar configuration, using sputtered GIZO as semiconducting layer, reached an ON/OFF ratio of 3.47x105, a VON of 0.2 V and a charge carrier mobility of 2.32 cm2V-1s-1.

Magnetotransport properties of metal/LaAlO3/SrTiO3 heterostructures

The quasi two-dimensional electron gas (q2DEG) hosted in the interface of an epitaxially grown lanthanum aluminate (LaAlO3) thin film with a TiO2-termi-nated strontium titanate (SrTiO3) substrate (001) has been massively studied in the last few years. The confinement of mobile electrons to within a few nanome-ters from the interface, superconductive behavior at low temperatures and elec-tron mobility exceeding 1000 cm2/(V.s) make this system an interesting candi-date to explore the physics of spin injection and transport. However, due to the critical thickness for conduction of 4 unit cells (uc) of LaAlO3, a high tunneling resistance hampers electrical access to the q2DEG, preventing proper injection of spin polarized current. Recently, our group found that depositing a thin overlayer of Co on LaAlO3 reduces the critical thickness, enabling conduction with only 1 uc of LaAlO3. Two scenarios arise to explain this phenomenon: a pinning of the Fermi level in the metal, inducing charge transfer in the SrTiO3; the creation of oxygen vacancies at the interface between LaAlO3 and the metal, leading to an n-type doping of the SrTiO3. In this dissertation, we will report on magnetotransport of metal/LaAlO3/SrTiO3 (metal: Ti, Ta, Co, Py, Au, Pt, Pd) heterostructures with 2 uc of LaAlO3 studied at low temperatures (2 K) and high magnetic fields (9 T). We have analyzed the transport properties of the gas, namely, the carrier concen-tration, mobility and magnetotransport regime and we will discuss the results in the light of the two scenarios mentioned above.

Aplicação do CRM no contexto do bloco operatório

RESUMO - Introdução: Na última década, inúmera literatura sobre temas de saúde, principalmente abordando a Segurança do Doente, foca a necessidade e a importância do conceito de trabalho em equipa e da sua implementação na atividade dos profissionais de saúde. É também referido, como exemplo a seguir, por analogia e com a devida adaptação, o conceito e a metodologia do Crew Resource Management (CRM) da aviação civil, em que vários autores reviram a evidência da sua aplicação à medicina e concluíram que era uma ferramenta útil em formação não-técnica para a prática da cirurgia segura. Porquê esta analogia entre a saúde e a aviação civil? Porquê este despertar na saúde para o trabalho em equipa e, principalmente, baseando-se na metodologia do CRM da aviação civil? Qual a importância da formação não-técnica e como pode esta ser adaptada à atividade dos profissionais da saúde, nomeadamente no bloco operatório? São estas as principais questões que irão ser investigadas e analisadas ao longo deste estudo. Objetivos: Na aviação civil, a segurança é uma das prioridades desta indústria e um dos pilares da sua sustentabilidade. Sendo a indústria da aviação civil, como a saúde, uma atividade complexa importa em primeiro lugar compreender como a segurança deve ser abordada nas organizações complexas. Depois de compreendermos os quatro pilares da segurança (política, risco, garantia e promoção) aplicados na aviação civil, analisaremos a necessidade da formação não-técnica, explicando a importância da metodologia do CRM na aviação civil e a possibilidade da “importação” dos seus conceitos pela saúde. Metodologia: Para aferirmos a necessidade de formação não-técnica pelos profissionais da saúde foi desenvolvido um inquérito aos alunos finalistas dos Cursos de Enfermagem e dos Cursos de Medicina e outro inquérito a profissionais da saúde, Enfermeiros e Médicos (Anestesista e Cirurgião) com funções no Bloco Operatório, para responderem às seguintes inquietações:  Tiveram os profissionais de saúde formação formal na sua licenciatura ou pós-graduação em temas sobre comunicação, trabalho em equipa, gestão do erro, gestão do stress, liderança, atitudes e comportamentos para um trabalho em equipa eficiente e seguro?  Tiveram formação inicial no início da sua carreira e formação recorrente equivalente sobre estes temas ao longo da sua carreira?  Estão os profissionais de saúde preparados, com conhecimentos obtidos em formação formal, para trabalhar em equipa? Pretendeu-se igualmente, através de inquérito, saber se os alunos finalistas das licenciaturas acima identificadas consideram importante para a sua futura atividade como profissionais de saúde possuírem competências não-técnicas para o trabalho em equipa para evitarem os eventos adversos. No referido inquérito será também questionado quais as matérias a abordar nas licenciaturas (ou em outra etapa da formação), consideradas necessárias para se obterem competências de trabalho em equipa e qual a opinião sobre a frequência da formação recorrente sobre estes temas. Conclusão: O trabalho ficará concluído com uma proposta de conteúdos programáticos para a formação não-técnica dos profissionais de saúde, para a sua formação inicial e para a formação recorrente ao longo da carreira, baseada na metodologia do CRM da aviação civil. Objetivo final: Como objetivo final do estudo pretende-se contribuir, através da aplicação de formação não-técnicas aos profissionais de saúde, para a melhoria da Segurança do Doente nos cuidados em saúde.

