Ethanol oxidation reactions using SnO(2)@Pt/C as an electrocatalyst

This paper presents a study on the ethanol oxidation reaction using SnO(2)@Pt/C core-shell structures as electrocatalysts. All the materials used, including Pt/C and PtSn/C E-tek, were 20% (w/w) metal on carbon. The formation of core-shell nanoparticles (SnO(2)@Pt/C) was measured by UV-vis spectrophotometry. X-ray diffraction measurements showed Pt (shell) diffraction patterns without influence from the SnO(2) core and without any shift in 2 theta values for Pt. The diameters of the core-shell particle structures, measured using high-resolution transmission electron microscopy images, were in the range of 3-16 nm. The electrochemical profile for SnO(2)@Pt/C in an acidic medium (H(2)SO(4) at a concentration of 0.5 mol L(-1)) was almost the same as the typical electrochemical behavior for Pt in an acidic medium. Furthermore, the onset potential for the ethanol oxidation reaction using SnO(2)@Pt/C was almost the same as that for PtSn/C E-tek (0.23 V versus the reversible hydrogen electrode). However, the mass current peak densities for ethanol oxidation were 50% higher on SnO(2)@Pt/C than on PtSn/C E-tek. In the polarization curve, the mass current density for ethanol oxidation was higher at all potentials for SnO(2)@Pt/C when compared to Pt/C and PtSn/C E-tek. At 0.5 V, the current mass density for ethanol oxidation on SnO(2)@Pt was 2.3 times of that for the same process on the commercial material. The electrocatalytic activity of SnO(2)@Pt/C for ethanol oxidation was associated with an increase in the electrochemically active surface area. However, an electronic effect should also be considered because the Pt shell changes its electronic structure in the presence of the foreign core. (C) 2010 Elsevier B.V. All rights reserved.

Methane conversion reactions on Ni catalysts promoted with Rh: Influence of support

Ni catalysts supported on gamma-Al(2)O(3) and Mg(Al)O were prepared with and without Rh as a promoter and tested in the reforming of methane in the presence of excess methane, simulating a model biogas. The effects of adding synthetic air on the methane conversion and the formation of carbon were assessed. The catalysts were characterized by X-ray spectroscopy (EDS), surface area (BET), X-ray diffraction (XRD), Temperature-programmed reduction (TPR), X-ray absorption near-edge structure (XANES) and XPD. The results showed that in catalysts without Rh, the Ni interacts strongly with the supports, showing high reduction temperatures in TPR tests. The addition of Rh increased the amount of reducible Ni and facilitated the reduction of the species interacting strongly with the support. In the catalytic tests, the samples promoted with Rh suffered higher carbon deposition. The in situ XPD suggested that on the support gamma-Al(2)O(3), the presence of Rh probably led to a segregation of Ni species with time on stream, leading to carbon deposition. On the support MgAlO, the presence of Rh improved the dispersion of Ni, by reducing the Ni(0) crystallite size, suggesting that in this case the carbon deposition was due to a favoring of CH(4) decomposition by Rh. (C) 2011 Elsevier B.V. All rights reserved.

Speak Good English Movement in Singapore : Reactions in Social and Traditional Media

The first Speak Good English Movement, SGEM, took place in 2000, and has been organized annually ever since. Speaking a “standard” form of English is considered to bring increased personal power. However, the SGEM wants the Singaporeans to use “standard” English in their private life as well. A decade after the beginning of the campaign, a Speak Good Singlish Movement was started. Based on studies of language and identity, it is understandable why some Singaporeans might feel the SGEM threatens their identity. However, the reactions towards the campaign are mainly positive. For the purposes of this analysis, Twitter messages, Facebook pages, and newspaper articles from The Straits Times were collected. The SGEM has hailed both direct and indirect praise and criticism in both social and traditional media: Five newspaper articles praise the campaign while five criticize it; the results are nine and seven respectively for social media. This thesis looks at reactions towards the SGEM in both social and traditional media, analyzes how these reactions might relate to the ideas of the power of language, its variety and the relation of language and identity.

