On measurements of formation, growth, hygroscopicity, and volatility of atmospheric ultrafine particles

Atmospheric aerosol particles affect the global climate as well as human health. In this thesis, formation of nanometer sized atmospheric aerosol particles and their subsequent growth was observed to occur all around the world. Typical formation rate of 3 nm particles at varied from 0.01 to 10 cm-3s-1. One order of magnitude higher formation rates were detected in urban environment. Highest formation rates up to 105 cm-3s-1 were detected in coastal areas and in industrial pollution plumes. Subsequent growth rates varied from 0.01 to 20 nm h-1. Smallest growth rates were observed in polar areas and the largest in the polluted urban environment. This was probably due to competition between growth by condensation and loss by coagulation. Observed growth rates were used in the calculation of a proxy condensable vapour concentration and its source rate in vastly different environments from pristine Antarctica to polluted India. Estimated concentrations varied only 2 orders of magnitude, but the source rates for the vapours varied up to 4 orders of magnitude. Highest source rates were in New Delhi and lowest were in the Antarctica. Indirect methods were applied to study the growth of freshly formed particles in the atmosphere. Also a newly developed Water Condensation Particle Counter, TSI 3785, was found to be a potential candidate to detect water solubility and thus indirectly composition of atmospheric ultra-fine particles. Based on indirect methods, the relative roles of sulphuric acid, non-volatile material and coagulation were investigated in rural Melpitz, Germany. Condensation of non-volatile material explained 20-40% and sulphuric acid the most of the remaining growth up to a point, when nucleation mode reached 10 to 20 nm in diameter. Coagulation contributed typically less than 5%. Furthermore, hygroscopicity measurements were applied to detect the contribution of water soluble and insoluble components in Athens. During more polluted days, the water soluble components contributed more to the growth. During less anthropogenic influence, non-soluble compounds explained a larger fraction of the growth. In addition, long range transport to a measurement station in Finland in a relatively polluted air mass was found to affect the hygroscopicity of the particles. This aging could have implications to cloud formation far away from the pollution sources.

Observations on the first steps of atmospheric particle formation and growth

Atmospheric aerosol particles have a significant impact on air quality, human health and global climate. The climatic effects of secondary aerosol are currently among the largest uncertainties limiting the scientific understanding of future and past climate changes. To better estimate the climatic importance of secondary aerosol particles, detailed information on atmospheric particle formation mechanisms and the vapours forming the aerosol is required. In this thesis we studied these issues by applying novel instrumentation in a boreal forest to obtain direct information on the very first steps of atmospheric nucleation and particle growth. Additionally, we used detailed laboratory experiments and process modelling to determine condensational growth properties, such as saturation vapour pressures, of dicarboxylic acids, which are organic acids often found in atmospheric samples. Based on our studies, we came to four main conclusions: 1) In the boreal forest region, both sulphurous compounds and organics are needed for secondary particle formation, the previous contributing mainly to particle formation and latter to growth; 2) A persistent pool of molecular clusters, both neutral and charged, is present and participates in atmospheric nucleation processes in boreal forests; 3) Neutral particle formation seems to dominate over ion-mediated mechanisms, at least in the boreal forest boundary layer; 4) The subcooled liquid phase saturation vapour pressures of C3-C9 dicarboxylic acids are of the order of 1e-5 1e-3 Pa at atmospheric temperatures, indicating that a mixed pre-existing particulate phase is required for their condensation in atmospheric conditions. The work presented in this thesis gives tools to better quantify the aerosol source provided by secondary aerosol formation. The results are particularly useful when estimating, for instance, anthropogenic versus biogenic influences and the fractions of secondary aerosol formation explained by neutral or ion-mediated nucleation mechanisms, at least in environments where the average particle formation rates are of the order of some tens of particles per cubic centimeter or lower. However, as the factors driving secondary particle formation are likely to vary depending on the environment, measurements on atmospheric nucleation and particle growth are needed from around the world to be able to better describe the secondary particle formation, and assess its climatic effects on a global scale.