Al-doped ZnO ceramic sputtering targets based on nanocrystalline powders produced by emulsion detonation synthesis – deposition and application as a transparent conductive oxide material

Transparent conducting oxides (TCOs) have been largely used in the optoelectronic industry due to their singular combination of low electrical resistivity and high optical transmittance. They are usually deposited by magnetron sputtering systems being applied in several devices, specifically thin film solar cells (TFSCs). Sputtering targets are crucial components of the sputtering process, with many of the sputtered films properties dependent on the targets characteristics. The present thesis focuses on the development of high quality conductive Al-doped ZnO (AZO) ceramic sputtering targets based on nanostructured powders produced by emulsion detonation synthesis method (EDSM), and their application as a TCO. In this sense, the influence of several processing parameters was investigated from the targets raw-materials synthesis to the application of sputtered films in optoelectronic devices. The optimized manufactured AZO targets present a final density above 99 % with controlled grain size, an homogeneous microstructure with a well dispersed ZnAl2O4 spinel phase, and electrical resistivities of ~4 × 10-4 Ωcm independently on the Al-doping level among 0.5 and 2.0 wt. % Al2O3. Sintering conditions proved to have a great influence on the properties of the targets and their performance as a sputtering target. It was demonstrated that both deposition process and final properties of the films are related with the targets characteristics, which in turn depends on the initial powder properties. In parallel, the influence of several deposition parameters in the film´s properties sputtered from these targets was investigated. The sputtered AZO TCOs showed electrical properties at room temperature that are superior to simple oxides and comparable to a reference TCO – indium tin oxide (ITO), namely low electrical resistivity of 5.45 × 10-4 Ωcm, high carrier mobility (29.4 cm2V-1s-1), and high charge carrier concentration (3.97 × 1020 cm-3), and also average transmittance in the visible region > 80 %. These superior properties allowed their successful application in different optoelectronic devices.

Corporate governance failure at PT

The following case study depicts the bitter transfiguration of Portugal Telecom, SGPS (PT), a multinational telecommunications company that was once an honourable flag of innovation, corporate governance standards in Portugal and overseas. It scrutinises the controversial episodes that paved the way for the pitiful condition in which PT is nowadays: a company that carries the weight of a ruinous €897 million investment in a defaulted company and no more than a 25.6% stake in a heavily indebted Brazilian carrier. The free-fall is made, ironically, of a complete disregard for best corporate governance practices, allowing for PT’s major shareholders to take over the helm of the company, using it selfishly as a cash cow.

Contribution to drug discovery and development for tauopathies using yeast as a model

This work aimed to contribute to drug discovery and development (DDD) for tauopathies, while expanding our knowledge on this group of neurodegenerative disorders, including Alzheimer’s disease (AD). Using yeast, a recognized model for neurodegeneration studies, useful models were produced for the study of tau interaction with beta-amyloid (Aβ), both AD hallmark proteins. The characterization of these models suggests that these proteins co-localize and that Aβ1-42, which is toxic to yeast, is involved in tau40 phosphorylation (Ser396/404) via the GSK-3β yeast orthologue, whereas tau seems to facilitate Aβ1-42 oligomerization. The mapping of tau’s interactome in yeast, achieved with a tau toxicity enhancer screen using the yeast deletion collection, provided a novel framework, composed of 31 genes, to identify new mechanisms associated with tau pathology, as well as to identify new drug targets or biomarkers. This genomic screen also allowed to select the yeast strain mir1Δ-tau40 for development of a new GPSD2TM drug discovery screening system. A library of unique 138 marine bacteria extracts, obtained from the Mid-Atlantic Ridge hydrothermal vents, was screened with mir1Δ-tau40. Three extracts were identified as suppressors of tau toxicity and constitute good starting points for DDD programs. mir1Δ strain was sensitive to tau toxicity, relating tau pathology with mitochondrial function. SLC25A3, the human homologue of MIR1, codes for the mitochondrial phosphate carrier protein (PiC). Resorting to iRNA, SLC25A3 expression was silenced in human neuroglioma cells, as a first step towards the engineering of a neural model for replicating the results obtained in yeast. This model is essential to understand the mechanisms of tau toxicity at the mitochondrial level and to validate PiC as a relevant drug target. The set of DDD tools here presented will foster the development of innovative and efficacious therapies, urgently needed to cope with tau-related disorders of high human and social-economic impact.