A study of slag corrosion of oxides and oxide-carbon refractories during steel refining

The use of ceramic material as refractories in the manufacturing industry is a common practice worldwide. During usage, for example in the production of steel, these materials do experience severe working conditions including high temperatures, low pressures and corrosive environments. This results in lowered service lives and high consumptions of these materials. This, in turn, affects the productivity of the whole steel plant and thereby the cost. In order to investigate how the service life can be improved, studies have been carried out for refractories used in the inner lining of the steel ladles. More specifically, from the slag zone, where the corrosion is most severe. By combining thermodynamic simulations, plant trails and post-mortem studies of the refractories after service, vital information about the behaviour of the slagline refractories during steel refining and the causes of the accelerated wear in this ladle area has been achieved. The results from these studies show that the wear of the slagline refractories of the ladle is initiated at the preheating station, through reduction-oxidation reactions. The degree of the decarburization process is mostly dependent on the preheating fuel or the environment. For refractories without antioxidants, refractory decarburization is slower when coal gas is used in ladle preheating than when a mixture of oil and air is used. In addition, ladle preheating of the refractories without antioxidants leads to direct wear of the slagline refractories. This is due to the total loss of the matrix strength, which results in a sand-like product. Thermal chemical changes that take place in the slagline refractories are due to the MgO-C reaction as well as the formation of liquid phases from impurity oxides. In addition, the decrease in the system pressure during steel refining makes the MgO-C reaction take place at the steel refining temperatures. This reduces the refractory’s resistance to corrosion. This is a serious problem for both the magnesia-carbon and dolomite-carbon refractories. The studies of the reactions between the slagline refractories and the different slag compositions showed that slags rich in iron oxide lead mostly to the oxidation of carbon/graphite in the carbon-containing refractories. This leads to an increased porosity and wettability and therefore an enhanced penetration of slag into the refractory structure. If the slag contains high contents of alumina and or silica (such as the steel refining slag), reactions between the slag components and the dolomite-carbon refractory are promoted. This leads to the formation of low-temperature melting phases such as calcium-aluminates and silicates. The state of these reaction products during steel refining leads to an accelerated wear of the dolomite-carbon refractory. The main products of the reactions between the magnesia-carbon refractory and the steel refining slag are MgAl2O4 spinels, and calcium-aluminates, and silicates. Due to the good refractory properties of MgAl2O4 spinels, the slag corrosion resistance of the magnesiacarbon refractory is promoted.

Reactions of Persons with Dementia to Caregivers Singing in Morning Care Situations

Music therapeutic caregiving', when caregivers sing for or together with persons with severe dementia during care situations, has been suggested as a way to reduce problematic behaviors in dementia care. The present study implemented this technique as an intervention in dementia care. Six caregivers participated in group interviews about their experiences of morning care situations without and with'Music therapeutic caregiving'. Through a qualitative content analysis two themes emerged.'Being in a different reality' was based on'usual' morning care situations. The caregivers' experienced the persons with dementia as absent-minded; communication and cooperation were difficult. The second theme,'Being present', was based on morning care situations with the intervention. The caregivers described communication as enhanced; the persons with dementia expressed themselves more appropriately, making cooperation possible. The results indicate that'Music therapeutic caregiving' might lead to a more positive experience of the person with dementia and seems to increase receptivity to caregiving.  