Hydrogen soil deposition and atmospheric variations in the boreal zone

This research has been prompted by an interest in the atmospheric processes of hydrogen. The sources and sinks of hydrogen are important to know, particularly if hydrogen becomes more common as a replacement for fossil fuel in combustion. Hydrogen deposition velocities (vd) were estimated by applying chamber measurements, a radon tracer method and a two-dimensional model. These three approaches were compared with each other to discover the factors affecting the soil uptake rate. A static-closed chamber technique was introduced to determine the hydrogen deposition velocity values in an urban park in Helsinki, and at a rural site at Loppi. A three-day chamber campaign to carry out soil uptake estimation was held at a remote site at Pallas in 2007 and 2008. The atmospheric mixing ratio of molecular hydrogen has also been measured by a continuous method in Helsinki in 2007 - 2008 and at Pallas from 2006 onwards. The mean vd values measured in the chamber experiments in Helsinki and Loppi were between 0.0 and 0.7 mm s-1. The ranges of the results with the radon tracer method and the two-dimensional model were 0.13 - 0.93 mm s-1 and 0.12 - 0.61 mm s-1, respectively, in Helsinki. The vd values in the three-day campaign at Pallas were 0.06 - 0.52 mm s-1 (chamber) and 0.18 - 0.52 mm s-1 (radon tracer method and two-dimensional model). At Kumpula, the radon tracer method and the chamber measurements produced higher vd values than the two-dimensional model. The results of all three methods were close to each other between November and April, except for the chamber results from January to March, while the soil was frozen. The hydrogen deposition velocity values of all three methods were compared with one-week cumulative rain sums. Precipitation increases the soil moisture, which decreases the soil uptake rate. The measurements made in snow seasons showed that a thick snow layer also hindered gas diffusion, lowering the vd values. The H2 vd values were compared to the snow depth. A decaying exponential fit was obtained as a result. During a prolonged drought in summer 2006, soil moisture values were lower than in other summer months between 2005 and 2008. Such conditions were prevailing in summer 2006 when high chamber vd values were measured. The mixing ratio of molecular hydrogen has a seasonal variation. The lowest atmospheric mixing ratios were found in the late autumn when high deposition velocity values were still being measured. The carbon monoxide (CO) mixing ratio was also measured. Hydrogen and carbon monoxide are highly correlated in an urban environment, due to the emissions originating from traffic. After correction for the soil deposition of H2, the slope was 0.49±0.07 ppb (H2) / ppb (CO). Using the corrected hydrogen-to-carbon-monoxide ratio, the total hydrogen load emitted by Helsinki traffic in 2007 was 261 t (H2) a-1. Hydrogen, methane and carbon monoxide are connected with each other through the atmospheric methane oxidation process, in which formaldehyde is produced as an important intermediate. The photochemical degradation of formaldehyde produces hydrogen and carbon monoxide as end products. Examination of back-trajectories revealed long-range transportation of carbon monoxide and methane. The trajectories can be grouped by applying cluster and source analysis methods. Thus natural and anthropogenic emission sources can be separated by analyzing trajectory clusters.

Diverse bodies-space politics: Towards a critique of social (in)justice of built environment

Writing has long played an important role in the progression of architecture and the built environment. Histories of architecture are written, manifestoes that form the basis for a designer’s work are written and most importantly, the built environment advances itself through the act of critical writing. Not unlike the visual arts, literature and poetry, the tradition of written criticism has been crucial to the progression of architecture and its allied professions (Franz 2003). This article contributes to architecture and the built environment through the act of a written essay that critiques the problem of bodily diversity to architecture. In particular, the article explores the implications of body-space politics and abstracted body thinking on diverse bodies and their spatial justice. Using Soja’s Spatial Justice theory (2008), we seek to point out the underlying conceptions and power differentials assigned to different bodies spatially and how this leads to spatial injustices and contested spaces. The article also critically analyses the historical emergence of ‘the standardised body’ in architecture and its application in design theory and practice , and looks at how bodies often found on the outside of architecture highlight how such thinking creates in justices. Different theories are drawn on to help point to how design through the use of the upright, forward facing, male bod willingly and unwillingly denies access to resources and spatialities of everyday life. We also suggest ways to re-conceptualise the body in design practice and teaching.

Investigating the interactions of road users and pedestrians in a dynamic rail level crossing environment

There are 23,500 level crossings in Australia. In these types of environments it is important to understand what human factor issues are present and how road users and pedestrians engage with crossings. A series of on-site observations were performed over a 2-day period at a 3-track active crossing. This was followed by 52 interviews with local business owners and members of the public. Data were captured using a manual-coding scheme for recording and categorising violations. Over 700 separate road user and pedestrian violations were recorded, with representations in multiple categories. Time stamping revealed that the crossing was active for 59% of the time in some morning periods. Further, trains could take up to 4-min to arrive following its first activation. Many pedestrians jaywalked under side rails and around active boom gates. In numerous cases pedestrians put themselves at risk in order to beat or catch the approaching train, ignored signs to stop walking when the lights were flashing. Analysis of interview data identified themes associated with congestion, safety, and violations. This work offers insight into context specific issues associated with active level crossing protection.