Development and modulation of magnetic responsive supported ionic liquid membranes

The work presented in this thesis aims at developing a new separation process based on the application of supported magnetic ionic liquid membranes, SMILMs, using magnetic ionic liquids, MILs. MILs have attracted growing interest due to their ability to change their physicochemical characteristics when exposed to variable magnetic field conditions. The magnetic responsive behavior of MILs is thus expected to contribute for the development of more efficient separation processes, such as supported liquid membranes, where MILs may be used as a selective carrier. Driven by the MILs behavior, these membranes are expected to switch reversibly their permeability and selectivity by in situ and non-invasive adjustment of the conditions (e.g. intensity, direction vector and uniformity) of an external applied magnetic field. The development of these magnetic responsive membrane processes were anticipated by studies, performed along the first stage of this PhD work, aiming at getting a deep knowledge on the influence of magnetic field on MILs properties. The influence of the magnetic field on the molecular dynamics and structural rearrangement of MILs ionic network was assessed through a 1H-NMR technique. Through the 1H-NMR relaxometry analysis it was possible to estimate the self-diffusion profiles of two different model MILs, [Aliquat][FeCl4] and [P66614][FeCl4]. A comparative analysis was established between the behavior of magnetic and non-magnetic ionic liquids, MILs and ILs, to facilitate the perception of the magnetic field impact on MILs properties. In contrast to ILs, MILs show a specific relaxation mechanism, characterized by the magnetic dependence of their self-diffusion coefficients. MILs self-diffusion coefficients increased in the presence of magnetic field whereas ILs self-diffusion was not affected. In order to understand the reasons underlying the magnetic dependence of MILs self-diffusion, studies were performed to investigate the influence of the magnetic field on MILs’ viscosity. It was observed that the MIL´s viscosity decreases with the increase of the magnetic field, explaining the increase of MILs self-diffusion according to the modified Stokes- Einstein equation. Different gas and liquid transport studies were therefore performed aiming to determine the influence of the magnetic behavior of MILs on solute transport through SMILMs. Gas permeation studies were performed using pure CO2 andN2 gas streams and air, using a series of phosphonium cation based MILs, containing different paramagnetic anions. Transport studies were conducted in the presence and absence of magnetic field at a maximum intensity of 1.5T. The results revealed that gas permeability increased in the presence of the magnetic field, however, without affecting the membrane selectivity. The increase of gas permeability through SMILMs was related to the decrease of the MILs viscosity under magnetic field conditions.(...)

Perylene Diimide acceptors: Fabrication and characterization of electron-only, hole-only devices and solar cells