Crown ethers : applications in inorganic synthesis

The ability of macroheterocyclic compounds to complex with ionic species has led to the synthesis and investigation of many multidentate macroheterocyclic species. The most stable complexes are formed between macrocyclic polyetheral ligands (crown ethers) with alkali or alkaline earth metal iona. There is an excellent correlation of the stability of these complexes with the size of the cation and the site of the cavity in the macrocyclic ligand. Additional factors, such as the basicity of the ligand and the solvating ability of the solvent, also play important roles in the stabilization of the complex. The stability of such complexes has been advantageously used to increase anionic reactivity and has been successfully applied to several organic fluorinations, oxidations, and similar reactions. The use of macrocyclic ligands in inorganic syntheses of otherwise difficult to obtain fluoro compounds has not been reported. O-carborane and m-carborane, C2BlOHl2, are icosahedral cage systems derived from Bl2H122- by replacement of BH with the isoelectronic CH group. These stable molecules exhibit electron-deficient bonding which can best be explained by delocalization of electrons. This delocalization gives rise to stability similar to that found in aromatic hydrocarbons. Crown ether activated potassium fluoride has been successfully employed in the conversion of alkyl, acyl and aryl halides to their respective fluorides. Analogously halide substituted carboranes were prepared, but their fluoro-derivatives were not obtained. The application of crown ethers in the synthesis of transition metal complexes is relatively unexplored. The usual synthesis of fluoro-derivative transition metal complexes involves highly reactive and toxic fluorinating agents such as antimony trifluoride, antimony penta fluoride. bromine trifluoride and hydrogen fluoride, An attempted preparation of the hexafluoroosmate (IV) ion via a crown activated, or naked fluoride~was unsuccessful. Potassium hexafluoroosmate (IV), K208F6. was eventually prepared using bromine trifluoride as a fluorinating and oxidizing agent .

Involvement of free radicals in peroxidatic reactions catalyzed by chloroperoxidase

The mechanism of chloroperoxidase (CPO)-catalyzed peroxidatic reactions of several substituted hydroquinones was studied at various hydrogen peroxide concentrations. The pathway was studied using cytochrome c as the radical trapping agent. As the hydroquinones became more hindered there was a difference in the amount of radicals trapped. For hydroquinone, 59.3% radical pathway, and methylhydroquinone, 81.4% radical, the difference in radicals trapped is due to a difference in pathway. For 2,3-dimethylhydroquinone (75.4%), trimethylhydroquinone (44.5%), and t-butylhydroquinone (0%) other non-peroxidatic reactions are noticed. Thus, for the more substituted hydroquinones the difference in radicals trapped can not be assigned to a difference in radical pathway. Also, there were problems drawing conclusions for this system due to the catalytic reaction of hydrogen peroxide. The radical trapping ability of 2,4,6-trimethylphenol was investigated for various other substrates. TMP reacted with the radicals generated in the enzymatic reactions of phenol, resorcinol, and m-methoxyphenol. Thus, this TMP system offers further potential as another radical trapping agent for use in these studies.

Introducao ao estudo de fluxos para arco submerso

O maior objetivo deste trabalho foi estudar os efeitos da composição dos fluxos para arco submerso sobre algumas importantes características de um metal de solda ferrítico, como composição química, microestrutura, propriedades mecânicas e geometria do cordão. Para realizar tal pesquisa, vinte oito fluxos aglomerados foram elaborados de compostos de pureza comercial e utilizados em soldagens ao aorco submerso, mantendo constante todas as demais condições de soldagem. Houve uma notável influência da composição química e do índice de basicidade dos fluxos sobre os níveis de oxig~enio, silício e manganês do metal de solda. Um modelo termodinâmico, baseado no conceito de potencial de oxigênio, foi proposto para explicar as reações gás-meta-escória ocorrendo durante a soldagem. Este modelo mostrou-se usável para as reações entre silício, oxigênio e carbono, permitindo um melhor entendimento das mesmas. A composição química do metal de solda pôde ser relacionada a sua microestrutura, através de metalografia quantitativa. Foi observado que oxigênio, silício, manganês e titânio têm grande influência sobre ela. A fase mais tenaz encontrada foi a ferrita acicular. A respeito da geometria do cordão, a sílica mostrou o efeito mais forte, com os outros compostos influenciando somente o acabamento do cordão soldado.

Monitoramento morfológico do xerogel híbrido 3-(1,4-fenilenodiamina)propil/silica obtido sob diferentes condições de síntese