Finnish and Austrian Wood Markets in a Changing Environment

At present the operating environment of sawmills in Europe is changing and there are uncertainties related in raw material supply in many countries. The changes in the operating environment of roundwood markets and the effects followed by these changes have brought up several interesting issues from the viewpoint of research. Lately new factors have been influencing the roundwood markets, such as increasing interest towards wood-based energy and implementation of new energy policies as well as changes in wood trade flows that affect the domestic markets in many countries. This Master’s thesis studies the adaptation ability of Finnish roundwood markets in a changing operating environment, aiming to produce an up-to-date analysis considering new development trends. The study concentrates on the roundwood markets from the viewpoint of sawmill industry since the industry is dependent on the functioning of the markets and sawmills are highly affected by the changes on the roundwood markets. To facilitate international comparison, the study is implemented by comparing Finnish and Austrian roundwood markets and analysing changes happening in the two countries. Finland and Austria share rather similar characteristics in the roundwood market structures, forest resources and forest ownership as well as production of roundwood and sawnwood. In addition they both are big exporters of forest industry products. In this study changes in the operating environment of sawmill industry both in Finland as well as in Austria are compared to each other aiming to recognise the main similarities and differences between the countries. In addition both development possibilities as well as challenges followed by the changes are discussed. The aim of the study is to define the main challenges and possibilities confronted by the actors on the markets and also to find new perspectives to approach these. The study is implemented as a qualitative study. The theoretical framework of the study describes the operating environment of wood markets from the viewpoint of the sawmill industry and represents the effects of supply and demand on the wood markets. The primary research material of the study was gathered by interviewing high level experts of forestry and sawmill industry in both Finland and Austria. The aim was to receive as extensive country specific viewpoint from the markets as possible, hence interviewees represented different parties of the markets. After creating country-specific profiles based on the theoretical framework a cross-country comparison was implemented. As a consequence the main similarities and differences in the operating environment and on the roundwood markets of Finland and Austria were recognized. In addition the main challenges and possibilites were identified. The results of the study offer a wide analysis regarding the main similarities and differences of the wood markets of Finland and Austria and their operating environments as well as concerning challenges and possibilities faced on the markets.

Adhesion,Presence and Antifouling of Deinococcus geothermalis in Paper Machine Environment

This thesis has two items: biofouling and antifouling in paper industry. Biofouling means unwanted microbial accumulation on surfaces causing e.g. disturbances in industrial processes, contamination of medical devices or of water distribution networks. Antifouling focuses on preventing accumulation of the biofilms in undesired places. Deinococcus geothermalis is a pink-pigmented, thermophilic bacterium, and extremely resistant towards radiation, UV-light and desiccation and known as a biofouler of paper machines forming firm and biocide resistant biofilms on the stainless steel surfaces. The compact structure of biofilm microcolonies of D. geothermalis E50051 and the adhesion into abiotic surfaces were investigated by confocal laser scanning microscope combined with carbohydrate specific fluorescently labelled lectins. The extracellular polymeric substance in D. geothermalis microcolonies was found to be a composite of at least five different glycoconjugates contributing to adhesion, functioning as structural elements, putative storages for water, gliding motility and likely also to protection. The adhesion threads that D. geothermalis seems to use to adhere on an abiotic surface and to anchor itself to the neighbouring cells were shown to be protein. Four protein components of type IV pilin were identified. In addition, the lectin staining showed that the adhesion threads were covered with galactose containing glycoconjugates. The threads were not exposed on planktic cells indicating their primary role in adhesion and in biofilm formation. I investigated by quantitative real-time PCR the presence of D. geothermalis in biofilms, deposits, process waters and paper end products from 24 paper and board mills. The primers designed for doing this were targeted to the 16S rRNA gene of D. geothermalis. We found D. geothermalis DNA from 9 machines, in total 16 samples of the 120 mill samples searched for. The total bacterial content varied in those samples between 107 to 3 ×1010 16S rRNA gene copies g-1. The proportion of D. geothermalis in those same samples was minor, 0.03 1.3 % of the total bacterial content. Nevertheless D. geothermalis may endanger paper quality as its DNA was shown in an end product. As an antifouling method towards biofilms we studied the electrochemical polarization. Two novel instruments were designed for this work. The double biofilm analyzer was designed for search for a polarization program that would eradicate D. geothermalis biofilm or from stainless steel under conditions simulating paper mill environment. The Radbox instrument was designed to study the generation of reactive oxygen species during the polarization that was effective in antifouling of D. geothermalis. We found that cathodic character and a pulsed mode of polarization were required to achieve detaching D. geothermalis biofilm from stainless steel. We also found that the efficiency of polarization was good on submerged, and poor on splash area biofilms. By adding oxidative biocides, bromochloro-5,5-dimethylhydantoin, 2,2-dibromo-2-cyanodiacetamide or peracetic acid gave additive value with polarization, being active on splash area biofilms. We showed that the cathodically weighted pulsed polarization that was active in removing D. geothermalis was also effective in generation of reactive oxygen species. It is possible that the antifouling effect relied on the generation of ROS on the polarized steel surfaces. Antifouling method successful towards D. geothermalis that is a tenacious biofouler and possesses a high tolerance to oxidative stressors could be functional also towards other biofoulers and applicable in wet industrial processes elsewhere.