The thrust towards energy conservation and reduced environmental footprint has fueled intensive research for alternative low cost sources of renewable energy. Organic photovoltaic cells (OPVs), with their low fabrication costs, easy processing and flexibility, represent a possible viable alternative. Perylene diimides (PDIs) are promising electron-acceptor candidates for bulk heterojunction (BHJ) OPVs, as they combine higher absorption and stability with tunable material properties, such as solubility and position of the lowest unoccupied molecular orbital (LUMO) level. A prerequisite for trap free electron transport is for the LUMO to be located at a level deeper than 3.7 eV since electron trapping in organic semiconductors is universal and dominated by a trap level located at 3.6 eV. Although the mostly used fullerene acceptors in polymer:fullerene solar cells feature trap-free electron transport, low optical absorption of fullerene derivatives limits maximum attainable efficiency. In this thesis, we try to get a better understanding of the electronic properties of PDIs, with a focus on charge carrier transport characteristics and the effect of different processing conditions such as annealing temperature and top contact (cathode) material. We report on a commercially available PDI and three PDI derivatives as acceptor materials, and its blends with MEH-PPV (Poly[2-methoxy 5-(2-ethylhexyloxy)-1,4-phenylenevinylene]) and P3HT (Poly(3-hexylthiophene-2,5-diyl)) donor materials in single carrier devices (electron-only and hole-only) and in solar cells. Space-charge limited current measurements and modelling of temperature dependent J-V characteristics confirmed that the electron transport is essentially trap-free in such materials. Different blend ratios of P3HT:PDI-1 (1:1) and (1:3) show increase in the device performance with increasing PDI-1 ratio. Furthermore, thermal annealing of the devices have a significant effect in the solar cells that decreases open-circuit voltage (Voc) and fill factor FF, but increases short-circuit current (Jsc) and overall device performance. Morphological studies show that over-aggregation in traditional donor:PDI blend systems is still a big problem, which hinders charge carrier transport and performance in solar cells.

Frequency-domain receiver design for doubly-selective channels

This work is devoted to the broadband wireless transmission techniques, which are serious candidates to be implemented in future broadband wireless and cellular systems, aiming at providing high and reliable data transmission and concomitantly high mobility. In order to cope with doubly-selective channels, receiver structures based on OFDM and SC-FDE block transmission techniques, are proposed, which allow cost-effective implementations, using FFT-based signal processing. The first subject to be addressed is the impact of the number of multipath components, and the diversity order, on the asymptotic performance of OFDM and SC-FDE, in uncoded and for different channel coding schemes. The obtained results show that the number of relevant separable multipath components is a key element that influences the performance of OFDM and SC-FDE schemes. Then, the improved estimation and detection performance of OFDM-based broadcasting systems, is introduced employing SFN (Single Frequency Network) operation. An initial coarse channel is obtained with resort to low-power training sequences estimation, and an iterative receiver with joint detection and channel estimation is presented. The achieved results have shown very good performance, close to that with perfect channel estimation. The next topic is related to SFN systems, devoting special attention to time-distortion effects inherent to these networks. Typically, the SFN broadcast wireless systems employ OFDM schemes to cope with severely time-dispersive channels. However, frequency errors, due to CFO, compromises the orthogonality between subcarriers. As an alternative approach, the possibility of using SC-FDE schemes (characterized by reduced envelope fluctuations and higher robustness to carrier frequency errors) is evaluated, and a technique, employing joint CFO estimation and compensation over the severe time-distortion effects, is proposed. Finally, broadband mobile wireless systems, in which the relative motion between the transmitter and receiver induces Doppler shift which is different or each propagation path, is considered, depending on the angle of incidence of that path in relation to the direction of travel. This represents a severe impairment in wireless digital communications systems, since that multipath propagation combined with the Doppler effects, lead to drastic and unpredictable fluctuations of the envelope of the received signal, severely affecting the detection performance. The channel variations due this effect are very difficult to estimate and compensate. In this work we propose a set of SC-FDE iterative receivers implementing efficient estimation and tracking techniques. The performance results show that the proposed receivers have very good performance, even in the presence of significant Doppler spread between the different groups of multipath components.

A comparison analysis of the marketing strategy of Lufthansa and Emirates in Germany

The objective of this paper is to perform an analysis of the marketing strategy of Lufthansa and Emirates in Germany. Since both airlines use a similar approach to increase brand awareness an in-depth analysis is implemented in order to identify potential differences. Hereby, consumer insights about the perception and expectation travellers have in common will be analyzed and assessed with quantitative data. Both airlines are well positioned in terms of their marketing strategy, but when Emirates is strengthen its marketing campaign with that pace, the Gulf carrier will certainly make use of its economic strength and can become a frightening threat for the Lufthansa Group on long-haul destinations. Finally, recommendations for future marketing activities for both airlines will be given.

O contrato de transporte aéreo

The international conventions and agreements on civil liability emerged with the purpose of regulating the liability of the air carrier, bearing in mind two essential factors: i) the need to protect passengers interests, and ii) to ensure the continuous development of an incipient activity by limiting the compensation amounts. This research will focus on the analysis of the nature of the contract of air carriage, as well as the air carrier's liability regime regarding damages endured by passengers that may result from the non-performance of the contract.