Neste trabalho, foi obtido o xerogel híbrido 3-(1,4-fenilenodiamina) propil/sílica, usando-se o método sol-gel de síntese, variando-se as condições experimentais de síntese. Foram usados como reagentes precursores o tetraetilortosilicato (TEOS) e o 3-[(1,4-fenilenodiamina)propil]trimetoxisilano (FDAPS) sintetizado em nosso laboratório. As condições experimentais de síntese variadas foram: a concentração de precursor orgânico (FDAPS), a temperatura de gelificação, o tipo de solvente e o pH do meio reacional. O trabalho foi dividido em duas etapas: na primeira, foram obtidas duas séries de materiais onde se variou a temperatura de gelificação (5, 25, 50 e 70 °C), além da quantidade de precursor orgânico (FDAPS), adicionado à síntese (1,5 e 5,0 mmol). Na segunda etapa variou-se o pH do meio reacional (4, 7 e 10) além do tipo de solvente (etanol, butanol e octanol), mantendo-se a quantidade de precursor orgânico adicionado e a temperatura de gelificação constantes em 5,0 mmol e 25 oC, respectivamente. Em ambas etapas utilizou-se HF como catalisador e manteve-se o sistema fechado, porém não vedado, durante a gelificação. Na caracterização dos xerogéis híbridos foram usadas as seguintes técnicas: a) termoanálise no infravermelho, para estimar a estabilidade térmica do componente orgânico além da fração de orgânicos dispersos na superfície; b) isotermas de adsorção e dessorção de nitrogênio, para determinação da área superficial específica, do volume e da distribuição de tamanho de poros; c) análise elementar para estimar a fração de componente orgânico presente no xerogel e d) microscopia eletrônica de varredura onde foi possível observar textura, compactação e presença de partículas primárias nos xerogéis. A partir dos resultados de caracterização foi possível avaliar a influência dos parâmetros experimentais de síntese nas características dos xerogéis híbridos obtidos. Xerogéis híbridos com maior teor de orgânicos foram mais influenciados pela variação da temperatura de gelificação. Um aumento na temperatura de gelificação produz xerogéis com menor porosidade, entretanto, com maior estabilidade térmica do componente orgânico. Considerando-se estabilidade térmica e porosidade, as amostras gelificadas a 25 oC apresentaram os melhores resultados. Em relação à variação de pH e solvente, as amostras gelificadas em pH ácido foram as que apresentaram maior porosidade, enquanto que a maior estabilidade térmica foi alcançada usando-se etanol como solvente.

Novel catalyst systems based on Ni(II), Ti(IV), and Cr(III) complexes for oligo-and polymerization of ethylene