The watershed simulation and forecasting system in the National Board of and the Environment

Yhteenveto: Vesistömalleihin perustuva vesistöjen seuranta- ja ennustejärjestelmä vesi- ja ympäristöhallinnossa

Ways of Explaining Workplace Bullying: A Review of Enabling, Motivating, and Precipitating Structures and Processes in the Work Environment

This paper summarizes literature explaining workplace bullying and focuses on organisational antecedents of bullying. In order to better understand the logic behind bullying, a model discussing different types of explanations is put forward. Thus, explanations for and factors associated with bullying are classified into three groups, i.e. enabling structures or necessary antecedents (e.g. perceived power imbalances, low perceived costs, and dissatisfaction and frustration), motivating structures or incentives (e.g. internal competition, reward systems, and expected benefits), and precipitating processes or triggering circumstances (e.g. downsizing and restructuring, organisational changes, changes in the composition of the workgroup). The paper concludes that bullying is often an interaction between structures and processes from all three groupings.

Probing Fluorine Interactions in a Polyhydroxylated Environment: Conservation of a C-F center dot center dot center dot H-C Recognition Motif in Presence of O-H center dot center dot center dot O Hydrogen Bonds

Three conformationally locked fluorinated polycyclitols have been specially crafted on a rigid trans-decalin backbone, employing a surprisingly facile pyridine-poly(hydrogen fluoride)-mediated stereospecific epoxide ring opening as the key reaction. Molecula design of the three fluorinated probes under study focused on providing an efficient platform for (a) evaluating the ability of covalently bonded fluorine, vis-a-vis the isosteric hydroxy group, to act as a H-bond acceptor and (b) examining the possibility for an organic fluorine moiety, placed suitably in a spatially invariant position, to engage an 1,3-diaxial OH functionality in a purported intramolecular O-H center dot center dot center dot F hydrogen bond. The present endeavour reveals that C(sp(3))-F center dot center dot center dot H-C(sp(3)) hydrogen bonds, though weak and lesser investigated, can indeed be observed and supramolecular recognition motifs, involving such interactions, can be conserved even in crystal structures laden with stronger O-H center dot center dot center dot O hydrogen bonds.

Role of the environment in the interaction of nonintercalators with Z-DNA

Interaction of the DNA binding nonintercalators Netropsin, Distamycin and the mPD derivative with Z-DNA has been studied. It has been found that environmental factors like the solvent and added cations significantly modulate the interaction of these ligands with Z-DNA. However no definite Z to B transition in presence of these ligands was found in any case, in contrast to previously reported results (Ch. Zimmer, C. Marck and W. Guschlbauer, FEBS Lett. 154, 156-160 (1983)).

An environment-friendly Beckmann rearrangement: the diazotisation of ketoxime carbamates

The titled reaction was effected with iso-amyl nitrite or sodium nitrite, both in cone. H2SO4 at 0-25 degrees C in excellent yields (55-98%). Apart from the mild temperatures employed, organic solvents and reagents can be avoided, and the by-products are CO2 and N-2, so the conditions are environment-friendly. (C) 2000 Elsevier Science Ltd. All rights reserved.