The complex of Brookhart Ni(α-diimine)Cl2 (1) (α-diimine = 1,4-bis(2,6- diisopropylphenyl)-acenaphthenediimine) has been characterized after impregnation on silica (S1) and MAO-modified silicas (4.0, 8.0 and 23.0 wts.% Al/SiO2 called S2, S3 and S4, respectively). The treatment of these heterogeneous systems with MAO produces some active catalysts for the polymerization of the ethylene. A high catalytic activity has been gotten while using the system supported 1/S3 (196 kg of PE/mol[Ni].h.atm; toluene, Al/Ni = 1000, 30ºC, 60 min and atmospheric pressure of ethylene). The effects of polymerization conditions have been tested with the catalyst supported in S2 and the best catalytic activity has been gotten with solvent hexane, MAO as cocatalyst, molar ratio Al/Ni of 1000 and to the temperature of 30°C (285 kg of PE/mol[Ni].h.atm). When the reaction has been driven according to the in situ methodology, the activity practically doubled and polymers showed some similar properties. Polymers products by the supported catalysts showed the absence of melting fusion, results similar to those gotten with the homogeneous systems by DSC analysis. But then, polymers gotten with the transplanted system present according to the GPC’s curves the polydispersity (MwD) varies between 1.7 and 7.0. A polyethylene blend (BPE/LPE) was prepared using the complex Ni(α-diimine)Cl2 (1) (α-diimine = 1,4-bis(2,6-diisopropylphenyl)-acenaphthenediimine) and {TpMs*}TiCl3 (2) (TpMs* = hydridobis(3-mesitylpyrazol-1-yl)(5-mesitylpyrazol-1-yl)) supported in situ on MAO-modified silica (4.0 wts. -% Al/SiO2, S2). Reactions of polymerization of ethylene have been executed in the toluene in two different temperatures (0 and 30°C), varying the molars fraction of nickel (xNi), and using MAO as external cocatalyst. To all temperatures, the activities show a linear variation tendency with xNi and indicate the absence of the effect synergic between the species of nickel and the titanium. The maximum of activity have been found at 0°C. The melting temperature for the blends of polyethylene produced at 0 °C decrease whereas xNi increases indicating a good compatibility between phases of the polyethylene gotten with the two catalysts. The melting temperature for the blends of polyethylene showed be depend on the order according to which catalysts have been supported on the MAO-modified silica. The initial immobilization of 1 on the support (2/1/S2) product of polymers with a melting temperature (Tm) lower to the one of the polymer gotten when the titanium has been supported inicially (1/2/S2). The observation of polyethylenes gotten with the two systems (2/1/S2 and 1/2/S2) by scanning electron microscopy (SEM) showed the spherical polymer formation showing that the spherical morphology of the support to been reproduced. Are described the synthesis, the characterization and the catalytic properties for the oligomerization of the ethylene of four organometallics compounds of CrIII with ligands ([bis[2-(3,5-dimethyl-1-pyrazolyl)ethyl]amine] chromium (III) chloride (3a), [bis[2-(3,5- dimethyl-l-pyrazolyl)ethyl]benzylamine] chromium (III) chloride (3b), [bis[2-(3,5-dimethyl-lpyrazolyl) ethyl]ether] chromiun(III)chloride (3c), [bis[2-(3-phenyl-lpyrazolyl) ethyl]ether]chromiun(III)chloride (3d)). In relation of the oligomerization, at exception made of the compounds 3a, all complex of the chromium showed be active after activation with MAO and the TOF gotten have one effect differentiated to those formed with CrCl3(thf)3. The coordination of a tridentate ligand on the metallic center doesn't provoke any considerable changes on the formation of the C4 and C6, but the amount of C8 are decrease and the C10 and C12+ have increased. The Polymers produced by the catalyst 3a to 3 and 20 bar of ethylene have, according to analyses by DSC, the temperatures of fusion of 133,8 and 136ºC respectively. It indicates that in the two cases the production of high density polyethylene. The molar mass, gotten by GPC, is 46647 g/mols with MwD = 2,4 (3 bar). The system 3c/MAO showed values of TOF, activity and selectivity to different α-olefins according to the pressure of ethylene uses. Himself that shown a big sensibility to the concentration of ethylene solubilized.

Crisis communication: organization's reactions to unexpected events

A reputação é considerada o ativo mais importante das empresas. Ela permite o estabelecimento de relações comerciais e garante um bom funcionamento da organização. Quando um evento inesperado surge, a reputação pode ser ameaçada. Os gerentes, líderes da organização, têm então que demonstrar reatividade e capacidade em responder as necessidades dos stakeholders, e capacidade de detectar e consertar as falhas dentro da organização através de um processo de aprendizagem, para evitar conseqüências negativas que poderiam danificar a reputação e impactar o desenvolvimento operacional da empresa. Através da comunicação de crise, observamos que depois da queda do avião AF 447, a companhia Air France adotou diferentes posturas adaptadas ao pedido dos stakeholders e ao grau de ameaça sofrido. Logo depois do acidente, a empresa decidiu adotar a estratégia do reconhecimento, assumindo uma responsabilidade simbólica e comunicando prioritariamente para as famílias das vitimas e para a mídia. Nas seguintes semanas ela utilizou a estratégia do silêncio que consiste em não comunicar diretamente a mídia. Finalmente, ela usou a estratégia do “bode expiatório” quando ela foi sujeita a ataques diretos. As reações da empresa somadas ao avanço das investigações judiciais revelaram falhas organizacionais “históricas” dentro da própria empresa, como por exemplo, a falta de comunicação entre pilotos e gerentes ou uma falha de sensibilidade técnica e operacional da parte dos gerentes. Apesar de problemas interno e externo, a Air France demonstrou que uma comunicação de crise bem gerenciada limita os impactos financeiros e de reputação. As conseqüências negativas sofridas pela companhia Air France foram limitadas.

Contribuição ao estudo da argamassa com adição de silica ativa em reforços de elementos comprimidos de concreto

VASKE, N.R. Contribuição ao Estudo da Argamassa com Adição de Sílica Ativa em Reforços de Elementos Comprimidos de Concreto. 2004. Dissertação (Mestrado em Engenharia) – Programa de Pós-Graduação em Engenharia Civil, UFRGS, Porto Alegre. No uso de argamassa com adição de sílica ativa como material de reforço, adotam-se valores de resistência à compressão provenientes de ensaios normatizados, cujos valores não são representativos da técnica adotada. Na execução de um reforço, cada porção de argamassa que é lançada sofre um adensamento que varia em função da energia com que colide com o substrato, gerando, desta forma, pontos de diferentes resistências por toda a extensão do reforço, refletindo diretamente sobre a resistência do reforço como um todo, que por sua vez define a nova capacidade de carga do elemento estrutural em questão. Procurando verificar o comportamento “in loco” da argamassa de reforço, executou-se uma placa de argamassa com adição de sílica ativa com dimensões iguais a um reforço de uma das faces de um pilar, sendo extraídas amostras prismáticas desta placa e ensaiadas à compressão e determinada uma resistência média que, comparada com a resistência média obtida de corpos-de-prova cilíndricos, moldados com a mesma argamassa com que foi executada a placa demonstrou que a resistência média à compressão das amostras prismáticas extraídas da placa apresenta, particularmente neste estudo, uma redução em relação à resistência média à compressão resultante dos corpos-de-prova cilíndricos da ordem de 35%. Em seqüência foram moldados seis pilares de concreto, sendo três reforçados com argamassa com adição de sílica ativa e os outros três como testemunhos. Após a ruptura dos pilares foram analisados os resultados teóricos e resultados experimentais das cargas de ruptura, aderência entre o substrato e a argamassa de reforço e a redução de resistência à compressão observada nos ensaios preliminares da argamassa. Pelas análises realizadas verificou-se a eficiência da técnica de reforço quanto ao aumento da capacidade de carga, da ordem de 72 %, aderência adequada entre o substrato e a argamassa de reforço e confirmação da redução da resistência à compressão da argamassa nos níveis propostos.

Controle da porosidade em fases vítreas formadas pela ação de fundentes em cerâmicas gresificadas

O presente trabalho teve como objetivo investigar os fenômenos que controlam a porosidade em corpos cerâmicos com fases vítreas, formadas pela ação de fundentes, e associá-los com sua microestrutura final. Foram selecionados os fundentes albita, feldspato alcalino, wollastonita e espodumênio, representativos daqueles comercializados no setor cerâmico, a partir de critérios como teor e tipo de álcali, e teor em SiO2 e Al2O3 na composição química. Estes fundentes foram formulados com cada uma das seguintes matérias-primas e combinações destas: quartzo, caulim e talco. As composições foram formuladas com o objetivo de obter-se uma gama de diferentes microestruturas, variando porosidade, e a presença de fases vítreas ou cristalinas. Os corpos cerâmicos foram obtidos em fornos elétricos, tipo mufla, variando-se a temperatura entre 1140 e 1260°C, conforme a formulação investigada. Foram determinadas as propriedades dos corpos cerâmicos, como porosidade aparente, absorção de água e retração linear. Os resultados obtidos foram associados com sua microestrutura e formulação. Para tanto, fez-se uso de microscopia eletrônica de varredura e difratometria de raios-X. Em especial, a porosidade foi avaliada quanto sua distribuição, morfologia e tamanho, e sua influência na definição da microestrutura final, e relação com propriedades dos corpos cerâmicos investigados. Os resultados obtidos indicaram que o comportamento dos fundentes em massas cerâmicas define decisivamente a formação da porosidade em função da composição química do fundente e da combinação desta com a dos outros constituintes da massa cerâmica. O espodumênio forma fase vítrea reagindo basicamente com o quartzo em baixas temperaturas, retendo a porosidade principalmente junto às trincas de contração do mesmo. A albita propicia na expansão da porosidade e interconexão da mesma. O feldspato alcalino forma um líquido de maior viscosidade mantendo a menor porosidade e de maneira mais isolada. A wollastonita reage de modo diferenciado dos demais no que diz respeito à sílica presente, reagindo melhor na presença do alumínio e do magnésio.